Uncertainty estimation to evaluate mass balances on a combustion system

Mass balances of ash and potassium for a fluidized bed combustor were performed incorporating measurement uncertainties. The total output mass of ash or a chemical element should be equal to the mass in the input fuel; however, this is not often achieved. A realistic estimation of recovery uncertainty can support the reliability of a mass balance. Estimation of uncertainty helps to establish a reliable evaluation of the recovery ratio of ash mass and elemental mass. This may clarify whether any apparent lack in closing the mass balance can be attributed to uncertainties. The evaluation of measurement uncertainty for different matrices, namely coal, biomass, sand and ashes from different streams was based on internal quality control data and external quality control data, namely analysis of samples from proficiency tests or use of a certified reference material. The evaluation of intermediate precision and trueness allowed the estimation of measurement uncertainty. Due to the different physic and chemical characteristics of the studied matrices, the uncertainty of precision was evaluated using R-charts of data obtained from the analysis of duplicates for the majority of samples. This allowed evaluating sample heterogeneity effects. The instrumental acceptance criterion was also considered and included in the combined uncertainty. The trueness was evaluated using data from several proficiency tests and from analysis of a certified reference material or sample spiking. Statistically significant bias was included.     

Towards standardization of external quality assessment schemes by using bias values based on biological variation

The precision and trueness of current instruments and methods in clinical laboratories is much better than in the past. However, the z-score and other comparison variables that are currently used in external quality assessment programs are based on relative data. Thus, they may change from program to program and also change over time within the same program and consequently may not be useful or cost-effective. We therefore devised a test-specific decision limit for accepting or rejecting test results based on a combination of the data of within- and between-subject biological variations. We then applied these limits to a group of tests performed in our laboratory and compared our results with those of external quality assessment programs. In addition, we combined external and internal quality control data on the same graph and prepared a two-dimensional graph for different levels of control sera. Inspection of all results of control sera on this new graph was more useful for decision making. We concluded that the z-score is not reliable for comparisons of test results in external quality assessment. As a substitute for this currently accepted practice, we assert that control limits based on biological variation are more reliable, and can be useful in the evaluation of both external and internal quality assessments and their combination on this new graph.     

Improved accuracy for the analysis of soft magnetic alloys by inductively-coupled plasma atomic emission spectrometry by using advanced standardization procedures

The applicability of simultaneous ICP-OES for the accurate analysis of soft magnetic alloys has been investigated. Long-time signal variations of up to 40% can be observed under normal operating conditions. The scattering of the values can largely be compensated by a correction procedure with internal and external standardization where the intensity value of the analytical signal is first rationed to the simultaneously measured intensity of an internal standard line and after that recalibrated with an external standard. Not only the trueness but also the precision could be improved by using Cd as a real-time internal standard. This is attributed to a compensation for instrumental fluctuations as a result of the simultaneous measurement of both emission signals.     

Improved accuracy for the analysis of soft magnetic alloys by inductively-coupled plasma atomic emission spectrometry by using advanced standardization procedures

The applicability of simultaneous ICP-OES for the accurate analysis of soft magnetic alloys has been investigated. Long-time signal variations of up to 40% can be observed under normal operating conditions. The scattering of the values can largely be compensated by a correction procedure with internal and external standardization where the intensity value of the analytical signal is first rationed to the simultaneously measured intensity of an internal standard line and after that recalibrated with an external standard. Not only the trueness but also the precision could be improved by using Cd as a real-time internal standard. This is attributed to a compensation for instrumental fluctuations as a result of the simultaneous measurement of both emission signals.     

Effectiveness of a short training session for improving pipetting accuracy

The quality of diagnostic tests conducted by the Animal Quarantine Service (AQS) is critical to the safety of national livestock production. In procedures for tests such as polymerase chain reaction and enzyme-linked immunosorbent assay, measurement of tiny quantities of samples or reagents is quite common. Therefore, many efforts have been made to maintain the quality of micropipette operations, including routine calibration of equipment and training programs for operators. In this study, we developed a pilot training program to analyze the effects of training on pipetting accuracy, i.e., trueness and precision. The program involved a self-instruction A4-sized leaflet describing how to improve pipetting technique. Thirty-three staff members from seven AQS laboratories participated in the program. Each participant repeated sampling of 300 μL of distilled water 10 times before and after reading the leaflet, and the effects of training on the trueness and precision of the pipetting results were analyzed. To determine pipetting trueness, we examined the variation of the delivered volume from the target volume (300 μL) using the proportional odds mixture model. Our data demonstrated that participation in the training program and the level of experience with pipetting significantly improved trueness. Analysis of standard deviations of the ten samplings, as an indicator of precision, also showed that participation in the training program improves pipetting precision. Thus, our data supported the implementation of such simple, quick training sessions to improve pipetting trueness and precision in diagnostic laboratories.     

