Temperature dependence of spontaneous magnetization of spinel ferrites with a frustrated magnetic structure

The spontaneous magnetization of the Ni_0.4Fe_0.6[Ni_0.6Cr_1.4]O₄, Cu_0.4Fe_0.6[Ni_0.6Cr_1.4]O₄, and Zn_0.4Fe_0.6[Ni_0.6Cr_1.4]O₄ samples has been investigated. Based on the results obtained, it is concluded that the anomalous temperature dependences of spontaneous magnetization stem from the presence of a frustrated magnetic structure in at least one of the sublattices.     

Temperature dependence of the spontaneous magnetization of Cu x Ni1-x Fe0.6Cr1.4O4 chromite ferrites with a frustrated magnetic structure

The behavior of the spontaneous magnetization σ _s (T) of samples in the Cu _x Ni_1-x Fe_0.6Cr_1.4O₄ system (x = 0, 0.1, 0.2, 0.3, 0.4) with variations in temperature is studied. The conclusion is drawn that the degree of frustration of magnetic interactions in the A sublattice increases with increasing x, with the result that the dependence σ _s (T) transforms from an N-type curve to an anomalous dependence of a new type.     

Pinned and entropic disordering of mixed spinel ferrite Ga0.8Fe0.2NiCrO4

Mössbauer and magnetic hysteresis measurements (T=1.4 K and H=-12 to+12 kOe) confirm the existence of pinned and entropic spins in the frustrated disordered spinel ferrite (Ga³⁺_0.8Fe³⁺_0.2) [Ni²⁺Cr³⁺]O₄, as suggested by earlier studies.     

Magnetism in some layer molecular magnets as revealed by Mössbauer spectroscopy

⁵⁷Fe Mössbauer spectroscopy was used to explore magnetic properties of two 2D molecular ferrimagnets. In NPn₄[Fe^IIFe^III(ox)₃] (Pn = n-C₅H₁₁, (ox) =(C₂O₄)^2?), the previously reported negative magnetization is shown here by external field studies to be due to a cross-over between Fe^III and Fe^II- magnetizations. The form and parameters of the magnetic Hamiltonian describing the temperature dependence of both the Fe^III hf-field and net magnetizations has been determined. In NBu₄[Mn^IIFe^III(ox)₃] (Bu = n-C₄H₉) soft XY-magnet the low temperature relaxation spectra are interpreted in terms of slowly varying classical magnetization-evolution at low temperature.     

The tunable magnetic properties and microstructures of Co–Ni double-substituted M-type Casrla hexaferrites

M-type hexaferrites with Co²⁺ and Ni²⁺ions substituting for Fe³⁺ ions (Ca_0.30Sr_0.35La_0.35Fe_12.0−x(Co_0.5Ni_0.5)_xO₁₉, 0.0 ≤ x ≤ 1.0) were prepared by the traditional solid state method. X-ray diffractometer (XRD), field emission scanning electron microscopy (FE-SEM), physical property measurement system-vibrating sample magnetometer (PPMS-VSM) have been employed to study the microstructures and magnetic properties of hexaferrites. XRD patterns showed that the single magnetoplumbite phase is obtained if Co–Ni content (x) ≤ 0.4 and impurity phases are observed in the structure when Co–Ni content (x) ≥ 0.4. FE-SEM micrographs showed that the hexaferrites with hexagonal platelet-like grains is obtained. The saturation magnetization (M_s), remanent magnetization (M_r), M_r/M_s ratio, magneton number (n_B), coercivity (H_c), magnetic anisotropy field (H_a) and first anisotropy constant (K₁) decrease with increasing Co–Ni content (x) from 0.0 to 1.0. And our reported results with tunable H_c and M_r can be used for recording applications.     

Preparation and magnetic properties of the conductive Co(1−x)NixFe2O4/polyaniline microsphere composites

Core-shell Co_(1−x)Ni_xFe₂O₄/polyaniline nanoparticles, where the core was Co_(1−x)Ni_xFe₂O₄ and the shell was polyaniline, were prepared by the combination of sol-gel process and in-situ polymerization methods. Nanoparticles were investigated by Fourier transform spectrometer, X-ray diffraction diffractometer, Scanning electron microscope, Differential thermal analysis and Superconductor quantum interference device. The results showed that the saturation magnetization of pure Co_(1−x)Ni_xFe₂O₄ nanoparticles were 57.57 emu/g, but Co_(1−x)Ni_xFe₂O₄/polyaniline composites were 37.36 emu/g. It was attributed to the lower content (15 wt%), smaller size and their uneven distribution of Co_(1−x)Ni_xFe₂O₄ nanoparticles in the final microsphere composites. Both Co_(1−x)Ni_xFe₂O₄ and PANI/Co_(1−x)Ni_xFe₂O₄ showed superparamagnetism.     

