Ⅱ—Ⅵ族稀磁半导体ZnSe／Zn1—xMnxSe超晶格中的应力效应

本文通过Ⅱ－Ⅵ族稀磁半导体超晶格ＺｎＳｅ／Ｚｎ１－ｘＭｎｘＳｅ的光致发光谱的测量，对其应力效应进行了讨论。样品的组分ｘ＝０．２，０．３，０．４，测量温度为Ｔ＝１１￣３００Ｋ。结果表明：由于应力效应，ＺｎＳｅ／Ｚｎ１－ｘＭｎｘＳｅ超晶格中的激子能量随ｘ值增加而发生红移。在相同组分下，不同阱、垒宽度比使应力的分布产生明显变化，从而影响超晶格中激子能量。实验与理论计算结果相一致。超晶格中光致发光峰随温度     

Bi2Sr2Ca(Cu1-xMnx)2Oy单晶的结构与超导电性

用自助熔剂法制备了Ｂｉ２Ｓｒ２Ｃａ（Ｃｕ１－ｘＭｎｘ）２Ｏｙ（ｘ＝０．０１,０．０５,０．０８,０．１０）单晶。单晶的ｃ轴长度随Ｍｎ含量的增加而减小。Ｒ－Ｔ曲线测量表明,零电阻温度Ｔｃ随ｘ的增大面逐渐下降。对Ｍｎ掺杂量较高的一些单晶,发现其Ｒ－Ｔ曲线在１０５Ｋ左右有一陡降,表明Ｍｎ掺杂量较高的单晶中可能有微量的Ｂｉ２２２３相成分存在。     

稀磁半导体Zn1—xMnxSe外延膜的反射的光致发光谱

测量了用热壁外延（ＨＷＥ）生长的不同组分（０≤ｘ≤０．９８）的Ｚｎ１－ｘＭｎｘＳｅ薄膜在温度为３００Ｋ下的反射光谱，用Ｘ射线能谱测定样品实际的组分ｘ值，由此获得了其能隙Ｅｇ与组分ｘ的关系：在０〈ｘ〈０．２组分范围，Ｅｇ随ｘ的变化显示了反常现象，当ｘ〉０．２时，能隙Ｅｇ随ｘ线性增大。在室温和低温下测量了样品的光致发光，除观测到Ｍｎ＾２＋离子内部４Ｔ１→６Ａ１发光峰外，在其低能边观测到一个较宽的发光峰     

ZnCdse－ZnSe多量子阱中的激子发光

在７７－３００Ｋ温度下研究了Ｚｎ（１－ｘ）ＣｄｘＳｅ－ＺｎＳｅ多量子阱（ＭＱＷｓ）的光致发光特性．首次在７７Ｋ，Ａｒ离子激光器的４５７．９ｎｍ激发下，在Ｚｎ（０．６８）Ｃｄ（０．３２）Ｓｅ－ＺｎｓｅＭＱＷｓ中观测到５个发光带，其中三个发光带被归因于不同的激子发射：即ｎ＝１重空穴（ＨＨ）激子；ｎ＝ｌ轻－重空穴（ＬＨ）激子和ｎ＝ＩＨＨ激子同时发射两个纵光学声子的复合发光，并且，；ｎ＝１ＨＨ激子发光可延续至室温．     

稀磁半导体Zn_（1－x）Mn_xSe外延膜的反射和光致发光谱

测量了用热壁外延（ＨＷＥ）生长的不同组分（０≤ｘ≤０．９８）的Ｚｎ１－ｘＭｎｘＳｅ薄膜在温度为３００Ｋ下的反射光谱，用Ｘ射线能借测定样品实际的组分ｘ值，由此获得了其能隙Ｅｇ与组分ｘ的关系：在Ｏ＜Ｘ＜０．２组分范围，Ｅｇ随ｘ的变化显示了反常现象，当Ｘ＞０．２时，能隙Ｅｇ随ｘ线性增大。在室温和低温下测量了样品的光致发光，除观测到Ｍｎ２＋离子内部４Ｔ１→６Ａ１发光峰外，在其低能边观测到一个较宽的发光峰，对结果进行了分析讨论。     

〔（NH_4）_xK_（1－x）〕_2SnCl_6混晶的喇曼散射研究

本文用喇曼散射的方法研究了六氯锡化钾铵混晶系列样品［（ＮＮ_４）_ｘＫ_（１－ｘ）］_２ＳｎＣｌ_５（ｘ＝０，０．０５，０．１，０．１５，０．２，０．２５，０，３，１）从室温到７７Ｋ的行为，首先观察到了其外振动模的双模行为，并且还发现了其一内模Ｔ_（２ｇｉｎｔ）的宽度随铵离子浓度ｘ的增加而增加，相变温度Ｔｃ却随铵离子浓度的增加而迅速下降，下降速率约为ｄＴ_ｃ／ｄｘ＝－６００Ｋ／ｍｏｌ，这一行为是由于正四面体的ＮＨ_４￣＋离子对正八面体的ＳｎＣｌ_６￣（２－）离子团的转动产生阻碍而引起。内模Ｔ_（２ｇｉｎｔ）的宽度变化也是由于铵离子的转动影响以及由它引起的晶格畸变所导致。双模行为来自于强烈的集团效应。     

