Poly(ethylene oxide) macromonomer-grafted polymer nanoparticles synthesised by emulsifier-free emulsion polymerisation

Ultrafine polymer nanoparticles based on poly(ethylene oxide) (PEO) macromonomer-grafted polystyrene (PS) have been synthesised by emulsifier-free emulsion polymerisation. In addition to the binary copolymerisation between PEO macromonomer and styrene, ternary copolymerisations were also conducted in the presence of a cationic monomer (2-(methacryloyloxy)ethyl) trimethylammonium chloride (MATMAC) as a second comonomer. The size and charge characteristics of fine nanoparticles were characterised using both photon correlation spectroscopy and transmission electron microscopy techniques as well as colloidal titration. It was found that after PEO chains (repeat unit 9 or higher) were incorporated into the PS latex, the particle size was significantly reduced owing to the steric effect contributed from grafted PEO chains. Ternary copolymerisation using MATMAC as comonomer further reduced the particle size, leading to nanoparticles as small as 60 nm. Increasing the MATMAC feed ratio gradually reduced the final size of the nanoparticle, owing to the enhancement in electrostatic stabilisation, whereas increasing the PEO macromonomer feed ratios led to slightly larger particles but significantly inhibited the agglomeration of primary particles. The formation mechanism of the nano- or microparticles with various sizes during polymerisation is discussed in terms of nucleation, agglomeration and adsorption of primary particles.     

Preparation of hemispherical particles by cleavage of micrometer-sized,spherical poly(methyl methacrylate)/polystyrene composite particle with Janus structure: effect of molecular weight

Micrometer-sized, hemispherical polymer particles were prepared as a result of cleavage of spherical Janus poly(methyl methacrylate) (PMMA)/polystyrene (PS) composite particle by treating particles with acetone/water solutions. The original PMMA/PS composite particles were prepared by the slow evaporation of toluene from homogeneous PMMA/PS/toluene droplets dispersed in aqueous solution of sodium dodecyl sulfate in advance. Appropriate molecular weights of PMMA and PS were necessary for occurrence of the cleavage of the Janus composite particle, resulting in PMMA and PS hemispherical particles. The cleavage depended on the composition of the acetone/water solution, which was explained by selective solvent absorption into the polymer phases. The results strongly support the cleavage mechanism of Janus composite polymer particles that had been proposed earlier.     

Separation of dsDNA in the presence of electroosmotic flow under discontinuous conditions

Separations of phiX-174/HaeIII DNA restriction fragments have been performed in the presence of electroosmotic flow (EOF) using five different polymer solutions, including linear polyacrylamide (LPA), poly(ethylene oxide) (PEO), hydroxypropylcellulose (HPC), hydroxyethylcellulose (HEC), and agarose. During the separation, polymer solutions entered the capillary by EOF. When using LPA solutions, bulk EOF is small due to adsorption on the capillary wall. On the other hand, separation is faster and better for the large DNA fragments (> 872 base pairs, bp) using derivative celluloses and PEO solutions. Several approaches to optimum resolution and speed by controlling EOF and/or altering electrophoretic mobility of DNA have been developed, including (i) stepwise changes of ethidium bromide (0.5-5 microg/mL), (ii) voltage programming (125-375 V/cm), (iii) use of mixed polymer solutions, and (iv) use of high concentrations of Tris-borate (TB) buffers. The DNA fragments ranging from 434 to 653 bp that were not separated using 2% PEO (8,000,000) under isocratic conditions have been completely resolved by either stepwise changes of ethidium bromide or voltage programming. Compared to PEO solutions, mixed polymer solutions prepared from PEO and HEC provide higher resolving power. Using a capillary filled with 600 mM TB buffers, pH 10.0, high-speed (< 15 min) separation of DNA (pBR 322/HaeIII digest, pBR 328/ Bg/l digest and pBR 328/Hinfl digest) has been achieved in 1.5% PEO.     

