Micromachined high frequency PMN-PT/epoxy 1-3 composite ultrasonic annular array

This paper reports the design, fabrication, and performance of miniature micromachined high frequency PMN-PT/epoxy 1-3 composite ultrasonic annular arrays. The PMN-PT single crystal 1-3 composites were made with micromachining techniques. The area of a single crystal pillar was 9 × 9 μm. The width of the kerf among pillars was ∼5 μm and the kerfs were filled with a polymer. The composite thickness was 25 μm. A six-element annular transducer of equal element area of 0.2 mm² with 16 μm kerf widths between annuli was produced. The aperture size the array transducer is about 1.5 mm in diameter. A novel electrical interconnection strategy for high density array elements was implemented. After the transducer was attached to the electric connection board and packaged, the array transducer was tested in a pulse/echo arrangement, whereby the center frequency, bandwidth, two-way insertion loss (IL), and cross talk between adjacent elements were measured for each annulus. The center frequency was 50 MHz and −6 dB bandwidth was 90%. The average insertion loss was 19.5 dB at 50 MHz and the crosstalk between adjacent elements was about −35 dB. The micromachining techniques described in this paper are promising for the fabrication of other types of high frequency transducers, e.g. 1D and 2D arrays.     

Characterization of a tunable three-section slotted Fabry-Perot laser for advanced modulation format optical transmission

In this paper we report on the characterization of a narrow linewidth three-section tunable slotted Fabry-Perot laser. The SMSR of the 25 available 100-GHz ITU channels is above 30 dB, whereas their average linewidth is 538 kHz with a maximum below 800 kHz. The RIN spectra of six different channels are also measured and a maximum average RIN of −135 dB/Hz is obtained. The linewidth effect of the laser in a 1.25 Gb/s DPSK transmission system is investigated by comparing the performance between the slotted Fabry-Perot laser and a commercial SG-DBR laser respectively. Error free transmission of the slotted Fabry-Perot laser shows the benefit of the narrow linewidth of the device for systems employing advanced modulation formats.     

High-frequency signal processing using magnetic layered structures

We present a review of theoretical and experimental results for tunable microwave band-stop filters, band-pass filters, phase shifters, and a signal to noise enhancer, all based on a microstrip geometry and using a variety of magnetic thin films and layered structures. These devices are compatible in size and growth process with on-chip high-frequency electronics. For devices based on metallic ferromagnetic films of Fe and Permalloy, the operational frequency ranges from 5 to 35 GHz for external fields below 5 kOe. For the band-stop filters, we observed power attenuation up to ∼100 dB/cm, and an insertion loss on the order of ∼2-3 dB, for both Permalloy and Fe-based structures. We also explore the use of thin films of hexagonal ferrites, antiferromagnets, and liquid crystals, and show that useful devices can be constructed with films less than one 1 μm in thickness.     

A row–column addressed micromachined ultrasonic transducer array for surface scanning applications

Row–column addressed arrays for ultrasonic non-destructive testing (NDT) applications are analyzed and demonstrated in this paper. Simulation and experimental results of a row–column addressed 32 by 32 capacitive micromachined ultrasonic transducer (CMUT) array are presented. The CMUT array, which was designed for medical imaging applications, has a center frequency of 5.3 MHz. The CMUT array was used to perform C-scans on test objects with holes that have diameters of 1.0 mm and 0.5 mm. The array transducer has an aperture size of 4.8 mm by 4.8 mm, and it was used to scan an area of 4.0 mm by 4.0 mm. Compared to an N by N fully addressed 2-D array, a row–column addressed array of the same number of elements requires fewer (N instead of N²) pairs of interconnection and supporting electronic components such as pulsers and amplifiers. Even though the resulting field of view is limit by the aperture size, row–column addressed arrays and the row–column addressing scheme can be an alternative option of 2-D arrays for NDT applications.     

Ultrasonic transmission through multiple-sublattice subwavelength holes arrays

The ultrasonic transmission through plates perforated with 2 × 2 or 3 × 3 square array of subwavelength holes per unit cell are studied by numerical simulations. Calculations are obtained by means of a theoretical model under the rigid-solid assumption. It is demonstrated that when the inter-hole distance within the unit cell is reduced, new transmission dips appear resulting from Wood anomalies that have influence on the second and the third order Fabry-Perot peak. When the inter-hole distance within the unit cell is reduced, the transmission spectrum of the multiple-sublattice holes arrays tends to the transmission spectrum of a plate perforated with only one hole in the unit cell.     

