透射式能见度仪动态范围扩展方法

提出了一种利用光学衰减片与电机组合,扩展透射式能见度仪动态范围的方法。通过改变加载到LED光源的调制信号的幅度,控制LED光源的发射光强;设计测量系统,选择固定透过率的衰减片;设置合理的系统阈值完成数据测量。对测量数据作拟合分析,结果表明:采用透过率为60%的中性密度衰减片,系统动态范围扩展了0.6倍;透过率为12%时,系统动态范围扩展了6.9倍。同时,通过选择不同透过率的中性密度衰减片,可实现系统动态范围的灵活扩展。     

Variable photonic crystal fiber optical attenuator combining air hole reduction induced radiation and bending loss

Recently, an optical attenuator has been important in fiber optic communication systems, because a transmission power in fiber has become higher due to a channel increment in wavelength division multiplexing transmission. A photonic crystal fiber (PCF) optical attenuator is fabricated by air hole diameter reduction in a part of PCF in which radiations are caused in the air hole diameter reduced part of PCF. A PCF optical attenuator has a high power resistance feature due to its radiation-induced operation of optical attenuation. In this paper, we proposed a variable PCF optical attenuator in which a bend was applied to the air hole diameter reduced part in PCF optical attenuator that was fabricated by CO₂ laser irradiation. In PCF optical attenuator fabrication, the attenuation was adjusted by the reduced air hole diameter with laser irradiation time control. It was demonstrated that 10.6–13.5 dB of variable attenuation was obtained at 1550 nm-wavelength with 0°–90° bending angle applied to the air hole diameter reduced part in PCF optical attenuator.     

可调谐激光二极管吸收光谱系统信号分析及谱线畸变校正技术研究

利用可调谐激光二极管吸收光谱技术进行气体检测时,波长调制伴随的光强幅度调制,会使解调出的谐波谱线发生畸变.在傅里叶分析的基础上对可调谐激光二极管吸收光谱任意调制幅度的波长调制光谱信号进行了分析,给出了光强幅度调制引起吸收谱线畸变的理论解释.提出了在波长调制过程中进行旧步平抑幅度调制的方法来消除谱线畸变,设计了实验方案并...     

拉曼放大辅助波长可选择的全光开关

使用3-dB耦合器组成M-Z干涉仪,在M-Z干涉仪的一臂加入高非线性光纤(HNLF)组成的反向拉曼放大器,改变放大器的泵浦波长及强度,可实现波长可选择的全光开关。其功能可用于波分复用(WDM)系统,对不同波长的上、下载选择有很大的应用意义。理论分析了实现这一功能的可行性和参数选择,考虑拉曼放大并伴有交叉相位调制(XPM)引起信号光的相移,推导分析了在引入放大的同时又引入相移,怎样选择放大和相位匹配问题,来实现波长可选择的光开关的要求。     

Theoretical research on the performance of a practical helix travelling wave tube

On the basis of a rigorous field theory, two different physical models of attenuator and sever have been proposed. One is named High attenuation （HATT） model in which both attenuator and sever are considered as a unified attenuator, but the sever is regarded as an area of very high loss; the other is called Sever and attenuator （SATT） model in which the sever is modelled as a drift area in which the electric and magnetic fields both vanish. A complex function is derived and potential sinking effect is also considered. Thus, a set of more practical self-consistent equations of nonlinear beam-wave interaction is formulated. Simulations are carried out under the conditions of the two different physical models, and the simulation results are compared with the experimental data. The results show that in the case of single signal drive, the unknown second harmonic should be included for predicting the saturated output power. It is also evident that the SATT model and the HATT model predict the same physical nature, whereas the results predicted by the HATT model are much closer to the experimental data than those obtained from the SATT model. Therefore, these results provide a strong theoretical basis for designing broadband and high gain helix travelling wave tubes.     

Design and analysis of two-dimensional photonic crystals channel filter

A novel three-port channel add/drop filter consisting of two waveguides and two cavities is proposed. One is used for a resonant tunneling-based channel add/drop operation from the bus waveguide to the add/drop waveguide, while the other is used to realize the wavelength-selective reflection feedback in the bus waveguide. By means of coupled mode theory in time, the conditions to achieve 100% add efficiency are derived thoroughly. Based on these theoretical analysis, the channel add filter and some other multi-channel filters are designed in two-dimensional photonic crystals (2D PCs) with square lattice of dielectric rods in air. The numerical results by using the finite-difference time-domain (FDTD) method demonstrate almost complete channel add/drop tunneling at resonance via the three-port systems.     

