热历史对尼龙1212熔融行为的影响

利用DSC方法研究了不同热历史条件对尼龙1212熔融行为的影响.不同的热历史条件下,在DSC曲线上,观察到尼龙1212产生2个或3个熔融峰,依据聚合物结晶理论,对各峰的来源进行了分析.在160℃下不同温度退火120 min的尼龙1212样品DSC曲线上,低温结晶熔融峰主要由低温结晶形成的一些微晶体或者片晶熔融产生,其晶体完善程度较差,熔融峰值较低,峰面积较小;主熔融峰是由样品在淬火过程中形成的晶体和升温过程中低温结晶形成的晶体的熔融重结晶形成较为完善的晶体熔融所产生,熔融峰值较高,峰面积较大.在不同的升温速率条件下,熔融峰温度有所移动,表明不同升温速率条件下产生的熔融峰的结晶晶型是相同的.在不同结晶时间下结晶,延长结晶时间对较高完善程度晶体的生长有利.在不同温度下依次退火处理的样品,熔融产生两个附加峰,这两个附加峰的峰温都比它们相应的退火温度高,而峰高和峰面积随退火温度降低而减小.根据等温结晶结果,由Hoffman方法确定了尼龙1212的平衡熔融温度为202.8℃.     

尼龙1010结晶与熔融行为的研究

用DSC研究了降温速率R对尼龙10 10结晶与熔融的影响,以及室温(RT)和液氮(LN)骤冷退火样品的熔融.降温时结晶温度随R增大线性降低;T_g以上可完成结晶时结晶度相同;结晶起始温度>181℃生成的晶体有三个熔融峰,对应于环状和放射状球晶的转化与熔融;在181℃和T_g间结晶,无放射球晶转化峰;T_g下有结晶放热峰样品加热时有冷结晶发生.RT未退火样品三个熔融峰,退火温度T_α≥180℃样品两个峰,结晶度C∝T_a;LN未退火样品单一熔融峰,T_a>160℃双峰,T_a≤160℃三峰,低温峰温与C均∝T.     

结晶／结晶共混体系PPS／PEEK中PPS组分的结晶熔融行为（Ⅱ）──熔融条件对退火样品的影响

结晶／结晶共混体系ＰＰＳ／ＰＥＥＫ中ＰＰＳ组分的结晶熔融行为（Ⅱ）──熔融条件对退火样品的影响麦堪成，许家瑞，梅震，曾汉民（广州中山大学材料科学研究所，广州，５１０２７５）关键词聚苯硫醚，聚醚醚酮，结晶熔融行为，熔融双峰聚苯硫醚（ＰＰＳ）的结晶熔融行...     

含间位取代苯基聚醚酮酮的结晶与晶体结构研究

通过差示扫描法（ＤＳＣ）及广角Ｘ 射线衍射（ＷＡＸＤ）技术研究了含间位取代苯基聚醚酮酮（ＰＥＫｍＫ）的结晶行为与晶体结构．Ｘ 射线结果表明，从熔融态及玻璃态结晶时，ＰＥＫｍＫ只有一种晶型，其晶胞参数为：ａ＝０７６７２ｎｍ，ｂ＝０６１４９ｎｍ，ｃ＝１５９９ｎｍ．ＤＳＣ结果表明，ＰＥＫｍＫ热分析曲线都出现了熔融双峰，低熔融峰（ＤＯＷｎ）热焓占总热焓４～７％，它源于初始结晶形成的同一晶型不同厚度片晶．低熔融峰在２５０℃以上结晶转化成高熔融峰（Ｉ），ＰＥＫｍＫ平衡熔点为２９５℃     

聚乳酸/矿物填料复合材料的示差扫描量热研究

通过熔融共混法制备了一系列聚乳酸(PLA)/矿物填料复合材料.采用示差扫描量热(DSC)研究了含有碳酸钙(CaCO3)、蒙脱土(MMT)和凹凸棒土(AT)的聚乳酸复合材料在不同热历程中的结晶和熔融行为.研究发现,MMT和AT对PLA的慢速降温结晶无明显影响,而碳酸钙在慢速降温过程中能够有效促进PLA结晶;在2.5 K/min的降温速率下,结晶热焓随碳酸钙含量增加而增加;填料种类和含量会对复合材料升温过程的冷结晶和熔融产生较大影响,低含量矿物填料主要对PLA的冷结晶起成核作用,其中MMT成核效果最好.较高含量下不同填料会对PLA晶体形态产生影响,从而得到多样的DSC曲线变化.     

