超声喷雾方法制备低辐射玻璃

利用超声喷雾方法在玻璃基板上喷涂SnO2：F薄膜，制备了低辐射玻璃(Low-E玻璃)．通过光谱测量，得到其可见光透过率为85％以上，在近红外波段出现高反射．利用四探针测量仪，测量其面电阻在2Ω／cm^2以下．扫描电镜测量结果表明膜的均匀性较好，平均颗粒直径约在50nm．利用等离子体截止波长理论，解释了低辐射玻璃红外反射的物理机制．     

Sb，In，P掺杂对SnO_2薄膜透明导电性能的影响(英文)

采用溶胶凝胶(Sol-Gel)技术制备了SnO2:(Sb,In)透明导电薄膜,优化了制备工艺参数,获得了最佳制备条件,研究表明,4%的铟掺杂有效地改善了薄膜的内部结构,使得紫外-可见光的透过率显著增加;7%的锑掺杂释放出了更多的载流子,使薄膜的方块电阻降低,2%的磷掺杂因准连续杂质能带的形成进一步提高了薄膜的电导率.Sb、In、P的掺入使得SnO2薄膜的紫外-可见光的透过率达83%,方块电阻达38Ω/□     

氧氩比对SnO2/Ag/SnO2透明导电膜光电性能的影响

在室温及不同的氧氩比条件下,采用射频磁控溅射Ag层和直流磁控溅射SnO2层,在载玻片衬底上制备出了SnO2/Ag/SnO2多层薄膜.用霍尔效应测试仪、四探针电阻测试仪和紫外-可见-近红外光谱仪等表征了薄膜的电学性质和光学性质.实验结果表明:当氧氩比为1:14时,所制得的薄膜的光电性质优良指数最大,为1.69×10-2 Ω-1;此时,薄膜的电阻率为9.8×10-5Ω·cm,方电阻为9.68Ω/sq,在400～800 nm可见光区的平均光学透射率达85％;并且,在氧氩比为1:14时,利用射频磁控溅射Ag层和直流磁控溅射SnO2层在PET柔性衬底上制备出了光电性质优良的柔性透明导电膜,其在可见光区的平均光学透过率达85％以上,电阻率为1.22×10-4Ωcm,方电阻为12.05Ω/sq.     

Sb，In，P掺杂对SnO2薄膜透明导电性能的影响

采用溶胶凝胶（Sol-Gel）技术制备了SnO2：（Sb，In）透明导电薄膜，优化了制备工艺参数，获得了最佳制备条件．研究表明，4％的铟掺杂有效地改善了薄膜的内部结构，使得紫外-可见光的透过率显著增加；7％的锑掺杂释放出了更多的栽流子，使薄膜的方块电阻降低，2％的磷掺杂因准连续杂质能带的形成进一步提高了薄膜的电导率．Sb、In、P的掺入使得SnO2薄膜的紫外-可见光的透过率达83％，方块电阻达38Ω。     

Sr-F共掺杂的SnO2基透明导电薄膜

利用离子源辅助的电子束热蒸发技术研制了高性能的Sr-F共掺杂SnO2( SFTO)基透明导电薄膜。所制备的SFTO薄膜具有良好的导电性和透过率,电阻率低于3.9×10-3Ω·cm,380~2500 nm波段的平均透过率大于85%,功函数约为5.10 eV。 SFTO透明导电薄膜为非晶态薄膜,具有较好的表面平整度( Rq <1.5 nm)。与工业上F掺杂SnO2薄膜的衬底温度(>450℃)相比,本文所用的衬底温度仅为300℃,有望直接将SnO2基透明导电非晶薄膜制备到柔性的塑料( PI、PAR或PCO)衬底上以获得性能良好的柔性电极。     

