高功率高光束质量脉冲Nd: YAG激光器

 以实现高功率、高光束质量的脉冲激光输出为目的,对非对称平-凹谐振腔的结构进行了理论分析。设计出了高功率、高光束质量非对称放置的平-凹谐振腔、双氙灯泵浦的脉冲Nd: YAG激光器。当占空比为9%时,实现输出激光平均功率近480 W,光束参数积优于12.7 mm·mrad,电光转化效率近4%,与理论分析吻合,可用芯径300 μm的光纤传输,不稳定性优于±1%。加工实验证明有较好的质量：切割材料为不锈钢,厚度为3 mm时、切割速度为0.6 m/min和厚度为1.5 mm、切割速度为1.2 m/min时,两种情况下所得切缝宽度均为250 μm,且切割上下沿光滑。     

高功率高光束质量脉冲Nd: YAG激光器

以实现高功率、高光束质量的脉冲激光输出为目的,对非对称平-凹谐振腔的结构进行了理论分析。设计出了高功率、高光束质量非对称放置的平-凹谐振腔、双氙灯泵浦的脉冲Nd: YAG激光器。当占空比为9%时,实现输出激光平均功率近480 W,光束参数积优于12.7 mm·mrad,电光转化效率近4%,与理论分析吻合,可用芯径300 μm的光纤传输,不稳定性优于±1%。加工实验证明有较好的质量：切割材料为不锈钢,厚度为3 mm时、切割速度为0.6 m/min和厚度为1.5 mm、切割速度为1.2 m/min时,两种情况下所得切缝宽度均为250 μm,且切割上下沿光滑。     

1064 nm Nd:YAG激光诱导铁等离子体特征参数的研究

利用1064 nm Nd:YAG激光器研究了激光诱导铁条等离子体的特征参数。为了减小测量误差和谱线自发辐射跃迁几率不确定性带来的计算误差,采用改进的迭代Boltzmann方法精确求解铁等离子体的电子温度为8058 K。Lorentz函数拟合Fe I 376.553 nm得到等离子体的电子数密度为8.71017 cm-3。分析表明等离子体的加热机制主要是逆轫致过程,其吸收系数是0.14 cm-1。实验数据证实激光诱导铁等离子体处于局部热力学平衡状态和光学薄状态。     

1064 nm Nd:YAG激光诱导铁等离子体特征参数的研究

利用1064 nm Nd:YAG激光器研究了激光诱导铁条等离子体的特征参数。为了减小测量误差和谱线自发辐射跃迁几率不确定性带来的计算误差,采用改进的迭代Boltzmann方法精确求解铁等离子体的电子温度为8058 K。Lorentz函数拟合Fe I 376.553 nm得到等离子体的电子数密度为8.71017 cm-3。分析表明等离子体的加热机制主要是逆轫致过程,其吸收系数是0.14 cm-1。实验数据证实激光诱导铁等离子体处于局部热力学平衡状态和光学薄状态。     

Investigation of Cr:YAG passive mode-locking in a pulsed Nd:YAG laser

Passive mode-locking of a pulsed Nd:YAG laser using a Cr⁴⁺:YAG saturable absorber was realized for the first time in a nearly critical stable resonator containing an antiresonant ring structure. The output energy and pulse duration are 13.5 mJ and 180 ps, respectively. The recovery time and saturable intensity for excited-state absorption of Cr⁴⁺:YAG under the action of strong laser pulses were calculated from rate equations.     

Experimental study of electro-optical-switched pulsed Nd:YAG laser

We report the specification of a compact and stable side diode-pumped Q-switched pulsed Nd:YAG laser. We experimentally study and compare the performance of the pulsed Nd:YAG laser in the free-running and Q-switched modes at different pulse repetition rates from 1 Hz to 100 Hz. The laser output energy is stabilized by using a special configuration of the optical resonator. In this laser, an unsymmetrical concave–concave resonator is used and this structure helps the mode volume to be nearly fixed when the pulse repetition rate is increased. According to the experimental results in the Q-switched operation, the laser output energy is nearly constant around 70 m J with an FWHM pulse width of 7 ns at100 Hz. The optical-to-optical conversion efficiency in the Q-switched regime is 17.5%.     

UV laser micromachining of piezoelectric ceramic using a pulsed Nd:YAG laser

UV laser (=355 nm) ablation of piezoelectric lead zirconate titanate (PZT) ceramics in air has been investigated under different laser parameters. It has been found that there is a critical pulse number (N=750). When the pulse number is smaller than the critical value, the ablation rate decreases with increasing pulse number. Beyond the critical value, the ablation rate becomes constant. The ablation rate and concentrations of O, Zr and Ti on the ablated surface increase with the laser fluence, while the Pb concentration decreases due to the selective evaporation of PbO. The loss of the Pb results in the formation of a metastable pyrochlore phase. ZrO₂ was detected by XPS in the ablated zone. Also, the concentrations of the pyrochlore phase and ZrO₂ increase with increasing laser fluence. These results clearly indicate that the chemical composition and phase structure in the ablated zone strongly depend on the laser fluence. The piezoelectric properties of the cut PZT ceramic samples completely disappear due to the loss of the Pb and the existence of the pyrochlore phase. After these samples were annealed at 1150 °C for 1 h in a PbO-controlled atmosphere, their phase structure and piezoelectric properties were recovered again. Finally, 1–3 and concentric-ring 2–2 PZT/epoxy composites were fabricated by UV laser micromachining and their thickness modes were measured by impedance spectrum analysis and a d₃₃ meter. Both composites show high piezoelectric properties. PACS 81.40.Gh; 77.84.-s     