Effect of ionic strength, pH and polymer concentration on the separation of DNA fragments in the presence of electroosmotic flow

DNA separations in the presence of electroosmotic flow (EOF) using poly(ethylene oxide) (PEO) solutions have been demonstrated. During the separations, PEO entered capillaries filled with Tris-borate (TB) free buffers by EOF and acted as sieving matrices. We have found that ionic strength and pH of polymer and free solutions affect the bulk EOF and resolution differently from that in capillary zone electrophoresis. The EOF coefficient increases with increasing ionic strength of the free TB buffers as a result of decreases in the adsorption of PEO molecules. In contrast, the bulk EOF decreases with increasing the ionic strength of polymer solutions using capillaries filled with high concentrations of free TB buffers. Although resolution values are high due to larger differential migration times between any two DNA fragments in a small bulk EOF using 10 mM TB buffers, use of a capillary filled with at least 100 mM TB free buffers is suggested for high-speed separations. On the side of PEO solutions, 1.5% PEO solutions prepared in 100 to 200 mM TB buffers are more proper in terms of resolution and speed. The separation of DNA markers V and VI was accomplished less than 29 min in 1.5% PEO solutions prepared in 100 mM TB buffers, pH 7.0 at 500 V/cm using a capillary filled with 10 mM free TB buffers, pH 7.0.     

Influence of adsorbed polymers on the removal of mineral particles from a planar surface

 Experimental results on the role of adsorbed polymers on the particle adhesion are presented. Both Brownian (silica particles) and non-Brownian (glass beads) particles were used. The particles were deposited onto the internal surface of a glass parallelepiped cell, and then submitted to increasing laminar flow rates. The pH and the ionic strength of the electrolytes were fixed. The adhesive force was related to the hydrodynamic force required to dislodge 50% of the initially attached beads. We found that high molecular weight PEO had little effect on the adhesion of small silica beads due to the low affinity of the polymer for silica or glass surfaces. On the contrary, PEO greatly enhanced the adhesion of bigger glass beads forced to deposit on the capillary surface because of gravity. The increase was all the more pronounced as the molecular weight of the polymer was high. The effect of high molecular weight cationic copolymers on the adhesion of silica particles was drastic. The maximal force (1500 pN) applied by the device could not enable any particle detachment even using polymers of low cationicity rate (5%), showing the efficiency of electrostatic attractions. When copolymers were adsorbed on both surfaces (particles and plane), the adhesive force exhibited a maximum at intermediate coverage of particles. This optimum was related to the optimum flocculation concentration classically observed in flocculation of suspensions by polymers. Received: 16 February 1996 Accepted: 10 September 1996     

Gold nanoparticle/polymer nanocomposites: dispersion of nanoparticles as a function of capping agent molecular weight and grafting density

The dispersion of polymer-covered gold nanoparticles in high molecular weight (MW) polymer matrixes is reported. Complete particle dispersion was achieved for PS125-Au in the polystyrene (PS) matrixes studied (up to and including Mn = 80 000 g/mol). PS19-Au, on the other hand, exhibits complete dispersion in a low MW PS matrix (Mn = 2000 g/mol) but only partial dispersion in higher MW matrixes (up to 80 000 g/mol). Similarly, PEO45-Au is fully dispersed in a low MW poly(ethylene oxide) (PEO) matrix (Mn = 1000 g/mol) but only partially in a higher MW PEO matrix (Mn = 15 000 g/mol). Wetting of the polymer-Au brushes by the polymer matrix is associated with dispersibility. Theory predicts that, for dense polymer brushes, wetting is achieved when the MW of the polymer brush equals (and is greater than) that of the polymer matrix. The observed partial dispersion of the PS19-Au and PEO45-Au nanoparticles in matrixes whose MW is greater than the brush MW is attributable to the existence of a high volume fraction of voids within the brush. These voids arise from the unique geometry of the nanoparticle surface arising from the juxtaposed facets of the gold nanoparticle. PS125-Au brushes are wetted by PS matrixes whose degree of polymerization is larger than 125, probably because of their lower grafting density on the gold core or the high fraction of void volumes caused by the facets on the gold cores. Dispersion thus occurs when the matrix MW is greater than that of the brush.     

