Effect of jet-to-plate spacing in laminar array jets impinging

The rate of heat transfer from a plate due to impinging of an array of jets was investigated. The effect of jet-to-plate spacing in a confined array of impinging laminar square jets was investigated numerically through the solution of Navier Stokes and energy equations. The simulation is carried out for the jet-to-plate spacing between 2 B and 20 B and for jet-to-jet spacing of 4 B, where B is the jet width. Five in-line jets subjected to across-flow were used in this investigation. Also, six different ratios of jet to cross-flow velocity are simulated (0.5, 1.0, 2.5, 5, 7.5 and 10) for the jet Reynolds number of 200. The predicted results show a formation of one or two ground horseshoe vortices between the jets. In addition, a horseshoe vortex forms at different position between the orifice and impinging plates due to the interaction of two jets before they combine. The number of the ground horseshoe vortex and its size are strongly affected by the jet-to-plate spacing and by jet to cross-flow velocity ratio. The effect of jet-to-plate spacing and jet to cross-flow velocity ratio on heat transfer is presented and discussed.     

Large-Eddy Simulations of Forced Three-Dimensional Impinging Jets

Large-eddy simulations of the flow field around twin three-dimensional impinging jets were carried out to simulate the near-ground hover configuration of a vertical takeoff and landing (VTOL) aircraft. Both the impinging jet and the upwash caused by the collision of the wall jets are modeled in this study. The evolution of the vortical structures in the impinging jet flow field, due to the introduction of axisymmetric and azimuthal perturbations at the jet exit, has been investigated. The vortical structures formed in the jet shear layer due to azimuthal forcing, show significant three-dimensional vortex stretching effects when compared to the structures formed during axisymmetric forcing. Breakdown of the large-scale structures into smaller vortices also occurs much earlier during azimuthal forcing. When compared to the upwash formed during axisymmetric forcing, the azimuthally perturbed jet forms an upwash that is less coherent and results in a weaker upload or lift-off force on the aircraft undersurface. Comparison with available experimental data indicates good agreement for the centerline velocity decay, the wall pressure variation and the phase speed of the vortical structures.     

Opposed round jets issuing into a small aspect ratio channel cross flow

Round jets (diameter D) discharging into a confined cross flow (dimension 3.16D × 21.05D) are investigated experimentally. Two configurations are considered: (1) a single jet (momentum flux ratio, J = 155) and (2) two opposed jets with two different momentum flux ratios (J = 60, and 155). A two-component laser-Doppler anemometer is used to make a detailed map of the normal stresses and mean velocities in the symmetry plane of the jets. In addition, smoke-wire and laser-sheet visualization are used to study the flow.

The rate of bending of the single confined jet is found to be higher than the rate of bending of an unconfined jet with the same momentum flux ratio. In the far field, the jet centerline velocity is observed to decay more slowly than the unconfined jet, indicating poor turbulent diffusion of linear momentum. Annular shear layer vortices are visualized on the upstream edge of the jet in the near field. In the far field, the flow visualization suggests that the jet loses its integrity and fragments into independent regions that are convected by the cross flow.

In the opposed jet configuration at the high momentum flux ratio (J = 155), the jets impinge in the center of the duct, and a pair of vortices is observed upstream of the impingement region. The flow visualization implies that the impingement vortices form quasi periodically and have a finite life span. In the impingement region, the jets are observed to penetrate alternately beyond the symmetry plane of the duct. In the two-jet configuration with J = 60, the jets do not impinge on each other owing to the higher rate of bending. Instead, the flow visualization indicates that the shear layers of the jets penetrate to the central region and periodically pinch off regions of the potential-like cross-flow fluid where they meet. The pinch-off regions of cross-flow fluid are convected by the turbulent flow for large distances, yet remain essentially unmixed.     

A numerical and experimental investigation of the interactions between a non‐uniform planar array of incompressible free jets

The interaction between multiple incompressible air jets has been studied numerically and experimentally. The numerical predictions have been first validated using experimental data for a single jet configuration. The spreading features of five unequal jets in the configuration of one larger central jet surrounded by four smaller equi‐distant jets, have been studied, for different lateral spacing ratios of 1.5, 2.0 and 2.5 and a central jet Reynolds number of 1.24×105 (corresponding to a Mach number of 0.16). Flow of five equal jets has also been simulated, for the sake of comparison. The jet interactions commence at an axial distance of about 3–4 diameters and complete by an axial distance of about 10 diameters for the lowest spacing ratio of 1.5. For larger spacing ratios, the length required for the start and completion of jet interaction increase. Peripheral jets bend more towards the central jet and merge at a smaller distance, when their sizes are smaller than that of the central jet. The entrainment ratio for multiple jets is higher than that for a single jet. Excellent agreement is observed between the experimental data and theoretical predictions for both mean flow field and turbulent quantities, at regions away from the jet inlet. The potential core length and initial jet development, however, are not predicted very accurately due to differences in the assumed and actual velocity profiles at the jet inlet. Copyright © 2004 John Wiley & Sons, Ltd.     