聚醚醚酮酮的结晶熔融行为

用差示扫描量热法（ＤＳＣ）研究不同热历史聚醚醚酮酮（ＰＥＥＫＫ）的结晶熔融行为。在２２５－３００℃等温热处理样品的ＤＳＣ曲线出现了熔融双峰。低温熔融峰峰温（Ｔｍｌ）较低，Ｔｍｌ与热处理温度Ｔｃ有关；高温熔融峰峰温（Ｔｍ２）较高，Ｔｍ２几乎不受Ｔｃ的影响。研究结果认为，在升温过程中存在结晶的熔融－重结晶过程，熔融双峰归因于结构相同而完整程度不同的ＰＥＥＫＫ结晶的熔融行为。还探讨了升温速度对结晶熔融行     

退火温度和时间对PET高卷速拉伸变形丝熔化与结晶行为的影响

本文用DSC和密度法研究了高卷速拉伸变形丝(DTY)的熔化与结晶行为。定量地测定了不同温度迟火5分钟急冷后的试样,在DSC曲线上出现的各转变峰温和热焓随退火温度变化的规律,找到了DSC测定的熔化热焓和密度法测定的结晶度之间的对应关系。从试样在熔化峰温退火→冷却结晶→再扫描和在熔化峰温→继续扫描两种方式在DSC曲线上所表现的熔化与结晶行为,探讨了试样在熔融状态退火冷却结晶后再扫描出现双熔化峰的原因,继而研究了试样在熔化峰温的退火时间对结晶完善程制的影响。     

热历史对聚醚醚酮及其碳纤维复合材料——Ⅱ.熔融行为的影响

 本文利用差示扫描量热仪(DSC)研究了聚醚醚酮(PEEK)和以PEEK为基体的碳纤维复合材料(APC-2)的热历史对它们熔融行为的影响。在200—315℃结晶并退火热处理后,试样的DSC曲线上出现了两个吸热峰。低温吸热峰(峰温T′_m)较小,并与结晶和退火温度(T_c与在不同T_c下生成的不完整晶体的熔融和重结晶过程有关,而T_m的出现则与完整晶体的熔融过程有关。实验结果表明,T′_m与T_c之间呈线性关系。按文献报道的方法,将T′_m与T_c的直线外推至与T′_m=T_c直线相交,其交点温度即为平衡熔点.结果表明,PEEK和APC-2试样的“平衡熔点”受不同热历史条件下生成晶体的完整程度的影响。当结晶并退火时间越长,求出的“平衡熔点”值越低,并与理论值接近。实验结果还表明,碳纤维表面具有促进PEEK树脂基体晶体完整化的作用,因而导致APC-2试样中PEEK树脂基体的熔点高于纯PEEK树脂。     

芳香聚醚酮酮晶体结构及其晶型变化的研究（Ⅰ）

利用Ｘ射线及热分析技术研究了聚醚酮酮（ＰＥＫＫ）的溶剂诱导结晶及从玻璃态结晶和从熔融态结晶的行为。发现ＰＥＫＫ有两种晶型结构（Ⅰ和Ⅱ），晶型Ⅱ的形成与热历史和溶剂诱导有关，其熔点始终低于Ⅰ型１０℃左右。ＰＥＫＫ的低温熔融峰与其分子链极化有关，而与热历史无关，此低温熔融峰热焓占总热焓２％～１０％，其平衡熔点为４０９℃。     