Structural,electrical transport,and magnetic properties of Ni1−xZnxFe2O4

Structural, electrical, and magnetic properties of Ni_1−xZn_xFe₂O₄ (x=0.2, 0.4) samples sintered at various temperatures have been investigated thoroughly. The bulk density of the Ni_0.8Zn_0.2Fe₂O₄ samples increases as the sintering temperature (T_s) increases from 1200 to 1300 °C and above 1300 °C the bulk density decreases slightly. The Ni_0.6Zn_0.4Fe₂O₄ samples show similar behavior of changes to that of Ni_0.8Zn_0.2Fe₂O₄ samples, except that the bulk density is found to be the highest at 1350 °C. The DC electrical resistivity, ρ(T)$\rho (T)$, decreases as the temperature increases indicating that the samples have semiconductor-like behavior. As the Zn content increases, the Curie temperature (T_c), resistivity, and the activation energy decrease while the magnetization, initial permeability, and the relative quality factor (Q) increases. A Hopkinson peak is obtained near T_c in the real part of the initial permeability vs. temperature curves. The ferrite with higher permeability has a relatively lower resonance frequency. The initial permeability and magnetization of the samples has been found to correlate with density, average grain sizes. Possible explanation for the observed structural, magnetic, and changes of resistivity behavior with various Zn content are discussed.     

Effect of the spin-orbit interaction of Ni2+ ions with a triplet orbital ground state on the magnetostriction of NiFe0.5Cr1.5O4 ferrite

The magnetization σ and the longitudinal (λ_∥) and transverse (λ_⊥) magnetostrictions of the NiFe_0.5Cr_1.5O₄ ferrite containing the tetrahedral ions Ni²⁺ with the triplet orbital ground state have been investigated for the first time at a temperature of 4.2 K in fields up to 55 kOe. It is revealed that the NiFe_0.5Cr_1.5O₄ ferrite exhibits an anomalously large magnetic anisotropy (H _c=12.5 kOe) and magnetostrictions (λ_∥≈?870×10^?6 and λ_⊥≈800×10^?6). In strong fields, the magnetostrictions λ_∥ and λ_⊥ are found to be anisotropic in character; i.e., the susceptibility Δλ_∥p and Δλ_⊥p. The conclusion is drawn that the studied compound is characterized by two paraprocesses: one paraprocess in the B sublattice has an exchange nature, and the second process in the A sublattice is due to the spin-orbit interaction of Ni _A ²⁺ ions.     

Studies on partially oxidised one-dimensional bis(oxalato)platinate salts containing divalent cations

The preparation and electrical conduction properties of the isostructural one-dimensional conductors Ni_0.84[Pt(C₂O₄)₂]·6H₂O(Ni-OP) and Mn_0.81[Pt(C₂O₄)₂]·6H₂O(Mn-OP) are described. Ni-OP exhibits a similar tem dependence of conductivity to the isostructural compounds Co_0.83[Pt(C₂O₄)₂]·6H₂O(Co-OP) and Zn_0.81[Pt(C₂O₄)₂]·6H₂O whereas the behaviour of Mn-OP is rather like that of K₂[Pt(CN)₄]Br_0.3·3H₂O. These differences are discussed in terms of the variation from compound to compound of the critical temperature for the formation of the “non-Peierls” superstructure (T_c) and the temperature at which the CDW/PD on adjacent conducting chains undergo three-dimensional ordering (T_3D). The variation of thermopower with temperature for Co-OP and Mg_0.82[Pt(C₂O₄)₂]·6H₂O is reported and related to the conduction properties and phase changes which have been observed for these compounds. For the isostructural series M_0.8[Pt(C₂O₄)₂]·6H₂O (M = Mg, Mn, Co, Ni or Zn) the variation of (T_3D) from compound to compound is related to differences in the polarizing power of the cations.     