Laser welding of glasses using a nanosecond pulsed Nd:YAG laser

This work reports on laser welding of two 1 mm thickness borosilicate glasses through the irradiation with a nanosecond pulsed laser, as a novel alternative to the use of ultrashort pulsed lasers for welding of transparent materials. Two different methodologies were investigated and compared in terms of interface quality. In a first approach, the glasses were joined without any absorbing intermediate layer. However, the bond interface possesses defects. To improve the resulting bond interface, the use of a titanium ultrathin intermediate layer was proposed to weld the glasses substrates, acting as a sealant between them. The laser parameters were optimized to achieve the best joining conditions of the Ti film. The use of the Ti layer gives rise to a bond interface more homogeneous and free of damages. As a further step, thin glasses of 86 µm thickness, of great technological value, were joined through the Ti film as well. The joined interfaces were inspected through optical microscopy and scanning electron microscopy (SEM) while the bond quality was evaluated by Scanning Acoustic Microscopy (SAM).     

Experimental study of electro-optical Q-switched pulsed Nd:YAG laser

We report the specification of a compact and stable side diode-pumped Q-switched pulsed Nd:YAG laser. We experimentally study and compare the performance of the pulsed Nd:YAG laser in the free-running and Q-switched modes at different pulse repetition rates from 1 Hz to 100 Hz. The laser output energy is stabilized by using a special configuration of the optical resonator. In this laser, an unsymmetrical concave-concave resonator is used and this structure helps the mode volume to be nearly fixed when the pulse repetition rate is increased. According to the experimental results in the Q-switched operation, the laser output energy is nearly constant around 70 mJ with an FWHM pulse width of 7 ns at 100 Hz. The optical-to-optical conversion efficiency in the Q-switched regime is 17.5%.     

Hollow-fiber delivery of high-power pulsed Nd:YAG laser light

We propose hollow fibers for delivery of high-peak-power pulsed Nd:YAG laser light. Hollow fibers with an internal polymer layer were fabricated by a liquid-phase coating technique. We reduced the losses of the fibers in the near-infrared region by producing a silver film that was very smooth owing to use of an ultrasonic wave for mixing of the silver and the reducer solutions in the silver-plating process. The straight losses of the 1-m-long polymer-coated fibers were 0.3 dB for the 700-mum bore size and 0.1 dB for the 1000-mum bore fiber.     

Improvement in solar-pumped Nd:YAG laser beam brightness

Solar-pumped solid-state lasers are promising for renewable extreme-temperature material processing. Here we report a large improvement in solar laser beam brightness by pumping a thin Nd:YAG single crystal rod. A fused silica light guide of 14 mm×22 mm rectangular cross-section is used to both transmit and homogenize the concentrated solar radiation from the focal zone of a 2.88 m² parabolic mirror to the entrance aperture of a modified 2D-CPC flooded pump cavity, within which a 4 mm diameter rod is efficiently pumped. 2.2% slope efficiency is reached. Laser beam brightness figure of merit B is three times higher than that of the most recent solar-pumped Nd:YAG laser by a Fresnel lens. The introduction of the rectangular cross-section light guide has also ensured a much more stable laser emission than previous pumping schemes.     

Biocompatible film deposition by using Nd:YAG pulsed laser

A Nd:YAG laser operating at the fundamental wavelength (1064 nm) and at the second harmonic (532 nm), with 9 ns pulse duration, 100–900 mJ pulse energy, and 30 Hz repetition rate mode, was employed to ablate in vacuum (10^?6 mbar) biomaterial targets and to deposit thin films on substrate backings. Titanium target was ablated at the fundamental frequency and deposited on near-Si substrates. The ablation yield increases with the laser fluence and at 40 J/cm ² the ablation yield for titanium is 1.2×10¹⁶ atoms/pulse. Thin film of titanium was deposited on silicon substrates placed at different distance and angles with respect to the target and analysed with different surface techniques (optical microscopy, scanning electron spectrosopy (SEM), and surface profile).

Hydroxyapatite (HA) target was ablated to the second harmonic and thin films were deposited on Ti and Si substrates. The ablation yield at a laser fluence of 10 J/cm ² is about 5×10¹⁴ HA molecules/pulse. Thin film of HA, deposited on silicon substrates placed at different distance and angles with respect to the target, was analysed with different surface techniques (optical microscopy, SEM, and Raman spectroscopy).

