Ce0.1+xTi0.5-xAl0.2Y0.1La0.1O1.8材料的制备及在三效催化剂中的应用

采用共沉淀法制备了Ce0.1+xTi0.5-xAl0.2Y0.1La0.1O1.8(0≤x≤0.4)材料, 并对所制备的材料进行了X射线衍射(XRD)和X射线光电子能谱(XPS)的表征, 测定了材料的比表面积(BET法)和储氧量(OSC), 同时采用氢气程序升温还原(H2-TPR)和氨气程序升温脱附(NH3-TPD)研究了材料的还原性能和表面酸性. 研究结果表明, Ce/Ti摩尔比大于1∶2的材料能形成立方萤石结构的固溶体, Ce/Ti摩尔比为1时, 材料表面Ce4+/Ce3+摩尔比达到最大; 随着Ce/Ti摩尔比的增大, 材料的储氧能力先增大后减小, 而TPR还原峰温则是先减小后增大, 当Ce/Ti摩尔比为1时, 材料的储氧量达到最大, 为660 μmol/g; 还原峰峰温最低, 为616 ℃. 以制备的材料为载体制备了一系列Pt/Ce0.1+xTi0.5-xAl0.2Y0.1La0.1O1.8三效催化剂, 并对催化剂进行了活性评价. 活性测试结果表明, 以Ce/Ti比为1的载体材料制成的催化剂对C3H8, CO和NO的起燃温度分别为236, 147和228 ℃, 表现出了优异的温度特性.     

BaCe0.8Zro.1La0.1O3-α陶瓷的制备和电性能研究

以高温固相反应法制备了BaCe0.gZr0.1Lao1O3-α陶瓷,用粉末X-射线衍射(XRD)和扫描电镜(SEM)对其晶体结构和断面形貌进行了表征.以陶瓷材料为固体电解质、多孔性铂为电极,用交流阻抗谱技术测定了材料在500～900℃下不同气体气氛中的电导率;用气体浓差电池方法测定了材料在于燥空气和湿润空气中的离子迁移...     

大孔高镍LiNi0.8Co0.1Mn0.1O2正极材料的制备及其电化学性能研究

本工作以聚甲基丙烯酸甲酯(PMMA)微球组装成的胶晶模板作为铸模,溶胶-凝胶法辅助获得大孔LiNi0.8Co0.1Mn0.1O2 (NCM811)正极材料.结果 表明,利用PMMA作为造孔剂,形成了由100nm的颗粒堆积而成的大孔结构,这种结构有效地提高了材料的倍率性能和循环稳定性.大孔NCM811在0.1C的首次放电...     

Surface modification of LiNi0.8Co0.1Mn0.1O2 with conducting polypyrrole

A facile method for the surface modification of high-voltage and high-temperature LiNi_0.8Co_0.1Mn_0.1O₂ cathode materials is demonstrated. In order to prepare polypyrrole (PPy) coating LiNi_0.8Co_0.1Mn_0.1O₂ material, the facile chemical polymerization method uses Fe(III) tosylate as oxidant and ethanol as solvent to avoid the side reaction with solvent. TEM depicts that LiNi_0.8Co_0.1Mn_0.1O₂ serves as hard template and the nanoscale PPy layer grows along the surface of LiNi_0.8Co_0.1Mn_0.1O₂ during the synthesis process. Because of flocculent and nanofiber coating layer, much improved rate performance, high temperature cycling, as well as high voltage performance are obtained. Cyclic voltammetry (CV) and electrochemical impedance spectroscopic (EIS) results demonstrate that the PPy coating layer effectively alleviates the side reactions between liquid electrolytes and LiNi_0.8Co_0.1Mn_0.1O₂ surface that are highly unstable at high temperature and high charge voltage.     

Na-doped layered LiNi0.8Co0.1Mn0.1O2 with improved rate capability and cycling stability

Journal of Solid State Electrochemistry - We have prepared LiNi0.8Co0.1Mn0.1O2 (LNMCO) doped with Na+ and studied its properties using X-ray diffraction (XRD), energy dispersive X-ray analysis...     