Enhanced four-wave mixing in a high-finesse highly nonlinear fiber Fabry-Perot resonator

We have achieved a four-wave mixing process in a high-finesse highly nonlinear fiber Fabry-Perot resonator, where the amplified signal and idler were enhanced in transmission by 6 dB and 10 dB respectively comparing with those in a single fiber. We used a 6 m long low-loss Fabry-Perot resonator with two high-reflectivity fiber Bragg gratings written directly into a highly nonlinear fiber provided by Sumitomo Electric Inc., where the minimised intracavity loss resulted in the finesse in excess of 100. The resonator length was locked for 30 min by means of a modified Pound-Drever-Hall technique. The maximum intracavity power was increased by 14.3 dB by increasing the stimulated Brillouin scattering threshold with periodic phase modulation by a pseudo-random bit sequence, with length matching that of the cavity.     

Fabry-Perot interference-based fiber-optic sensor for small displacement measurement

A simple fiber-optic sensor based on Fabry-Perot interference for small displacement measurement is investigated both theoretically and experimentally. A broadband light source is coupled into a Fabry-Perot cavity formed by the surfaces of a sensing fiber end and the measured object. The interference signals from the cavity are reflected back into the same fiber. A small displacement via changes in cavity length can be obtained by measuring the wavenumber spacing of the interference fringes. The experimental data meet with the theoretical values very well. Given the light source bandwidth of 40 nm and the initial distance of 30 μm, the proposed displacement sensing system could achieve high resolution measurement of 16 nm.     

Some improvement in Fe/Si multilayered neutron polarizor by modified sputtering geometry

Aperture geometry of magnetron sputtering unit was modified by insertion of longitudinal [B] and transverse [A] slits with respect to the motion of substrate. Fe-, Si-mono and Fe/Si multilayer [Fe (70 Å)/Si (50 Å)]₁₀ (called ML70) were grown with and without modified apertures. Maximum stress anisotropy was found in samples prepared with transverse modified aperture [A]. X-ray reflectometry (XRR) results showed a marked difference in roughness values of interdiffusion layers Fe-_Si and Si-_Fe. Magnetic measurements showed coercive field strength of 50 Oe in ML70 prepared by modified aperture geometry Fe[A]/Si[O]. A significant improvement in the neutron polarization efficiency is observed in multilayer ML70 with the use of modified aperture geometry as compared to similar sample prepared by normal aperture.     

Optical loss measurements in femtosecond laser written waveguides in glass

The optical loss is an important parameter for waveguides used in integrated optics. We measured the optical loss in waveguides written in silicate glass slides with high repetition-rate (MHz) femtosecond laser pulses. The average transmission loss of straight waveguides is about 0.3 dB/mm at a wavelength of 633 nm and 0.05 dB/mm at a wavelength of 1.55 μm. The loss is not polarization dependent and the waveguides allow a minimum bending radius of 36 mm without additional loss. The average numerical aperture of the waveguides is 0.065 at a wavelength of 633 nm and 0.045 at a wavelength of 1.55 μm. In straight waveguides more than 90% of the transmission loss is due to scattering.     

678 nm RTP electro-optical Q-switched ceramic laser

The RTP electro-optical Q-switched ceramic laser at the wavelength of 678 nm with narrow pulse width is studied. We used the laser diode arrays side-pumped Nd:YAG ceramic crystal with 1.1 at% Nd doping and dimensions of Φ3 mm × 50 mm, designed folding cavity parameters, and discussed the variation of the beam radius in the ceramic crystal and frequency doubling crystal with the thermal focal length of ceramic crystal or KTP crystal. By using double RTP crystals as electro-optic Q-switch and KTP crystal type II phase matching for intracavity frequency-doubling, a narrow pulse width electro-optical Q-switched Nd:YAG ceramic laser was obtained. The output energy of 0.9 mJ and the pulse width of 41.6 ns at 678 nm are obtained at the repetition rate of 1000 Hz and pumped power of 144 W. The results formed the basis for the further development of the high power and high efficiency ceramic red laser.     