聚L-乳酸/4,4'-二羟基二苯硫醚共混物的分子间相互作用及结晶和熔融行为

利用红外吸收光谱(FTIR)研究了聚乳酸(PLLA)/4,4'-二羟基二苯硫醚(TDP)熔融共混物的分子间相互作用,结果表明,PLLA的羰基与TDP的羟基之间形成了分子间氢键.通过差示扫描量热(DSC)研究了共混物的玻璃化转变行为及非等温结晶和熔融行为.结果表明,样品的玻璃化转变温度(Tg)随TDP含量的增加呈线性下降.共混物的熔融结晶温度(Tc)、结晶焓(ΔHc)、熔融温度(Tm)及熔融焓(ΔHm)均随TDP含量的增加呈下降趋势,而冷结晶温度的变化趋势则相反.当TDP达到40%(质量分数)时,共混物的DSC曲线既未出现结晶峰,也未出现熔融峰,表明该样品已完全成为非晶态物质.广角X射线衍射(WAXD)分析结果表明,TDP的加入未改变PLLA的晶型,但导致其晶面间距变大,晶体结构变得松散.因此共混物熔点的下降归因于分子间氢键的形成降低了PLLA分子链的运动能力及晶体的紧密程度而非晶型的改变.     

聚芳醚酮类高聚物的合成与热性能研究

利用合成的新型单体,采用亲核取代法制备了5类聚芳醚酮.用DSC和WAXD对聚合物的研究表明:新型聚芳醚酮与聚醚醚酮的结晶结构相同,其熔点及玻璃化转变温度均随聚合物结构单元中酮基含量的增加而升高.     

Melting properties of molten salts and ionic liquids. Chemical homology,correlation, and prediction

The application of the concept of chemical homology to describe melting properties of molten salts and ionic liquids (ILs) is analyzed. This concept was used several years ago to correlate and predict properties of solids and more recently to correlate melting temperatures of ILs. To analyze the characteristics of the extended method, this is first applied to melting properties of organic substances for which abundant data are available. The method is extended to analyze its applicability for properties of molten salts and ILs such as glass transition temperature, heat of melting, and entropy of melting. The foundation of the chemical homology concept is revised, and the difficulties for extending the method to correlate and predict melting properties of ILs are presented. Despite the difficulties, the homology concept can still be used with some conditions and limitations that are analyzed in this article. Several correlations are proposed.     

Melting transitions in metallic elements correlated with shear modulus and atomic volume

We show that two quite recent treatments of dislocation-mediated melting transitions result in the thermal energy associated with the melting temperature, T _m, being expressed as a product of a volume factor and a combination of elastic constants times a lattice structure-dependent factor. We further show that the result for the latent heat of fusion L _m obtained in one of these studies leads to the ratio L _m/GΩ, where G is the shear modulus at melting and Ω the atomic volume, being a constant. Since the ratio of the vacancy formation energy to GΩ is also found to be roughly constant, we suggest that the factor GΩ at melting is crucial in determining the melting temperature, the latent heat of fusion and the vacancy formation energy and we comment on the reasons why this should be so.     

The role of disclinations in two phase changes induced by temperature and pressure in crystalline solids: melting and the brittle–ductile transition

It has long been known that the melting temperature T _m of close-packed metals correlates well with the mono-vacancy formation energy. However, with the possible exception of the face-centered-cubic metals, there is a prior phase transition from a mechanically brittle solid phase to a ductile phase. Here the likely role of disclinations in the brittle-ductile phase change is stressed. The present picture may help to understand the brittle–ductile transition not only in crystalline materials but also in amorphous phases. The structure of such phases can probably be characterized in terms of a disordered disclination network. As examples of elemental crystalline solids, Si and graphite are finally discussed, with the melting under pressure of graphite being quantified.     

