Critical current density in MgB2 bulk samples after co-doping with nano-SiC and poly zinc acrylate complexes

The co-doped MgB₂ bulk samples have been synthesized using an in situ reaction processing. The additives is 8 wt.% SiC nano powders and 10 wt.% [(CH₂CHCOO)₂Zn]_n poly zinc acrylate complexes (PZA). A systematic study was performed on samples doped with SiC or PZA and samples co-doped with both of them. The effects of doping and co-doping on phase formation, microstructure, and the variation of lattice parameters were studied. The amount of substituted carbon, the critical temperature (T_c) and the critical current density (J_c) were determined. The calculated lattice parameters show the decrease of the a-axis, while no obvious change was detected for c-axis parameter in co-doped samples. This indicates that the carbon was substituted by boron in MgB₂. The amount of substituted carbon for the co-doped sample shows an enhancement compared to that of the both single doped samples. The co-doped samples perform the highest J_c values, which reaches 3.3 × 10⁴ A/cm² at 5 K and 7 T. It is shown that co-doping with SiC and organic compound is an effective way to further improve the superconducting properties of MgB₂.     

Synthesis and characterization of excess magnesium MgB2 superconductor under inert carbon environment

The structural, transport and magnetic properties of MgB₂ superconductor heavily blended with Mg is studied. The samples are synthesized with a new approach in both, pressed carbon environment and in flowing argon. The excess magnesium used is observed to play dual role: one being the prevention of Mg losses during the synthesis process and hence maintaining the stoichiometry of MgB₂ phase, and second being the formation of Mg milieu probably all around the MgB₂ grains to give a dense structure. Excess Mg also improves the grain connectivity by going into the pores and there by minimizing the insulating junctions. The residual resistivity of the sample is observed to decrease from 57.02 μΩ cm to 10.042 μΩ cm as it is progressively filled with superconductor–normal–superconductor (SNS) type junctions amongst the grains by the virtue of increased magnesium content. The synthesized samples devoid of porosity show the superconducting transition, T_c in the range of 39–34 K as of clean MgB₂ samples, though overloaded with Mg. The excess Mg resulted in enhanced critical current density, J_c from 6.8 × 10³ A cm^?2 to 5.9 × 10⁴ A cm^?2 at 20 K and 10 kOe, with reasonable decrease in the superconducting transition. Thus our samples being overloaded with Mg impart mechanical strength and competitive superconducting properties, which forms a part of interest.     

Luminescence behaviour of beryl (aquamarine variety) from Turkey

Natural blue-green beryl from Turkey has been investigated using scanning electron microscopy-energy-dispersive spectroscopy (SEM-EDS), X-ray diffraction (XRD) and Cathodoluminescence (CL). Beryl has the chemical formula Be₃Al₂Si₆O₁₈ and is hexagonal with space group P6/mcc. Chemical analyses of the beryl sample utilised inductively coupled plasma-atomic emission spectroscopy (ICP-AES) for major oxides and trace elements. It shows that the beryl sample is rich in Cs (531 ppm) and contains low concentrations of transition-metal ions, in total 2.29 wt.% Fe, 269 ppm Mn, V<5 ppm and Cr 20 ppm. Ideas on the origin of the green colour of this mineral are presented. The CL spectrum of the bulk sample display intense broad band emission from ～360 to ～800 nm.     

Fabrication of Ti doped MgB2/Cu superconducting wires by SHS method in an unsealed furnace

Mg_0.9Ti_0.1B₂/Cu wires have been successfully synthesized by the powder-in-tube (PIT) technique combined with the self-propagating high-temperature synthesis (SHS) method in an unsealed furnace. The analysis includes the studies of the sample microstructure, phase composition, critical transition temperature T_c and critical current density J_c. The experiments show that the PIT technique combined with the SHS method is effective in reducing the Mg volatilization and oxidation. There is little reaction between Mg and Cu in the SHS process, but with the MgCu₂ and CuO phases, the reaction does occur in the inner sheath wall of the copper tube. The findings also indicate that there is little MgO in the sample. The sample has a very strong flux pinning ability at the low magnetic fields since the TiB₂ phase may prevent the growth of MgB₂ grains and lead to a favorable effect on grain refinement. The wires exhibit a high critical current density, e.g. 2.7 × 10⁵ A/cm² in the 1.0 T field at 4.2 K and 1.3 × 10⁵ A/cm² in the 2.0 T field at 4.2 K.     

