Adsorption of small molecules on a (2 × 1) PdZn surface alloy on Pd(1 1 1)

The adsorption of methanol, formaldehyde, methoxy, carbon monoxide and water on a (2 × 1) PdZn surface alloy on Pd(1 1 1) has been studied using DFT calculations. The most stable adsorption structures of all species have been investigated with respect to the structure and the electronic properties. It was found that methanol is only weakly bound to the surface. The adsorption energy only increases with higher methanol coverage, where chain structures with hydrogen bonds between the methanol molecules are formed. The highest adsorption energy was found for the formate species followed by the methoxy species. The formaldehyde species shows quite some electronic interaction with the surface, however the stable η₂ formaldehyde has only an adsorption energy of about 0.49 eV. The calculated IR spectra of the different species fit quite well to the experimental values available in the literature.     

Interaction of Ag with the Si(1 1 1)1 × 1–H surface

Synchrotron radiation based photoemission spectroscopy (SRPES) and low energy electron diffraction (LEED) are used to study the interaction between Ag atoms and the Si(1 1 1)1 × 1–H surface. At an Ag coverage of 0.063 monolayers (ML) on the Si(1 1 1)1 × 1–H surface, the Si 2p component corresponding to Si–H bonds decreases, and an additional Si 2p component appears which shifts to a lower binding energy by 109 meV with respect to the Si bulk peak. The new Si 2p component is also observed for 0.25 ML Ag on the Si(1 1 1)7 × 7 surface. These findings suggest that Ag atoms replace the H atoms of the Si(1 1 1)1 × 1–H surface and form direct Ag–Si bonds. Contrary to the widely accepted view that there is no chemical interaction between Ag particles and the H-passivated Si surface, these results are in good agreement with recent first-principles calculations.     

ICLAS of water in the 770 nm transparency window (12 746–13 558 cm−1). Comparison with current experimental and calculated databases

The absorption spectrum of water vapor has been investigated by intracavity laser spectroscopy (ICLAS) in the 12 746–13 558 cm^?1 spectral region corresponding to an interesting transparency window of the atmosphere, partly obscured by the A band of molecular oxygen.The achieved sensitivity—in the order of α_min～10^?9 cm^?1—has allowed one to measure 1062 water lines with intensities ranging from 1.6×10^?28 to 2.35×10^?24 cm/molecule at 296 K. A total of 169 new and improved energy levels belonging to 21 vibrational states could be determined from 374 newly measured transitions. The retrieved experimental line list is compared with the spectra calculated by Schwenke and Partridge, and Barber and Tennyson. Comparison with the available experimental databases shows that the obtained results represent a significant improvement of the knowledge of the water absorption in the considered region, in particular in the region of the oxygen A band.     

Calculation of electronic and optical properties of zinc blende GaP1 − xNx

In order to clarify the electronic properties of the ternary compound semiconductor GaPN, in a zinc-blende structure, a simple pseudopotential scheme (EPM), within an effective potential (VCA), is proposed. The effects of disorder and spin–orbit coupling are neglected. Various quantities, such as energy levels, charge densities, ionicity character, transverse effective charge, and refractive index are obtained for this alloy. Moreover, the crossover of the direct and indirect band gaps is predicted.     

Adsorption behaviors of CO on W(1 1 0) and Mo(1 1 0) surfaces in the β-state are still not clear

Adsorption structure of CO on W and Mo at above ～800 K (β-CO) has been extensively studied in the history of surface science. Most of the previous studies concluded that CO is dissociated in the β-CO, and a tilted structure plays a role as a precursor state of the dissociation. We have recently studied valence band spectra of the β-CO on W(1 1 0), oxygen-precovered W(1 1 0) and Mo(1 1 0) using synchrotron radiation. CO-derived states with binding energies close to those of the 4σ-CO can be observed, implying a non-dissociative chemisorption in this high-temperature state. We suggest that still some additional works need to be done in order to understand adsorption structure of β-CO completely.     

