一种基于外差探测的光纤Bragg光栅温度传感器

提出了一种基于光纤Bragg光栅的温度传感器，阐述了光纤Bragg光栅的温度传感机理，用2个相同的光纤Bragg光栅构成折叠式Mach Zehnder(M Z)干涉仪，其中一个光栅作为参考臂，另一个作为传感臂：采用外差探测技术来测量外界的温度物理量。当温度发生变化，Bragg光栅的波长也随之改变。外差探测用来探测传感臂和参考臂由于温度变化引起的输出信号的频率差异。对其动态测量范围和灵敏度也进行了分析。     

利用调谐滤波技术的光纤光栅复用传感器

采用光纤光栅悬臂梁线性调谐技术 ,提出了利用调谐滤波技术对光纤光栅复用传感信号进行检测的方案 ,在分析其基本工作原理的基础上 ,实验研究了其波分复用传感特性 ,传感测量的结果与光谱分析仪直接测量的结果基本一致。传感器的波长分辨率主要取决于系统的最小可探测光功率 ,由于采用了高灵敏度的光电测量系统 ,传感测量的波长分辨率可达 0 .0 0 5nm ,应变分辨率可达 5.7× 10 - 6 。     

FBG多功能传感系统集成与应用

为充分发挥光纤光栅(FBG)传感系统复用能力,可同时对传感光路各个传感器的光信号进行有效识别,且为传感器设计和加工提供依据,基于FBG传感原理,从系统集成及复用能力优化的角度,探讨波分复用传感器设计方法,以及节点传感器结构和灵敏度设计原则与标准,并将提出的原则等应用于某实际工程光纤监测系统。传感系统在运行过程中,获得了较为可靠的监测数据,分布式光纤和点式电测技术测试结果相差6%左右,进一步表明临近光纤传感器没有出现传感信号串扰现象,为工程施工和安全维护提供参照。     

新型光纤光栅水声传感器的研究

提出了一种新型的光纤布拉格光栅(FBG)水声传感探头结构以及光纤光栅传感信号的自解调方法。利用一对匹配光栅构成推挽结构,实现了传感-解调的合二为一,大大地减小了系统的复杂度;并通过筒状弹性体结构,解决了裸光纤光栅测量水声信号的灵敏度过小的问题,并具有温度补偿作用。仿真与初步实验结果表明,该水听器探头的测量动态范围超过100 dB,在100~200 dB re 1μPa的水声压范围内,测量灵敏度为0.36 nm/Mpa。     

具有温度自校准功能的光纤折射率传感器

提出一种具有温度自校准功能的光纤折射率（RI）传感器,传感头结构由2段很短的多模光纤（MMF）之间夹熔一段对折射率不敏感的光纤布拉格光栅（FBG）构成,传感头总长度为14 mm,FBG可以为折射率测量提供良好的温度校准功能。实验结果证明,该传感器的折射率灵敏度为126 nm。其干涉光谱共振波长的温度灵敏度为35.09 pm/℃,用于温度校准的FBG的温度灵敏度为11.14 pm/℃。相比于普通的折射率传感器,这种具有温度自校准功能的折射率传感器具有良好的实用前景。     

Heterodyne detection for Fiber Bragg Grating sensors

In this paper, we present a Fiber-Bragg-Grating-based temperature sensor. The technique employs heterodyne detection using two Fiber Bragg Gratings. One of the gratings is used as a reference (local oscillator) and the second as a sensing arm. This sensor uses a Folded Mach-Zehnder interferometer. As the temperature changes, the Bragg wavelength of the FBG shifts. The heterodyne detection is used to detect the frequency difference between the reference and sensing signals that is caused by the temperature change. The dynamic range and sensitivity of the sensor were analyzed and presented.     

Instantaneous frequency measurement using two parallel I/Q modulators based on optical power monitoring

A scheme for instantaneous frequency measurement(IFM)using two parallel I/Q modulators based on optical power monitoring is proposed.The amplitude comparison function(ACF)can be constructed to establish the relationship between the frequency of radio frequency(RF)signal and the power ratio of two optical signals output by two I/Q modulators.The frequency of RF signal can be derived by measuring the optical power of the optical signals output by two I/Q modulators.The measurement range and measurement error can be adjusted by controlling the delay amount of the electrical delay line.The feasibility of the scheme is verified,and the corresponding measurement range and measurement error of the system under different delay amounts of the electrical delay line are given.Compared with previous IFM schemes,the structure of this scheme is simple.Polarization devices,a photodetector and an electrical power meter are not used,which reduces the impact of the environmental disturbance on the system and the cost of the system.In simulation,the measurement range can reach 0 GHz-24.5 GHz by adjusting the delay amount of the electrical delay lineτ=20 ps.The measurement error of the scheme is better at low frequency,and the measurement error of low frequency 0 GHz-9.6 GHz can reach-0.1 GHz to+0.05 GHz.     