Influence of Zr and Ce doping on electromagnetic properties of (Gd,Y)–Ba–Cu–O superconducting tapes fabricated by metal organic chemical vapor deposition

(Gd,Y)Ba₂Cu₃O_x tapes have been fabricated by metal organic chemical vapor deposition (MOCVD) with Zr-doping levels of 0–15 mol.% and Ce doping levels of 0–10 mol.% in 0.4 μm thick films. The critical current density (J_c) of Zr-doped samples at 77 K, 1 T applied in the orientation of H 6 c is found to increase with Zr content and shows a maximum at 7.5% Zr doping. The 7.5% Zr-doped sample exhibits a critical current density (J_c) of 0.95 MA/cm² at H 6 c which is more than 70% higher than the J_c of the undoped sample. The peak in J_c at H 6 c is 83% of that at H 6 a–b in the 7.5% Zr-doped sample which is more than twice as that in the undoped sample. Superconducting transition temperature (T_c) values as high as about 89 K have been achieved in samples even with 15% Zr and 10% Ce. Ce-doped samples with and without Ba compensation are found to exhibit substantially different J_c values as well as angular dependence characteristics.     

Inelastic neutron scattering on iron-based superconductor BaFe2(As,P)2

Inelastic neutron scattering has been performed on powder sample of an iron-based superconductor BaFe₂(As_0.65P_0.35)₂ with superconducting transition temperature (T_c) = 30 K, whose superconducting (SC) order parameter is expected to have line node. In the normal state, constant-E scan of dynamical structure factor, S(Q, E), exhibits a peak structure centered at momentum transfer Q ～ 1.20 Å^?1, corresponding to antiferromagnetic wave vector. Below T_c, the redistribution of the magnetic spectral weight takes place, resulting in the formation of a peak at E ～ 12 meV and a gap below 6 meV. The enhanced magnetic peak structure is ascribed to the spin resonance mode, evidencing sign change in the SC order parameter similar to other iron-based high-T_c superconductors. It suggests that fully-gapped s_± symmetry dominates in this superconductor, which gives rise to high-T_c (=30 K) despite the nodal symmetry.     

Pinning,thermally activated depinning and their importance for tuning the nanoprecipitate size and density in high Jc YBa2Cu3O7−x films

YBa₂Cu₃O_7?x (Y123) films with quantitatively controlled artificial nanoprecipitate pinning centers were grown by pulsed laser deposition (PLD) and characterized by transport over wide temperature (T) and magnetic field (H) ranges and by transmission electron microscopy (TEM). The critical current density J_c was found to be determined by the interplay of strong vortex pinning and thermally activated depinning (TAD), which together produced a non-monotonic dependence of J_c on c-axis pin spacing d_c. At low T and H, J_c increased with decreasing d_c, reaching the very high J_c ～ 48 MA/cm² ～20% of the depairing current density J_d at 10 K, self-field and d_c ～ 10 nm, but at higher T and H when TAD effects become significant, J_c was optimized at larger d_c because longer vortex segments confined between nanoprecipitates are less prone to thermal fluctuations. We conclude that precipitates should extend at least several coherence lengths along vortices in order to produce irreversibility fields H_irr(77 K) greater than 7 T and maximum bulk pinning forces F_p,max(77 K) greater than 7–8 GN/m³ (values appropriate for H parallel to the c-axis). Our results show that there is no universal pin array that optimizes J_c at all T and H.     