Zn1—xMnx／ZnSe应变超晶格分子束外延生长及光学特性研究

用分子束外延方法在ＧａＡｓ（１００）衬底上成功生长了高质量的Ｚｎ１－ｘＭｎｘＳｅ／ＺｎＳｅ（ｘ＝０．１６），超晶格结构，用Ｘ射线衍射和低温光致发光（ＰＬ）对其结构，应变分布以及光学性能进行了研究，结果表明，２Ｋ温度下，Ｚｎ１－ｘＭｎｘＳｅ／ＺｎＳｅ超晶格的光致发光中主发光峰对应于ＺｎＳｅ阱中基态电子和基态轻空穴之间的自由激子跃迁，而且其峰位相对于ＺｎＳｅ薄膜材料的自由激子峰有明显移动。其中，当超晶     

Nd_(1-x)Ba_xMnO_3和La_(0.67)Mg_(0.33)Mn_(0.85)M_(0.15)O_3(M=Mn,Ga,Fe)中Mn位自旋磁矩对电导性的影响

研究了Ｎｄ１－ｘＢａｘＭｎＯ３和Ｌａ０．６７Ｍｇ０．３３Ｍｎ０．８５Ｍ０．１５Ｏ３（Ｍ＝Ｍｎ，Ｇａ，Ｆｅ）的导电性，发现Ｍｎ位的自旋磁矩排列状态和大小对体系的导电性有强烈的影响．在Ｎｄ１－ｘＢａｘＭｎＯ３中，当Ｍｎ３＋／Ｍｎ４＋的浓度比值为２∶１，１∶１，１∶２时，电阻率出现半导体－金属转变．推论该类体系的导电性首先由体系中Ｍｎ３＋和Ｍｎ４＋自旋磁矩形成的磁结构状态决定，然后才取决于由Ｂａ掺杂浓度所决定的载流子浓度．在Ｌａ０．６７Ｍｇ０．３３Ｍｎ０．８５Ｍ０．１５Ｏ３（Ｍ＝Ｍｎ，Ｇａ，Ｆｅ）中，Ｍｎ位自旋磁矩大小的改变对导电性有强烈的影响，另外发现该类体系均以变程跳跃模式进行导电．     

Nd1—xBaxMnO3和La0.67Mg0.33Mn0.85M0.15O3（M=Mn,Ga,Fe）中Mn？…

研究了Ｎｄ１－ｘＢａｘＭｎＯ３和Ｌａ０．６７Ｍｇ０．３３Ｍｎ０．８５Ｍ０．１５Ｏ３的导电性，发现Ｍｎ位的自旋磁矩排列状态一大小 和对体系的导电性有强烈的影响，在Ｎｄ１－ｘＢａｘＭｎＯ３中，当Ｍｎ＾３＋／Ｍｎ＾４－的浓度比值为２：１．１：１，１：２时，电阻率出现半导体－金属转变，推论该类体系的导电性首先由体系中Ｍｎ＾３＋和Ｍｎ＾４＋自旋磁矩形的磁结构状态决定，然后才取决于由Ｂａ掇杂浓度所决定的载流子     

Bi_2Sr_（1．8）La_（0．2）Cu_（1－x）MxOy（M＝Ni，Z

本文利用Ｘ射线衍射、电子衍射和拉曼散射对Ｂｉ２Ｓｒ１．８Ｌａ０．２ＣＵ１－ｘＭｘＯｙ（Ｍ＝Ｎｉ，Ｚｎ）体系的微结构进行了研究．实验表明，随着掺杂量的增加，掺Ｚｎ体系的结构畸变明显大于掺Ｎｉ体系的结构畸变．由此看来，非磁性杂质Ｚｎ之所以比磁性杂质Ｎｉ对Ｔｃ具有更大的抑制作用，应该归因于Ｚｎ掺杂造成材料中严重的结构畸变．     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.     

A stereo matching algorithm using multi-peak candidate matches and geometric constraints

Gray cross correlation matching technique is adopted to extract candidate matches with gray cross correla- tion coefficients less than some certain range of maximal correlation coefficient called multi-peak candidate matches. Multi-peak candidates are extracted corresponding to three closest feature points at first. The corresponding multi-peak candidate matches are used to construct the model polygon. Correspondence is determined based on the local geometric relations between the three feature points and the multi-peak candidates. The disparity test and the global consistency checkout are applied to eliminate the remaining ambiguous matches that are not removed by the local geometric relational test. Experimental results show that the proposed algorithm is feasible and accurate.