Effect of titanium dioxide nanoparticles on polymer network formation

This work presents a study of the effect of nanoparticles on polymer composites to develop a powerful polymer dispersed liquid crystal materials. Tri propylene glycol diarcrylate/titanium dioxide nanocomposites were produced at various titanium dioxide fractions ranging between 0 and 1?wt%, through ultraviolet curing technique during 30?min. Different technics such as polarized optical microscopy, Fourier transform infrared spectroscopy, differential scanning calorimetry, and thermal gravimetric analysis were used to characterize the samples. A dynamic swelling of polymer network was also investigated. The evolution of the acrylic double-bond conversion shows a decrease in the absorption intensity at 1637?cm^?1. It is noted that the conversion rate decreases from 0.1 to 1?wt% of titanium dioxide nanoparticles. An increase in glass transition temperature is observed by differential scanning calorimetry. The thermogravimetric analysis results reveal a highly improved thermal stability upon the addition of the reinforcing phase. The follow of kinetics swelling of polymer network shows a decrease of the swell ratio with the inclusion of titanium dioxide nanoparticles.     

Compositional and structural evolution of the titanium dioxide formation by thermal oxidation

Titanium oxide films were prepared by annealing DC magnetron sputtered titanium films in an oxygen ambient. X-ray diffraction （XRD）, Auger electron spectroscopy （AES） sputter profiling, MCs^＋-mode secondary ion mass spectrometry （MCs^＋-SIMS） and atomic force microscopy （AFM） were employed, respectively, for the structural, com- positional and morphological characterization of the obtained films. For temperatures below 875 K, titanium films could not be fully oxidized within one hour. Above that temperature, the completely oxidized films were found to be rutile in structure. Detailed studies on the oxidation process at 925K were carried out for the understanding of the underlying mechanism of titanium dioxide （TiO2） formation by thermal oxidation. It was demonstrated that the formation of crystalline TiO2 could be divided into a short oxidation stage, followed by crystal forming stage. Relevance of this recognition was further discussed.     

Utilization of saffron (<Emphasis Type="Italic">Crocus sativus L.</Emphasis>) as sensitizer in dye-sensitized solar cells (DSSCs)

Photoelectrodes of dye-sensitized solar cells (DSSCs) have been prepared using nanosized titanium dioxide that have soaked in a solution of different saffron (Crocus sativus L.) spice content in ethanol. The optimized polyacrylonitrile (PAN)-based gel polymer electrolyte with 40.93 wt.% ethylene carbonate, 37.97 wt.% propylene carbonate, 4.37 wt.% tetrapropylammonium iodide, 9.86 wt.% PAN, 1.24 wt.% 1-butyl-3-methylimidazolium iodide, 4.35 wt.% lithium iodide and 1.28 wt.% iodine has been used as the electrolyte for DSSC. The electrolyte has conductivity of 2.91 mS cm^?1 at room temperature (298 K). DSSCs were also sensitized with saffron solution that has been added with 30 wt.% chenodeoxycholic acid (CDCA) co-adsorbent and designated as DSSC P4. The solar cell converts light-to-electricity at an efficiency of 0.31%. This is 29% enhancement in efficiency for the DSSC without addition of CDCA in the saffron-ethanol solution. The DSSC exhibits current density at short-circuit (J _sc ) of 1.26 mA cm^?2, voltage at open circuit (V _oc ) of 0.48 V and 51% fill factor. DSSC P4 also exhibits the highest incident photon-to-current density of more than 40% at 340 nm wavelength.     

Annealing effect on ion-beam-sputtered titanium dioxide film

We found that the extinction coefficient of ion-beam-sputtered titanium dioxide films first decreased with increasing annealing temperature then increased drastically when annealing temperature was increased above ~200 degrees C for 24 h of annealing time. The decreasing extinction coefficient with annealing temperature was attributed to a reduction in absorption owing to oxidation of the film by annealing. The film structure remained amorphous to 200 degrees C annealing temperature. The drastic increase of extinction coefficients above ~200 degrees C was associated with the appearance of an anatase polycrystalline structure and was attributed to scattering by the polycrystalline structure. With shorter annealing time the transition temperature from amorphous to polycrystalline anatase was higher. Guidance for reducing the optical loss of laser mirrors is proposed.     

