Mg掺杂ZnO纳米晶的低温共沉淀法制备及光学性质

采用共沉淀(co-precipitation)法制备了Mg掺杂ZnO纳米晶,分别用X射线衍射(XRD)、傅立叶变换红外光谱(FTIR)、紫外可见吸收(UV-Vis)光谱、光致发光(PL)光谱、透射电镜(TEM)、电子顺磁共振(EPR)等分析手段对样品进行了表征。探究了Mg离子在ZnO纳米晶中的存在状态,ZnO纳米晶颗粒尺寸和发射光谱随Mg掺杂浓度的变化,并对其发光机理进行了分析。结果表明:Mg离子在ZnO晶格中以部分晶格位,部分间隙位的方式存在,没有形成MgO表面壳层结构;随Mg掺杂浓度的增大,ZnO纳米晶的颗粒尺寸变小,发射光的光强增大。发射光的最佳激发波长为342nm,中心波长为500nm,荧光量子产率为22.8%。实验分析表明:Mg离子的掺杂在ZnO纳米晶中引入了锌空位(VZn),间隙位的镁离子(IMg),提供了新的复合中心,从而增强了ZnO纳米晶的光致发光。     

电化学方法制备ZnO纳米颗粒掺杂类金刚石薄膜及其场发射性能研究

采用液相电化学沉积技术制备了ZnO纳米颗粒掺杂的类金刚石(DLC)薄膜, 研究了ZnO纳米颗粒掺杂对DLC薄膜场发射性能的影响. 利用X射线光电子能谱、透射电子显微镜、Raman光谱以及原子力显微镜分别对薄膜的化学组成、 微观结构和表面形貌进行了表征. 结果表明: 薄膜中的ZnO纳米颗粒具有纤锌矿结构, 其含量随着电解液中Zn源的增加而增加. ZnO纳米颗粒掺杂增强了DLC薄膜的石墨化和表面粗糙度. 场发射测试表明, ZnO纳米颗粒掺杂能提高DLC薄膜的场发射性能, 其中Zn与Zn+C的原子比为10.3%的样品在外加电场强度为20.7 V/μm时电流密度达到了1 mA/cm². 薄膜场发射性能的提高归因于ZnO掺杂引起的表面粗糙度和DLC薄膜石墨化程度的增加.     

铕掺杂氧化锌纳米棒阵列材料的制备及光学性能研究

通过低温化学方法在多孔硅柱状阵列(NSPA)衬底上制备得到铕掺杂ZnO(ZnO∶Eu)纳米棒阵列结构。实验方法简单、条件温和,有效地实现了ZnO纳米棒和铕离子之间的能量转移,丰富了ZnO纳米半导体材料体系的发光。X射线衍射以及X射线光电子能谱证实铕离子成功掺杂进了ZnO晶体中。室温荧光光谱测试结果表明:ZnO∶Eu纳米棒阵列可实现从紫外光到蓝-绿光的宽谱带发射,其中发光中心位于～380 nm的紫外光源于ZnO的带边发射,位于450～570 nm的蓝-绿光源于ZnO的本征缺陷发光,而位于～615 nm的红光发光则源于铕离子核外电子4f壳层结构。同时借助于能带示意图对光致发光机理进行了分析。     