Selective adsorption of coronene on Si(1 1 1)-(7 × 7)

The adsorption of coronene (C₂₄H₁₂) on the Si(1 1 1)-(7 × 7) surface is studied using scanning tunneling microscopy (STM). Upon room temperature submonolayer deposition, we find that the coronene molecules preferentially adsorb on the unfaulted half of the 7 × 7 unit cell. Molecules adsorbed on different sites can be induced to move to the preferential sites by the action of the tip in repeated image scans. Imaging of the molecules is strongly bias dependent, and also critically depends on the adsorption site. We analyze the results in terms of differential bonding strength for the different adsorption sites and we identify those substrate atoms which participate in the bonding with the molecule.     

Nonlinear optical properties of CdxZn1 − xO films deposited with PLD technique

In this paper, the structural and optical properties of Cd_xZn_1 ? xO films were studied. The films were deposited with pulse laser deposition (PLD) technique. The Cd concentration changed in the range from x = 0 to 0.2. The structure of the films was characterized by atom force microscope (AFM) and X-ray diffraction (XRD). The nonlinear optical properties were investigated by Z-scan methods. The two-photon absorption (TPA) coefficient β_eff was measured. The β_eff value changes from 49.2 cm/GW to 116.5 cm/GW with the Cd concentration from 0 to 15%.     

Atomic and nanostructures of monolayer c(2 × 2)NiN on Cu(0 0 1)

Structures of monolayer nickel nitride (NiN) on Cu(0 0 1) surface are studied by X-ray photoelectron spectroscopy (XPS), low energy electron diffraction (LEED) and scanning tunneling microscopy (STM). Formations of Ni–N chemical bonds and NiN monolayer at the surface are confirmed by XPS on the N-adsorbed Cu(0 0 1) surfaces after Ni deposition and subsequent annealing to 670 K. A c(2 × 2) structure is always observed in the LEED patterns, which is a quite contrast to the (2 × 2)p4g structure observed usually at the N-adsorbed Ni(0 0 1) surface. Atomic images by STM indicate the mixture of Ni–N and Cu–N structures at the surface. Density of the trenches on the N-saturated surface decreases and the grid pattern on partially N-covered surfaces becomes disordered with increasing the Ni coverage. These results are attributed to the decrease of the surface compressive stress at the N-adsorbed Cu surface by mixing Ni atoms.     

Pressure and compositional dependence of electric conductivity in the (Mg1 − xFex)1 − δO (x = 0.01–0.40) solid-solution

(Mg_1 ? xFe_x)_1 ? δO (x = 0.01–0.43) single crystals (~ 8 mm in diameter) were made by a melt-growth method. Electrical conductivity measurements were carried out as functions of temperature and frequency by a complex impedance method under pressure (~ 43 GPa and ~ 673 K and at 0.1 MPa and ~ 1400 K). Our experimental results show a change in charge transport mechanism in the (Mg_1 ? xFe_x)_1 ? δO solid solution at high temperature. The temperature of inflection point of the slope in Arrhenius plots depend greatly on both composition and extrinsic factors of crystals. The low-temperature conduction mechanism in (Mg_1 ? xFe_x)_1 ? δO solid solution is small polaron. Pressure effect of the electric conductivity was observed and the conductivity increased to 0.5 at log scale of S/m with increasing pressure up to 43.4 GPa. The activation energy was decreased linearly with increasing pressure. Chemical composition and homogeneity of specimen rather than pressure greatly influence the electric conductivity. The activation energy of 2.37(4) eV for the (Mg_0.99Fe_0.01)_1 ? δO solid solution might correspond to a migration enthalpy of O ions through thermally formed defects. It is proposed that a possible dominant electrical conduction mechanism in ferropericlase under the lower mantle conditions, at least in the higher temperature region, is super ionic conduction.     

