Determination of retention indices in LPTGC

Summary A method is presented for the calculation of retention indices in linear programmed-temperature gas chromatography (LPTGC) on the basis of isothermal retention data and the operating conditions (initial temperature, programming rate, gas flow velocity) of the run. Part IV of a series; parts I, II and III see refs. [1], [2] and [3].     

Relationship between thermodynamic characteristics and isothermal retention indices

Summary Thermodynamic characteristics determined from retention data measured under isothermal conditions were used for the calculation of retention indices of a number of model compound. The minimum retention index difference required for the identification of two adijacent compounds as well the temperature dependency of retention index are discussed. The possibility of alculating thermodynamic characteristics from retention indices published in the literature was also investigated.Dedicated to Professro J. F. K. Huber on the occasion of his 60th birthday.     

Cubic splines compared with other methods for the calculation of programmed temperature retention indices

Summary Program temperature retention indices for fifteen nonalkane solutes have been determined by cubic splines, by other procedures found in the literature and by interpolation of the n-alkanes retention time logarithm for eleven temperature programs. A comparison in terms of variance of the differences between PTRI calculated by CS and each of the remaining methods is made for each of the eleven program runs, for each of the three stationary phases used and for many of the programs. The smallest variances obtained result when the Zenkevich, van den Dool & Kratz and Chen et al. methods are tested. The stationary phase polarity is of no relevance since it has no effect on the specific PTRI found by the different methods employed in this work.     

Low-temperature heat capacity and thermodynamic properties of endo-Tricyclo[5.2.1.0]decane

Endo-Tricyclo[5.2.1.0^2,6]decane (CAS 6004-38-2) is an important intermediate compound for synthesizing diamantane. The lack of data on the thermodynamic properties of the compound limits its development and application. In this study, endo-Tricyclo[5.2.1.0^2,6]decane was synthesized and the low temperature heat capacities were measured with a high-precision adiabatic calorimeter in the temperature range from (80 to 360) K. Two phase transitions were observed: the solid-solid phase transition in the temperature range from (198.79 to 210.27) K, with peak temperature 204.33 K; the solid-liquid phase transition in the temperature range from 333.76 K to 350.97 K, with peak temperature 345.28 K. The molar enthalpy increments, ΔH_m, and entropy increments, ΔS_m, of these phase transitions are ΔH_m=2.57 kJ · mol⁻¹ and ΔS_m=12.57 J · K⁻¹ · mol⁻¹ for the solid-solid phase transition at 204.33 K, and, Δ_fusH_m=3.07 kJ · mol⁻¹ and Δ_fusS_m=8.89 J · K⁻¹ · mol⁻¹ for the solid-liquid phase transition at 345.28 K. The thermal stability of the compound was investigated by thermogravimetric analysis. TG result shows that endo-Tricyclo[5.2.1.0^2,6]decane starts to sublime at 300 K and completely changes into vapor when the temperature reaches 423 K, reaching the maximal rate of weight loss at 408 K.     

A fully automated adiabatic calorimeter for heat capacity measurement between 80 and 400 K

A fully automated adiabatic calorimeter controlled on line by a computer used for heat capacity measurements in the temperature range from 80 to 400 K was constructed. The hardware of the calorimetric system consisted of a Data Acquisition/Switch Unit, 34970A Agilent, a 7 1/2 Digit Nano Volt /Micro Ohm Meter, 34420A Agilent, and a P4 computer. The software was developed according to modern controlling theory. The adiabatic calorimeter consisted mainly of a sample cell equipped with a miniature platinum resistance thermometer and an electric heater, two (inner and outer) adiabatic shields, two sets of six junction differential thermocouple piles and a high vacuum can. A Lake Shore 340 Temperature Controller and the two sets of differential thermocouples were used to control the adiabatic conditions between the cell and its surroundings. The reliability of the calorimeter was verified by measuring the heat capacities of synthetic sapphire (α-Al₂O₃), Standard Reference Material 720. The deviation of the data obtained by this calorimeter from those published by NIST was within ±0.1% in the temperature range from 80 to 400 K.     