Free-space 1×2 wavelength-selective switches for wavelength-division multiplexing optical networks

A free-space 1 ×2 wavelength-selective switch （WSS） based on thin-film filter technology is proposed. The 1 × 2 WSS is fabricated with an electromagnetic actuator, a reflecton prism, a narrow-band thin-film filter, and three fiber collimators. The working principle and the configuration of WSS are illuminated. The experimental results indicate a fiber-to-fiber insertion loss ranging from 1.109 to 1.249 dB with 2-V voltage input, which satisfies the application of optical fiber communication.     

新型高性能光控高温超导微波可变衰减器研制

 提出了一种用于高温超导系统的新型星载光控高温超导微波可变衰减器，详细介绍了设计过程，并针对测试结果进行了分析。该衰减器的实质是利用液氮温区高温超导薄膜极低的微波表面电阻和卓越的激光响应特性，实现优良的衰减功能。在器件结构的设计上引入过渡材料和透明有机材料以保证器件良好的接地性能以及激光光束的对准。主要结论如下：光控高温超导微波可变衰减器在液氮温区工作，电路尺寸为12 mm×8 mm×0.5 mm，可单独使用也可集成于高温超导系统中，可大幅减小系统的体积与质量；高温超导衰减器的插损小于0.2 dB，比常规衰减器低1个量级；高温超导衰减器的可变衰减步进值小于0.01 dB，比常规衰减器低1～2个量级。根据激光功率大小对衰减器插损变化特性的影响，该衰减器也可以实现步进式调谐。     

0.22 THz高效率行波管的互作用计算

利用CST Microwave Studio 计算双排矩形梳状慢波结构的色散并据此确定了0.22 THz左右频段（D波段）行波管用慢波结构的尺寸参数。将相速再同步技术应用于基于双排矩形梳状慢波结构的D波段行波管中,用CST PIC模拟计算了4例具有不同周期构型的D波段行波管。结果证实:对于无集中衰减器的D波段行波管,在218~232 GHz范围内,相速再同步技术使得输出功率从10~13 W提高到19~28 W,电子效率从1.4%~2.2%提高到2.6%~3.9%;对于具有集中衰减器D波段行波管,在218~232 GHz范围内,相速再同步技术使得输出功率从8~16.8 W提高到32~41 W,电子效率从1.5%~2.8%提高到4.4%~5.7%。此外,无论行波管有无集中衰减器,相速再同步技术都明显改善了行波管的增益平坦度。     

Bending dual-core photonic crystal fiber coupler

In this paper, we systematically study a designed structure of a bending dual-core photonic crystal fiber (PCF). We propose the controllable wavelength-selective coupling PCF. This coupler allows highly accurate control of the filtering wavelength. The different wavelengths can be selected by controlling the bending radius of the fiber. Coupling characteristics of novel bending wavelength-selective coupling PCF are evaluated by using a vector finite element method and their application to a multiplexer demultiplexer (MUX–DEMUX) based on the novel coupler is investigated. When the fiber length is 4168 μm, the bending radius of PCF couplers for 1.48/1.55 μm, 1.3/1.55 μm, 0.98/1.55 μm, and 0.85/1.55 μm is calculated, respectively, and the beam propagation analysis is performed. Different from the traditional wavelength-selective coupling PCF, the dual-core PCF is bent and it can realize the separation of multiple wavelengths.     

Solar-Blind滤光片可见光谱段光密度连续测量

为实现Solar Blind（日盲紫外）滤光片光密度在可见光谱段的高精度连续测试,搭建了以氙灯配合单色仪作为光源、使用单光子计数器作为探测器的测试系统,并对该系统的误差进行分析。系统主要装置有氙灯与单色仪组合的光源,标准衰减装置和单光子计数器;以替代法为基础进行测试,将由单光子计数器探测到的衰减后的计数值作为参考计数值替代光源的初始计数值,通过运算得到滤光片的可见光谱段光密度;该测试系统将滤光片光密度的测试动态范围扩展到0~-11OD,实现了可见光谱段内进行连续光谱测量的功能,且降低了系统的测试误差。与使用窄带LED作为光源的测试系统相比,测试不确定度由2%降低至0.5%,相对重复性误差由0.2％ 降低至0.13％。     

Photonic Crystal Fiber Attenuator

We propose a novel fiber attenuator based on photonic crystal fibers. The difference in the modal field diameters of a conventional single mode fiber and a photonic crystal fiber was used. A variable optical attenuator was also achieved by applying macro-bending on the PCF part of the proposed attenuator     

氙灯光源太阳模拟器辐照衰减器设计方法

针对应用于太阳模拟器辐照衰减器设计上的不足,提出一种新的衰减器设计方法,旨在提高其辐照均匀性.基于光学扩展量计算衰减器上的网孔面积,对会聚光路的辐射通量进行调制;利用聚光镜环带法,理论上分析衰减器上的辐射分布;利用网孔非均匀分布的结构对会聚光路的辐射分布进行调制,给出具体设计参数;对比分析了网孔均匀分布和非均匀分布对辐...     