Use of successive ionic layer adsorption and reaction (SILAR) method for amorphous titanium dioxide thin films growth

Use of successive ionic layer adsorption and reaction (SILAR) method was preferred for the growth of amorphous titanium dioxide (TiO₂) thin films at ambient temperature. Further, these films were annealed at 673 K for 2 h in air for structural improvement and characterized for structural, surface morphological, optical and electrical properties. An amorphous structure of TiO₂ was retained even after annealing as confirmed from XRD studies. The spherical grains of relatively large size were compressed after annealing. A red shift in band gap energy and decrease in electrical resistivity were observed due to annealing treatment.     

金-二氧化钛（Au-TiO_2）复合薄膜的制备及局域表面等离子体共振（LSPR）效应

利用溶胶凝胶法在玻璃衬底上制备了金-二氧化钛（Au-TiO2）复合纳米薄膜,研究了热处理温度对复合薄膜表面纳米颗粒沉积的影响。利用原子力显微镜对样品进行了形貌表征,结果显示：复合薄膜是由纳米微晶组成的致密膜,温度越高越有利于Au粒子的形成。在550℃的热处理温度下,薄膜表面沉积的纳米微晶的粒径约为100nm。利用紫外-可见分光光度计测量了反射谱线,结果表明：由于局域表面等离子体共振（LSPR）的产生,在不同的热处理温度下,第一个反射峰（短波长处）不发生变化,第二个反射峰（长波长处）发生漂移（红移）。     

Thermal Stability of the Structure and Optical Properties of Nanostructured TIO2 Films

Russian Physics Journal - The structure and optical properties of titanium dioxide films have been studied during annealing from 100 to 400°C. The films were obtained by ion-plasma...     

Polymer electrolyte for photoelectrochemical cell and dye-sensitized solar cell: a brief review

This paper reviews the use of solid polymeric electrolyte (SPE) and gel polymeric electrolyte (GPE) in photoelectrochemical cell (PEC) and dye-sensitized solar cell (DSSC). The structure of PEC and its working principle are presented. The various types of polymer electrolytes utilized in PEC and DSSC have been highlighted in this review. It also highlights the comparison of performance of PEC and DSSC utilizing those polymer electrolytes. This review is completed with the list of other SPEs that potentially be tested in DSSC.     

Conductivity studies of poly(ethylene oxide)(PEO)/poly(vinyl alcohol) (PVA) blend gel polymer electrolytes for dye-sensitized solar cells

Poly(ethylene oxide)(PEO)–poly(vinyl alcohol) (PVA) blend-based gel polymer electrolytes (GPEs) have been prepared by blending equal weights of PEO and PVA in ethylene carbonate (EC), dimethyl sulfoxide (DMSO), tetrabutylammonium iodide (TBAI), and iodine crystals (I₂). The conductivity, diffusion coefficient, number density, and ion mobility of the electrolytes have been calculated from the impedance data obtained from electrochemical impedance spectroscopy (EIS) measurements. The GPE with the composition of 7.02 wt%, PVA, 7.02 wt% PEO, 30.11 wt% ethylene carbonate (EC), 30.11 wt% DMSO, 24.08 wt% TBAI and 1.66 wt% I₂ exhibits the highest conductivity of 5.5 mS cm^?1 at room temperature. Dye-sensitized solar cells (DSSCs) with configuration fluorine tin oxide (FTO)/titanium dioxide/N3-dye/GPE/platinum/FTO have been fabricated and tested under the white light of intensity 100 mW cm^?2. The DSSC containing the highest conducting GPE exhibits the highest power conversion efficiency, η of 5.36 %.     

Steady state and time resolved laser-induced fluorescence of garlic plants treated with titanium dioxide nanoparticles

The study involves investigation of the effect of the interaction of titanium dioxide nanoparticles with garlic plant by spectroscopy techniques. For this, garlic plants have been grown in the laboratory under controlled conditions of light flux, temperature, humidity, and nutrient media. The growth and biomass parameters in terms of shoot length, fresh, and dry mass are found to increase upon the treatment of titanium dioxide nanoparticles while a reduction is observed in the root length of the garlic plants. The steady state laser-induced fluorescence, time resolved laser-induced fluorescence, and ultraviolet visible spectra of the control and titanium dioxide nanoparticles-treated plants have been acquired. The curve fitting data reveal that titanium dioxide nanoparticles decrease the intensity and fluorescence intensity ratio of red and far red chlorophyll fluorescence bands indicating increase in the photosynthetic activity and chlorophyll content. The evaluation of life time of the excited chlorophyll molecule shows that life time is effected by the treatment of the titanium dioxide nanoparticles. The results pertaining to ultraviolet visible measurement indicate increase in the concentration of chlorophyll a, chlorophyll b, total chlorophyll, carotenoid, and quercetin in the leaves of garlic plants treated with titanium dioxide nanoparticles.     

