铜磷铝分子筛的合成及其对苯液相氧化制苯酚的催化性能

 以水热法合成了铜磷铝分子筛(Cu-AlPO4-5),并用XRD,ICP,SEM,FT-IR,NH3-TPD,H2-TPR,ESR和N2吸附-脱附等手段对样品进行了表征. 结果表明,所合成的Cu-AlPO4-5分子筛具有AFI拓扑结构,结晶度高,无结晶态杂质; Cu2+进入到分子筛的骨架结构中,并使其Lewis酸和Brnsted酸中心数量增加,弱酸性中心大大增强,强酸性中心消失; 样品中的Cu存在多种形式,以骨架Cu物种为主,还存在 泄羌芡釩uO和双核Cu物种,部分样品具有缺陷结构. Cu-AlPO4-5分子筛中存在着骨架Cu和缺陷结构两种可能的活性中心,对苯液相氧化具有良好的催化性能,苯酚选择性可达96%,收率可达6.9%.     

Fe-MSU-1介孔分子筛的合成及其催化苯酚羟基化性能

以月桂醇聚氧乙烯醚为模板剂,在中性条件下成功合成了Fe-MSU-1介孔分子筛.采用X射线衍射、傅里叶变换红外光谱、紫外-可见吸收光谱、电子自旋共振谱、透射电镜、低温N2吸附和电感耦合等离子体原子发射光谱对样品进行了表征.考察了Fe-MSU-1分子筛在苯酚羟基化反应中的催化性能以及工艺条件对苯酚羟基化反应的影响.结果表明,Fe3 离子进入了分子筛骨架,Fe-MSU-1分子筛具有均一的蠕虫状介孔结构,平均孔径约为2.9nm.在焙烧后的Fe-MSU-1样品中,Fe3 主要以四配位的形式存在,无骨架外Fe2O3物种形成.以水为溶剂,在苯酚/H2O2摩尔比为3,反应温度353K,反应时间7h的条件下,苯酚和H2O2的转化率以及苯二酚的选择性分别达到20.4%,96.9%和99.6%.     

Mo/HZSM-5催化剂上甲烷无氧芳构化反应——HZSM-5分子筛脱铝的影响

采用两种不同的脱铝方法对HZSM-5分子筛进行了预处理,并利用MAS NMR和吸附吡啶的FT-IR对分子筛的结构和酸性质进行了表征,考察了分子筛的脱铝程度对Mo基催化剂上甲烷芳构化反应性能的影响.结果表明,HZSM-5分子筛的酸性过强或B酸量不足,均会导致催化剂严重积炭,但积炭成因不同.母体HZSM-5分子筛上的强B酸中心的存在可促使催化剂上反应中间物种深度脱氢,造成催化剂在反应过程中严重积炭.经水热处理的HZSM-5分子筛,骨架铝脱出严重,造成B酸活性中心不足以及部分微孔阻塞,不利于C2中间物种芳构化,导致芳烃选择性显著降低.经高温N2处理的HZSM-5分子筛,骨架铝脱出相对缓和,在消除母体分子筛上强B酸中心的同时,保留了较多的弱B酸中心,既可满足C2中间物种芳构化反应的需要,又可有效抑制催化剂积炭,导致甲烷芳构化反应性能显著改善.     

无铝V-β分子筛的合成、表征及催化性能研究

采用水热晶化法在SiO2-V2O5-(TEA)2O-NH4F-H2O体系中合成了无铝V-β分子筛,运用XRD,IR,UV-Vis漫反射,TG/DTA和SEM等技术表征了样品的物理化学特性,证明样品具有BEA拓扑结构,结晶良好,且钒原子进入了分子筛骨架. 探讨了反应混合物组成对V-β分子筛晶化的影响,在以H2O2为氧化剂的苯酚羟基化反应中,考察了V-β分子筛的催化氧化性能.     