Crystallite orientation during melting of oriented ultra-high-molecular-weight polyethylene

The changes in crystallite orientation during melting of oriented ultra-high-molecular-weight polyethylene (UHMW PE) were investigated by means of wide-angle X-ray scattering. The orientation distribution of crystallites in drawn UHMW PE is composed of two components differing in width. The narrow and broad components revealed in this study indicate the existence of two classes of crystallites with different orientability. Some of the crystallites are oriented almost perfectly even at low-draw ratios, while the others do not orient so effectively. The analysis of melting behaviour of such a texture composed of orthorhombic crystals indicates that highly oriented crystallites are formed by taut molecules and transform first to the hexagonal phase, while the molecules constituting low-oriented crystallites melt directly to the typical amorphous phase. The increase in orientation of highly oriented crystallites during their partial melting, observed in the samples kept at constant length and even those allowed to shrink under constant load, can be explained by the kinetic factor proposed by Ziabicki. Received: 11 September 1998 Accepted in revised form: 18 February 1999     

Thermal transitions of DODAB vesicular dispersions

Two endothermic transitions, at 36°C and 44°C, were observed with differential scanning calorimetry (DSC) upon heating dioctadecyldimethylammonium bromide vesicle dispersions that were equilibrated below 15°C while in samples kept at 25°C there was only the transition at 44°C, which was shown to be the gel to liquid–crystalline transition by ¹H-NMR measurements. The transition at 36°C was reversed in an exothermic transition around 13°C upon cooling. The slowness of this transition at ambient temperatures suggests that the presence of the transition at 36°C in a DSC upscan depends strongly on the sample history.     

小尺寸金属团簇熔化过程的分子动力学模拟

运用分子动力学方法模拟了小尺寸金属团簇的熔化过程, 原子之间的作用采用嵌入原子法(EAM)模型, 计算了均方根键长涨落δ随温度的变化, 以及升温过程中团簇热容的变化. 包含55、56个原子的面心立方(FCC)结构Au团簇的熔化过程是基本相同的. 而同样结构和数目Cu团簇的熔化过程却呈现出不同的趋势. Cu55、Cu56在模拟过程中都出现了FCC结构到二十面体结构的转变. 但由于表面多出了一个原子, Cu56的热容曲线比Cu55多了一个峰, 体系出现了预熔化现象. 这表明小尺寸团簇的固液转变的过程与团簇的原子类型、几何结构和原子数目密切相关.     

X射线荧光光谱法测定黑龙江省有机碳含量较高样品中的硅、铝、铁等元素

通过事先对有机碳含量较高的样品进行高温灼烧,计算其烧失量,再将灼烧后的样品经专用熔剂熔融制样后,经X射线荧光光谱仪测定,能够有效地去除因有机质含量高导致的分析结果的偏差,而且较湿法化学分析节省时间。实验结果表明,该方法的分析结果与湿法化学分析结果偏差很小,准确度较直接压片分析有了大幅提高。     

PBT／PET共混体系的熔融行为

用差示扫描量热法（ＤＳＣ）考察了ＰＢＴ／ＰＥＴ共混体系的结晶熔融行为，在共混体系中两组份的结晶熔上均随着含量的减小而下降，熔点下降既有形结构变化因素，又有因两组份相容而引起的热力学因素。熔融热焓△Ｈｍ的变化与两组份结晶熔点的变化有相似的规律。这些结果说明在共混体系中ＰＥＴ、ＰＢＴ两组份在结晶一熔融过程中存在相互协同作用，同时也说明ＰＢＴ、ＰＥＴ两组份是晶相分离的，而非晶区是相混容的。     

Molecular Dynamics Investigation of Differences in Melting Behaviors of Cu57 and Cu58 Clusters

Within the framework of the embedded-atom method, we performed molecular-dynamics calculations to investigate the structural transformation during melting of two copper clus- ters containing 57 and 58 atoms. The simulation results reveal how their different structural changes can strongly influence internal energy and radial distribution functions. The local structural patterns of different regions during the temperature increase, determined by atom density profiles, are identified for the melting of each cluster. The simulations show sensi- tivities of the structural changes for these two small size clusters with different structures.