Electrochromism in Hf-doped WO3

Journal of Solid State Electrochemistry - In the present work, we analyzed the electrochromic behavior of tungsten oxide (WO3) and effect of hafnium (Hf) doping on its performance. The...     

WO3基气敏传感器*

气敏传感器已在生物、化学、航空、军事等领域获得了广泛的应用。鉴于WO₃基气敏传感器是检测H₂S、NO_x、O₃和NH₃等气体最有前景的新型氧化物气敏传感器之一,本文以不同的敏感气体为分类依据系统阐述了近年来WO₃基气敏传感器的研究进展,详细探讨了制备方法及贵金属掺杂对上述各种气体气敏性能的影响,并指出了目前WO₃基气敏传感器在研究过程中存在的问题。     

纳米WO3的制备工艺探讨与结构表征

通过气液反应制备了纳米WO₃光催化剂,并用紫外吸收光谱、粉末X射线衍射(XRD)、透射电子显微镜(TEM)、扫描电子显微镜(SEM)、能量散射谱(EDS)等手段对催化剂进行了表征.讨论了乙二醇加入量和表面活性剂十二烷基苯磺酸钠对催化剂粒度大小和形貌的影响.结果表明:当水和乙二醇的比例为25:75时所得WO₃粒径为30 nm左右.在此比例条件下加入0.1 g表面活性剂十二烷基苯磺酸钠,可制得片状WO₃,粒径约为80 nm.对自制的两种纳米WO₃光催化剂在紫外光照射时降解苯酚的活性进行了初步探讨,两者的催化性能均明显优于商品WO₃.     

Highly sensitive WO3 hollow-sphere gas sensors

In this paper, we describe how WO(3) hollow spheres have been synthesized in solution phase by the controlled hydrolysis of WCl(6) using novel carbon microspheres as the templates. All of the products were characterized by X-ray powder diffraction (XRD), scanning electronic microscopy (SEM), and transmission electron microscopy (TEM). The as-synthesized spheres had large diameters of about 400 nm and thin shells of about 30 nm composed of numerous small nanocrystals. Prompted by the porous structure and small crystal size of the shell wall, we constructed WO(3) hollow-sphere gas sensors and found that these sensors had good sensitivity to alcohol, acetone, CS(2), and other organic gases.     

Dye-sensitized solar cells based on WO3

In research on alternative photoanode materials for dye-sensitized solar cells (DSCs), there is rarely any report on WO(3), probably due to its acidic surface and more positive (vs NHE) conduction band edge position compared to TiO(2) and ZnO. For the first time, dye-sensitized solar cells based on porous WO(3) nanoparticle films were successfully fabricated with efficiency of up to 0.75%. The multicrystalline structure of WO(3) was examined by Raman spectroscopy and X-ray diffraction analysis. It was found that significant performance enhancement can be obtained from treating the WO(3) nanoparticle film with TiCl(4); the TiCl(4)-treated WO(3) DSCs were recorded with efficiency reaching 1.46%.     

Electrochemical lithium intercalation into WO3 and lithium tungstates Li x WO3+ x /2 of various structures

Hexagonal and monoclinic tungsten trioxides WO₃ and hexagonal lithium tungstates Li _x WO_{3+ x /2} (x = 0.10–0.42) from a soft chemistry route were used as the active cathode material in secondary lithium batteries. The hexagonal structures, regardless of their being an oxide or a tungstate, showed higher specific capacities and better cycling behavior in Li⁺ intercalation reactions than the monoclinic form. The presence of pre-allocated lithium (as Li₂O) in hexagonal tungstates decreased the capacity for lithium intercalation. Additionally, the plot of open-circuit voltage (OCV) against the depth of intercalation (n) for anhydrous tungstates showed two straight lines with different slopes that can be related to the structural changes in lithium intercalation. The effective diffusion coefficients of lithium insertion into the host structure, D˜, were also found to be dependent on the structure and the composition of these compounds. Received: 28 November 1997 / Accepted: 6 March 1998     