Structural,optical and electrical properties of undoped and Si-doped AlxGa1−xN thin films on Si (1 1 1) substrate grown by PA-MBE

We have studied the structural properties of undoped and Si-doped Al_xGa_1?xN/GaN/AlN on Si (1 1 1) substrate prepared by plasma-assisted molecular beam epitaxy (PA-MBE) using high-resolution X-ray diffraction (HR-XRD) and atomic force microscopy (AFM). In comparison with undoped AlGaN, the roughness and dislocation density on the surface of the AlGaN layer decrease with Si doping. Full width half maximum (FWHM) of the undoped and Si-doped samples were equal to 0.69° and 0.52°, respectively. This indicates that the Si doping improves the crystalline quality of the Al_xGa_1?xN layer compared with the undoped one. Raman scattering measurement reveals that the optical phonon modes of A₁(LO) and E₂(H) of the AlGaN show a one-mode and two-modes behavior, respectively. The Fourier-transform infrared reflectance (FTIR) investigation confirms the one-mode (two-mode) behavior of the LO (TO) phonon in our samples. This is in good agreement with Raman measurement. Finally, the barrier height (Φ_B) of undoped and Si-doped Al_xGa_1?xN samples was found to be 0.86 and 0.74 eV, respectively.     

Calculation of the optical and electronic properties of the zinc-blende alloy Zn1 − xMgxSe

In order to clarify the electronic and optical properties of wide-energy gap zinc-blende structures ZnSe, MgSe and their alloys (ZnSe)_1 − x(MgSe)_x, a simple pseudo-potential scheme (EPM) within an effective potential, the virtual crystal approximation (VCA) which incorporates compositional disorder as an effective potential, is presented. Various quantities, including the fundamental band gap, the energies of several optical gaps, charge densities, ionicity character, transverse effective charge, and refractive index are obtained for this alloy.     

Performance evaluation of 64 × 10 Gbps and 96 × 10 Gbps DWDM system with hybrid optical amplifier for different modulation formats

In this paper, we investigated the performance of multi terabits DWDM system consisting of hybrid optical amplifier RAMAN-EDFA for different data format such as non-return to zero (NRZ), return to zero (RZ) and differential phase shift keying (DPSK). We find that in 64 × 10 and 96 × 10 Gbps, RZ is more adversely affected by nonlinearities, where as NRZ and DPSK is more affected by dispersion. We further show that RZ provide good quality factor (13.88 dB and 15.93 dB for 64 and 96 channels), less eye closure (2.609 dB and 3.191 dB for 64 and 96 channels) and acceptable bit error rate (3.89 × 10⁸ and 1.24 × 10⁹ for 64 and 96 channels) at the respective distance as compare to other existing modulation format. We further investigated the maximum single span distance covered by using existing data formats.     

H adsorption at Ag/Si interfaces in epitaxially grown Ag(1 1 1) films on Si(1 1 1)7 × 7 substrates

The interaction of atomic H with Ag(1 1 1)/Si(1 1 1)7 × 7 surfaces was studied by thermal desorption (TD) spectroscopy and scanning tunneling microscopy (STM) at room temperature. TD spectroscopy revealed an intense peak from mono H–Si bonds, even though the Si surface was covered by the Ag atoms. This peak was not observed from Ag-coated SiO₂/Si substrates. STM observation showed no clear change of the Ag surface morphology resulting from H exposure. All these results indicate that the atomic H adsorbs at neither the Ag surfaces nor Ag bulk sites, but at the Ag/Si interface by diffusing through the Ag film.     

Strained c(4 × 2) CoO(1 0 0)-like monolayer on Pd(1 0 0): Experiment and theory

We report on an interface-stabilized strained c(4 × 2) phase formed by cobalt oxide on Pd(1 0 0). The structural details and electronic properties of this oxide monolayer are elucidated by combination of scanning tunneling microscopy data, high resolution electron energy loss spectroscopy measurements and density functional theory. The c(4 × 2) periodicity is shown to arise from a rhombic array of Co vacancies, which form in a pseudomorphic CoO(1 0 0) monolayer to partially compensate for the compressive strain associated with the large lattice mismatch (～9.5%) between cobalt monoxide and the substrate. Deviation from the perfect 1:1 stoichiometry thus appears to offer a common and stable mechanism for strain release in Pd(1 0 0) supported monolayers of transition metal rocksalt monoxides of the first transition series, as very similar metal-deficient c(4 × 2) structures have been previously found for nickel and manganese oxides on the same substrate.     