Many years of experiences in internal quality control in the toxicological analysis of biological material in the field of occupational medicine

Summary Toxicological analysis in blood and urine for biological monitoring of occupationally exposed persons must be carried out in the Federal Republic of Germany under an internal and external quality control scheme. The results of many years of experiences with 5 commercially available control specimens (1 blood, 1 serum, 3 urine samples) from three companies for internal quality assurance are presented. Precision and accuracy were evaluated by comparison of our results with the data of the initial period (within day precision of the methods) and the assigned values. Over years the commercially available control specimens show good comparable results. Except in a few cases, there was a good agreement between our results and the assigned values. An expected worldwide increase of the importance of biological monitoring makes the availability of control specimens for everyday use a prerequisite in effective internal quality control. This is especially valid for the determination of organic compounds, e.g. solvents and pesticides in blood and urine samples.     

Quantitative analysis of diclazuril in animal plasma by liquid chromatography/electrospray ionization mass spectrometry

A novel, sensitive and specific method for the quantitative determination of diclazuril in animal plasma using liquid chromatography combined with electrospray ionization tandem mass spectrometry (LC/ESI-MS/MS) with negative ion detection is presented. Extraction of the samples was performed with a rapid deproteinization step using acetonitrile. Chromatography of diclazuril and the internal standard was achieved on a Nucleosil ODS 5-microm column, using a gradient elution with 0.01 M ammonium acetate and acetonitrile. To obtain the highest sensitivity and specificity possible, the mass spectrometer was operated in the multiple reaction monitoring (MRM) mode. The method was validated according to the requirements defined by the European Community. Calibration curves using plasma fortified between 1-100 ng/mL and 100-2000 ng/mL showed good linear correlation (r >or= 0.9991, goodness-of-fit coefficient 相似文献   

The new ISO Guide 80: Guidance for the in-house preparation of quality control materials (QCMs)

Reference materials (RMs) are widely used in measurement laboratories for a variety of purposes, and it is important to recognise that the material most appropriate for a particular application should be used. Certified reference materials (CRMs) are used for method validation, the calibration of a measurement system and all other aspects of the evaluation of the measurement system where the trueness of the measurement result is required. For other aspects, such as quality control, precision studies, the checking of the variability between operators, where the results are compared relatively, any suitable reference material can be used. ISO/REMCO, the ISO Committee on Reference Materials, has prepared ISO Guide 80, a guidance document for the in-house preparation of quality control materials (QCMs). QCMs are mostly used to monitor the performance of laboratory methods that have already been validated over time to be able to detect change or when a method goes out of statistical control. QCMs are RMs and as such have to be sufficiently homogeneous and stable for the intended use. QCMs are usually prepared in-house by laboratory staff for in-house use only, and therefore, the requirements for “in-house” QCMs are less demanding than those for a CRM. For example, transport issues are not of concern. The quality assessment of QCMs should involve homogeneity and stability assessments, and a limited characterisation of the material to provide an indication of its relevant property values and their variation, prior to use.     

Application of a new AMIQAS computer program for integrated quality control, method evaluation and proficiency testing

Summary The computer program AMI - Quality Assessment Scheme (AMIQAS) was designed to give easy statistical management of analytical data in relation to method evaluation, internal quality control and proficiency testing. The program is designed in accordance with the recommendation of the ISO 5725 guideline and other official recommendations. The program consists of a database, test for outliers, statistics and graphs for evaluation of an analytical method for chemical, biological and environmental analysis, different control charts to be used in day-to-day internal quality control (Shewhart charts and z-charts). Finally the program has facilities to perform proficiency testing (also called external quality control) and produce the relevant evaluation reports for the documentation of method performance and quality control of results of measurements. The present paper demonstrates the applicability of the AMIQAS program for integrated method evaluation, internal quality control and proficiency testing using the determination of the concentration of lead in human whole blood as the numerical example.     