基于F-P腔和FBG的强度调制型光纤液位传感器

设计了一种用于液位测量的光纤F-P(Fabry-Perot)传感器,并从传感头的设计制作出发,讨论了提高传感器输出信号对比度的方法;测量系统采用宽带光源,解调时经FBG(Fiber Bragg Grating)反射和透射得到传感信号和参考信号,对两路光强信号进行联合处理,补偿了光源功率波动和光路损耗变化引起的不良影响,消除了强度调制型传感器的固有缺点,此方法具有结构简单、成本低的优点;该系统可进行连续测量,测量范围为0到200kPa,相当于测量水深0到20m,其分辨力小于1cm(水面高度变化),特别适合对易燃易爆的环境中的油库液位进行测量。     

Interrogation technique for a fiber Bragg grating sensing array based on a Sagnac interferometer and an acousto-optic modulator

We propose and experimentally demonstrate a novel real-time interrogation technique for a fiber Bragg grating (FBG) sensing system that is based on a frequency-shifted asymmetric Sagnac interferometer. FBG sensors are connected to the Sagnac loop by an optical coupler, and an acousto-optic modulator (AOM) is asymmetrically placed in the Sagnac loop. By linearly sweeping the driving frequency of the AOM, the environmental variation around each FBG sensor can be determined by measuring the spectrum of the interference signals of the two counterpropagating light beams reflected by the corresponding FBG. The system has the advantages of low cost and real-time sensing.     

Investigation of PZT driven tunable optical filter nonlinearity using FBG optical fiber sensing system

The nonlinearity of a piezo-electrical transducer (PZT) driven tunable optical filter (TOF) is investigated and evaluated using FBG optical fiber sensing system including a broadband optical source and a tunable laser (TL) with a group of fiber Bragg gratings (FBGs). Polynomial fit is adopted to model the nonlinearity. Under three-order polynomial fit, the random error in wavelength measurement using this TOF and a reference FBG is minimized to be below 20 pm. At the same time, the absolute error in wavelength measurement is kept below 0.25 nm. Under four-order or higher polynomial fit, a sharp increase of the random measurement error is observed. This research reveals the possibility of using PZT driven TOFs in optical spectroscopy where high resolution, high-accuracy, and fast time-response is required.     

基于光纤环形激光器和光放大的100 km光纤布拉格光栅传感系统

在基于掺铒光纤-拉曼混合放大的可调光纤环形激光器的光纤布拉格光栅(FBG)传感系统结构基础上,提出了延长传感距离的新方法。该方法以环形掺铒光纤激光器作为光源,采用双波长拉曼放大的方法对信号进行低噪声的双向放大,系统中间的两段掺铒光纤再利用剩余的抽运功率产生自发辐射光和放大传感信号,使得整个系统能够在超长的传感距离上获得很高的信噪比。实验表明使用一只40 mW的掺铒光纤放大(EDFA)抽运源、一只170 mW的拉曼抽运源和一只2 W的拉曼抽运源,可以使整个系统的传感距离达到100km,并且传感系统的光纤布拉格光栅反射信号均能获得超过57 dB的优良信噪比,从而实现在超长距离上的光纤布拉格光栅传感。     

分布式反馈激光器动态扫描光纤布拉格光栅波长解调系统

通过对该系统采集到的法布里-珀罗(F-P)标准具透射谱和光纤布拉格光栅(FBG)传感器反射谱进行寻峰算法以及拟合算法的研究,采用C语言编程和LabVIEW编程相结合的方式,实现了FBG波长信号的解调。其中,由于系统采集到的F-P透射谱和FBG反射谱线时域信号数据都由离散点构成,且在3dB带宽内均符合高斯曲线分布,采用高斯拟合对采集到的信号数据进行寻峰处理,提高系统精度;又由于分布式反馈(DFB)激光器的波长扫描存在着一定的非线性,采用二项式拟合对DFB激光器的波长扫描曲线进行拟合,以降低其非线性导致的误差。另外,设置一路标准FBG传感通道用于波长校准。实验研究表明该系统稳定性良好,波长测量范围为1 550.012~1 554.812nm,分辨力为1pm,精度为±10pm,验证了该系统可用于FBG波长信号检测的可行性。     

基于边缘解调技术的光纤光栅波登管压力传感器的研制

研制了光纤光栅弹簧管压力传感器,并与双边缘解调技术相结合搭建了基于边缘解调技术的光纤压力传感器检测系统,对传感器和解调器的性能进行了测试,给出了实验结果.压力灵敏度为0.33nm/MPa,解调系统线性拟合度为0.99977,系统压力测量分辨率可达0.01MPa.     