Effect of W-addition on pinning property of MgB2

The 5d transition metal W was added into the MgB₂ superconductor. The Mg, B and W were sintered at 1173 K for 30 min under H₂/Ar atmosphere in the electric furnace. The W_x(MgB₂)_1?x samples were prepared in the W concentration range of 0 ? x ? 0.05. Temperature and field dependences of magnetization were measured by the SQUID magneto-meter. The field and x dependences of J_c at 20 K were analyzed by the extended critical state model. The enhancement of J_c became maximum for the x = 0.02 sample.     

Effect of processing temperature on the superconducting properties of acetone doped MgB2 tapes

Correlation of phase formation, critical transition temperature T_c, microstructure, and critical current density J_c with sintering temperature has been studied for acetone doped MgB₂/Fe tapes. Sintering was performed at 600–850 °C for 1 h in a flowing Ar atmosphere. High boron substitution by carbon was obtained with increasing the sintering temperature; however, the acetone doped samples synthesized at 800 °C contain large size MgB₂ grains and more MgO impurities. Incomplete reaction for the acetone doped samples heated at 600 °C result in bad intergrain connectivity. At 4.2 K, the best J_c value was achieved in the acetone doped sample sintered at 700 °C, which reached 24,000 A/cm² at 10 T and 10,000 A/cm² at 12 T, respectively. Our results indicate that the small grain size and less impurity were also important for the improvement of J_c–B properties besides the substitutions of B by C.     

Strongly enhanced flux pining of GdBCO coated conductors with BaSnO3 nanorods by pulsed laser deposition

We report the effects of BSO addition on the crystallinity, texture, and the field dependency of critical current density (J_c) of GdBCO coated conductors (CCs) prepared by pulsed laser deposition (PLD). Undoped and BSO-doped GdBCO films showed only c-axis oriented growth, and the incorporated BSO nanorods exhibited epitaxial relationship with the GdBCO matrix. In comparison with undoped film, BSO-doped GdBCO film exhibited greatly enhanced J_c and higher pinning force densities in the entire field region of 0–5 T (H//c) at 77 and 65 K. The BSO-doped GdBCO film showed the maximum pinning force densities (F_p) of 6.5 GN/m³ (77 K, H//c) and 32.5 GN/m³ (65 K, H//c), ～2.8 times higher than those of the undoped sample. Cross-sectional TEM analyses exhibited nano-structured BSO nanorods roughly aligned along the c-axis of the GdBCO film, which are believed effective flux pinning centers responsible for strongly improved critical current densities in magnetic fields.     

Long RE123 coated conductors with high critical current over 500 A/cm by IBAD/PLD technique

We have developed long RE₁Ba₂Cu₃O_7?X (RE123) coated conductors with large current capacity by the ion beam assisted deposition (IBAD) and the pulsed laser deposition using hot wall heating (HW-PLD) technique. As a result, we could fabricate an 8 m-long Gd₁Ba₂Cu₃O_7?X (Gd123) coated wire with the minimum and maximum critical current (I_c) of 951 A/cm-w and 1003 A/cm-w at 77 K, 0 T, respectively, measured in 0.7 m-long sections by the standard 4-probe technique. Furthermore, we succeeded in preparation of over 600 m-long Gd123 coated wire with the uniform I_c distribution over 600 A/cm-w. It had average, maximum and minimum I_c of 665, 698, 609 A/cm-w, respectively. The n-values of the sample showed the maximum I_c and minimum I_c were 40 and 36, respectively. As a result, we set the new world record of I_c × L value as 374535 A m (= 609 A × 615 m). The in-field performance of this long wire was quite high as well; the minimum I_c exceeded 50 A/cm-w at 77 K, 3 T.     

Homoepitaxial growth of MOD-YBCO thick films on evaporated and MOD templates

We have prepared metal organic deposition (MOD)-YBCO thick films by repeating the coating-pyrolysis-crystallization procedure onto ～100-nm-thick evaporated and MOD templates. Surface morphology of the template was found to strongly affect the homoepitaxial growth of MOD-YBCO layers on the template; namely, the epitaxial growth of MOD-YBCO on the evaporated template was much easier than that on the MOD template. A 220-nm-thick epitaxial MOD-YBCO film was successfully prepared on the 100-nm-thick evaporated-YBCO template to obtain a 320-nm-thick YBCO film, which exhibited J_c = 2.44 MA/cm² and I_c = 78 A/cm. The I_c value has significantly increased from 37 A/cm for the evaporated-template.     