Relationship between enantioselectivity and solute structure on a chiral α1-acid glycoprotein column

Summary The relationship between the enantioselectivity, the retention and the solute structure for N-aminoalkylsuccinimides and 1-alkyl-2′,6′-pipecoloxylidides have been studied using α₁-acid glycoprotein as the chiral stationary phase. Both the enantioselectivity and the retention are highly affected by small changes of the solute structure in series of homologous compounds. For example, increasing the steric bulk on a basic aliphatic nitrogen improves the enantioselectivity. It was also demonstrated for the succinimides that the magnitude of the separation factor was highly affected by the distance between the basic nitrogen and the chiral center. The chiral selectivity was not lost for the succinimides despite the fact that the basic nitrogen was separated from the chiral center with seven atoms, which may be an effect of that these compounds contain more than one strong hydrogen bonding group. Substitution in the aromatic ring of the succinimides also influences both the retention and the chiral selectivity to a large extent. Electronegative substituents can increase the separation factor but introduction of an alkyl or an alkoxy group in the aromatic ring decreases the enantioselectivity for the succinimides.     

Aqueous solution of phosphoric acid as the stationary liquid phase for selective separation of fatty acids under conditions of steam chromatography

An aqueous solution of phosphoric acid was used as a selective stationary liquid phase for the separation of volatile fatty acids under conditions of steam chromatography. Organic acids C₂–C₈ are eluted from the column as symmetric peaks, and the order of their elution is reverse to that observed commonly on other phases. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 3, pp. 497–499, March, 1997.     

Synthesis of α,α′-bis(R-benzylidene)cycloalkanones catalyzed by potassium hydrogen sulfate under solvent-free conditions

Cyclopentanone or cyclohexanone were condensed with aromatic aldehydes to give corresponding α,α′-bis(R-benzylidene)cyclopentanones or α,α′-bis(R-benzylidene)cyclohexanones. The reaction was catalyzed by potassium hydrogen sulfate with a yield of 84–95% under solvent-free conditions.     

稀土掺杂Lu3Al5O12荧光粉的发光特性及能量传递

采用高温固相法制备了Ce、Sm共掺Lu_3Al_5O_(12)荧光粉。通过X射线衍射分析、荧光光谱分析研究了样品的结构、发光特性,并通过理论计算研究了能量传递效率、能量传递的临界距离以及能量传递方式。X射线衍射分析表明所制备的荧光粉具有单一的石榴石结构;荧光光谱分析表明,在464 nm蓝光激发下,Sm~(3+)的引入可增加Lu_3Al_5O_(12)∶Ce,Sm发射光谱中红光成分,并且随着Sm~(3+)浓度的增加,Ce~(3+)发光强度逐渐减弱。计算出Ce~(3+)、Sm~(3+)之间的能量传递效率高达77.42%,确定了Ce~(3+)、Sm~(3+)之间的能量传递机制为偶极-偶极相互作用。     

Ti4+掺杂制备花状SnO2/Sn3O4异质结微米球及其光催化性能

通过水热法制备了由层状纳米片堆叠而成的花球状Sn_3O_4及x%Ti-Sn O_2/Sn_3O_4(x%为Ti与Sn的物质的量之比)。采用X射线粉末衍射、扫描电子显微镜、透射电子显微镜、X射线光电子能谱、紫外-可见漫反射光谱、红外光谱和光电流响应等物理化学方法对合成的样品进行表征分析。结果表明,由于Ti~(4+)电负性及离子半径与Sn~(4+)相似,可以很好地进入Sn_3O_4晶格中替代Sn~(4+)形成替代掺杂,但不引起大的晶格畸变。同时,掺入Ti~(4+)后使得一部分Sn~(4+)直接与O结合生成纳米球状Sn O_2颗粒分散覆盖在Sn_3O_4表面,形成Sn O_2/Sn_3O_4异质结。光催化活性表明,x%Ti-Sn O_2/Sn_3O_4不仅具有较强的还原Cr~(6+)能力,而且拥有氧化降解有机污染物甲基橙和酸性橙Ⅱ的能力。催化活性的增强归因于x%Ti-Sn O_2/Sn_3O_4具有比较大的比表面积和更强的光吸收,同时Sn O_2/Sn_3O_4异质结的生成有效地提升了光生电子与空穴的分离效率。     