基于WO3- Pd复合膜的D型光纤光栅氢气传感器

采用磁控溅射方法在侧边抛磨的光纤光栅（D型光纤光栅）上溅射40 nm WO3-Pd复合薄膜,制作了D型光纤光栅氢气传感器.40 nm WO3-Pd复合薄膜是由5 nm的WO3、5 nm的WO3/Pd混合膜和30 nm的Pd 薄膜组成.实验中,首先采用射频溅射技术向D型光纤光栅溅射5 nm WO3薄膜,再利用共溅射技术溅射5 nm WO3/Pd混合膜,最后用直流溅射技术溅射30 nm的Pd薄膜.SEM结果显示在多次通氢气后WO3-Pd薄膜仍然具有较好的表面形貌,这说明WO3-Pd复合薄膜具有较好的机械性能.实验结果表明:该氢气传感器具有较好的重复性,同镀有同样氢气敏感膜的普通FBG相比,D型光纤光栅的灵敏度提高了200%|在氢气体积浓度为6%时,D型光纤光栅传感器的波长变化为15pm.     

分布式光纤Bragg光栅波长校准方法

提出了一种利用标准参考光谱进行波长校准的方法。实验中利用由宽带光源和光纤可调谐滤波器组成的可调谐光源分别扫描了参考光谱和传感光栅的光谱。在参考通道,ITU标准参考模块的输出是具有固定波长的梳状光谱。利用高斯拟合算法计算出由标准参考透射谱峰值输出的对应的驱动电压,通过样条插值函数获得了滤波器输出波长与驱动电压的关系。计算光栅反射谱峰值对应的驱动电压,利用上面获得的滤波器输出波长与驱动电压的关系式可以计算出传感光栅的Bragg波长。实验结果表明,在较大的波长范围内实现了对多个传感光栅的波长校准,减小了由滤波器非线性输出造成的测量误差,具有较高的重复性。     

基于光纤微结构加工和敏感材料物理融合的光纤传感技术

将功能敏感材料与光纤在物理层面进行有机融合,充分发挥光纤传感器在结构集成、材料集成等方面的优势,将有望发展新型的光纤传感器件和系统.本文综述了飞秒激光光纤微加工技术分别在标准的单模光纤和光纤光栅上制备微结构,再结合敏感材料制备技术,实现在物理层面上光纤传感器材料和结构的集成和融合,探索实现新型高性能的光纤传感新技术.     

Differential reflectometry of FBG sensors in the wide spectral range

The paper presents a reflectometric technique for interrogation of multiple fiber Bragg grating (FBG) sensors based on conventional optical time domain reflectometry (OTDR). The method proposed rests on the differential measurement of FBGs’ response to a short probing laser pulse. Implementation of differential measurement principle using several reference FBGs allowed us to eliminate the susceptibility of the system to intensity fluctuations as well as to increase the measurement range as compared to the previous developments. The experimental threshold sensitivity amounted to ∼50 microstrain with the measurement range being defined by the number of reference FBGs and limited only by optical fiber tensile strength. Due to its simplicity, efficiency and usage of conventional OTDR equipment the proposed FBG interrogation technique can find a wide range of applications dealing with strain and temperature measurements.     

Temperature-insensitive transverse load sensing with improved accuracy using stress induced birefringence effects of fiber Bragg grating

Different from the basic sensing theory of the fiber Bragg grating (FBG) sensors based on direct spectral analysis, a new method exploiting the polarization properties of FBG for temperature-insensitive transverse load sensing is proposed. In this paper, the birefringence effects on FBG under transverse load are analyzed. The evolution of the polarization dependent loss (PDL) of FBG with wavelength for the transmitted signals with respect to the transverse load is also studied theoretically and experimentally. We proposed utilizing the PDL evolution of FBG to precisely recover the wavelength spacing between the two peaks of x-mode and y-mode for accurate transverse load measurement. Good agreements between experimental results and numerical simulations had been obtained.     

Quantitative MR renography using a calibrated internal signal (ERETIC)

To measure MR renograms, cortical and medullary kidney signal intensity evolution is followed after contrast agent injection. To obtain an accurate quantitative signal measurement, the use of a reference signal is necessary to correct the potential MRI system variations in time. The ERETIC method (Electronic Reference To access In vivo Concentrations) provides an electronic reference signal. It is synthesized as an amplitude modulated RF pulse applied during the acquisition. The ERETIC method was as precise as the external tube reference method but presents major advantages like its free adjustability (shape, location and magnitude) to the characteristics of the organ studied as well as its not taking room inside the magnet. Even though ERETIC showed a very good intrinsic stability, systems' variations still affect its signal in the same way as real NMR signals are affected. This method can be easily implemented on any imaging system with two RF channels.     

Impact of interferometer delay time on the performance of ODSB-SC RoF system with wavelength interleaving

In this paper, we investigate the impact of interferometer delay time in a 5 Gb/s optical double sideband-suppressed carrier (ODSB-SC) RoF system transmitting two wavelength interleaved radio frequency (RF) signals at 10 and 15 GHz over an optical fiber. Here, an optical Mach–Zehnder modulator is used for both optical carrier suppression and signal modulation. At the receiver, delay interferometer is used for the separation of RF frequency signals. We analyze the performance of the RoF system by varying the value of delay time of interferometer from 0.02 to 0.14 ns. The result shows that the RoF system performance is optimum for the time delay of 0.1 ns. Further, the optical spectrums, RF spectrums and eye diagrams of two interleaved RF signals have been compared.