Intrinsic pinning properties of FeSe0.5Te0.5

The intrinsic pinning properties of FeSe_0.5Te_0.5, which is a superconductor with a critical temperature T_c of approximately 14 K, were studied through the analysis of magnetization curves obtained using an extended critical state model. For the magnetization measurements carried out with a superconducting quantum interference device (SQUID), external magnetic fields were applied parallel and perpendicular to the c-axis of the sample. The critical current density J_c under the perpendicular magnetic field of 1 T was estimated using the Kimishima model to be equal to approximately 1.6 × 10⁴, 8.8 × 10³, 4.1 × 10³, and 1.5 × 10³ A/cm² at 5, 7, 9, and 11 K, respectively. Furthermore, the temperature dependence of J_c was fitted to the exponential law of J_c(0) × exp(?αT/T_c) up to 9 K and the power law of J_c(0) × (1 ? T/T_c)ⁿ near T_c.     

Contact resistance of multi-walled carbon nanotube/natural rubber nanocomposites with metallic ball

This paper reports on the contact resistance (R_c) between carbon filler/natural rubber (NR) nanocomposite and gold ball: three varieties of nanocomposites were prepared from carbon black (CB) and two kinds of multi-walled carbon nanotubes (MWCNTs) with different diameter. R_c of MWCNT/NR nanocomposite was remarkably less than that of CB/NR nanocomposites. The relationship between R_c of MWCNT/NR nanocomposites and applied load was expressed in the formula, R_c=C·P⁻ⁿ (P: load, C and n: constant): for the MWCNTs (diameters of 13 nm)/NR and MWCNTs (diameters of 67 nm)/ NR nanocomposites, they were expressed as R_c=1724·P^−0.6 and R_c=344·P^−0.37, respectively. The former (MWCNT, ϕ13 nm) showed higher R_c than the latter (MWCNT, ϕ67 nm) over whole region of applied load. The mechanical hardness of the former was higher (90 HsA) than that of the latter (82 HsA). Therefore, the smaller contact area between the nanocomposite and gold ball of the former resulted in higher R_c. The apparent specific contact resistivity was calculated from the observed values of R_c and contact area: 130 Ω mm² and 127 Ω mm² for the former (MWCNT, ϕ13 nm) and the latter (MWCNT, ϕ67 nm), respectively.     

Aqueous polymer–nitrate solution deposition of YBCO films

High critical current density YBa₂Cu₃O_7?x (YBCO) films were prepared by solution deposition of aqueous non-fluorine precursors. Non-fluorine polymer-assisted deposition (PAD) processes utilizing rheology modifiers and chelating agents were used to produce 50 nm films with a critical current density (J_c) over 3 MA/cm² and 400 nm films with J_c > 1 MA/cm²_. T_c measurements indicated that films have T_c values near 90 K. The total heat treatment time to produce these high performance films was less than 4 h. Rheology modifiers such as polyvinyl alcohol (PVA) and hydroxyethyl cellulose (HEC) were used to increase the thickness of deposited films independent of the solution cation concentration. Chelating agents such as polyethylene glycol (PEG) and sucrose increased the barium ion solubility. Nitrate crystallization during deposition was controlled through rapid drying with vacuum and coating with hot solutions.     