Complementary dual-doping of LiNi0.8Co0.1Mn0.1O2 cathode enhances ion-diffusion and stability for Li-ion batteries

The Ni-rich LiNi_0.8Co_0.1Mn_0.1O₂ (NCM811) layered cathodes endow Li-ion batteries (LIBs) with high energy density. However, they usually suffer from limited ion-diffusion and structural instability during cycling. Although doping strategy can effectively alleviate these issues, the coupling effects of multi-element doping and the corresponding performance enhancement mechanism have been yet unclear. Here, we report a Zr/Ti dual-doped NCM811 cathode material (ZT-NCM811), in which Zr-ion is doped into both transition metal (TM) layers and lithium layers and Ti-ion is only distributed in TM layers. The dual-doping can effectively enhance crystal structure stability via inhibiting the lattice collapse along c-axis and decreasing the Li/Ni disorder. Meantime, the lattice oxygen escape is also greatly reduced due to the presence of stronger Zr-O and Ti-O bonds, further mitigating the crystal surface parasitic reactions with electrolyte. The resultant ZT-NCM811 exhibits high specific capacity of 124 mAh/g at even 10 C, much higher than undoped and single-doped NCM811, and a retention of 98.8% at 1 C after 100 cycles. The assembled ZT-NCM811/graphite full cell also delivers superior battery performances and durability.     

Calorimetric Study of Interaction in the Systems LaNi4.9Al0.1-H2 and LaNi4.9Sn0.1-H2

Interaction of hydrogen with the intermetallic compounds LaNi4.9Al0.1 and LaNi4.9Sn0.1 was studied by Tian-Calvet differential heat-conducting microcalorimetry. In the range 308-353 K these com- pounds exhibit a low equilibrium hydrogen pressure in the region of the plateau, a fairly high absorption capacity, and an insigificant hysteresis of the absorption/desorption pressures in the two-phase region of the P-C-T diagram. The enthalpies of hydrogenation of the intermetallic compounds were calculated from the results of the calorimetric experiment and by the van't Hoff equation; the entropies and Gibbs free energies of hydrogenation in the range 308-353 K were calculated. The probable mechanism of the interaction of hydrogen with the intermetallic compounds was suggested.     

Improvement of electrochemical performance of LiNi0.8Co0.1Mn0.1O2 cathode material via Li2.09W0.9Nb0.1O4 Li-ion conductive coating layer

Journal of Solid State Electrochemistry - Recently, niobium tungsten oxide has garnered considerable attention owing to its excellent Li-ion diffusion rate and prominent structural stability during...     

Enhanced electrochemical performance of LiNi0.8Co0.1Mn0.1O2 cathode via dual-functional lanthanide modification

Journal of Solid State Electrochemistry - This study investigates the use of lanthanide elements to modify a layered oxide cathode through solid-state calcination. Based on the findings, the...     

Enhanced electrochemical performance of LiNi0.8Co0.1Mn0.1O2 cathode via wet-chemical coating of MgO

Journal of Solid State Electrochemistry - LiNi0.8Co0.1Mn0.1O2 (NCM811) has a high potential for using as the cathode material for lithium–ion batteries (LIBs) for electric vehicles owing to...     

Ni添加对Ti0.4Zr0.1V1.1Mn0.5Cr0.1合金的相结构和电化学性能的影响

本文通过XRD、SEM、EDS研究了Ti0.4Zr0.1V1.1Mn0.5Cr0.1Nix(x=0,0.2,0.4,0.6,0.8)合金的相结构和电化学性能.该合金系由BCC结构的V基固溶体主相和六方结构的C14 Laves第二相组成,Ni能够促进第二相的生成,Ni含量的增加导致了各相中的化学组成和晶格参数的变化,并通过电化学方法研究了Ni含量对Ti0.4Zr0.1V1.1Mn0.5Cr0.1合金电极的最大放电容量、自放电性能、高倍率放电性能、循环稳定性能等的影响.     