Numerical study of unsteady flow and heat transfer of circular tangential direction jets flowing over the inner cylinder surface in the annular chamber

In order to understand the dynamics of vortices on heat transfer, the unsteady flow field of tangential direction jets flowing in the annular chamber is numerically investigated by scale-adaptive simulation (SAS). The jet Reynolds number is 332,000 based on the jet’s diameter and inflow velocity for a specific geometric model. The analogy theory is used to obtain the convective heat transfer coefficient distribution on the hub surface. Spectral analysis via fast Fourier transform (FFT) is used to analyze frequency information that flows inside the chamber. The proper orthogonal decomposition (POD) method is performed on the velocity field in the chamber and the convective heat transfer coefficient on the hub surface using a snapshot method. The fast Fourier transform helps find the dominant frequency of the unsteady flow in the chamber. The time sequence of velocity fields on the radial plane shows the presence of cyclic flapping of the jet. The proper orthogonal decomposition analysis indicates that the unsteady periodic flow phenomenon in the chamber and unsteady heat transfer on the hub surface are mainly related to the dynamics of the counter-rotating vortices caused by the jet.     

Interaction of Multiple Gas Jets Horizontally Injected into a Vertical Water Stream

A gas jet injected horizontally into a descending vertical water flow has two stable states corresponding to the presence or absence of a gas pocket on the injection wall. Injecting multiple parallel jets gives rise to complex interactions dominated by two phenomena: the presence or absence of a gas pocket and the periodic movements of the jets. The very low frequency of these movements (approx. 1 Hz) is essentially correlated with crossflow velocity and jet spacing. Different types of interaction were observed over a wide range of experimental conditions. In particular, a zone of interdependence was evidenced where interaction between jets leads to the coexistence of jets with and without a gas pocket. The influence of different experimental parameters was defined. A better understanding of the mechanism of jet interaction is obtained, especially the conditions of movement of vortices and the significance of the water flow confined between the jets which modifies their mean dimensions (20 to 40% increase in length and height, decrease of width without coalescence). This revised version was published online in July 2006 with corrections to the Cover Date.     

Characteristics of strongly-forced turbulent jets and non-premixed jet flames

Previous researchers have demonstrated that strong pulsations of the fuel flow rate can significantly reduce the flame length and luminosity of laminar/transitional non-premixed jet flames. The physical mechanisms responsible for these changes are investigated experimentally in acoustically-forced jet flows where the peak velocity fluctuations are up to eight times the mean flow velocity. Both reacting and non-reacting flows were studied and Reynolds numbers, based on the mean flow properties, ranged from 800 to 10,000 (corresponding to peak Reynolds numbers of 1,450–23,000), and forcing frequencies ranged from 290 to 1,140 Hz. Both the first and second organ-pipe resonance modes of the fuel delivery tube were excited to obtain these frequencies. An analysis of the acoustic forcing characteristics within the resonance tube is provided in order to understand the source of the high amplitude forcing. Flow visualization of jets with first resonant forcing confirms the presence of large-scale coherent vortices and strong reverse flow near the exit of the fuel tube. With second-resonant forcing, however, vortices are not emitted from the tube as they are drawn back into the fuel tube before they can fully form. Increased fine-scale turbulence is associated with both resonant cases, but particularly at second resonance. The power spectra of the velocity fluctuations for a resonantly pulsed jet show the presence of an inertial subrange indicating that the flow becomes fully turbulent even for mean-Reynolds-number jets that are nominally laminar. It is shown that these pulsed jet flows exhibit strong similarities to synthetic jets and that the Strouhal number, based on the maximum velocity at the fuel tube exit, is the dominant parameter for scaling these flows. The Strouhal number determines the downstream location where the coherent vortices breakdown, and is found to provide better collapse of flame length data (both current and previous) than other parameters that have been used in the literature.     