Ag掺杂氧化锌纳米材料的制备及高压相变拉曼光谱研究

宽禁带直接带隙半导体材料氧化锌（ZnO）,具有优异的光电性能、机械性能和化学特性。ZnO材料的结构对其性能影响较大,元素掺杂可改变ZnO晶体结构和带隙宽度,是提升ZnO材料性能的有效手段,当前常用Ag掺杂ZnO即为提高光催化反应效率。高压独立于温度、成分,是调控材料结构组织性能的重要手段,是产生新材料、发现新调控原理的重要因素。该研究通过对比纯ZnO晶体和Ag掺杂ZnO晶体的高压相变行为,揭示了元素掺杂对ZnO纳米晶体材料结构性能的影响。研究首先采用水热法辅助制备纯ZnO纳米微球和Ag掺杂ZnO纳米微球（1∶150Ag/ZnO）,表征结果显示水热法合成的纯ZnO和1∶150Ag/ZnO均为六角纤锌矿晶体结构,形貌均为几十纳米尺寸小颗粒堆积形成的微球,ZnO晶格常数随着Ag离子掺杂而变大,Ag掺杂导致ZnO晶格膨胀。随后应用金刚石压腔结合原位拉曼光谱技术测定了纯ZnO和Ag掺杂ZnO的高压结构相变行为。相比于纯ZnO拉曼峰,Ag掺杂ZnO的E₂（high）振动模式439 cm-1拉曼峰峰宽变窄,并呈现向低频方向移动的趋势,与无定形ZnO谱峰相近,表明Ag+取代Zn2+影响了Zn-O键,同时也影响了ZnO晶格结构的长程有序性。随体系压力增大,表征六角纤锌矿结构ZnO的拉曼特征峰439 cm-1出现瞬间弱化和宽化。压力增大至9.0 GPa时,纤锌矿结构ZnO拉曼特征峰439 cm-1消失,585 cm-1处出现新峰,ZnO晶体发生由六角纤锌矿向岩盐矿的结构转变。压力继续增大至11.5 GPa,新的拉曼峰显著增强,峰形变窄,同时向高波数方向移动,相变完成,岩盐矿结构ZnO性能稳定。1∶150 Ag/ZnO从六角纤锌矿结构到立方岩盐结构的相变压力为7.2 GPa,低于纯ZnO。相变压力降低表明晶体结构稳定性下降,可能的原因在于掺杂Ag导致ZnO晶格膨胀,晶体结构松弛,两相相对体积变化增加,从而导致相变势垒降低,使样品在较低压力下发生相变。纳米材料的高压研究揭示了元素掺杂对材料结构稳定性的影响,是纳米材料调控原理的潜在研究手段。     

水热合成ZnO:Cd纳米棒的微结构及光致发光特性

采用水热法制备了ZnO和不同掺杂浓度的ZnO:Cd纳米棒,通过SEM,XRD、拉曼光谱等的分析,研究了ZnO和ZnO:Cd的微结构并测试分析了其光致发光特性.结果表明,ZnO和ZnO:Cd纳米棒呈六角纤锌矿结构,Cd掺杂使得纳米棒体积更小.由于内部张应力的影响,Cd掺杂使得材料光学带隙减少.当掺杂浓度为2%时,合成的材料光致发光谱中出现了位于2.67 eV处,由导带底和Zn空位(VZn)缺陷能级跃迁造成的蓝光发射峰,并且Cd的掺入使得位于2.90 eV附近的紫光发射峰强度增强,对于研究ZnO蓝紫发光器件具有重要的意义.     

掺银氧化锌纳米棒的水热法制备研究

利用水热法在直流磁控溅射制备的掺铝氧化锌 (AZO) 种子层上制备了不同形貌和光学性能的掺银ZnO纳米棒, 并采用XRD、扫描电镜、透射谱、光发射谱和EDS谱详细研究了Ag离子与Zn离子的摩尔百分比 (R_Ag/Zn) 及AZO种子层对掺银ZnO纳米棒的结构和光学性质的影响. 随着R_Ag/Zn的增加, 掺银ZnO 纳米棒的微结构和光学性质的变化与银掺杂诱导的纳米棒的端面尺寸变化有关. 平均端面尺寸的变化归结于种子层颗粒大小和颗粒数密度不同导致掺入的Ag离子的相对比例不同. 溅射15 min的AZO种子层上生长的ZnO纳米棒由于缺陷增多导致在可见光区的发光峰明显强于溅射10 min 的AZO种子层上、相同R_Ag/Zn 条件下生长的ZnO纳米棒. Ag掺杂产生的点缺陷增多导致可见光区PL波包较宽. 纯ZnO纳米棒的微结构与种子层厚度导致的结晶度和颗粒大小有关. 关键词： ZnO纳米棒 水热法 Ag掺杂 直流磁控溅射     