合成因素对V-AlPO4-5骨架钒含量和催化苯氧化性能的影响

水热法合成了V-AlPO4-5分子筛，用XRD和FT-IR对样品进行了表征．以纯V-AlPO4-5分子筛为基准，用样品单位晶胞体积的膨胀程度和红外谱图中骨架振动峰向低波数方向位移程度的大小为指标，定性地探索了钒源、加料方式、钒加入量和晶化时间等合成因素对于V-AlPO4-5分子筛中骨架钒含量的影响．结果表明以V2O5为钒源、采用(V P H2O) Al R的加料方式，V／(Al P)=1／80，200℃下水热晶化48h后得到的V-AlPO4-5分子筛中骨架钒含量最高．H2O2氧化苯制苯酚的活性实验结果表明，苯酚收率和H2O2分解率同V-AlPO4-5骨架钒含量具有明显的正相关性．溶剂效应表明反应机理是羟基自由基机理．     

HZSM-5沸石分子筛上苯酚与甲醇的烷基化反应

 在n（PhOH）／n（CH3OH）＝1,WGSV＝0．5h－1,T＝673K的反应条件下,研究了HZSM－5,HZSM－23和改性HZSM－5分子筛上苯酚与甲醇烷基化反应的规律．结果表明,分子筛外表面的酸中心对苯酚烷基化反应的贡献较大．用4－甲基喹啉使分子筛外表面的酸中心中毒后,影响反应产物选择性的主要因素是分子筛的孔径．孔径较小的HZSM－23分子筛对提高芳香醚的选择性,抑制二甲酚的生成和提高对甲酚的选择性有利．间甲酚和二甲酚可以在HZSM－5沸石的孔道内生成,但在HZSM－23的孔道内受到抑制．用P2O5,MgO和Sb2O3对HZSM－5改性都可以提高芳香醚的选择性,降低甲酚和二甲酚的选择性．随着氧化物负载量的增加,邻甲酚选择性升高．适度的氧化物改性可以提高对甲酚的选择性,改性效果为Sb2O3＞P2O5＞MgO．     

钴分子筛催化剂的制备及其分子筛载体对环己烷氧化选择性的影响

为了考察催化剂载体的孔道结构和择形性能对环己烷部分氧化反应的影响,采用直接水热法制备出了Co/S-1,Co/TS-1以及Co/MCM-41分子筛催化剂.XRD,FT-IR和SEM结果表明合成的样品具有较高的结晶度,晶粒大小均匀,其活性组分钴进入了分子筛骨架.采用氧气为氧化剂,考察了合成的钴催化剂样品对环己烷部分氧化的催化性能,并与CoAPO-5、Co/A l2O3、均相Co(OAc)2.4H2O催化剂以及无催化氧化的结果进行了比较.实验结果表明:分子筛载体能利用其孔道结构和择形性能,降低环己醇(酮)选择性对环己烷转化率的依赖性,且反应的选择性随分子筛载体孔径的增加而下降.孔道较小的Co/TS-1和Co/S-1做催化剂时,过氧化物含量低,环己烷转化率可达5%以上,同时反应总选择性为95%左右.     

Co-ZSM-5催化剂上乙烯选择性催化还原Nox表面中间物种的组成

 采用预处理-瞬态反应产物分析方法定量研究了Co-ZSM-5催化剂上乙烯选择性催化还原氮氧化物反应过程中表面中间物种的组成. 催化剂在275 ℃经0.1%NO-0.05%C2H4-10%O2/Ar混合气处理后生成了表面中间物种NCaObHc, 该物种与NO/O2/Ar混合气反应比与单独的NO或O2反应生成更多的N2. 通过质谱、红外吸收四组分 (CO2, CO, CH4和N2O)分析仪及气相色谱-质谱联用等技术分析了表面中间物种与NO/O2/Ar混合气反应的产物,确定了表面中间物种中三种元素N, C和H的平均原子数之比为1.0∶1.8∶5.0 (氧物种由于实验原因很难确定).     