Flow and breakup characteristics of elliptical liquid jets

This paper presents the results of an experimental study on liquid jets discharging from elliptical orifices into still ambient air. The experiments were conducted with a set of elliptical orifices of approximately same area of cross section but varying orifice aspect ratio using water and water–glycerol mixture as experimental fluids. The flow behavior of liquid jets was analyzed using their photographs captured by an imaging system. The measurements obtained for the elliptical liquid jets were compared with the circular liquid jets discharging from a circular orifice of the same area of cross section. Elliptical geometry of the orifice results in a flow process by which the emanating liquid jet periodically switches its major and minor axes as it flows downstream of the orifice. In this paper, we attempt to characterize the axis-switching process through its wavelength and amplitude. For a given elliptical orifice, the axis-switching process is dominantly seen in a particular range of flow conditions. The effects of the orifice aspect ratio and liquid viscosity on the axis-switching process are revealed through this study. The experimental results on jet breakup show that axis-switching process has a destabilizing effect on elliptical liquid jets within a particular range of flow conditions and it results in shorter breakup lengths compared to the circular jet. The extent to which axis-switching destabilizes the jet is dictated by the viscosity of liquid. An increase in orifice aspect ratio destabilizes elliptical liquid jets with low viscosity like water; however, this behavior seems to get obscured in water–glycerol mixture elliptical jets due to high viscosity.     

同轴交叉射流的轴线速度

研究了射流交叉角度和密度比对同轴交叉射流流场的影响。基于动量守恒原理,提出了考虑径向流动和密度差别的同轴交叉射流的当量直径和当量速度。当量速度与Dual PDA的实验结果较为吻合。该法可较好地描述射流交叉角度、密度比对轴线上轴向速度的影响。     

Population,characteristics and kinematics of vortices in a confined rectangular jet with a co-flow

Vortex behavior and characteristics in a confined rectangular jet with a co-flow were examined using vortex swirling strength as a defining characteristic. On the left side of the jet, the positively (counterclockwise) rotating vortices are dominant, while negatively rotating vortices are dominant on the right side of the jet. The characteristics of vortices, such as population density, average size and strength, and deviation velocity, were calculated and analyzed in both the cross-stream direction and the streamwise direction. In the near-field of the jet, the population density, average size and strength of the dominant direction vortices show high values on both sides of the center stream with a small number of counter-rotating vortices produced in the small wake regions close to jet outlet. As the flow develops, the wake regions disappear, these count-rotating vortices also disappear, and the population of the dominant direction vortices increase and spread in the jet. The mean size and strength of the vortices decrease monotonically with streamwise coordinate. The signs of vortex deviation velocity indicate the vortices transfer low momentum to high-velocity region and high momentum to the low velocity region. The developing trends of these characteristics were also identified by tracing vortices using time-resolved particle image velocimetry data. Both the mean tracked vortex strength and size decrease with increasing downstream distance overall. At the locations of the left peak of turbulent kinetic energy, the two-point spatial cross-correlation of swirling strength with velocity fluctuation and concentration fluctuation were calculated. All the correlation fields contain one positively correlated region and one negatively correlated region although the orientations of the correlation fields varied, due to the flow transitioning from wake, to jet, to channel flow. Finally, linear stochastic estimation was used to calculate conditional structures. The large-scale structures in the velocity field revealed by linear stochastic estimation are spindle-shaped with a titling stream-wise major axis.     

Dynamics of swirling jet flows

Experimental investigations of near-field structure of coaxial flows are presented for four different configurations: coaxial jets without rotation (reference case), outer flow rotating only (OFRO), inner-jet rotating only (IJRO) and corotating jets (CRJ). The investigations are performed in a cylindrical water tunnel, with an independent rotation of two coaxial flows. Laser tomography is used to document the flow field, and photographs are shown for different configurations. Time mean velocity profiles obtained by PIV, with and without swirl, are also presented. The dynamics of the swirling jets in the initial region (i.e. near the exit of the jets) is described. The effects of azimuthal velocity and axial velocity ratio variations on flow dynamics are examined. The appearance and growth of the first instabilities are presented and compared with some theoretical results, as is the influence of the rotation (inner or outer) on the dominating structures.     