Vacancy-induced spin-glass behavior of Prussian blue analogue Fe1.1Crx[Cr (CN)6]0.6−x·nH2O nanowires

Prussian blue analogue Fe^II_1.1Cr^II_x[Cr^III(CN)₆]_0.6−x·nH₂O nanowires were synthesized by electrodeposition. The magnetic properties investigation indicates that the nanowires exhibit cluster spin-glass behavior, which undergoes a magnetic transition to a frozen state below about 62 K. Spin disorder arising from reduced coordination and broken exchange bonds between spin centers due to the structural defects may be the reason that causes the spin-glass freezing behavior. The negative magnetization observed at temperature lower than the compensation temperature (T_comp∼43 K) at a field of 10 Oe may be due to the different temperature dependences of the ferromagnetic site Fe-Cr and antiferromagnetic site Cr-Cr.     

Magnetoelectric characterization of xNi0.75Co0.25Fe2O4-(1−x)BiFeO3 nanocomposites

Magnetoelectric (ME) nanocomposites containing Ni_0.75Co_0.25Fe₂O₄-BiFeO₃ phases were prepared by citrate sol-gel process. X-ray diffraction (XRD) analysis showed phase formation of xNi_0.75Co_0.25Fe₂O₄-(1−x)BiFeO₃ (x=0.1, 0.2, 0.3 and 0.4) composites on heating at 700 °C. Transmission electron microscopy revealed the formation of powders of nano order size and the crystal size was found to vary from 30 to 85 nm. Dispersion in dielectric constant (ε) and dielectric loss (tan δ) in the low-frequency range have been observed. It is seen that nanocomposites exhibit strong magnetic properties and a large ME effect. On increasing Ni_0.75Co_0.25Fe₂O₄ contents in the nanocomposites, the saturation magnetization (M_S) and coercivity (H_C) increased after annealing at 700 °C. The large ME output in the nanocomposites exhibits strong dependence on magnetic bias and magnetic field frequency. The large value of ME output can be attributed to small grain size of ferrite phase of nanocomposite being prepared by citrate precursor process.     

Investigating the influence of Cr-Zn substitution on magnetic and structural properties of M-type SrBaSm hexaferrites Sr0.6Ba0.1Sm0.3Fe12.0-x(Cr0.6Zn0.4)xO19

The Cr-Zn substituted M-type SrBaSm hexaferrites Sr_0.6Ba_0.1Sm_0.3Fe_12.0-x(Cr_0.6Zn_0.4)_xO₁₉ (0.00?≤?x?≤?0.75) were synthesized by the conventional ceramic route. The crystal structures were identified by X-ray diffraction. XRD analysis showed that the magnetic powders with CrZn content (x) from 0.00 to 0.30 had M-type as major phase and α-Fe₂O₃ as impurity phase, while the magnetic powders with CrZn content (x)?≥?0.45 exhibited a single M-type phase. The grain morphology of the magnets was observed by a field emission scanning electron microscopy (FE-SEM). The FE-SEM images show that all grains were distributed homogeneously and had regular hexagonal platelet-like shape. The magnetic properties of the magnets were derived from the demagnetizing curves. The remanence (B_r) and maximum energy product [(BH)_max] first increased with increasing CrZn content (x) from 0.00 to 0.30, and then decreased when CrZn content (x)?≥?0.30. The intrinsic coercivity (H_cj) and magnetic induction coercivity (H_cb) first decreased with increasing CrZn content (x) from 0.00 to 0.30, and then slightly fluctuated and basically remained unchanged when CrZn content (x) ≥ 0.30.     

Magnetic behavior of the oxide spinels: Li0.5Fe2.5−2x Al x Cr x O4

In order to study the effect of substitution of Fe³⁺ by Al³⁺ and Cr³⁺ in Li_0.5Fe_2.5O₄ on its structural and magnetic properties, the spinel system Li_0.5Al _x Cr _x Fe_2.5?2x O₄ (x=0.0, 0.2, 0.4, 0.5, 0.6 and 0.8) has been characterized by X-ray diffraction, high field magnetization, low field ac susceptibility and ⁵⁷Fe Mossbauer spectroscopy. Contrary to the earlier reports, about 50% of Al³⁺ is found to occupy the tetrahedral sites. The system exhibits canted spin structure and a central paramagnetic doublet was found superimposed on magnetic sextet in the Mössbauer spectra (x>0.5).     