Growth and characterization of 0.1 and 0.25 zinc magnesium ammonium sulphate

Mixed crystals of 0.1 and 0.25 zinc magnesium ammonium sulphate were grown by slow evaporation of aqueous solution at room temperature. The bright and transparent crystals obtained were characterized by thermal (TG–DTA), FTIR and XRD analyses. A fitting decomposition pattern for the compound was formulated on the TG curve which shows two stage mass losses between 133 and 478.75 °C. In this temperature range, DTA curve shows exothermic peaks supporting the formulated decomposition pattern. The FTIR spectra show the vibration frequencies due to the formation of zinc magnesium ammonium sulphate mixed crystals. Detailed structural analysis of the compound is under progress.     

Synthesis and electrocatalytic performance of La0.3Ce0.1Sr0.5Ba0.1TiO3 anode catalyst for solid oxide fuel cells

Ce-doped La_0.4Sr_0.5Ba_0.1TiO_3–δ (LCSBT) perovskite anode catalysts in solid oxide fuel cells were successfully synthesized by a modified rheological phase reaction for the first time. Pure LCSBT could be obtained under a reducing atmosphere and nano-CeO₂ particles could be exsoluted from LCSBT after being sintered in air. The catalytic activity and electrochemical performance of LCSBT anodes for the H₂ oxidation were obviously improved comparing with the pure La_0.4Sr_0.5Ba_0.1TiO_3–δ (LSBT) and LSBT&CeO₂ admixture anodes. The improved performance could be attributed to the nanostructure of LCSBT and the exsoluted nano-CeO₂ particles.     

Atom probe tomographic studies of precipitation in Al-0.1Zr-0.1Ti (at.%) alloys.

Atom probe tomography was utilized to measure directly the chemical compositions of Al(3)(Zr(1)-(x)Ti(x)) precipitates with a metastable L1(2) structure formed in Al-0.1Zr-0.1Ti (at.%) alloys upon aging at 375 degrees C or 425 degrees C. The alloys exhibit an inhomogeneous distribution of Al(3)(Zr(1)-(x)Ti(x)) precipitates, as a result of a nonuniform dendritic distribution of solute atoms after casting. At these aging temperatures, the Zr:Ti atomic ratio in the precipitates is about 10 and 5, respectively, indicating that Ti remains mainly in solid solution rather than partitioning to the Al(3)(Zr(1)-(x)Ti(x)) precipitates. This is interpreted as being due to the very small diffusivity of Ti in alpha-Al, consistent with prior studies on Al-Sc-Ti and Al-Sc-Zr alloys, where the slower diffusing Zr and Ti atoms make up a small fraction of the Al(3)(Zr(1)-(x)Ti(x)) precipitates. Unlike those alloys, however, the present Al-Zr-Ti alloys exhibit no interfacial segregation of Ti at the matrix/precipitate heterophase interface, a result that may be affected by a significant disparity in the evaporation fields of the alpha-Al matrix and Al(3)(Zr(1)-(x)Ti(x)) precipitates and/or a lack of local thermodynamic equilibrium at the interface.     

电/离子导体双包覆的LiNi0.8Co0.1Mn0.1O2锂离子电池阴极材料及其电化学性能

高镍三元材料LiNi_0.8Co_0.1Mn_0.1O₂ (NCM)比容量高且成本低, 但材料结构在电化学循环过程中的不稳定性影响了其大规模的应用, 可采用表面包覆的策略来改善材料的结构稳定性, 从而提高其电化学性能. 本工作结合高速固相包覆法和高温烧结法, 分别将电子导体氧化锡锑(ATO)和锂离子导体偏磷酸锂(LOP)共同包覆在NCM材料表面. 双包覆后的NCM材料的电子电导率从2.17×10^-3 Ѕ•cm^-1提高至1.02×10^-2 Ѕ•cm^-1, 锂离子扩散系数也从7.05×10^-9 cm²•s^-1提高至2.88×10^-8 cm²•s^-1. 同时, NCM表面的双包覆层可以在循环过程中阻止电极材料与电解液发生氧化还原反应, 抑制材料不利相变, 减少氧的析出, 稳定材料结构. 电化学性能测试表明, 经过表面包覆后, NCM材料在1 C (180 mA•g^-1)的电流下和2.7~4.3 V (vs. Li/Li⁺)的电压范围内, 循环150周后容量为161.1 mAh•g^-1, 保持率为87.1%, 而在10 C的充放电倍率下具有133 mAh•g^-1的可逆比容量.     