TS-1分子筛对固定床中苯酚羟基化反应的催化性能

 制备了用于固定床反应器的负载型TS－1分子筛催化剂,并以苯酚羟基化为探针反应,研究了载体、钛含量和预处理剂等对负载型TS－1分子筛催化性能的影响,考察了固定床反应器中苯酚羟基化反应的工艺条件．结果表明,酸性较强的载体会加剧H2O2的分解,导致苯酚的转化率和H2O2的有效利用率下降;在所研究的ZSM－5,TiO2,Al2O3,ZrO2,SiO2和硅藻土载体中,硅藻土具有最好的催化性能;催化剂的活性与骨架钛含量有关;用HNO3,KAc,NaAc,NH4Ac和NH4Cl处理过的催化剂,活性和选择性得到提高,而用NH3·H2O,Na2CO3和Na3PO4等碱性物质处理后,催化剂的活性则下降;溶剂、反应温度、原料空速和苯酚／H2O2摩尔比对苯酚羟基化反应有很大影响．以丙酮为溶剂,在苯酚／H2O2摩尔比为3,反应温度为84℃,WHSV为8．46h－1的反应条件下,苯酚转化率、H2O2转化率、苯二酚选择性以及H2O2的有效利用率可分别达到27．7％,94．8％,97．7％和75．1％．     

H5PMo10V2O40/SBA-15催化剂的制备及其催化性能

以Keggin型杂多酸H5PMo10V2O40为主体,SBA-15介孔分子筛为载体,利用溶胶-凝胶法制备了不同负载量的H5PM10V2O40/SBA-15负载型催化剂,通过XRD、FTIR、TEM、H2-TPR和N2吸脱附法对样品进行了分析和表征,并将制得的负载型催化剂应用于苯氧化苯酚的反应中,研究了不同条件(温度、时间和催化剂用量等)下的催化性能.研究结果表明:H5PMo10V2O40杂多酸能均匀地分散于SBA-15孔道中且SBA-15的六方介孔结构并未发生改变:较好地解决了活性组分大量溶脱的问题;与H5PMo10V2O40杂多酸相比,H5PMo10V2O40/SBA-15催化剂在苯氧化为苯酚的反应中具有更高的转化率和更好的选择性,当反应温度为70℃,催化剂的使用量为0.25 g,反应时间为2 h和H5PMo10V2O40负载量为60%时苯酚的选择性达到了82.53%.     

Dichroism of absorption and polarization of phosphorescence of molecules of the closed form of nitrobenzospirothiopyran

The spectral-polarization characteristics of absorption and phosphorescence of molecules of the initial form of nitro-substituted indolinospirobenzothiopyran were studied in oriented polyethylene films and in solutions with different polarity. An oscillator model of the electron transitions responsible for the formation of absorption and luminescence spectra was suggested. It was established that the principal differences in the spectral and photophysical properties of the compound studied and its oxygen-containing analog are associated with the fact that the electronegativity of the S atom is lower than that of the O atom. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 6, pp. 1143–1146, June, 1997.     

非那雄胺合成工艺改进

非那雄胺能抑制5α-还原酶的活性,明显降低二氢睾酮水平,是一种治疗良性前列腺增生的有效药品。该合成工艺以甾烯酮酸为原料,将其与氯化亚砜反应,无须分离即与叔丁胺反应得17β-酰胺化合物,再氧化开环,环合,氢化,脱氢合成了非那雄胺。经元素分析、IR、1HNMR、13CNMR、MS分析表征了其结构。该法无须使用昂贵的2,2-二吡啶二硫化物和剧毒药品苯亚硒酸酐,且以乙酸铵代替氨气,降低了对设备的要求和腐蚀,更适用于工业生产。     

Determination of heats of detonation and influence of components of composite explosives on heats of detonation of high explosives

The heats of detonation of 20 simple high explosives and explosive mixtures were determined by means of an adiabatic detonation calorimeter designed by the authors. The results indicated that the performance of the instrument was reliable and the experimental data were very accurate. For explosive mixtures, there was a linear accumulative relationship between the heats of detonation of the explosive mixture and its components. Accordingly, the heats of detonation of explosive mixtures could be calculated directly from the heats of detonation of simple explosives and the characteristic heats of other components. The experiments showed that the gold or brass shell of the cylindrical charge could be substituted by a thick-walled porcelain shell, which had the advantage of cheapness.