常用微波衰减器脉冲功率容量测试

提出了一种微波衰减器脉冲功率容量的测试方法,该方法可概括为利用定向耦合器组测试比对法,测试系统主要由微波源、定向耦合器组、衰减器、检波器及示波器等器件及设备组成。选取了广泛应用于高功率微波测试系统的波导衰减器及同轴衰减器进行了功率容量测试。初步测试结果表明:在X波段,对于μs量级脉冲宽度的单脉冲,衰减材料为羟基铁的BJ-100矩形波导式衰减器的脉冲功率容量可达50 kW,厚膜电阻为衰减材料的N型接头的同轴式衰减器的功率容量可达10 kW以上。     

Digitally controlled fault-tolerant multiwavelength programmable fiber-optic attenuator using a two-dimensional digital micromirror device

A digitally controlled multiwavelength variable fiber-optic attenuator using a two-dimensional digital micromirror device (DMD) is introduced. The results from an experimental four-wavelength (i.e., 1546.92, 1548.52, 1550.12, and 1551.72 nm) proof-of-concept attenuator indicate a 26-dB dynamic range and 11-bit resolution. The measured attenuator average coherent optical cross talk per wavelength channel is -38 dB , limited by the additive noise resulting from the nonideal isolation of the optical circulator and the attenuator module. The average optical loss for our experimental attenuator is 15 dB and is limited mainly by the visible-mode DMD that is used as a 1550-nm infrared window device. Our theoretical estimate of a <8-dB loss optimized attenuator can be used for equalization in multiwavelength fiber-optic communications with as many as 108 wavelengths.     

一种双路矢量合成式毫米波预失真线性化器

针对目前行波管放大器模拟预失真技术中存在的幅度和相位特性关联性强的问题,提出一种双路矢量合成式预失真器。该预失真器由90°电桥、模拟电调衰减器和反射式二极管预失真电路构成。根据理论分析和ADS软件仿真结果加工了实际电路并进行测试。实测结果表明:在工作频率29~31GHz和额定输入功率区间内,该电路可实现与行波管特性相反的预失真性能;合理调整两支路偏置电压,可实现相位扩张改变30°,而增益扩张变化量小于1dB的性能,有效减小了模拟预失真器幅度和相位特性的关联性。     

Co(2+)-doped flatband optical fiber attenuator

The attenuation properties of Co(2+) -doped single-mode optical fibers were experimentally and analytically investigated for preparation of a stable flatband attenuator. By controlling the Co(2+) -doped region in a fiber core, we could prepare a flatband attenuator in which the attenuation in wavelengths 1530-1610 nm was held to within 9.9-10.2 dB (3% variation) and the fluctuation of attenuation was less than 0.1 dB with 1-W input power for 100 h.     

Dual wavelength erbium-doped fiber laser with a lateral pressure-tuned Hi-Bi fiber Bragg grating

Tunable dual wavelength erbium-doped fiber laser (EDFL) with stable oscillation at room temperature is proposed and demonstrated. This laser utilizes a Bragg grating fabricated in a high birefringence fiber as the wavelength-selective component, and then achieves the stable dual wavelength oscillation by introducing the polarization hole burning effect. Furthermore, by applying lateral strain upon the fiber Bragg grating (FBG), the space of the laser dual wavelengths can be tuned continuously.     

硅微机械F-腔可变衰减器光学特性分析

一种新型的硅微机械F P腔可变衰减器 ,具有体积小、插入损耗低、调节精度高等优点 ,介绍了其基本结构、基本原理。分析了F P腔两个反射镜的光学特性对F P腔性能的影响 ,包括两反射镜反射率对插入损耗、最大衰减量、工作范围的影响 ,以及F P腔腔长与衰减量之间的关系 ,分析了这种衰减器的带宽响应。衰减器体积只有 2 0 0× 2 0 0× 30 0 μm左右 ,插入损耗小于 2dB ,最大衰减量为 44dB左右。     

Polarization splitting filter characteristics of Au-filled high-birefringence photonic crystal fiber

Polarization splitting wavelength-selective characteristics of Au-filled high-birefringence photonic crystal fiber (HB-PCF) based on the finite element method is investigated. Numerical results show that the polarization splitting effect can be observed in metal-filled HB-PCF. The resonances points and strength in two polarizations can be adjusted by changing the fiber birefringence, the pitch between the adjacent air holes and the size of the metal wires. Finally, two kinds of Au-filled HB-PCFs with completely polarization splitting and filtering characteristics in communication wavelength are designed. Results show that this polarization splitting effect in metal-filled HB-PCF is very useful for further studies in polarization-dependent wavelength-selective applications and other fiber-based plasmonic devices.