The effect of geometry and post-annealing on surface acoustic wave characteristics of AlN thin films prepared by magnetron sputtering

This paper describes experimental relationship between surface acoustic wave (SAW) properties of two-port SAW resonators based on polycrystalline aluminum nitride (AlN) thin films grown on Si substrates by using a pulsed reactive magnetron sputtering system and their geometry's parameters. Moreover, the influence of post-deposition heat treatment on SAW properties of AlN thin films was investigated at different annealing temperature (600 °C and 900 °C). The measurement results show the number of the inter-digital transducers (IDT) finger pairs (N), the number of reflectors grating pairs (R) and the IDT center-to-center distance (L) related to insertion loss of SAW resonators. The best result of insertion loss was 15.6 dB for SAW resonators with R = 160 pair, N = 5 pair and L = 750 μm. At the same geometry parameters, the SAW velocity and insertion loss were improved slightly after annealing at 600 °C and were worse for the films annealed at 900 °C by changes in the surface morphology and stress on the film.     

Design and fabrication of arrayed waveguide grating using fluoropolymer PFS-co-GMA

A 33×33 polymer arrayed waveguide grating (AWG) multiplexer is optimized and fabricated. This device is made of polymeric materials named 2,3,4,5,6-pentafluorostyrene-co-glycidylmethacrylate (PFS-co-GMA). The central wavelength and wavelength spacing are designed to be 1550.918 and 0.8 nm, respectively. The calculated results are: the 3-dB bandwidth is about 0.24 nm, insertion loss is about 8.4 dB and crosstalk is −33.7 dB. The corresponding measured results are: the center wavelength is about 1550.85 nm, wavelength channel spacing is about 0.81 nm, 3-dB bandwidth is about 0.35 nm, crosstalk is about −20 dB, insertion loss is between 10.4 dB for the central port and 11.9 dB for the edge ports.     

The influence of skew rays on angular losses in air-clad fibres

Detailed experimental transmission properties of high numerical aperture air-clad undoped fibres are presented. Measurements of the angular transmissivity indicate a 15% lower numerical aperture (NA = 0.75) compared to theoretical predictions for the bridge thickness and wavelength ratio of δ/λ = 0.226. The discrepancy is attributed to skew rays that are deliberately launched and which are subject to larger loss rates through diffractive tunnelling in frustrated total internal reflection than meridional rays. Measurements of the angular propagation losses show that light launched at angles less than the critical angle for total internal reflection experiences low initial losses as well as low propagation losses. Light launched at steeper angles experiences a significant initial loss attributed to loss of skew rays within 1.5 m of propagation as well as larger general propagation losses.     

Design and fabrication of long focal length microlens arrays

In this paper, we present microlens arrays (MLA) with long focal length (in millimeter range) based on thermal reflow process. The focal length of microlens is usually in the same order of lens diameter or several hundred microns. To extend focal length, we made a photoresist (SU-8) MLA covered by a Polydimethylsiloxane (PDMS) film on a glass substrate. Because the refractive index difference between PDMS and photoresist interface is lower than that of air and MLA interface, light is less bended when passing through MLA and is focused at longer distance. Microlenses of diameters from 50 μm to 240 μm were successfully fabricated. The longest focal length was 2.1 mm from the microlens of 240 μm diameter. The numerical aperture (NA) was reduced 0.06, which is much lower than the smallest NA (~ 0.15) by regular thermal reflow processes. Cured PDMS has high transmittance and becomes parts of MLA without too much optical power loss. Besides, other focal lengths can be realized by modifying the refractive index different between two adjacent materials as described in this paper.     

Design and performance of a compact superconducting duplexer at VHF-band

This paper presents the design, fabrication, and performance of a compact high temperature superconducting duplexer at VHF-band. The duplexer consists of a T-junction and two four-pole filters with an ultra-narrow bandwidth of 400 kHz at 216 MHz and 220 MHz, respectively. By using gap-coupled feedlines in the filter design procedure, the duplexer is constructed by connecting the two filters using a T-junction with short-length branches. The two filters are fabricated on separate substrates and are carefully packaged to achieve a high isolation between the duplexer channels. The duplexer has a compact size of 41.6 mm × 28 mm. The measured results at 73 K show a high performance. The return loss is −17 dB, the insertion losses of both channels are less than 0.16 dB, and the out-of-band rejections are higher than 60 dB. The isolation between the two channels is better than 76 dB.     