Point-contact Andreev-reflection spectroscopy in ReFeAsO1−xFx (Re = La,Sm): Possible evidence for two nodeless gaps

A deep understanding of the character of superconductivity in the recently discovered Fe-based oxypnictides ReFeAsO_1?xF_x (Re = rare-earth) necessarily requires the determination of the number of the gaps and their symmetry in k space, which are fundamental ingredients of any model for the pairing mechanism in these new superconductors. In the present paper, we show that point-contact Andreev-reflection spectroscopy experiments performed on LaFeAsO_1?xF_x (La-1111) polycrystals with T_c ～ 27 K and SmFeAsO_0.8F_0.2 (Sm-1111) polycrystals with T_c ～ 53 K gave differential conductance curves exhibiting two peaks at low bias and two additional structures (peaks or shoulders) at higher bias voltages, an experimental situation quite similar to that observed by the same technique in pure and doped MgB₂. The single-band Blonder–Tinkham–Klapwijk model is totally unable to properly fit the conductance curves, while the two-gap one accounts remarkably well for the shape of the whole experimental dI/dV vs. V curves. These results give direct evidence of two nodeless gaps in the superconducting state of ReFeAsO_1?xF_x (Re = La, Sm): a small gap, Δ₁, smaller than the BCS value (2Δ₁/k_BT_c ～ 2.2–3.2) and a much larger gap Δ₂ which gives a ratio 2Δ₂/k_BT_c ～ 6.5–9.0. In Sm-1111 both gaps close at the same temperature, very similar to the bulk T_c, and follow a BCS-like behaviour, while in La-1111 the situation is more complex, the temperature dependence of the gaps showing remarkable deviations from the BCS behaviour at T close to T_c.The normal-state conductance reproducibly shows an unusual, but different, shape in La-1111 and Sm-1111 with a depression or a hump at zero bias, respectively. These structures survive in the normal state up to T¹ ～ 140 K, close to the temperatures at which structural and magnetic transitions occur in the parent, undoped compound.     

Effects on Jc of pinning center morphology for multiple-in-line-damage in coated conductor and bulk,melt-textured HTS

The properties of discontinuous aligned pinning centers (PCs) created by high-energy heavy-ions are compared for bulk melt-textured and coated conductor HTS. Properties of PCs, which increase J_c (pinning potential and entanglement), and negative properties which decrease J_c (e.g., decreased T_c and percolation paths) are evaluated. Mechanisms are proposed to explain the very large increases in J_c resulting from multiple-in-line-damage (MILD) compared to continuous columnar pinning centers (CCPC). In particular, a mechanism which results in fluxoid entanglement, even for parallel (unsplayed) PCs, is discussed. The same mechanism is found to also account for restoration of much of the pinning potential expected to be lost due to the gaps in MILD PCs. It also accounts for the fact that at high fluence, J_c increases as fluence is increased, instead of decreasing as expected. The very low self-field in coated conductor permits separation of the negative and positive effects of PCs. It is found that parameters developed to quantify the negative effects in bulk melt-textured YBCO, by 63 GeV U²³⁸ ions, successfully describe damage to 2.1 μm thick coated conductor by 1 GeV Ru⁴⁴ ions. Coated conductor at 77 K and self-field is generally known to have J_c about 100 times that of melt-textured YBCO. However, at 77 K and applied field of 1 T, when both forms of HTS are processed with comparable numbers of near-optimum MILD PCs, the difference in J_c is reduced to a factor of 1.3–2. Whereas J_c for melt-textured YBCO increased sharply, by a factor of up to 16.8 for high-fluence MILD PCs, J_c in coated conductor increased by a smaller factor of 2.5–3.0. Nevertheless, 2.1 μm thick coated conductor, with near-optimum MILD PCs, exhibits J_c = 543 kA/cm² at 77 K and applied field of 1.0 T, and I_c = 114 A/cm-width of conductor. This is the highest value we find in the literature. The phenomenology developed indicates that for optimum MILD PCs in coated conductor, J_c ～ 700 ± 70 kA/cm² should be achievable at 77 K, 1.0 T.     