Metallic films show high uniformity and absence of grains, whereas the bio-ceramic film shows a large grain size distribution. Both films found special application in the field of biomaterial coverage.     

Cutting of nonmetallic materials using Nd:YAG laser beam

This study deals with Nd:YAG laser cutting nonmetallic materials, which is one of the most important and popular industrial applications of laser. The main theme is to evaluate the effects of Nd:YAG laser beam power besides work piece scanning speed. For approximate cutting depth, a theoretical study is conducted in terms of material property and cutting speed. Results show a nonlinear relation between the cutting depth and input energy. There is no significant effect of speed on cutting depth with the speed being larger than 30 mm/s. An extra energy is utilized in the deep cutting. It is inferred that as the laser power increases, cutting depth increases. The experimental outcomes are in good agreement with theoretical results. This analysis will provide a guideline for laser-based industry to select a suitable laser for cutting, scribing, trimming, engraving, and marking nonmetallic materials.     

用倍频晶体KTP实现Nd：YAG激光锁模的研究

报道用倍频晶体KTP实现Nd:YAG激光锁模的系统研究,给出了该锁模激光器输出脉宽的表达式,并和实验测量值相比较,计算值跟实验结果符合较好.文中还分析了各种参数对该锁模激光输出性能的影响.     

Simple Nd:YAG laser generates vector and vortex beam

We report a simple Nd:YAG laser that emits radially polarized beam with helical wavefront. The laser cavity consists of a piece of laser crystal and a plane output coupler, and there is no additional polarization component inside it. The pump light is converted into annular profile through de-focal coupling into a multi-mode fiber. For the continuous-wave(CW) operation, the laser emits radially polarized vortex beam, and it is observed that the helical wavefront of the laser beam is switched from right handedness to left handedness when the output coupler is tilted slightly. For the Q-switched operation under the insertion of a Cr4t:YAG saturable absorber inside the cavity, we obtain radially polarized outputs with left-handedness helical wavefront. By tilting the laser crystal slightly, the laser output switches to azimuthal polarization at pump power larger than 4.5 W and left-handedness helical wavefront of laser beam is preserved.     

Stable seeder-injected Nd:YAG pulsed laser using a RbTiOPO_4 phase modulator

A stable, single-longitudinal-mode, nanosecond-pulsed Nd:YAG laser with a laser-diode dual-end pumping arrangement is constructed. Injection seeding is performed successfully by utilizing a Rb Ti OPO4 crystal as the intracavity phase modulator to change the optical length of the slave cavity based on the delay-ramp-fire technique. The laser generates 9.9 m J of pulse energy with a 16 ns pulse duration at a 400 Hz repetition rate.A near-diffraction-limit laser beam is achieved with a beam quality factor M2 of approximately 1.2. The frequency jitter is 1.5 MHz over 2 min, and the fluctuation of the output pulse power is 0.3% over 23 min.     

高平均功率六棒串接脉冲Nd:YAG激光器

报道了一种腔内六棒串接的脉冲Nd:YAG激光器。采用44矩阵对晶体棒失调角度对谐振腔光轴的影响进行了理论分析,给出了六棒串接脉冲激光器中晶体棒失调角度的允许范围。在串接实验中,谐振腔采用对称平平腔结构,通过调整每根晶体棒的失调角度到允许范围内,实现了六棒串接脉冲Nd:YAG激光器。在输入电功率86 kW,占空比17%时,获得了平均功率3 018 W的脉冲激光输出,峰值功率17.75 kW,最高单脉冲能量为66 J,光束参数乘积为26.3 mmmrad,电光转换效率3.5%,长时间工作不稳定性小于2%。     

Reduction of beam divergence of a thermal lensing insensitive Nd:YAG laser

In a previous paper we proposed an active resonator designed especially for Nd:YAG lasers. The beam generated by this resonator had a flat-top beam profile and a divergence that was insensitive to the thermal lensing effect. The beam generated by this resonator was, however, too divergent to be focused into a fibre. With the help of numerical simulations, we have found a way to reduce this divergence, and to render the far-field of the laser beam fine enough to be coupled into a fibre with 600 μm core and NA = 0.2.     

高平均功率六棒串接脉冲Nd:YAG激光器

报道了一种腔内六棒串接的脉冲Nd:YAG激光器。采用44矩阵对晶体棒失调角度对谐振腔光轴的影响进行了理论分析,给出了六棒串接脉冲激光器中晶体棒失调角度的允许范围。在串接实验中,谐振腔采用对称平平腔结构,通过调整每根晶体棒的失调角度到允许范围内,实现了六棒串接脉冲Nd:YAG激光器。在输入电功率86 kW,占空比17%时,获得了平均功率3 018 W的脉冲激光输出,峰值功率17.75 kW,最高单脉冲能量为66 J,光束参数乘积为26.3 mmmrad,电光转换效率3.5%,长时间工作不稳定性小于2%。