Magnetic properties of substitutional solid solutions of nickel and iron hexacyanoferrate–hexacyanochromate

In order to evaluate the influence of substitution at the central metal ion position in transition hexacyanometallates in some detail, the magnetic studies were carried out on a series of solid solutions of metal hexacyanometallates of the composition M[Fe^II(CN)₆]_{1? x} [Cr^III(CN)₆] _x , where M?=?Ni^II and Fe^III. The temperature and field dependences of magnetization were studied using a superconducting quantum interference device magnetometer. The field dependence of the samples at 5?K shows a hysteresis behaviour. For M?=?Ni^II, the transition temperature increases with increase in the substitution of low-spin Fe(III) by Cr(III) in the hexacyanometallate unit. The saturation magnetization was found to decrease with increase in the iron concentration. The observed variation in the magnetic properties, such as the value of T _C and the nature of magnetic ordering, is attributed to the variation in the composition of the transition-metal ion in the coordination sphere of carbon. On the other hand, for M?=?Fe^III, the transition temperature and saturation magnetization remained almost unchanged, indicating that substitution at the carbon coordination site did not produce any change in the magnetic interaction among the transition-metal ions through the cyanide ions.     

Enhancement of initial permeability due to Mn substitution in polycrystalline Ni0.50−xMnxZn0.50Fe2O4

The structural and magnetic properties of Mn substituted Ni_0.50−xMn_xZn_0.50Fe₂O₄ (where x=0.00, 0.10 and 0.20) sintered at various temperatures have been investigated thoroughly. The lattice parameter, average grain size and initial permeability increase with Mn substitution. Both bulk density and initial permeability increase with increasing sintering temperature from 1250 to 1300 °C and above 1300 °C they decrease. The Ni_0.30Mn_0.20Zn_0.50Fe₂O₄ sintered at 1300 °C shows the highest relative quality factor and highest initial permeability among the studied samples. The initial permeability strongly depends on average grain size and intragranular porosity. From the magnetization as a function of applied magnetic field, M(H), it is clear that at room temperature all samples are in ferrimagnetic state. The number of Bohr magneton, n(μ_B), and Neel temperature, T_N, decrease with increasing Mn substitution. It is found that Mn substitution in Ni_0.50−xMn_xZn_0.50Fe₂O₄ (where x=0.20) decreases the Neel temperature by 25% but increases the initial permeability by 76%. Possible explanation for the observed characteristics of microstructure, initial permeability, DC magnetization and Neel temperature of the studied samples are discussed.     

Synthesis and characterization of Ni1−xCoxFe2O4 nanoparticles

Ni_1−xCo_xFe₂O₄ (x=0.6, 0.8 and 0.9) nanoparticles have been synthesized with various crystallite sizes depending on the thermal treatments and composition (cobalt content) using the sol-gel combustion method. The size of nanoparticles has been controlled by thermal treatment. On the other hand, the magnetic property of the ferrite has been controlled by changing the heat treatment. Morphology and particle sizes of Ni_1−xCo_xFe₂O₄ have been studied using atomic force microscopy (AFM) and transmission electron microscopy (TEM). The presence of functional group has been identified by Fourier Transform Infrared (FTIR) spectra. From TGA-DTA studies, the weight gains of Ni_1−xCo_xFe₂O₄ nanoparticles have been observed and it might be due to capping organic molecules with oxygen at temperatures above 200 °C. Magnetic properties of Ni_1−xCo_xFe₂O₄ particles have been analysed using VSM and it is found that saturation magnetization (M_s) has increased with particle size and has coercivity (H_c) increased initially and then decreased. The M_s and H_c values decreased with the increase of content of cobalt in Ni_1−xCo_xFe₂O₄.     