Investigation of two plane paralleltiinven ilated jets

Measurements of mean velocity components, mean flow direction, turbulent intensities and Reynolds shear stress were made with a split film probe of hot wire anemometer to investigate the flow field generated by two identical jets of air issuing from plane parallel nozzles in a common end wall and mixing with the ambient room air. Due to the sensitivity of the split film probe to the flow direction, the reverse flow in the converging region was detected by the split film probe and observed by flow visualization. The mean velocity approaches self-preservation in both the converging and the combined regions, while the turbulent intensities and Reynolds shear stress approach self-preservation in the combined region only. The trajectory of the maximum velocity is almost unchanged by variance of nozzle spacing in the converging region. The distance of the merging point from the nozzle exit increases linearly with nozzle spacing. The spread of the converging jet increases more rapidly than that of the combined jet.     

ROUNDED FLOWING STATES OF OBSTRUCTED BUOYANT JET

The mutual relationships of three effective factors, the diameter D/d (d is the diameter of exit) of obstructed plate, exit densimetric Froude number and the distance H/d of the plate from jet orifice for obstructed buoyant jet in static ambient, are analyzed to explain normal and abnormal rounded flowing (reverberated and bifurcated flowing). The critical Froude numbers for obstructed buoyant jets with H/d=2, 4, 6, 8 which distinguished normal and abnormal flowing pattern are obtained. Normal rounded flowing is found only for a plate under a special value of H/d. A fitted formula of critical Froude numbers with H/d and D/d is presented to distinguish rounded flowing types. The occurring of reverberated or bifurcated flowing in abnormal rounded flow is analyzed. Based on the results of obstructed buoyant jets with D/d=1, normal rounded flowing occurred only for all conditions and axial dilution behind the plate under different H/D is obtained.     

Self-sustained global oscillations in a jet in crossflow

A jet in crossflow with an inflow ratio of 3, based on the maximum velocity of the parabolic jet profile, is studied numerically. The jet is modeled as an inhomogeneous boundary condition at the crossflow wall. We find two fundamental frequencies, pertaining to self-sustained oscillations in the flow, using full nonlinear direct numerical simulation (DNS) as well as a modal decomposition into global linear eigenmodes and proper orthogonal decomposition (POD) modes; a high frequency which is characteristic for the shear-layer vortices and the upright vortices in the jet wake, and a low frequency which is dominant in the region downstream of the jet orifice. Both frequencies can be related to a region of reversed flow downstream of the jet orifice. This region is observed to oscillate predominantly in the wall-normal direction with the high frequency, and in the spanwise direction with the low frequency. Moreover, the steady-state solution of the governing Navier?CStokes equations clearly shows the horseshoe vortices and the corresponding wall vortices further downstream, and the emergence of a distinct counter-rotating vortex pair high in the free stream. It is thus found that neither the inclusion of the jet pipe nor unsteadiness is necessary to generate the characteristic counter-rotating vortex pair.     

Linear instability characteristics of incompressible coaxial jets

The present study deals with the local linear instability of axisymmetric coaxial jets with a duct wall separating the two streams. The flow is assumed to be locally parallel, inviscid and incompressible. The objective of the work is to understand how the various parameters describing this flow geometry (i.e. boundary layers thicknesses at the exit, velocity ratio, wall thickness) may influence the instability of the flow and, in particular, the convective/absolute instability transition. A specific family of profiles is chosen for the modelling of the mean undisturbed flow and a spatial stability analysis is performed in order to identify the unstable modes and to assess how they are affected by the wake region behind the wall. An absolutely unstable mode is found, and its characteristics, depending on the velocity ratio and shear layers thicknesses, are determined. Results show that the absolute unstable mode is present only for a limited range of velocity ratios and that the corresponding frequency is almost constant if normalized with the mean velocity and wake thickness. This frequency value and the extension of the range of velocity ratios is similar to those found in the experiments on a similar geometry. Finally, a specific velocity ratio is found that maximizes the region at the jet exit for which an absolute instability behind the wall is present. This may increase the possibility for the onset of a global mode that may sustain the instability of the whole jet, enhancing considerably the mixing and entrainment characteristics between the two streams.     