Nonaqueous capillary electrophoresis method for the enantiomeric purity determination of S-timolol using heptakis(2,3-di-O-methyl-6-O-sulfo)-beta-cyclodextrin: validation using the accuracy profile strategy and estimation of uncertainty

Nonaqueous capillary electrophoresis (NACE) was successfully applied to the enantiomeric purity determination of S-timolol maleate using heptakis(2,3-di-O-methyl-6-O-sulfo)-beta-cyclodextrin (HDMS-beta-CD) as chiral selector. With a background electrolyte made up of a methanolic solution of 0.75 M formic acid, 30 mM potassium camphorsulfonate and containing 30 mM HDMS-beta-CD, the determination of 0.1% of R-timolol in S-timolol could be performed with an enantiomeric resolution of 8.5. Pyridoxine was selected as internal standard. The NACE method was then fully validated by applying a novel strategy using accuracy profiles. It is based on beta-expectation tolerance intervals for the total measurement error which includes trueness and intermediate precision. The uncertainty of measurements derived from beta-expectation tolerance intervals was estimated at each concentration level of the validation standards. To confirm the suitability of the developed and validated method, several real samples of S-timolol maleate containing R-timolol maleate at different concentrations were analysed and the results were compared to those obtained by liquid chromatography.     

Determination of ivermectin B(1a) in animal plasma by liquid chromatography combined with electrospray ionization mass spectrometry

A novel, sensitive and specific method for the quantitative determination of ivermectin B(1a) in animal plasma using liquid chromatography combined with positive electrospray ionization tandem mass spectrometry (LC/ESI-MS/MS) is presented. Abamectin was used as the internal standard. Extraction of the samples was performed with a deproteinization step using acetonitrile. Chromatographic separation was achieved on a Nucleosil ODS 5 microm column, using gradient elution with 0.2% (v/v) acetic acid in water and 0.2% (v/v) acetic acid in acetonitrile. The method was validated according to the requirements defined by the European Community. Calibration curves using plasma fortified between 1 and 100 ng ml(-1) showed a good linear correlation (r > or = 0.9989, goodness-of-fit coefficient < or =8.1%). The trueness at 2 and 25 ng ml(-1) (n = 6) was +4.2 and -17.1%, respectively. The trueness and between-run precision for the analysis of quality control samples at 25 ng ml(-1) was -4.0 and 11.0%, respectively (n = 16). The limit of quantification of the method was 1.0 ng ml(-1), for which the trueness and precision also fell within acceptable limits. Using a signal-to-noise ratio of 3 : 1, the limit of detection was calculated to be 0.2 ng ml(-1). The specificity was demonstrated with respect to ivermectin B(1b).The method was successfully used for the quantitative determination of ivermectin B(1a) in plasma samples from treated bovines, demonstrating the usefulness of the developed method for application in the field of pharmacokinetics.     

BCR®-701: a review of 10-years of sequential extraction analyses

A detailed quantitative analysis was performed on data presented in the literature that focused on the sequential extraction of cadmium (Cd), chromium (Cr), copper (Cu), nickel (Ni), lead (Pb) and zinc (Zn) from the certified reference material BCR-701 (lake sediment) using the three-step harmonized BCR(?) procedure. The accuracy of data reported in the literature, including precision and different measures of trueness, was assessed relative to the certified values for BCR-701. Forty data sets were accepted following extreme outlier removal, and statistically summarized with measures of central tendency, dispersion, and distribution form. In general, literature data were similar in their measurement precision to the expert laboratories used to certify the trace element contents in BCR-701. The overall median precision for literature reported data was 10% (range 6-19%), compared to certifying laboratories of 9% (range 4-33%). One measure of literature data trueness was assessed via a confirmatory approach using a robust bootstrap method. Only 22% of the comparisons indicated significantly different (all were lower) concentrations reported in the literature compared to certified values. The question of whether the differences are practically significant for environmental studies is raised. Bias was computed as a measure of trueness, and literature data were more frequently negatively biased, indicating lower concentrations reported in the literature for the six trace elements for the three-step sequential procedure compared to the certified values. However, 95% confidence intervals about the average bias for the 18 comparisons indicated only four instances when a mean bias of 0 (i.e., measured=certified) was not incorporated-suggesting statistical difference. Finally, Z-scores incorporating a Horwitz-type function were used to assess the general trueness of laboratory data. Of the 468 laboratory Z-score values computed, 92% were considered to be satisfactory, 5% were questionable, and 3% were unsatisfactory. A detailed examination of the methodology sections of the various studies showed that despite claiming adherence to the harmonized BCR sequential extraction protocol, significant deviations were commonly observed; particularly in moisture correction, sample mass, centrifugation specifics, shaking specifics, and incorporation of filtration. It is likely that failure to strictly adhere to the protocol adversely impacted accuracy, by increasing the degree of imprecision and resulting in more discrepant trueness values.     