3:29型Gd-Fe-Co-Cr化合物的结构和磁性

制备了Gd₃(Fe_1-xCo_x)₂₅Cr₄(0≤x≤0.6)和Gd₃Fe_29-yCr_y(3.5≤x≤5.0)化合物,通过X射线衍射和磁性测量手段研究了它们的结构和磁性.实验表明这些化合物都属于A_2/m空间群.Cr含量增加导致居里温度下降,饱和磁化强度降低,磁晶各向异性场下降.Co替代Fe导致单胞体积收缩,居里温度升高,5K的饱和磁化强度在x=0.3左右达到极大值,磁晶各向异性在x=0.4附近由易面转变为易轴. 关键词：     

Magnetic properties of nanosized γ-Fe2O3 and α-(Fe2/3Cr1/3)2O3, prepared by thermal decomposition of heterometallic single-molecular precursor

Thermal decomposition of the trinuclear complex [Fe₂CrO(CH₃COO)₆(H₂O)₃]NO₃ at 300, 400 and 500 °C gave γ-Fe₂O₃ nanoparticles along with amorphous chromium oxide, while decomposition of the same starting compound at 600 and 700 °C led to the formation of α-(Fe_2/3Cr_1/3)₂O₃ nanoparticles. Size of γ-Fe₂O₃ nanoparticles, determined by X-ray diffraction, was in the range from 9 to 11 nm and increased with formation temperature growth. Average size of α-(Fe_2/3Cr_1/3)₂O₃ nanoparticles was about 40 nm and almost did not depend on the temperature of its formation. γ-Fe₂O₃ nanoparticles possessed superparamagnetic behavior with blocking temperature 180-250 K, saturation magnetization 29-35 emu/g at 5 K, 44-49 emu/g at 300 K and coercivity 400-600 Oe at 5 K. α-(Fe_2/3Cr_1/3)₂O₃ nanoparticles were characterized by low magnetization values (2.7 emu/g at 70 kOe). Such magnetic properties can be caused by non-compensated spins and defects present on the surface of these nanoparticles. The increase of α-(Fe_2/3Cr_1/3)₂O₃ formation temperature led to decrease of magnetization (being compared for the same fields), which may be caused by decrease of the quantity of defects or non-compensated spins (due to decrease of particles' surface).     

Advanced electrochemical performance of LiMn1.4Cr0.2Ni0.4O4 as 5 V cathode material by citric-acid-assisted method

Spinel LiMn₂O₄ and LiMn_1.4Cr_0.2Ni_0.4O₄ cathode materials were successfully synthesized by the citric-acid-assisted sol-gel method with ultrasonic irradiation stirring. The structure and electrochemical performance of the as-prepared powders were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), energy-dispersive X-ray (EDX) spectrometer, cyclic voltamogram (CV) and the galvanostatic charge-discharge test in detail. XRD shows that all the samples have high phase purity, and the powders are well crystallized. SEM exhibits that LiMn_1.4Cr_0.2Ni_0.4O₄ has more uniform cubic-structure morphology than that of LiMn₂O₄. EDX reveals that a small amount of Mn³⁺ still exists in LiMn_1.4Cr_0.2Ni_0.4O₄. The galvanostatic charge-discharge test indicates that the initial discharge capacities for the LiMn_1.4Cr_0.2Ni_0.4O₄ and LiMn₂O₄ at 0.15 C discharge rates are 130.8 and 130.2 mAh g⁻¹, respectively. After 50 cycles, their capacity are 94.1% and 85.1%, respectively. The CV curve implies that Ni and Cr dual substitutions are beneficial to the reversible intercalation and deintercalation of Li⁺, and suppress Mn³⁺ generation at high temperatures and provide improved structural stability.     

Structure and magnetostriction of Tb0.4Nd0.6(Fe0.8Co0.2) x alloys

Structural, magnetic and magnetostrictive properties of Tb_0.4Nd_0.6(Fe_0.8Co_0.2) _x (1.50 ≤ x ≤ 1.90) alloys have been investigated by means of X-ray diffraction (XRD), a vibrating sample magnetometer and a standard strain technique. XRD analysis shows the presence of single Laves phase with a cubic MgCu₂-type structure for the high Nd content alloy around the composition of x = 1.80, which tends to be formed by curing at relatively low annealing temperature. The easy direction of magnetization at room temperature is observed toward <111> axis, accompanied by a rhombohedral distortion with a large spontaneous magnetostriction λ₁₁₁. An optimized effect on the linear anisotropic magnetostriction, 360 ppm at 3 kOe, was observed for the high Nd content Tb_0.4Nd_0.6(Fe_0.8Co_0.2)_1.80 alloy, which can be attributed to its single Laves phase, the large λ₁₁₁ (~1,520 ppm) of the MgCu₂-type (Tb,Nd)(Fe,Co)₂ phase and the good soft magnetic behaviors.