Structural and optical properties of a catalyst-free GaAs/AlGaAs core–shell nano/microwire grown on (1 1 1)Si substrate

Heterostructure in the catalyst-free GaAs nanowire grown on the Si substrate was studied for the application of optical devices in the next generation. We fabricated AlGaAs/GaAs/AlGaAs quantum well (QW) structure on the side facet of the catalyst-free GaAs nanowire grown by molecular beam epitaxy (MBE). The cathode luminescence (CL) measurement showed that the uniform GaAs quantum well was formed between AlGaAs shell layers. On the basis of this structure, we also grew the thick AlGaAs shell layers (∼700 nm) on GaAs nanowires, and observed whispering gallery mode (WGM) resonant in the thick AlGaAs hexagonal structure.     

First principles total energy calculations of the adsorption of germane and digermane on Si(0 0 1)-c(2 × 4)

First principles total energy studies are performed to investigate the energetics, and the atomic structure of the adsorption of germane (GeH₄), and digermane (Ge₂H₆) on the Si(0 0 1)-c(2 × 4) surface. It has been observed experimentally that adsorption of Ge₂H₆ is a dissociative process, which first yields GeH₃ and then GeH₂ fragments as products. We first study the adsorption of GeH₂ considering two different models; the intra-row and the on-dimer geometries. Our results show that the on-dimer site is more stable than the intra-row geometry by 0.44 eV. This is not a surprise since in the absence of H atoms, adsorption in the on-dimer site leaves no dangling bonds. In contrast, when the GeH₂ fragment is considered together with two H atoms, the intra-row geometry is favored energetically as compared with the on-dimer site, in good agreement with experiment. Similar results have been previously obtained for the adsorption of SiH₂ on Si(0 0 1). Digermane adsorption is explored according to two different geometries. In the first one, we have considered the adsorption as two GeH₃ fragments, while in the second, we have considered the adsorption as two GeH₂ fragments plus 2 H fragments. In good agreement with experiments, it is found that the latter geometry is energetically more favorable.     

Room-temperature chemisorption of chloroethylenes on Si(1 1 1)7 × 7: formation of surface vinyl,vinylidene and their chlorinated derivatives

Chemisorption of a family of six chloroethylenes (C₂H₃Cl, 1,1-C₂H₂Cl₂, cis-1,2-C₂H₂Cl₂, trans-1,2-C₂H₂Cl₂, C₂HCl₃, and C₂Cl₄) on Si(1 1 1)7 × 7 at room temperature (RT) has been investigated by vibrational electron energy loss spectroscopy (EELS). The characteristic vibrational EELS features have been used to identify the prominent surface species upon RT adsorption. Like ethylene, C₂H₃Cl has been found to predominantly adsorb in a di-σ bonding geometry to the Si surface, while 1,1-C₂H₂Cl₂, cis- and trans-1,2-C₂H₂Cl₂, C₂HCl₃ and, to a lesser extent, C₂Cl₄ appear to undergo dechlorination upon adsorption to form chlorinated vinyl adspecies involving single-σ bonding structures. Evidence of vinylidene (>CCH₂) has been obtained for the first time on a semiconductor surface for the adsorption of 1,1-C₂H₂Cl₂. The present work illustrates that the molecular structure and the Cl content of chloroethylenes play a crucial role in controlling not only the adsorption geometry but also the extent of dechlorination and the resulting adspecies upon RT adsorption on Si(1 1 1).     

Scanning tunneling microscopy imaging of NiO(100)(1 × 1) islands embedded in Ag(100)

The imaging of NiO(100)(1 × 1) islands embedded in Ag(100) by scanning tunneling microscopy is addressed. As a function of tunneling conditions and tip termination it is possible to resolve the NiO–vacuum interface, the second oxide layer as well as the NiO-substrate interface with atomic contrast. We find that for sub-monolayer coverages of NiO the oxide islands consist of an essentially defect-free surface layer at the vacuum interface with a number of NiO second layer patches incorporated into the Ag substrate underneath. The oxide layer is surrounded by a rim of a NiO bilayer of monoatomic width. A reduction of the density of states between a NiO monolayer and local NiO bilayer stackings is suggested to be responsible for the observed appearance of mosaic patches at the island surface.