聚氧化乙烯水溶液粘度的测定

测定了不同分子量聚氧化乙烯(PEO)在水溶液中的粘度，发现在低浓度区高分子溶液比浓粘度出现负偏离。用高分子溶液流过时间对浓度作图的外推值t0^*重新计算相对粘度，则高分子溶液比浓粘度与浓度之间满足线性关系。不同分子量PEO水溶液流过时间对浓度作图的外推值t0^*是完全一致的。利用纯溶剂在粘度计中流过时间的改变确定了高分子在毛细管管壁上吸附层的厚度，发现PEO在毛细管管壁上吸附层厚度与分子量无关。     

Formation of a supramolecular gel between alpha-cyclodextrin and free and adsorbed PEO on the surface of colloidal silica: effect of temperature, solvent, and particle size

Aqueous solutions of alpha-cyclodextrin (alpha-CD) complex spontaneously with poly(ethylene oxide) (PEO), forming a supramolecular structure known as pseudopolyrotaxane. We have studied the formation of the complex obtained from the threading of alpha-CD onto PEO, both free in solution and adsorbed on colloidal silica. The kinetics of the reaction were studied by gravimetric methods and determined as a function of temperature and solvent composition for the PEO free in solution. PEO was then adsorbed on the surface of colloidal silica particles, and the monomers were displaced by systematically varying the degree of complexation, the concentration of particles, and the molecular weight of the polymer. The effect of the size of the silica particles on the yield of the reaction was also studied. With the adsorbed PEO, the complexation was found to be partial and to take place from the tails of the polymer. The formation of a gel network containing silica at high degrees of complexation was observed. Small-angle X-ray and neutron scattering experiments were performed to study the configuration of the polymeric chains and confirmed the partial desorption of the polymer from the surface of the silica upon complexation.     

Polystyrene‐graft‐poly(ethylene oxide) copolymers prepared by macromonomer technique in dispersion. I. Liquid chromatographic separation of product mixtures

Products of the radical dispersion copolymerization of methacryloyl‐terminated poly(ethylene oxide) (PEO) macromonomer and styrene were separated and characterized by size exclusion chromatography (SEC), full adsorption‐desorption (FAD)/SEC coupling and eluent gradient liquid adsorption chromatography (LAC). In dimethylformamide, which is a good solvent for PEO side chains but a poor solvent for polystyrene (PS), amphiphilic PS‐graft‐PEO copolymers formed aggregates, which were very stable at room temperature even upon substantial dilution. The aggregates disappeared at high temperature or in tetrahydrofuran (THF), which is a good solvent for both homopolymers and for PS‐graft‐PEO. FAD/SEC procedure allowed separation of homo‐PS from graft‐copolymer and determination of both its amount and molar mass. Effective molar mass of graft‐copolymer was estimated directly from the SEC calibration curve determined with PS standards. Presence of larger amount of the homo‐PS in the final graft‐copolymer products was also confirmed with LAC measurements. The results indicate that there are at least two or maybe three polymerization loci; namely the continuous phase, the particle surface layer and the particle core. The graft copolymers are produced mainly in the continuous phase while PS or copolymer rich in styrene units is formed mostly in the core of monomer‐swollen particles. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 2284–2291, 2000     

Composite natural rubber–polychloroprene latex particles produced by the heterocoagulation technique

Composite natural rubber (NR) based latex particles were prepared using the heterocoagulation technique. A nonionic surfactant (Tween 80) whose molecules bear poly(ethylene oxide) (PEO) was adsorbed on polychloroprene (CR) latex particles and allowed to form complexes between PEO and indigenous surfactant (protein–lipid) on the NR particle surface. The heterocoagulated NR/CR–Tween particles produced were characterised by particle size, zeta-potential and glass-transition temperature measurements and the data indicated the presence of CR–Tween on the outer layer of the composite polymer particles. The results agreed well with the better oil resistance of films cast from heterocoagulated latex when compared with that of the NR film. Received: 22 August 2000 Accepted: 8 January 2001     