     

Synthesis of phenolic components of Grains of Paradise

Two vanilloids, (5E)-8-(4-hydroxy-3-methoxyphenyl)oct-5-en-4-one (1) and 4-[3-hydroxydecyl]-2-methoxyphenol (2), isolated from the dried seeds of Grains of Paradise (Aframomum melegueta), were synthesized; the latter compound was made as the S-enantiomer and the material derived from the seeds was found to be a 1:1.7 mixture of the R and S isomers. The synthetic route used should allow the preparation of analogs having extended alkyl chains and consequently different lipophilicity, and 3, a homolog of 2, was also prepared.     

Summary of development of the theory of stability of colloids and thin films

In this review, the research of the author in the field of colloidal systems is summarized. The factors influencing colloidal stability are systematized and analyzed. Examples are presented to illustrate the practical utilization of the theory of stability of colloids and thin films.This review was prepared on the basis of the works of the author, which were awarded the State Premium for 1991 in the field of science and technology, chemistry section.Institute of Physical Chemistry, Russian Academy of Sciences, 117915 Moscow. Translated from Izvestiya Akademii Nauk, Seriya Khimicheskaya, No. 8, pp. 1708–1717, August, 1992.     

Study of hydration of two cements of different strengths

Main hydration products of two cement pastes, i.e. CSH-gel, portlandite (P) (and specific surface S) were studied by static heating, and by SEM, TEM and XRD, as a function of cement strength (C-33 and C-43) hydration time (th) and subsequent hydration in water vapour.Total change in mass on hydration and air drying, M_o, increased with strength of cement paste and with hydration time. Content of water escaping at 110 to 220°C, defined as water bound with low energy, mainly interlayer and hydrate water, was independent on cement strength but its content increased with (th). Content of chemically bound (zeolitic) water in CSH-gel, escaping at 220-400°C, was slightly dependent on strength and increased with (th). It was possibly derived from the dehydroxylation of CSH-gel and AFm phase. Portlandite water, escaping at 400-500°C, was independent on cement strength and was higher on longer hydration. Large P crystals were formed in the weaker cement paste C-33. Smaller crystals were formed in C-43 but they increased with (th). Carbonate formated on contact with air (calcite, vaterite and aragonite), decomposed in cement at 600-700^oC. It was high in pastes C-33(1 month) and C-43(1 month), i.e. 5.7 and 3.3%, respectively; it was less than 1% after 6 hydration months (low sensitivity to carbonation) in agreement with the XRD study showing carbonates in the air dry paste (1month), and its absence on prolonged hydration (6 months) and on acetone treatment. Water vapour treatment of (6 months) pastes or wetting-drying increased this sensitivity.Nanosized P-crystals, detected by TEM, could contribute to the cement strength; carbonate was observed on the rims of gel clusters.This revised version was published online in November 2005 with corrections to the Cover Date.     

氯氧化镁生成热的研究

用氧化镁氯化镁水溶液制备了8水合氯氧化镁[nMg(OH)2·MgCl2·8H2O], 并测定了其在盐酸中的溶解热, 实验结果表明, 氯氧化镁溶解热与n值呈线性关系, 根据溶解热求出5Mg(OH)2·MgCl2·8H2O和3Mg(OH)2·MgCl2·8H2O的生成热分别为-7727.1和5888.1kJ·mol^1^-。     

Thermodynamics of the formation of oxosulfides of rare-earth elements

The enthalpies of solution of several oxosulfides of rare-earth elements and the high-temperature enthalpies of oxosulfides and oxosulfates of lanthanum and yttrium were measured using solution calorimetry and high-temperature microcalorimetry techniques. Standard enthalpies of formation and some thermodynamic properties of oxosulfides and oxosulfates were calculated. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 2 pp. 294–297, February, 1997.     

探究“铁的锈蚀条件”实验创新设计

设计了铁的锈蚀实验,说明了铁钉的处理方法,增加了温度、酸、碱的影响条件,实现了铁跟蒸馏水及空气中氧气快速反应而生锈,使实验在5 min左右就能够得到准确的结果。