Evaluation of measurement uncertainties for the determination of total metal content in soils by atomic absorption spectrometry

In this work estimation of measurement uncertainties associated with the total metal content in soils was done by an intralaboratory approach based on method validation and quality control data, and using two certified reference materials (CRM). CRM and soil samples were analyzed following procedures based on the methods that are applied to silicate materials. All elements were determined by atomic absorption spectrometry following a quality assurance program previously established. Quality control actions were implemented in order to provide reliable data. The precision under within-laboratory reproducibility conditions was estimated from triplicate analysis. The trueness component was determined as recovery of the analyte from CRMs: soil sample, SO-2 and river clay sediment, LGC 6139. Combined measurement uncertainty was expressed in terms of precision and recovery uncertainties and the later further split on CRM replicate analysis and uncertainty of the certified value components. The results obtained are critically discussed on the basis of the different contributions. For the selection of the reference material, the CRM dependent terms are critically compared in order to fulfill specific requirements. Electronic supplementary material  The online version of this article (doi:) contains supplementary material, which is available to authorized users.     

Analysis of pesticides and metabolites in Spanish surface waters by isotope dilution gas chromatography/mass spectrometry with previous automated solid-phase extraction Estimation of the uncertainty of the analytical results

A method based on isotope dilution gas chromatography/mass spectrometry (GC/MS) with automated solid-phase extraction (SPE) is described for the analysis of 32 pesticides and metabolites in surface waters. This approach consist in the use of nine isotopically labelled representative pesticides as internal standards, which allows high accuracy (trueness and precision) and sensitivity for most analysed compounds, as it is required for isotope dilution-based methods. Uncertainties associated with pesticide determination in real samples were estimated using quality assurance/quality control (QA/QC) data. For most pesticides expanded uncertainty was below 40%, according to the commonly established requirements for analytical results. Ninety three Spanish surface waters collected in June-July and September-November 2004 were analysed. Concentration and occurrence of pesticides were evaluated. These parameters were higher in the summer than in the autumn period. In summer four pesticides were found in more than 50% of the analysed samples and four compounds were detected above the concentration level of 1 microg/l (atrazine, terbutylazine, 3,4-dichloroaniline and fenitrothion), while in autumn percentage of detection was below 50% for all pesticides and only one compound (terbutylazine) exceeded 1 microg/l.     

Development of fully automated quantitative capillary electrophoresis with high accuracy and repeatability

A quantitative capillary electrophoresis (qCE) was developed by utilizing a rotary type of nano‐volume injector, an autosampler, and a thermostat with cooling capacity. The accuracy and precision were greatly improved compared with conventional capillary electrophoresis. The 10 nL volume accuracy was guaranteed by the carefully designed nano‐injector with an accurate internal loop. The system repeatability (precision) in terms of RSD <0.5% for migration time and 1% for peak area were achieved by using DMSO as a test sample. We believe that this fully automated qCE system has the potential to be employed broadly in quality control and quality assurance in the pharmaceutical industry. Copyright © 2015 John Wiley & Sons, Ltd.     

A quantitative solid-state Raman spectroscopic method for control of fungicides

A new analytical procedure using solid-state Raman spectroscopy within the THz-region for the quantitative determination of mixtures of different conformations of trifloxystrobin (EE, EZ, ZE and ZZ), tebuconazole (1), and propiconazole (2) as an effective method for the fungicide product quality monitoring programmes and control has been developed and validated. The obtained quantities were controlled independently by the validated hybrid HPLC electrospray ionization (ESI) tandem mass spectrometric (MS) and matrix-assisted laser desorption/ionization (MALDI) MS methods in the condensed phase. The quantitative dependences were obtained on the twenty binary mixtures of the analytes and were further tested on the three trade fungicide products, containing mixtures of trifloxystrobin-tebuconazole and trifloxystrobin-propiconazole, as an emissive concentrate or water soluble granules of the active ingredients. The present methods provided sufficient sensitivity as reflected by the metrologic quantities, evaluating the concentration limit of detection (LOD) and quantification (LOQ), linear limit (LL), measurement accuracy and precision, true quantity value, trueness of measurement and more.     