图谱分析退火对本征SnO2多晶薄膜性能的影响

提高CdTe太阳电池转换效率的有效途径之一是适当减薄CdS窗口层,减薄了的CdS层会严重影响电池性能,解决方法是在窗口层和透明导电膜之间加一层高阻本征SnO2薄膜。采用反应磁控溅射制备了具有高阻抗的本征SnO2薄膜,并对其进行了后处理,利用XRD,XPS等方法研究了退火前后薄膜的结构,成分及表面化学状态的变化。结果表明:经N2/O2=4:1气氛550℃(0.5h)退火后,样品由非晶态转变为四方相结构的多晶薄膜,具有(110)择优取向;XPS分析表明退火后薄膜的氧含量增加、O(1s)峰向低能方向移动,SnO被氧化成SnO2,使得薄膜的透过率增大,退火后的本征SnO2高阻膜非常适合作为过渡层应用于CdTe太阳电池中。     

蓝宝石衬底SnO2:Sb薄膜的制备及结构和光致发光性质

用射频磁控溅射法在蓝宝石(0001)衬底上制备出锑掺杂的氧化锡(SnO2:sb)薄膜.对制备薄膜的结构和发光性质进行了研究.制备样品为多晶薄膜,具有纯SnO2的四方金红石结构.室温条件下对样品进行光致发光测量,在334 nm附近观测到紫外发射峰,并对SnO2:Sb的光致发光机制进行了研究.     

有机衬底SnO2:Sb透明导电膜的制备与特性研究

常温下,采用射频磁控溅射法在有机的柔性衬底上制备出了SnO2:Sb透明导电膜,并对薄膜的结构和光电性质进行了研究.制备的样品为多晶薄膜,并且保持了二氧化锡的金红石结构.性能良好的薄膜电阻率为6.5×10-3Ω·cm,载流子浓度为1.2×1020cm-3,霍耳迁移率是9.7cm2·V-1·s-1.薄膜在可见光区的平均透过率达到了85%. 关键词： 柔性衬底 SnO2:Sb透明导电膜 射频磁控溅射法     

CdTe多晶薄膜沉积制备及其性能

在氩气和氧气混合气氛下,近空间升华法制备了CdTe多晶薄膜。薄膜的结构、性质决定于整个沉积过程。深入研究沉积过程中的热交换、物质输运,有助于获得结构致密具有良好光电性质的CdTe薄膜。分析了近空问沉积的物理机制,测量了近空间沉积装置内的温度分布,讨论了升温过程、气压与薄膜的初期成核的关系。结果表明,不同气压下制备的样品,均有立方相CdTe。此外,还有CdS和SnO2：F衍射峰。CdTe晶粒随气压增加有减小趋势;随气压的增加,透过率呈下降趋势,相应的CdTe吸收边向短波方向移动。采用衬底温度500℃,源温度620℃,在120℃的温差下,沉积时间4min上制备CdTe多晶薄膜,获得转换效率优良的结构为SnO2：F／CdS／CdTe／Au的集成电池。     

二氧化钒薄膜的低温制备及其性能研究

针对VO₂薄膜在微测辐射热计上的应用，采用射频反应溅射法，在室温下制备氧化钒薄膜；研究了氧分压对薄膜沉积速率、电学性质及成分的影响.通过调节氧分压，先获得成分接近VO₂的非晶化薄膜，再在400℃空气中氧化退火，便可制得高电阻温度系数，低电阻率的VO₂薄膜，电阻温度系数约为-4%/℃，薄膜方块电阻为R_□为100—300kΩ；薄膜在室温下沉积，400℃下退火的制备方法与微机电加工(micro electromechanic 关键词： 二氧化钒 电阻温度系数 氧分压 射频反应溅射法     

The role of hydrogen in hydrogenated microcrystalline silicon film and in deposition process with VHF-PECVD technique