Large transport critical currents of powder-in-tube Sr0.6K0.4Fe2As2/Ag superconducting wires and tapes

We report the achievement of transport critical currents in Sr_0.6K_0.4Fe₂As₂ wires and tapes with a T_c = 34 K. The wires and tapes were fabricated through an in situ powder-in-tube process. Silver was used as a chemical addition as well as a sheath material. All the wire and tape samples have shown the ability to transport superconducting current. Critical current density J_c was enhanced upon silver addition, and at 4.2 K, a largest J_c of ～1200 A/cm² (I_c = 9 A) was achieved for 20% silver added tapes, which is the highest in iron-based wires and tapes so far. The J_c is almost field independent between 1 T and 10 T, exhibiting a strong vortex pinning. Such a high transport critical current density is attributed to the weak reaction between the silver sheath and the superconducting core, as well as an improved connectivity between grains. We also identify a weak-link behavior from the apparent drop of J_c at low fields and a hysteretic phenomenon. Finally, we found that compared to Fe, Ta and Nb tubes, Ag was the best sheath material for the fabrication of high-performance 122 type pnictide wires and tapes.     

Thickness dependence of Ic and Jc of LTG-SmBCO coated-conductor on IBAD-MgO tapes

We have reported SmBa₂Cu₃O_y (SmBCO) films on single crystalline substrates prepared by low-temperature growth (LTG) technique. The LTG-SmBCO films showed high critical current densities in magnetic fields compared with conventional SmBCO films prepared by pulsed laser deposition (PLD) method. In this study, to enhance critical current (I_c) in magnetic field, we fabricated thick LTG-SmBCO films on metal substrates with ion-beam assisted deposition (IBAD)-MgO buffer and estimated the I_c and J_c in magnetic fields.All the SmBCO films showed c-axis orientation and cube-on-cube in-plane texture. T_c of the LTG-SmBCO films were 93.1–93.4 K. J_c and I_c of a 0.5 μm-thick SmBCO film were 3.0 MA/cm² and 150 A/cm-width at 77 K in self-field, respectively. Those of a 2.0 μm-thick film were 1.6 MA/cm² and 284 A/cm-width respectively. Although I_c increased with the film thickness increasing up to 2 μm, the I_c tended to be saturated in 300 A/cm-width. From a cross sectional TEM image of the SmBCO film, we recognized a-axis oriented grains and 45° grains and Cu–O precipitates. Because these undesired grains form dead layers, I_c saturated above a certain thickness. We achieved that I_c in magnetic fields of the LTG-SmBCO films with a thickness of 2.0 μm were 88 A/cm-width at 1 T and 28 A/cm-width at 3 T.     

Effect of Boron substitution on the superconductivity of non-oxide perovskite MgCNi3

We report synthesis, structural and magnetic (DC and AC) properties of Boron substituted MgCNi₃ superconductor. A series of polycrystalline bulk samples Mg_1.2C_1.6?xB_xNi₃ (x=0.0, 0.08 and 0.16) is synthesized through standard solid-state reaction route, which are found to crystallize in cubic perovskite structure with space group Pm3m. Rietveld analysis of observed XRD data show that lattice parameters expand from a=3.8106 (4) Å for pure, to 3.8164 (2) Å and 3.8173 (5) Å for 5% and 10% Boron substituted samples respectively. DC magnetization exhibited superconducting transition (T_c) at around 7.3 K for pure sample, and the same decreases slightly with Boron substitution. The lower critical field (H_c1) at 2 K is around 150 Oe for pure sample, which increases slightly with Boron substitution. For pure sample the upper critical field (H_c2) being determined from AC susceptibility measurements is 11.6 kOe and 91.70 kOe with 50% and 90% diamagnetism criteria respectively, which decreases to 5.57 kOe and 42.5 kOe respectively for 10% Boron substituted sample. 10% Boron substitution at Carbon site has decreased both the H_c2 and T_c. On the other hand lower critical field (H_c1) at 2 K is slightly increased from around 150 Oe for pure sample, to 200 Oe for 10% Boron substituted sample. Seemingly, the Carbon site Boron substitution induced disorder though has increased slightly the H_c1 but with simultaneous decrease in superconducting transition temperature (T_c) and upper critical field (H_c2). The high relative proportion of Ni in studied MgCNi₃ suggests that magnetic interactions are important and non-oxide perovskite structure make it interesting.