Correlation between microstructure and optical properties of nano-crystalline TiO2 thin films prepared by sol-gel dip coating

Titanium dioxide thin films have been prepared from tetrabutyl-orthotitanate solution and methanol as a solvent by sol-gel dip coating technique. TiO₂ thin films prepared using a sol-gel process have been analyzed for different annealing temperatures. Structural properties in terms of crystal structure were investigated by Raman spectroscopy. The surface morphology and composition of the films were investigated by atomic force microscopy (AFM). The optical transmittance and reflectance spectra of TiO₂ thin films deposited on silicon substrate were also determined. Spectroscopic ellipsometry study was used to determine the annealing temperature effect on the optical properties and the optical gap of the TiO₂ thin films. The results show that the TiO₂ thin films crystallize in anatase phase between 400 and 800 °C, and into the anatase-rutile phase at 1000 °C, and further into the rutile phase at 1200 °C. We have found that the films consist of titanium dioxide nano-crystals. The AFM surface morphology results indicate that the particle size increases from 5 to 41 nm by increasing the annealing temperature. The TiO₂ thin films have high transparency in the visible range. For annealing temperatures between 1000 and 1400 °C, the transmittance of the films was reduced significantly in the wavelength range of 300-800 nm due to the change of crystallite phase and composition in the films. We have demonstrated as well the decrease of the optical band gap with the increase of the annealing temperature.     

Annealing temperature effect on the properties of mercury-doped TiO2 films prepared by sol-gel dip-coating technique

This work presents the annealing temperature effect on the properties of mercury (Hg)-doped titanium dioxide (TiO₂). Thin films and polycrystalline powders have been prepared by sol-gel process. The structure, surface morphology and optical properties, as a function of the annealing temperature, have been studied by atomic force microscopy (AFM), Raman, reflectance and ellipsometric spectroscopies. In order to determine the transformation points, we have analyzed the xerogel-obtained powder by differential scanning calorimetry (DSC). Raman spectroscopy shows the crystalline anatase and rutile phases for the films annealed at 400 °C and 1000 °C respectively. The AFM surface morphology results indicate that the particle size increases from 14 to 57 nm by increasing the annealing temperature. The complex index and the optical band gap (E_g) of the films were determined by the spectroscopic ellipsometry analysis. We have found that the optical band gap decreases by increasing the annealing temperature.     

Effect of dispersing media on microstructure of electrophoretically deposited TiO2 nanoparticles in dye-sensitized solar cells

In the present study, dye-sensitized solar cells were fabricated using electrophoretically deposited layers of titanium dioxide nanoparticles from two common organic media, acetone and isopropanol. Characterization of the obtained layers by scanning electron microscope and atomic force microscope showed that a non-uniform porous layer was obtained in acetone; however, deposition from the titanium dioxide/isopropanol cell resulted in the formation of a relatively uniform microstructure. Ultraviolet-visible (UV-vis) spectra of adsorbed dye on the two layers show that more dye is loaded on the layer deposited in acetone. Current-voltage characteristics of the cells indicate that for the case of the cells made by the layer formed in acetone, the internal resistance of the cell is more than that of isopropanol medium which would decrease the efficiency of the cell. This difference was attributed to the reduction of effective surface area and also the loss of particles interconnection as a result of the presence of aggregates within the layer obtained in acetone.     

Deformation behavior,strength, and plasticity of titanium with a submicrocrystalline structure formed under warm rolling

The temperature-deformation regimes of warm rolling through profiled rolls providing production of submicrocrystalline titanium are determined. For the obtained submicrocrystalline titanium, the annealing conditions under which internal stresses decrease and plasticity increases while maintaining high-strength submicrocrystalline structure are found. The data on the microstructure, deformation behavior, elastic-plastic properties, and the type of fracture of rods with submicrocrystalline structure are reported.     

Photocatalytic Properties of Thermally Annealed Films of Titanium Butoxide

Optics and Spectroscopy - We show that titanium dioxide particles capable of reactive oxygen species generation can be produced in titanium butoxide films by annealing them at 500°C. Optimal...     