Buffers to suppress sodium dodecyl sulfate adsorption to polyethylene oxide for protein separation on capillary polymer electrophoresis

Although polyethylene oxide (PEO) offers several advantages as a sieving polymer in SDS capillary polymer electrophoresis (SDS-CPE), solution properties of PEO cause deterioration in the electrophoresis because PEO in solution aggregates itself, degrades into smaller pieces, and forms polymer-micelle complexes with SDS. We examined protein separation on SDS-CPE with PEO as a sieving matrix in four individual buffer solutions: Tris-CHES, Tris-Gly, Tris-Tricine, and Tris-HCl buffers. The solution properties of PEO as a sieving matrix in those buffers were examined by dynamic light scattering (DLS) and by surface tension. Preferential SDS adsorption onto PEO disturbed protein-SDS complexation and impaired the protein separation efficiency. Substantial adsorption of SDS to PEO was particularly observed in Tris-Gly buffer. The Tris-CHES buffer prevented SDS from adsorbing onto the PEO. Only Tris-CHES buffer achieved separation of six proteins. This study demonstrated efficient protein separation on SDS-CPE with PEO.     

温敏梳状嵌段共聚物对PS微球阻抗蛋白吸附作用的研究

采用可逆加成断裂链转移聚合(RAFT)方法和大分子单体技术,制备了温敏性聚N-异丙基丙烯酰胺(PNIPAM)-聚乙烯基吡咯烷酮(PVP)与PNIPAM-聚氧化乙烯(PEO)梳状嵌段共聚物,这些共聚物具有PVP或PEO支链.以溶菌酶为蛋白模型研究了所得共聚物对聚苯乙烯(PS)微球表面蛋白吸附的抑制作用.通过絮凝实验、激光散射法表观粒径测定、电泳迁移率测定及蛋白吸附量的定量数据比较了不同梳状结构的抗蛋白吸附效果.结果表明,预吸附梳状嵌段共聚物可有效阻抗蛋白吸附,亲水支链增加阻抗性能提高,即使环境温度高于PNIPAM的相转变温度也能阻抗蛋白吸附.透射电镜和共聚物胶体粒径测试表明,梳状嵌段共聚物阻抗蛋白吸附的机制是预吸附后PVP或PEO亲水支链在微球表面形成了阻隔层.通过PS微球的变温絮凝实验可评价预吸附聚合物的抗蛋白吸附性能,快速获得定性结果.     

Particle-induced phase separation in mixed polymer solutions

The influence of added colloidal particles on the phase separation of mixed aqueous polymer solutions is investigated. Two types of particles (polystyrene latex or silica) and different combinations of segregating polymers (dextran of varying molar mass combined with poly(ethylene oxide) (PEO) of varying molar mass, or Ucon, a copolymer of ethylene oxide and propylene oxide) were used. All systems displayed particle-induced instability effects, but the extent of the effect varied strongly between the various combinations and with the amount of added salt. Very large instability effects were seen in certain mixtures. Two mechanisms, both relying on the adsorption of at least one of the polymers to the particle surface, seem to operate. Close to the cloud-point curve of the particle-free polymer1/polymer2/water mixture, adsorption of PEO or Ucon to the particles gives rise to a capillary-induced phase separation. Close to the dextran/water axis of the phase diagram, the adsorbing polymer gives rise to a surface modification of the particles, which then interacts repulsively with the surrounding dextran solution.     