The role of hydrogen in hydrogenated microcrystalline silicon ($\mu $c-Si:H) thin films in deposition processes with very high frequency plasma-enhanced chemical vapour deposition (VHF-PECVD) technique have been investigated in this paper. With \textit{in situ} optical emission spectroscopy (OES) diagnosis during the fabrication of $\mu $c-Si:H thin films under different plasma excitation frequency $\nu _{\rm e }$ (60MHz--90MHz), the characteristic peak intensities ($I_{{\rm SiH}^*}$, $I_{{\rm H}\alpha^*}$ and $I_{{\rm H}\beta ^*}$) in SiHVHF-PECVD技术 氢化微晶硅 光发射光谱 薄膜学VHF-PECVD technique, hydrogenated microcrystalline silicon, role of hydrogen, optical emission spectroscopyProject supported by the Natural Science Foundation of Guangdong Province, China (Grant No 05300378), the State Key Development Program for Basic Research of China (Grant Nos G2000028202 and G2000028203) and the Program on Natural Science of Jinan University, Guangzhou, China (Grant No 51204056).2005-11-252005-11-252006-01-05The role of hydrogen in hydrogenated microcrystalline silicon （μc-Si：H） thin films in deposition processes with very high frequency plasma-enhanced chemical vapour deposition （VHF-PECVD） technique have been investigated in this paper. With in situ optical emission spectroscopy （OES） diagnosis during the fabrication of μc-Si：H thin films under different plasma excitation frequency Ve （60MHz-90MHz）, the characteristic peak intensities （IsiH＊, IHα＊ and IHβ＊ ） in SiH4＋H2 plasma and the ratio of （IHα＊ ＋ IHβ＊ ） to IsiH＊ were measured; all the characteristic peak intensities and the ratio （IHα＊ ＋ IHβ＊ ）/IsiH＊ are increased with plasma excitation frequency. It is identified that high plasma excitation frequency is favourable to promote the decomposition of SiH4＋H2 to produce atomic hydrogen and SiHx radicals. The influences of atomic hydrogen on structural properties and that of SiHx radicals on deposition rate of μc-Si：H thin films have been studied through Raman spectra and thickness measurements, respectively. It can be concluded that both the crystalline volume fraction and deposition rate are enhanced with the increase of plasma excitation frequency, which is in good accord with the OES results. By means of FTIR measurements, hydrogen contents of μc-Si：H thin films deposited at different plasma excitation frequency have been evaluated from the integrated intensity of wagging mode near 640 cm^-1. The hydrogen contents vary from 4% to 5%, which are much lower than those of μc-Si：H films deposited with RF-PECVD technique. This implies that μc-Si：H thin films deposited with VHF-PECVD technique usually have good stability under light-soaking.     

A new analysis of the ν2 fundamental band of H2O^＋＊

This paper reports that the absorption spectra of H2O^＋ have been measured by tunable mid-infrared diode laser spectroscopy in the spectral range of 1100-1380 cm^-1. The H2O＋ ions are generated in an AC glow discharge of the gaseous mixtures of H2O/He and detected with the velocity modulation technique. Forty new lines are assigned to the ν2 fundamental band of H2O^＋ （X^2B1）. The observed lines together with other data published previously are fitted to the standard effective Hamiltonian of an asymmetric top, yielding a set of improved rotational constants, spin-rotation constants and their quartic and sextic centrifugal distortion constants for the ν2=1 vibrational state of H2O＋.     

Optical emission spectroscopy study on depositionprocess of microcrystalline silicon

This paper reports that the optical emission spectroscopy (OES) is used to monitor the plasma during the deposition process of hydrogenated microcrystalline silicon films in a very high frequency plasma enhanced chemical vapour deposition system. The OES intensities (SiH\sj{*}, H微晶硅 VHF-PECVD 发射光谱学 薄膜物理学microcrystalline silicon, VHF-PECVD, optical emission spectroscopy2005-11-092005-11-092005-12-12This paper reports that the optical emission spectroscopy （OES） is used to monitor the plasma during the deposition process of hydrogenated microcrystalline silicon films in a very high frequency plasma enhanced chemical vapour deposition system. The OES intensities （Sill^＊, H^＊ and H^＊β） are investigated by varying the deposition parameters. The result shows that the discharge power, silane concentrations and substrate temperature affect the OES intensities. When the discharge power at silane concentration of 4% increases, the OES intensities increase first and then are constant, the intensities increase with the discharge power monotonously at silane concentration of 6%. The SiH^＊ intensity increases with silane concentration, while the intensities of H^＊α and H^＊β increase first and then decrease. When the substrate temperature increases, the SiH^＊ intensity decreases and the intensities of H^＊α and H^＊β are constant. The correlation between the intensity ratio of IH^＊α/ISiH^＊ and the crystalline volume fraction （Xc） of films is confirmed.     