Combustion synthesis and characterization of nanocrystalline WO3

The energy payback time associated with the semiconductor active material is an important parameter in a photovoltaic solar cell device. Thus lowering the energy requirements for the semiconductor synthesis step or making it more energy-efficient is critical toward making the overall device economics more competitive relative to other nonpolluting energy options. In this communication, combustion synthesis is demonstrated to be a versatile and energy-efficient method for preparing inorganic oxide semiconductors such as tungsten trioxide (WO3) for photovoltaic or photocatalytic solar energy conversion. The energy efficiency of combustion synthesis accrues from the fact that high process temperatures are self-sustained by the exothermicity of the combustion process, and the only external thermal energy input needed is for dehydration of the fuel/oxidizer precursor mixture and bringing it to ignition. Importantly, we show that, in this approach, it is also possible to tune the optical characteristics of the oxide semiconductor (i.e., shift its response toward the visible range of the electromagnetic spectrum) in situ by doping the host semiconductor during the formative stage itself. As a bonus, the resultant material shows enhanced surface properties such as markedly improved organic dye uptake relative to benchmark samples obtained from commercial sources. Finally, this synthesis approach requires only very simple equipment, a feature that it shares with other "mild" inorganic semiconductor synthesis routes such as sol-gel chemistry, chemical bath deposition, and electrodeposition. The present study constitutes the first use of combustion synthesis for preparing WO3 powder comprising nanosized particles.     

Nanostructure-based WO3 photoanodes for photoelectrochemical water splitting

Nanostructured WO(3) has been developed as a promising water-splitting material due to its ability of capturing parts of the visible light and high stability in aqueous solutions under acidic conditions. In this review, the fabrication, photocatalytic performance and operating principles of photoelectrochemical cells (PECs) for water splitting based on WO(3) photoanodes, with an emphasis on the last decade, are discussed. The morphology, dimension, crystallinity, grain boundaries, defect and separation, transport of photogenerated charges will also be mentioned as the impact factors on photocatalytic performance.     

一种新的WO3纳米管的制备方法

一维纳米材料因可用来构造高性能纳米器件的结构单元而成为纳米材料研究的热点．目前的研究重点集中在材料的制备和结构性能表征方面,已发展了多种制备方法,主要有模板法、V-L-S法、L-L-S法和V-S法等,其中阳极氧化铝(AAO)模板法是制备一维材料的好方法．AAO模板的制备工艺已相当成熟,     

Enhanced electrochromic properties of self-organized nanoporous WO3

Self-organized nanoporous layers of WO₃ were grown by anodization, and their electrochemical and electrochromic properties were investigated and compared to compact anodic layers. As-formed WO₃ layers had an amorphous structure but could be transferred to a monoclinic structure by thermal annealing treatment. Compared to the compact layer, the nanoporous WO₃ layer showed strongly enhanced ion intercalation capacity with reversible characteristics during electrochemical cycling processes. The nanoporous structures showed a significantly enhanced electrochromic contrast, faster switching response, and less sensitivity to intercalation loss by crystallization.     

壳聚糖辅助制备WO_3薄膜材料及其电致变色性能

以壳聚糖(CS)为辅助材料,利用层层自组装方法(LbL)制备了WO3复合薄膜材料(CS/WO3).采用紫外-可见吸收光谱(UV-Vis)、扫描电子显微镜(SEM)和循环伏安扫描(CV)等手段对CS/WO3纳米复合材料的形貌和电化学性能进行了表征.利用电化学和UV-Vis联机技术研究了复合材料的电致变色性能.结果表明,该复合材料呈现出从无色到蓝色的颜色调变,其光反差可达48.0%,着色效率为58.5cm2/C,着色与褪色时间分别为9.5和1.8s.     

Dynamic disorder in ammonium oxofluorotungstates (NH4)2WO2F4 and (NH4)3WO3F3

Ammonium oxofluorotungstates, (NH₄)₂WO₂F₄ and (NH₄)₃WO₃F₃, are characterized by vibration spectroscopy and quantum chemistry methods with the use of NMR ¹⁹F and ¹H data. It is shown in the approximation of the density-functional theory that in isolated octahedrons [WO₂F₄]^2? and [WO₃F₃]^3? the mutual arrangement of oxygen atoms in cis-position corresponds to the energy minimum. The presence of intraspheric disorder in [WO₃F₃]^3? (unlike [WO₂F₄]^2?) explains the complex character of vibrational spectra of this anion and eliminates existent in the literature differences in their interpretation (between C _2v and C _3v structure variants). Models of intraspheric dynamics of [WO₃F₃]^3? are discussed.     

Deactivation of the TiO2 photocatalyst by coupling with WO3 and the electrochemically assisted high photocatalytic activity of WO3

Patterned TiO2 stripes were formed on a sol-gel crystalline WO3 film by using a chemically modified sol-gel method (pat-TiO2/WO3), and the coupling effect on the photocatalytic activity was studied. Although the photoinduced electron transfer from TiO2 to WO3 was confirmed by labeling and visualization of the reduction sites with Ag particles, the photocatalytic activities of TiO2 for both the gas-phase oxidation of CH3CHO and the liquid-phase oxidation of 2-naphthol decreased significantly with the coupling. This finding was rationalized in terms of the decrease in the rate of the electron transfer from the semiconductor-(s) to 02 with the coupling, which was estimated from the kinetic analysis of the photopotential relaxation. When the excited electrons were removed by a SnO2 underlayer, the WO3 film exhibited a high photocatalytic activity exceeding that of TiO2 for the oxidation of 2-naphthol.     