Development of a nano-liquid chromatography on chip tandem mass spectrometry method for high-sensitivity hepcidin quantitation

Microfluidic LC systems present undeniable advantages over classical LC in terms of sensitivity. Hepcidin, a peptide marker of clinical disorders linked to iron metabolism, was used as model to demonstrate peptide quantification potentialities of LC-chip coupled to a nanoelectrospray source ion trap mass spectrometer in an aqueous sample. First, stable isotope labelled hepcidin was chosen as internal standard and gradient as well as sample compositions were optimised using design of experiments as development tool. The method was then prevalidated using accuracy profiles in order to select the most appropriate response function and to confirm the ability of the technique to quantify low hepcidin concentration. A reliable and very sensitive quantitation method was finally obtained using this integrated microfluidic technology. Indeed, good results with respect to accuracy, trueness and precision were achieved, as well as a very low limit of quantitation (0.07 ng/ml). Method suitability of nano-LC on chip tandem mass spectrometry for hepcidin quantitation was also demonstrated in complex media such as human plasma.     

Intra-laboratory assessment of method accuracy (trueness and precision) by using validation standards

Assessment of accuracy of analytical methods is a fundamental stage in method validation. The use of validation standards enables the assessment of both trueness and precision of analytical methods at the same time. Procedures of intra-laboratory testing of method accuracy using validation standards are outlined and discussed.     

Recent developments in liquid chromatography--impact on qualitative and quantitative performance

In order to reduce the analysis time and maintain good efficiency in liquid chromatography (LC), several solutions are currently being investigated. The focus of this study was to compare, both qualitatively and quantitatively, the chromatographic performance of a conventional LC with selected approaches, namely monolithic supports, high temperature LC (up to 90 degrees C), and sub-2 microm particles combined with high pressure (up to 1000 bar). This comparison was achieved from a qualitative point of view with a special attention paid to the analysis of time reduction, efficiency improvement, and pressure constraint. For this purpose, the different approaches were discussed using Knox curves and other kinetic plots. It appeared that columns packed with sub-2 microm particles under high-pressure conditions (UPLC) were well adapted and this option represents an attractive alternative to conventional LC; however, the other alternative approaches should not be neglected. The quantitative evaluation of these techniques was performed on the basis of the validation of results of a pharmaceutical formulation (Rapidoca?ne), following SFSTP 2003 guidelines. Fast-LC approaches demonstrated equivalent performance to conventional LC in terms of trueness, precision, and accuracy profile, with a significant time reduction (up to 8x) according to the selected methodology.     

Determination of L-753,037 in human plasma by liquid chromatography/turbo ionspray tandem mass spectrometry.

A liquid chromatographic/turbo ionspray tandem mass spectrometric (LC/MS/MS) method was developed and validated for the determination of L-753,037, a potent endothelin receptor antagonist currently under development for the treatment of cardiovascular diseases, in human plasma. L-753,037 is extracted from 0.5 ml of human plasma using liquid-liquid extraction and analyzed by LC/MS/MS with a turbo ionspray interface. Method validation results showed that this method is very sensitive, reliable, selective and reproducible. L-753,048, an ethoxy analogue of L-753,037, was used as the internal standard. The method has a lower limit of quantitation (LOQ) of 50 pg ml(-1) with a linear calibration range of 0.05-50 ng ml(-1). The intra-day precision and accuracy (n = 5) were measured to be below 10% relative standard deviation (RSD) and between 97.4 and 102.8% of the nominal values, respectively, for all calibration standard concentrations within the calibration curve range. The inter-day precision and accuracy (n = 3 days, 5 replicates per day) were measured to be below 6.5% RSD and between 99.3 and 102.0% of the nominal values, respectively, for all quality control concentrations. The extraction recovery was determined to be approximately 99% on average. The analyte was found to be stable in plasma through three freeze-thaw cycles, for at least 4 h at ambient temperature and for up to 40 days under -20 degrees C freezer storage conditions. The analyte was also shown to be stable for at least 24 h in the reconstitution solution at room temperature and for up to 3 days as a dried extract at 4 degrees C. Additional variations in plasma concentration of the analyte due to the use of different sources of plasma were also evaluated.