Effect of lower cut-off voltage on LiNi0.8Co0.1Mn0.1O2/graphite–SiOx pouch battery

Journal of Solid State Electrochemistry - Long-term cycle life and high safety are important performances of lithium-ion power batteries. Voltage windows have a significant impact on battery cycle...     

Mg0.9-xTi0.1PdxNi(x=O.04～0.1)贮氢合金电极腐蚀行为研究

研究了Pd部分替代Mg对Mg0.9-xTi0.1PdxNi(x=0.04～0.1)贮氢合金腐蚀性能的影响.利用机械合金化方法制备了Mg0.9-xTi0.1PdxNi(x=0.04～0.1)贮氢合金.XRD和TEM分析表明经120 h球磨后该合金完全非晶化.循环充放电测试结果表明,Pd的替代有效地延长了Mg0.9-xTi0.1PdxNi(x=0.04～0.1)合金的循环寿命.采用开路电位测量,阳极极化,电化学阻抗和X射线光电子能谱研究了该合金的腐蚀行为.结果表明,随着Pd含量增加,合金腐蚀电位正移,初始腐蚀电流下降,腐蚀电流增加的速度变缓.采用本文提出的等效电路模型较好地拟合了合金的电化学阻抗谱.分析表明,随着Pd含量的增加,合金表面钝化膜厚度和电阻逐渐增大.X射线光电子能谱分析表明,Pd的加入减弱了合金在充放电过程中的氧化程度.当Pd含量达到0.1时,Mg0.9-xTi0.1PdxNi(x=0.04～0.1)合金的耐腐蚀性能最好,其放电容量保持率最高.     

Ti/Ru0.1Ti0.1Sn0.8O2电极电容性能研究

低温热分解法制备Ti/Ru0.1Ti0.1Sn0.8O2.XRD表征该样品结构特性,循环伏安和恒流充放电测定电极性能.结果表明,Ti/Ru0.1Ti0.1Sn0.8O2物相属细小的金红石相,在20 mV/s扫速下该电极比电容达933F/g.1000次充放电循环后,比电容衰减23.6﹪,显示良好的循环稳定性和可逆性.     

四元Mg0.9Ti0.1Ni0.9X0.1(X=Mn,Zn,Co,Fe)系列合金的制备及性能研究

用机械合金化法合成了Mg0·9Ti0·1Ni0·9X0·1(X=Mn,Zn,Co,Fe)系列合金.X射线衍射(XRD)结构分析表明,用X部分替代Ni后,促进了Mg0·9Ti0·1Ni合金的非晶化过程.用Co和Fe部分替代Ni提高了合金的放电容量,但却降低了合金的循环稳定性.用Zn和Mn部分替代Ni提高了合金电极的循环寿命,尤其是Mg0·9Ti0·1Ni0·9Zn0·1合金电极经10个充放电循环后,其放电容量仍可达到313·8mA·h/g.对添加Co后的合金进行p-c-T测试发现,Mg0·9Ti0·1Ni0·9Co0·1合金的吸放氢容量明显比Mg0·9Ti0·1Ni合金高,这与电化学所测到的结果一致.     

贮氢电极合金ZrCr_(0.4)Mn_(0.2)V_(0.1)Co_(0.1)Ni_(1.2)高温电化学性能的研究

研究了AB2型Laves相贮氢电极合金ZrCr0.4Mn0.2V0.1Co0.1Ni1.2在不同温度下的放电容量、活化、高倍率和自放电等电化学性能.实验表明:25℃下,合金电极经13次循环后其最大放电容量为336mAh/g,在70℃下,仅需4次循环就达到298mAh/g;该合金在70℃,300mA/g电流下的高倍率放电性能比25℃时提高了约16%,但自放电性能却从3%/d下降到17%/d,虽然温度升高,合金的循环性能有所下降,但还是相当稳定的.这主要是因为循环过程中合金表面形成的氧化膜阻碍了合金元素进一步溶解造成的.