Optical power equalization for upstream traffic with injection-locked Fabry-Perot lasers in TDM-PON

An optical power equalization of upstream traffic in time-division-multiplexed passive optical network (TDM-PON) based on injection-locked Fabry-Perot lasers has been experimentally investigated. The upstream transmitters with stable spectrum are achieved by using an external injection light source in the optical line terminal (OLT). The different upstream powers can be equalized by injection locking a Fabry-Perot laser diode (FP-LD) biased below threshold current in OLT. The dynamic upstream power range from − 8.5 to − 19.5 db m is reduced to a 1.6 dB maximal power variation, when the uplink signal is directly modulated at 1.25 Gb/s.     

Compact four-channel reconfigurable optical add-drop multiplexer using silicon photonic wire

We designed and fabricated a four-channel reconfigurable optical add-drop multiplexer based on silicon photonic wire waveguide, which is controlled through the thermo-optic effect. The effective footprint of the device is about 1000 × 500 μm². The minimum insertion loss including the transmission loss and coupling loss is about 10.7 dB. The tuning bandwidth is about 17 nm, the average tuning efficiency about 6.11 mW/nm and the tuning speed about 24.5 kHz.     

Simultaneous dual-wavelength oscillation at 1116 and 1123 nm of Nd:YAG laser

We report on to our knowledge the first time a diode-side-pumped simultaneous dual-wavelength Nd:YAG laser at 1116 and 1123 nm. By inserting an etalon to balance the gain and loss, a stable dual-wavelength oscillation is acquired. The numerical simulations for wavelength tuning are discussed by principles of laser threshold and Fabry-Perot etalon. Under the pump power of 250 W, a total output power of 23 W is obtained. Meanwhile, the two components have approximately equal intensities. The beam quality of M² factor was measured to be 7.52.     

High-frequency ultrasonic transducer based on lead-free BSZT piezoceramics

This paper describes the fabrication and evaluation of a high-frequency (40 MHz) transducer based on lead-free piezoceramics for ultrasonic imaging. The transducer with an aperture size of 0.9 mm has been fabricated using barium strontium zirconate titanate ((Ba_0.95Sr_0.05)(Zr_0.05Ti_0.95)O₃, abbreviated as BSZT) ceramics. The lead-free BSZT has a piezoelectric d₃₃ coefficient of 300 pC/N and an electromechanical coupling factor k_t of 0.45. High-frequency ultrasound transducers were fabricated and a bandwidth of 76.4% has been achieved with an insertion loss of −26 dB. Applications in high resolution biological and medical imaging could be possible with this lead-free material.     

Acoustic array tracking performance under moderately complex environmental conditions

The direction-of-arrival (DOA) tracking performance of microphone arrays having aperture sizes ranging from 0.3 to 34 m is examined for an experiment involving a vehicle traversing a moderately complex terrain. A segment of the vehicle’s path was obscured behind a small, 6.7-m high, vegetated hill. The combination of the hill and upwind propagation created an acoustic shadow during this segment. DOA tracks were estimated with a minimum-variance distortionless response (MVDR) beamformer operating in two frequency bands: 25-60 Hz and 60-105 Hz. In the lower frequency band, array sizes between 1 and 8 m gave the best results, with DOA errors between 2° and 5°. Furthermore, in this band shadowing from the hill and wind refraction had a minimal affect on DOA error. In the higher frequency band, the acoustic shadow zone produced a distinct interval of high DOA error, with the 8-m array giving the best overall performance. Modeling of the beamforming process shows that high DOA errors corresponded to MVDR wavenumber patterns that are degraded by distortions to the propagating wavefronts. Our experimental results indicate that small acoustic arrays with apertures less than 0.3 m, operating at frequencies above 100 Hz, should be considered line of sight sensors. Given the moderate complexity of the test conditions, it is anticipated that the observed effects are likely to be present in most attempts to localize outdoor sound sources.