Er~(3+)-Yb~(3+)掺杂SiO_2-SrO-NaF玻璃陶瓷的制备及表征

采用熔融晶化法制备了主晶相为SrF_2的Er~(3+)-Yb~(3+)共掺透明氟氧化物玻璃陶瓷,利用DSC、XRD、SEM、UV-Vis-NIR和荧光光谱对样品的结构、形貌、发光性能进行了测试与表征。研究表明:该体系玻璃最佳热处理温度为620℃,最佳热处理时间为2h,并讨论了Yb~(3+)不同掺杂浓度对Er~(3+)-Yb~(3+)共掺玻璃陶瓷样品上转换发光性能的影响,确定Er~(3+)-Yb~(3+)最佳掺杂浓度比为1∶7,同时观察到了明亮的绿光(522,540 nm)和较弱的红光(656 nm),对Er~(3+)和Yb~(3+)之间的能量传递过程进行了讨论。     

A new solvent system for the separation of Th4+, UO 2 2+ and Zr4+ in the presence of common anions by thin-layer chromatography

Summary A TLC method has been developed for separating Th⁴⁺, UO₂ ²⁺ and Zr⁴⁺ in the presence of some common anions using a dimethylamine/acetone/formic acid mobile phase. Capacity factors, separation factors and resolution for the separation of Th⁴⁺ from UO₂ ²⁺ have been evaluated. The effect of the pH of the sample on R_F values of Th⁴⁺, UO₂ ²⁺, Ni²⁺ and Cu²⁺ has also been examined.     

Influence of the Lanthanide Ion and Solution Conditions on Formation of Lanthanide Wells–Dawson Polyoxotungstates

Lanthanide complexes of polyoxometalates, including the α₂-P₂W₁₇O₆₁ ¹⁰⁻ ligand, have been pioneered by Michael T. Pope, to whom this paper is dedicated. Examination of the solid-state and solution behavior of lanthanide complexes of the α₂-P₂W₁₇O₆₁ ¹⁰⁻ ligand are reported here to identify trends that will facilitate rational synthesis of hybrid organic lanthanide polyoxometalate complexes. Therefore, combining our data with that obtained by Pope and others a number of trends come into view. It is clear that there are two structural types for the 1:1 or 2:2 [Ln(H₂O)_X(α₂-P₂W₁₇O₆₁)]₂ ¹⁴⁻ species. The early lanthanides show a “cap to cap” structure that allows the Ln ion to be 9 coordinate and accommodates the longer bond lengths. The mid-late lanthanides show a “cap to belt” structure that allows the lanthanides to be 8 coordinate; this structural type is appropriate for the shorter bond lengths of the later lanthanides. The 1:1⇌1:2 equilibrium, that was observed by Pope for the Ce(III) analog is prevalent for the early- mid lanthanides. This equilibrium is slightly dependent on pH; however, cations have a major influence on this equilibrium. Larger, poorly hydrated cations appear to favor the 1:2 species for the early to mid lanthanides. Cations do not appear to influence the equilibrium for the later lanthanides; for all counterions, the 1:1 species was stable with no trace of the 1:2 species. Stability constants, K1 and K2, for the early to mid lanthanides were measured in this study by a competitive method and compared well with other published stability constant determinations. We suggest that the stability constants are not only dependent on the strength of interaction of the Ln with the α₂-P₂W₁₇O₆₁ ¹⁰⁻ ligand, but are also significantly influenced by the medium. The medium may bias the equilibria of the early-mid lanthanides and later lanthanides. The log K₁/log K₂ ratios are very close, suggesting that it is difficult to separate the 1:1 and 1:2 Ln: α₂-P₂W₁₇O₆₁ ¹⁰⁻ species.Electronic Supplementary Material Supplementary material for this article is available at and is accessible for authorized users.This paper is dedicated to Professor Michael T. Pope in honor of his substantial and sustained contributions to polyoxometalate chemistry and his inspiration to scientists working in the field.     