Inverse gas chromatographic characterization of triblock copolymer of polystyrene–poly(ethylene oxide)–polystyrene

The thermodynamic properties of triblock copolymer of polystyrene–poly (ethylene oxide)–polystyrene (PS‐b‐PEO‐b‐PS) were investigated by means of inverse gas chromatography (IGC) using 15 different kinds of solvents as the probes. Some thermodynamic parameters, such as specific retention volume, molar heats of sorption, weight fraction activity coefficient, Flory‐Huggins interaction parameter, partial molar heats of mixing and solubility parameter were obtained to judge the interactions between PS‐b‐PEO‐b‐PS polymers and solvents and the solubility of the polymers in these solvents. It was found that increasing PEO content in PS‐b‐PEO‐b‐PS resulted in the increase in the solubility of PS‐b‐PEO‐b‐PS in alkanes and acetates solvents, but the solubility in alcohols had no change, and more PEO content in polymer caused a small decrease in the solubility parameter of PS‐b‐PEO‐b‐PS polymer, © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 2015–2022, 2007     

悬浮-乳液复合聚合聚苯乙烯-聚甲基丙烯酸甲酯复合粒子的颗粒特性和成粒机理

采用在苯乙烯 (St)悬浮聚合过程中滴加甲基丙烯酸甲酯 (MMA)乳液聚合组分的悬浮 乳液复合聚合方法 ,制备大粒径聚苯乙烯 聚甲基丙烯酸甲酯 (PS PMMA)复合粒子 .研究聚合物粒径分布和颗粒形态的变化发现 ,在St悬浮反应中期滴加MMA乳液聚合组分后 ,聚合体系逐渐由悬浮粒子与乳胶粒子并存向形成单峰分布复合粒子转变 ,最终形成核 壳结构完整的大粒径PS PMMA复合粒子 ;在St悬浮反应初期滴加MMA乳液聚合组分 ,St与MMA一起分散成更小液滴 ,反应后期凝并成非核 壳结构复合粒子 ;在St悬浮反应后期滴加MMA乳液聚合组分 ,PMMA乳胶粒子与PS悬浮粒子基本独立存在 .根据以上结果 ,提出了St MMA悬浮 乳液复合聚合的成粒机理 .     

Role of adsorbed chain rigidity in reinforcement of polymer nanocomposites

The thermomechanical behavior of polymer nanocomposites is mostly governed by interfacial properties which rely on particle–polymer interactions, particle loading, and dispersion state. We recently showed that poly(methyl methacrylate) (PMMA) adsorbed nanoparticles in poly(ethylene oxide) (PEO) matrices displayed an unusual thermal stiffening response. The molecular origin of this unique stiffening behavior resulted from the enhanced PEO mobility within glassy PMMA chains adsorbed on nanoparticles. In addition, dynamic asymmetry and chemical heterogeneities existing in the interfacial layers around particles were shown to improve the reinforcement of composites as a result of good interchain mixing. Here, the role of chain rigidity in this interfacially controlled reinforcement in PEO composites is investigated. We show that particles adsorbed with less rigid polymers improve the mechanical properties of composites. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2019 , 57, 9–14     

Preparation of poly(ethylene oxide) star polymers and poly(ethylene oxide)–polystyrene heteroarm star polymers by atom transfer radical polymerization

Poly(ethylene oxide) (PEO) star polymer with a microgel core was prepared by atom transfer radical poylmerization (ATRP) of divinyl benzene (DVB) with mono‐2‐bromoisobutyryl PEO ester as a macroinitiator. Several factors, such as the feed ratio of DVB to the initiator, type of catalysts, and purity of DVB, play important roles during star formation. The crosslinked poly(divinyl benzene) (PDVB) core was further obtained by the hydrolysis of PEO star to remove PEO arms. Size exclusion chromatography (SEC) traces revealed the bare core has a broad molecular weight distribution. PEO–polystyrene (PS) heteroarm star polymer was synthesized through grafting PS from the core of PEO star by another ATRP of styrene (St) because of the presence of initiating groups in the core inherited from PEO star. Characterizations by SEC, ¹H NMR, and DSC revealed the successful preparation of the target star copolymers. Scanning electron microscopy images suggested that PEO–PS heteroarm star can form spherical micelles in water/tetrahydrofuran mixture solvents, which further demonstrated the amphiphilic nature of the star polymer. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 2263–2271, 2004     