Dynamic diffusion of helium into various types of solids during their deformation and dispersion

Quantitative relations governing the penetration of helium atoms into various types of solids in the course of their plastic deformation in liquid ³He (T = 0.6–1.8 K) and ⁴He (T = 4.2 K) and dispersion in gaseous helium at 300 K were obtained and analyzed. Experiments were carried out on metals with different lattice types, ionic single crystals, amorphous alloys, and barite and titanium dioxide powders dispersed in helium. Curves illustrating helium extraction from deformed specimens under dynamic annealing were obtained. The temperature range of helium extraction was found to correlate with the melting temperature and the initial and deformed structures of a material, which determine the number and character of helium traps present in the material. The dependence of helium penetration intensity on the type of defects forming under plastic deformation for various materials, as well as the formation of chemical bonds of helium atoms to the defected structure of these materials, is discussed.     

Defect structure and thermomechanical stability of nano- and microcrystalline titanium obtained by different methods of intense plastic deformation

Mechanical stability under prolonged loading and thermostability under annealing have been studied for nano- and microcrystalline titanium obtained by different methods of intense plastic deformation. The effect of nanoporosity and the fraction of high angle boundaries formed due to intense plastic deformation has been revealed and analyzed. It has been established that, depending on the loading or the annealing temperature, thermomechanical stability of titanium can be affected, apart from the above structural characteristics, by either twin grain boundaries or titanium-carbide disperse particles.     

Adhesion studies of latex film surfaces on the meso- and nanoscale

In this paper the effects of surface roughness and annealing temperature (T) of latex coating films on adhesion are discussed for the different stages of the film formation process. The surface free energy of latex films was assessed in terms of practical work of adhesion (W) (or adherence) using a custom-built adhesion-testing device (ATD), atomic force microscopy (AFM), and contact angle measurements. For preannealed latex films surface roughness averages (R_a) were determined from AFM height images and were related to the values of W obtained from ATD measurements at room temperature. The results obtained using these tests exhibiting surface behavior on different length scales indicate a dependence of the measured adhesion on surface roughness and temperature, as well as on the length scale of the measurements.First preannealed samples were studied, which were obtained by heat treatment above the respective glass transition temperatures (T_g). Increasing the temperature of preannealing resulted in a decrease of the adherence observed in ATD experiments at room temperature. However, on the nanoscale, using AFM, no significant variation of the adherence was observed. This observation can be explained by roughness arguments. Preannealing decreases roughness which results in lower adherence values measured by ATD while for essentially single asperity AFM experiments roughness has an insignificant effect. Specimens were also annealed over a constant period of time (90 min) at different temperatures. At the end of the heat treatment, adhesion was measured at the treatment temperature by ATD. The amplified effect of temperature observed in this case on adherence is attributed to the combination of roughness decrease and increasing test temperature. In a third set of experiments completely annealed samples were studied by ATD as well as by AFM as a function of temperature. With increasing T values ATD showed a decrease in adherence, which is attributed to a decreasing surface free energy of the annealed films at elevated T values. AFM, on the other hand, showed an opposite trend which is assigned to increasing penetration of the tip into the tip/wetting polymer samples versus increasing temperature. Finally, annealing isotherms as a function of time were investigated by ATD in situ at different temperatures. This last set of experiments allowed us to optimize annealing time and temperature to achieve complete curing.     

Optimization of process parameters of titanium dioxide films by response surfaces methodology

An efficient approach for determination of the optimum process parameters for titanium dioxide coatings by using second-order response surface model is presented and investigated experimentally. Thin films were prepared by electron-beam evaporation associated with ion-beam assisted deposition by using different control factors, including starting materials, working pressure, substrate temperature, deposition rate and annealing temperature. The factorial design of the experiment was established to meet the equipment conditions and to avoid affecting the results. The main effect between various factors and interactions are independent. The significant level of both the main effects and the interaction are observed by analysis of variance (ANOVA) approach. Based on the statistical analysis, the results have provided much valuable information on the relationship between various control factors and thin film properties. Besides the optimum optical constants and surface roughness of TiO₂ thin films were obtained in the range of each parameter level. The factorial prediction model for preparation parameters of thin film was also established.     

Ti薄膜与AlN陶瓷的界面反应

用X射线衍射分析、二次离子质谱、卢瑟福背散射谱、俄歇电子能谱等表面分析技术，研究了Ti膜与AlN陶瓷衬底的界面固相反应-在高真空中用电子束蒸发的方法在抛光的200℃ AlN陶瓷衬底上淀积200nm的Ti膜，并在真空恒温炉中退火-实验表明，退火中Ti膜与AlN界面发生了扩散与反应-650℃，1h退火已观测到明显的界面反应-界面反应产物主要是钛铝化物及Ti-N化合物-铝化物是Ti-Al二元化合物和Ti-Al-N三元化合物，850℃，4h退火后则主要由Ti₂AlN组成- 关键词：