Ruthenium(II), rhodium(III) and iridium(III) based effective catalysts for hydrogenation under aerobic conditions

The new cationic mononuclear complexes [(η⁶-arene)Ru(Ph-BIAN)Cl]BF₄ [η⁶-arene = benzene (1), p-cymene (2)], [(η⁵-C₅H₅)Ru(Ph-BIAN)PPh₃]BF₄ (3) and [(η⁵-C₅Me₅)M(Ph-BIAN)Cl]BF₄ [M = Rh (4), Ir (5)] incorporating 1,2-bis(phenylimino)acenaphthene (Ph-BIAN) are reported. The complexes have been fully characterized by analytical and spectral (IR, NMR, FAB-MS, electronic and emission) studies. The molecular structure of the representative iridium complex [(η⁵-C₅Me₅)Ir(Ph-BIAN)Cl]BF₄ has been determined crystallographically. Complexes 1–5 effectively catalyze the reduction of terephthaldehyde in the presence of HCOOH/CH₃COONa in water under aerobic conditions and, among these complexes the rhodium complex [(η⁵-C₅Me₅)Rh(Ph-BIAN)Cl]BF₄ (4) displays the most effective catalytic activity.     

Quantitative determination of gas mixture composition by gas chromatography—New approach

Summary A new method has been developed for the quantitative determination of gas mixture composition where air penetration during gas sample collection would lead to erroneous results. It requires the use of a stationary phase that separates gas sample components and the air and involves 4–5 analyses of samples of equal volumes containing different amounts of air. By graphical extrapolation of the air peak area (S _air ) as a function of the peak areas of the individual components (S _comp ) the areas for these components in the absence of air can be obtained forS _air =0. Using calibration curves for the pure gas components the true quantitative composition of the gas mixture is estimated.     

MgAl2O4∶Er^3+,Yb^3+荧光粉的制备及其上转换发光性能

以尿素为沉淀剂,采用低温水热法结合煅烧过程制备出MgAl2O4∶Er^3+,Yb^3+上转换荧光粉,并对样品的结构、微观形貌及上转换发光性能予以表征。结果表明,随尿素加入量的增大,产物主形貌由六角片状结构向纳米棒状转变,经1100℃煅烧可得纯相镁铝尖晶石结构,且Er^3+和Yb^3+能有效进入MgAl2O4晶格并占据Mg^2+位置形成均匀固溶体。在980 nm光激发下,MgAl2O4∶1.0%(n/n)Er^3+,x%(n/n)Yb^3+(x=0~8.0)荧光粉表现出在524、545 nm处绿光以及658 nm处的强红光发射,红绿光强度均在5.0%(n/n)Yb^3+掺杂时达到最大,但红绿光强度比却在7.0%(n/n)Yb^3+掺杂时达到最大值5.2,这归因于Er^3+-Er^3+之间交叉弛豫(CR)在红光发射过程中所起的重要作用。通过控制荧光粉中Yb^3+的掺杂量,能初步实现对于黄绿光色度的有效调控。     