Cu掺杂ZnO纳米材料的制备及表征

利用CuO作为前驱体对ZnO进行了Cu掺杂研究,分别在不同温度下获得了ZnO纳米带及有纳米带构成的微米花状结构,对其生长机理进行了分析。并且以Cu片为衬底获得了ZnO的纳米梳以及有纳米梳构成的多层结构ZnO。XRD表明产物中只有ZnO单质相的存在,EDS证明产物中存在Cu元素。ZnO室温下的PL谱表明其UV与深能级发射强度比随Cu掺杂量的增加而变大,说明Cu的掺杂能够降低ZnO的缺陷峰强度。     

La、Ce掺杂ZnO纳米晶的发光特性

共沉淀法制备了稀土镧、铈掺杂的ZnO半导体纳米晶。X射线衍射(XRD)结果表明:掺杂的ZnO纳米晶为六方纤锌矿结构,随掺杂浓度增加ZnO粒径减小。对铈掺杂纳米ZnO,以波长380nm激发,在443nm处出现了半峰宽较窄的强的蓝光发射峰;镧掺杂ZnO纳米晶则为从418~610nm的多峰宽带发射。     

Sn掺杂ZnO纳米晶的水热法制备及光学性能

以ZnCl2和NaOH为原料,用SnCl4·4H2O作掺杂剂,通过水热法合成了Sn掺杂ZnO纳米颗粒。利用X射线衍射(XRD)、场发射扫描电镜(FE-SEM)、紫外-可见吸收光谱(UV-Vis)及光致发光(PL)光谱等测试技术对样品的物相、形貌及光学性能进行了表征。结果表明:制得的Sn掺杂ZnO纳米粒子具有六角纤锌矿结构。随着锡掺杂浓度的增大,纳米晶的平均粒度增加,晶体形貌由短棒状向单锥和双锥状转变;提高前驱液的pH值,所得样品的形貌由长柱状向短柱状转变。室温下,观测到三个光致发光带,一个峰值在433nm处的强紫光发射峰,一个约在401nm处的近紫外发光峰及一个在466nm处的弱蓝光发光峰。在实验掺杂浓度范围内,Sn的掺杂只是改变纳米ZnO的发光强度,对发光峰位置影响不大。     

掺杂铁的CeO2纳米颗粒的制备与表征

利用反相共沉淀法,合成了掺杂过渡金属铁的CeO2纳米颗粒.通过X射线衍射(XRD)、透射电镜(TEM)、傅里叶变换红外(FTIR)光谱、紫外-可见(UV-Vis)光谱等测试手段对产物进行了分析和表征.结果表明,掺杂铁的CeO2纳米颗粒是纯立方莹石结构;过渡金属铁掺入了CeO2的晶格;其相比于不掺铁的CeO2纳米颗粒吸收...     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Hybrid Wavelength and Code Division Multiple Access in Optical Networks

A review of schemes for multiple access in fiber optic networks shows that a hybrid of wavelength and code division multiple access (WCDMA) combines the best features of both. In particular, the hybrid scheme retains the large information carrying capacity of wavelength division multiple access (WDMA) and flexibility of code division multiple access (CDMA). In this paper WDMA, optical CDMA (OCDMA), and WCDMA networks are discussed. In OCDMA networks, concept of incoherent and coherent coding including inverse decoding and matched filter is introduced. The delay performance of both WDMA and WCDMA networks, under the simple suboptimum access protocols based on cyclic search, is computed. It has been shown quantitatively that tuning delay significantly affects the delay performance of both WDMA and WCDMA networks. Futhermore, delay performance of WCDMA networks is always better than the WDMA networks for the same tuning delay, load, and number of users.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.