Physicochemical studies on hydrophobic PEO‐PPO‐PEO triblock copolymer micelles in SDS micellar environment

The shape, size, aggregation, hydration, and correlation times of water insoluble PEO‐PPO‐PEO triblock copolymer micelles with sodium dodecylsulfate (SDS) micelles were investigated using transport studies and dynamic light scattering technique. From the conductance of micellar solutions of the polymer in 25 mM SDS and 5 mM NaCl, the hydration of polymer micelles were determined using the principle of obstruction of electrolyte migration by the polymer. The asymmetry of the micellar particles of polymer and polymer‐SDS mixed micellar systems in 5 mM NaCl and their average axial ratios were calculated using intrinsic viscosity and hydration data obeying Simha–Einstein equation. Hydration number and micellar sizes were variable with temperature. The shape of the polymer micelles has been ellipsoidal rather than spherical. The micellar volume, hydrodynamic radius, radius of gyration, diffusional coefficients as well as translational, rotational and effective correlation times have been calculated from the absolute values of the axes. The partial molal volume of polymer micelles has also been determined and its comparison with the molar volume of pure polymer suggested a volume contraction due to immobilization of the water phase by the hydrophilic head groups of the polymer. The thermodynamic activation parameters for viscous flow favor a more ordered water structure around polymer micelles at higher temperatures. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 2410–2420, 2007     

两亲性杂侧链聚合物刷的合成及其乳化功能

报道了一种随机高密度接枝亲水、疏水聚合物侧链的刷形两亲性聚合物.首先,结合可逆加成-断裂链转移(RAFT)聚合和后修饰方法,得到含叠氮侧基的聚甲基丙烯酸缩水甘油酯(PGMA-N3)作为主链;再分别合成端炔基聚苯乙烯(PS)和端炔基聚环氧乙烷(PEO),然后通过铜催化的叠氮-炔环加成反应,将疏水性PS和亲水性PEO同时高效的接到PGMA主链上,制得两亲性杂侧链的聚合物刷.由凝胶渗透色谱(SEC)分析得知,在主链叠氮基团与两侧链总炔基的摩尔投料比为1∶1的条件下,PS和PEO的接枝效率很高,都大于90%.通过调节主链长度和2种侧链的投料比,获得不同组成的聚合物刷.通过等质量的甲苯/水混合体系,考察两亲性聚合物刷的乳化能力,发现主链聚合度为100,PS∶PEO比例为70∶30的聚合物刷表现出最佳的乳化性能.     

A new strategy for optimizing sensitivity, speed, and resolution in capillary electrophoretic separation of DNA

DNA separations were performed in poly(ethylene oxide) (PEO) solutions prepared in 100 mM Tris-boric acid (TB) buffers using a capillary filled with TB buffers with concentrations up to 2.5 M, pH 10.0. The electroosmotic flow (EOF) increased with increasing the concentration of TB buffers till 1.5 M as a result of decreasing PEO adsorption on the capillary wall. At high TB concentrations (> 1.5 M), the peaks corresponding to small DNA fragments (11 and 8 base pairs) became sharper and were detected. Relative standard deviations of the EOF coefficient and the migration times of the DNA fragments were all less than 1% using a capillary filled with TB buffers at concentrations higher than 1.5 M. When separations were performed at different pH values of PEO solutions and TB buffers, better results in terms of sensitivity, speed, and resolution were generally achieved. The fluorescence intensity of the 2176 bp fragment obtained at pH values of TB buffers/PEO solutions 10.0/8.2 was 27-fold of that at pH values 8.2/8.2. The enhancement was related to effects of pH and borate on fluorescence intensity, DNA conformation, stacking, and interactions with the capillary wall. Using a capillary filled with 400 mM TB buffers, pH 10.0, the separation of DNA (pBR 322/HaeIII digest, pBR 328/Bg/I digest and pBR 328/HinfI digest) in 1.5% PEO solutions prepared in 100 mM TB buffers, pH 9.0, at 375 V/cm was accomplished in less than 18 min.