The fabrication of nickel silicide ohmic contacts to n-type 6H-silicon carbide

This paper reports that the nickel silicide ohmic contacts to n-type 6H-SiC have been fabricated. Transfer length method test patterns with NiSi/SiC and NiSi硅化镍;欧姆触点;n型碳化硅;制造;能带;带隙Project supported by the National Basic Research Program of China (Grant No~2002CB311904), the National Defense Basic Research Program of China (Grant No~51327010101) and the National Natural Science Foundation of China (Grant No~60376001).2006-09-192006-10-30This paper reports that the nickel silicide ohmic contacts to n-type 6H-SiC have been fabricated. Transfer length method test patterns with NiSi/SiC and NiSi2/SiC structure axe formed on N-wells created by N^＋ ion implantation into Si-faced p-type 6H-SiC epilayer respectively. NiSi and NiSi2 films are prepared by annealing the Ni and Si films separately deposited. A two-step annealing technology is performed for decreasing of oxidation problems occurred during high temperature processes. The specific contact resistance Pc of NiSi contact to n-type 6H-SiC as low as 1.78× 10^-6Ωcm^2 is achieved after a two-step annealing at 350 ℃for 20 min and 950℃ for 3 min in N2. And 3.84×10-6Ωcm^2 for NiSi2 contact is achieved. The result for sheet resistance Rsh of the N＋ implanted layers is about 1210Ω/□. X-ray diffraction analysis shows the formation of nickel silicide phases at the metal/n-SiC interface after thermal annealing. The surfaces of the nickel silicide after thermal annealing are analysed by scanning electron microscope.     

Density functional study on chirospectra of hydrogen-bonded systems X-（H2O）3（X=F,Cl,Br,I）

This paper calculates the molecular structures,infrared,Raman,circular dichroism spectra and optical rotatory powers of some hydrogen-bonded supramolecular systems as a cyclic water trimer,(H2O)3 and its pyramidal halide complexes,X-(H2O)3(X = F,Cl,Br,I) with the gradient-corrected density functional theory method at the B3LYP/6-311++G(2d,2p) and B3LYP/Aug-cc-pVTZ levels.It finds that the complexation of halide anions with the water trimer can efficiently modulate the chirally optical behaviors.The calculated vibrational circular dichroism spectrum illuminates that the vibrational rotational strength of S(+)-(H2O)3 mostly originates from the O-H rocking modes,whereas chirality of S(-)-X-(H2O)3(X = F,Cl,Br,I) has its important origin in the O-H stretching modes.The calculated optical rotatory power demonstrates that S(+)-(H2O)3 and S(+)-F(H2O)3 are positively chiral,whereas S(-)-X-(H2O)3(X = Cl,Br,I) are negatively chiral.With the polarizable continuum model,calculated bulk solvent effect in the solvents water and carbontetrachloride and argon shows that the positive chirality of S(+)-(H2O)3 is enhanced and the negative chirality of S(-)-X-(H2O)3(X = Cl,Br,I) and the positive chirality of S(+)-F(H2O)3 are reduced with an augmentation of the solvent dielectric constant.     

Novel material for nonvolatile ovonic unified memory (OUM)－Ag11In12Te26Sb51 phase change semiconductor

In this paper, Ag_{11}In_{12}Te_{26}Sb_{51} phase change semiconductor films have been prepared by dc sputtering. The crystallization behaviour of amorphous Ag_{11}In_{12}Te_{26}Sb_{51} thin films was investigated by using differential scanning calorimetry and x-ray diffraction. It was found that the crystallization temperature is about 483K and the melting temperature is 754.8K and the activation energy for crystallization, E_a, is 2.07eV. The crystalline Ag_{11}In_{12}Te_{26}Sb_{51} films were obtained using initializer. The initialization conditions have a great effect on the sheet resistance of Ag_{11}In_{12}Te_{26}Sb_{51} films. We found that the effect of the initialization condition on the sheet resistance can be ascribed to the crystallinity of Ag_{11}In_{12}Te_{26}Sb_{51} films. The sheet resistance of the amorphous (R_{amo}) film is found to be larger than 1×10^6Ω and that of the crystalline (R_{cry}) film lies in the range from about 10^3 to 10^4Ω. So we have the ratio R_{amo}/R_{cry}=10^2～10^3, which is sufficiently large for application in memory devices.     