Unsteady effects in mechanically-excited turbulent plane jets

Two methods of mechanically exciting a plane turbulent free jet are described; periodic perturbatin of the nozzle exit velocity, and forced oscillation of a small vane located in the het potential core. Hot-wire measurements obtained by conditional sampling techniques indicated that the flow fields of the two jets are substantially different although they have the same Strouhal number of 0.0032. While the mean flow development of the pulsed jet can be described adequately by a quasi-steady model, the vane-excited jet exhibits unsteady effects which depart significantly from quasi-steady approximations such as increased entrainment, amplification of excitation and non-linear effects in the form of the presence of high harmonics. The constancy of momentum flux has been examined in both the steady and unsteady jets     

出口条件对圆形湍流射流远场区自保持性的影响

报道出口条件对圆形湍流射流自保持性影响的实验研究结果. 对来自渐缩和长管两种不同结构喷嘴的射流,在相同雷诺数条件下,沿轴线进行了速度测量; 研究的统计量包括平均速度、湍流强度、高阶矩、能谱和积分尺度. 实验结果表明,渐缩喷嘴射流比长管射流发展得更快、更容易达到自保持状态. 通过对比发现,在两射流的速度(温度)场中,平均速度(温度)、湍流强度、偏斜因子和平坦度因子都存在明显的异同. 同时发现两射流的积分尺度随轴向距离的增加都成线性增长,且在渐缩喷嘴射流中增长得更快. 通过对比两射流的边界层厚度、径向与轴向湍流强度的比值、湍动能能谱图并结合前人的研究结果,对两射流湍流场所表现出的不同的统计学行为给出了合理的解释.      

微型射流涡流器对湍流边界层控制的数值研究

运用数值方法,模拟出展向分布的同向倾斜微型射流列与平板湍流边界层相互作用形成流向涡列的流场结构,验证了利用其来对湍流边界层进行控制的可能性.随射流间距减小,流向涡列控制作用流向渗透能力增强,但作用区域减小;随射流速度提高,流向涡列控制作用增强,但过大的射流速度反而会导致流向涡列在局部区域内控制作用的下降;随射流俯仰角减小、倾斜角增大,流向涡列初始控制作用增强,但过小的俯仰角、过大的倾斜角会导致流向涡列流向控制区域明显缩小.要保证流向涡列具有较强的湍流边界层控制作用,必须通过合理配置射流列各主要参数,在保证各流向涡具有一定强度的同时,还要确保各流向涡在形成时部分嵌入边界层内部.     

Measurements in the near flow field of an isosceles triangular turbulent free jet

The near field mean flow and turbulence characteristics of a turbulent jet of air issuing from a sharp-edged isosceles triangular orifice into still air surroundings have been examined experimentally using hot-wire anemometry and a pitot-static tube. For comparison, some measurements were made in an equilateral triangular free jet and in a round free air jet, both of which also issued from sharp-edged orifices. The Reynolds number, based on the orifice equivalent diameter, was 1.84×10⁵ in each jet. The three components of the mean velocity vector, the Reynolds normal and primary shear stresses, the one-dimensional energy spectra of the streamwise fluctuating velocity signals and the mean static pressure were measured. The mean streamwise vorticity, the half-velocity widths, the turbulence kinetic energy and the local shear in the mean streamwise velocity were obtained from the measured data. It was found that near field mixing in the equilateral triangular jet is faster than in the isosceles triangular and round jets. The mean streamwise vorticity field was found to be dominated by counter-rotating pairs of vortices, which influenced mixing and entrainment in the isosceles triangular jet. The one-dimensional energy spectra results indicated the presence of coherent structures in the near field of all three jets and that the equilateral triangular jet was more energetic than the isosceles triangular and round jets.     

Time resolved investigations on flow field and quasi wall shear stress of an impingement configuration with pulsating jets by means of high speed PIV and a surface hot wire array

The effects of jet pulsation on flow field and quasi wall shear stress of an impingement configuration were investigated experimentally. The excitation Strouhal number and amplitude were varied as the most influential parameters. A line-array with three submerged air jets, and a confining plate were used. The flow field analysis by means of time resolved particle image velocimetry shows that the controlled excitation can considerably affect the near-field flow of an impinging jet array. These effects are visualized as organization of the coherent flow structures. Augmentation of the Kelvin–Helmholtz vortices in the jet shear layer depends on the Strouhal number and pulsation magnitude and can be associated with pairing of small scale vortices in the jet. A total maximum of vortex strength was observed when exciting with Sr = 0.82 and coincident high amplitudes.Time resolved interaction between impinging vortices and impingement plate boundary layer due to jet excitation was verified by using an array of 5 μm surface hot wires. Corresponding to the global flow field modification due to periodic jet pulsation, the impact of the vortex rings on the wall boundary layer is highly influenced by the above mentioned excitation parameters and reaches a maximum at Sr = 0.82.