Conductivity of composite materials based on Me2(WO4)3 and WO3 (Me = Sc,In)

Composites {Me₂(WO₄)₃ ? xWO₃} (Me = Sc, In) (x = 0.5–99%) are synthesized and characterized by XRD and electron microscopy methods and also by the density and specific surface measurements. Temperature dependences of the total conductivity of composites are measured. The contributions of σ_tot and σ_el are assessed by the $\sigma (a_{O_2 } )$ and EMF methods. The concentration dependences of conductivity and activation energy are plotted based on the σ_tot and σ_ion data. It is shown that (a) in the interval x = 0–30 vol % WO₃ (0–70 mol %), the conductivity is independent of composition and the ionic component prevails; (b) in the interval x = 60–94.5 vol % (90–99 mol %), the electron conductivity prevails and increases with the increase in x; (c) in the x interval of 30–60 vol % WO₃ (70–90 mol %), the conductivity is mixed, i.e., electron(n-type)-ionic; the latter region represents the transition interval from ionic to electron conductivity as x increases. These data are compared with the results obtained earlier for MeWO₄-WO₃ composites (Me = Ca, Sr, Ba). As regards the structural topology, the {Me₂(WO₄)₃ ? xWO₃} composites pertain to the randomly distributed type. It is shown that in contrast to {Me^IIWO₄ · xWO₃} composites, the composites under study do not form the nonautonomous interface phase with the high ionic conductivity. The possible reasons for the observed differences in the topology and the conduction type of composites based on MeWO₄ and Me₂(WO₄)₃ are analyzed.     

WO3基气敏材料研究进展

综述了近年来国内外对WO3基气敏材料的研究状况,对制备工艺、防团聚技术、掺杂效应及气敏机理等进行了分析比较,并对今后的研究方向提出了一些看法。     

In situ growth of metal particles on 3D urchin-like WO3 nanostructures

Metal/semiconductor hybrid materials of various sizes and morphologies have many applications in areas such as catalysis and sensing. Various organic agents are necessary to stabilize metal nanoparticles during synthesis, which leads to a layer of organic compounds present at the interfaces between the metal particles and the semiconductor supports. Generally, high-temperature oxidative treatment is used to remove the organics, which can extensively change the size and morphology of the particles, in turn altering their activity. Here we report a facile method for direct growth of noble-metal particles on WO(3) through an in situ redox reaction between weakly reductive WO(2.72) and oxidative metal salts in aqueous solution. This synthetic strategy has the advantages that it takes place in one step and requires no foreign reducing agents, stabilizing agents, or pretreatment of the precursors, making it a practical method for the controlled synthesis of metal/semiconductor hybrid nanomaterials. This synthetic method may open up a new way to develop metal-nanoparticle-loaded semiconductor composites.     

Characterization of Electrochromic WO3-Layers Prepared by Sol-Gel Nanotechnology

Stable tungsten oxide coating sols suitable for electrochromic applications were prepared by a modified peroxotungstic acid route. Layers up to 250 nm thickness could be deposited on ITO-coated and/or FTO-coated glass substrates in a single dip-coating process. Optoelectrochemical measurements were employed to determine the variation of the electrochromic properties (change in optical density (OD) and switching times) of WO3-layers, investigated as a function of coating parameters, such as chamber humidity and the temperature of heat treatment. High resolution transmission electron microscopy (HR-TEM) has shown that the optimized layers possess a partially crystalline morphology with nanocrystalline regions 2–3 nm in size.     

高度有序氧化钨纳米棒的制备和表征

采用直流磁控溅射法结合阳极氧化法在铝基纳米点阵上制备氧化钨(WO3)纳米棒. 运用原子力学显微镜(AFM), 电子扫描显微镜(SEM), X射线衍射仪(XRD), 电化学工作站(EW)和紫外-可见分光光度计(UV)观察表征了WO3纳米棒的表面形貌、结构、光学性能和电致变色性能. 结果表明: 在溅射过程中, 溅射粒子优先沉积于铝基纳米点阵的凸点上, 然后成核并形成棒状; WO3纳米棒的直径约为200 nm, 与铝基纳米点阵的直径一致, 拥有一定的电致变色性能.     

Morphology control and photocatalytic characterization of WO3 nanofiber bundles

WO₃ nanofiber bundles with high photocatalytic activity have been synthesized through the soluble salt-assisted hydrothermal method.