Analysis of Dα（Hα） spectrum emitted in front of the limiter in HT-7^＊

In order to understand the recycling and emission processes of hydrogen atoms in HT 7, spectral profiles of the Dα（Hα） line emitted in front of the limiter have been observed with a high-resolution spectrometer and simulated by using the neutral particle transport code DEGAS 2. The results show that four processes are necessary to interpret the Dα（Hα） line shape： 1） atom desorption, 2） molecular dissociation, 3） particle reflection, and 4） charge-exchange. The products of the first two processes are cold atoms which emit photons near the peak of Dα（Hα） line shape, and those from the last two are warm atoms contributing to the blue side of the spectrum. For a typical ohmic discharge （shot 68520 ne（0） ≈ 3× 10^19 m^-3. these components contribute 32%, 15%, 32% and 21%, respectively. Dα（Hα） line shapes under different plasma parameters are also discussed in this paper.     

Enhanced optical nonlinear absorption of graded Au--TiO2 composite films

This paper reports that single-layer and graded Au-TiO2 granular composite films with Au atom content 15%- 66% were prepared by using reactive co-sputtering technique. The third-order optical nonlinearity of single-layer and graded composite films was investigated by using s- and p-polarized Z-scans in femtosecond time scale. The nonlinear absorption coefficient βeff of single-layer Au-TiO2 films is measured to be -2.3×10^3-0.76×10^3 cm/GW with Au atom content 15%-66%. The βeff value of the 10-layer Au-TiO2 graded film is enhanced to be -2.1×10^4cm/GW calculated from p-polarized Z-scans, which is about ten times the maximum βeff of single-layer films. Broadened response in the wavelength region 730-860 nm of the enhanced optical nonlinearity of graded Au-TiO2 composite films was also investigated.     

Nanosecond-time-resolved infrared spectroscopic study of fast relaxation kinetics of protein folding by means of laser-induced temperature-jump

Elucidating the initial kinetics of folding pathways is critical to the understanding of the protein folding mechanism. Transient infrared spectroscopy has proved a powerful tool to probe the folding kinetics. Herein we report the construction of a nanosecond laser-induced temperature-jump （T-jump） technique coupled to a nanosecond timeresolved transient mid-infrared （mid-IR） spectrometer system capable of investigating the protein folding kinetics with a temporal resolution of 50 ns after deconvolution of the instrumental response function. The mid-IR source is a liquid N2 cooled CO laser covering a spectral range of 5.0μm （2000 cm^-1）-6.5μm （1540 cm^-1）. The heating pulse was generated by a high pressure H2 Raman shifter at wavelength of 1.9μm. The maximum temperature-jump could reach as high as 26±1℃. The fast folding/unfolding dynamics of cytochrome C was investigated by the constructed system, providing an example.     

Observation of four-wave mixing in caesium atoms using a noncycling transition

In this paper the generation of four-wave mixing (FWM) signal using a noncycling transition of caesium atoms is investigated when the pumping laser is locked to the transition $6{\rm S}_{1/2}F=4\to6{\rm P}_{3/2}F'=4$, and meanwhile the probe frequency is scanned across the $6{\rm S}_{1/2}F=4 \to6{\rm P}_{3/2}$ transition. The efficiency of the four-wave mixing signal as a function of the intensity of the pumping beams and the detuning of the pumping beams is also studied. In order to increase the detection efficiency, a repumping laser which is resonant with $6{\rm S}_{1/2} F=3\to 6{\rm P}_{3/2}F'=4$ transition is used. A theoretical model is also introduced, and the theoretical results are in qualitative agreement with experimental ones.