Dy3+/Tb3+双掺含SrWO4晶相玻璃陶瓷的合成与能量传递

采用熔融晶化法成功制备了Dy~(3+)/Tb~(3+)双掺含SrWO4晶相玻璃陶瓷,并对其光学性能进行研究。利用差示扫描量热分析仪(DSC)确定了热处理温度,利用X射线衍射(XRD)确定了玻璃基质中有SrWO_4晶粒析出,并结合透过率曲线确定最佳析晶温度和时间为710℃保温1.5 h。探讨了当Dy_2O_3的浓度为0.8%(n/n)时,Tb_4O_7浓度对玻璃陶瓷样品发光性能的影响,在Dy~(3+)/Tb~(3+)双掺玻璃陶瓷的发射光谱中表明:在350 nm激发下,544 nm处存在明显的发射峰。随着Tb_4O_7浓度增加,能量传递效率逐渐增加。当Tb_4O_7浓度达到1.9%(n/n)时,绿光发射强度达到最大值。结合Dexter能量传递理论和荧光衰减曲线,确定了Dy~(3+)到Tb~(3+)存在能量传递。     

Apparent molar heat capacity and relative enthalpy of aqueous NaOH between 323 and 523K

The apparent molar heat capacity, C _p,, of aqueous NaOH has been measured at temperatures between 50 and 250°C and molalities from 0.05 to 1.5 mol-kg^–1. Enthalpies of dilution L were also determined at 99°C and apparent molar relative enthalpies L were calculated up to 1.9 m. Measurements were performed by means of a flow calorimetric apparatus constructed in our laboratory and standardized for C _p, and L with aqueous Na₂SO₄ and with the formation of water from its ions, respectively. Characteristics and performance of this calorimeter are described in detail. Pitzer's semiempirical equations are used for the representation of the results and a general fitting of C _p, data is reported using also recent literature values measured between 4 and 55°C. The fitted parameters are finally utilized, through an integration procedure, to derive a general equation to calculate L at any temperature between 4 and 250°C.     

La_7O_6(BO_3)(PO_4)_2∶Eu~(3+)/Tb~(3+)荧光材料的制备及其光致发光性能

采用优化的高温固相方法制备了稀土离子Eu~(3+)和Tb~(3+)掺杂的La_7O_6(BO_3)(PO_4)_2系荧光材料,并对其物相行为、晶体结构、光致发光性能和热稳定性进行了详细研究。结果表明,La_7O_6(BO_3)(PO_4)_2∶Eu~(3+)材料在紫外光激发下能够发射出红光,发射光谱中最强发射峰位于616 nm处,为5D0→7F2特征能级跃迁,Eu~(3+)的最优掺杂浓度为0.08,对应的CIE坐标为(0.610 2,0.382 3);La_7O_6(BO_3)(PO_4)_2∶Tb~(3+)材料在紫外光激发下能够发射出绿光,发射光谱中最强发射峰位于544 nm处,对应Tb~(3+)的5D4→7F5能级跃迁,Tb~(3+)离子的最优掺杂浓度为0.15,对应的CIE坐标为(0.317 7,0.535 2)。此外,对2种材料的变温光谱分析发现Eu~(3+)和Tb~(3+)掺杂的La_7O_6(BO_3)(PO_4)_2荧光材料均具有良好的热稳定性。     

Local structure and photoluminescent characteristics of Eu<Superscript>3+</Superscript> in ZnO–SiO<Subscript>2</Subscript> glasses

The photoluminescence properties of xZnO–(100−x)SiO₂ (x = 0, 5, 10, 20) containing 1% Eu₂O₃ prepared by a sol–gel method were systematically investigated. The results indicated that the relative proportion of f–f transitions to charge transfer (CT) absorption decreased with the increase of ZnO concentration. The intensity of ⁵D₀–⁷F_J transitions of Eu³⁺ ions was enhanced with the increase of ZnO content due to local structure changes and decreased quantities of Eu³⁺ ions clusters. The results of fluorescence line narrow (FLN) spectra indicated that Eu³⁺ ions occupied one site in SiO₂ glass and two sites in ZnO–SiO₂ glasses. The second-order crystal field parameters were calculated. B₂₀ and B₂₂ for site 1 increased with excitation energy, while ones hardly changed for site 2.