Template‐Free Synthesis of Hierarchical Vanadium‐Glycolate Hollow Microspheres and Their Conversion to V2O5 with Improved Lithium Storage Capability

Nanosheet‐assembled hierarchical V₂O₅ hollow microspheres are successfully obtained from V‐glycolate precursor hollow microspheres, which in turn are synthesized by a simple template‐free solvothermal method. The structural evolution of the V‐glycolate hollow microspheres has been studied and explained by the inside‐out Ostwald‐ripening mechanism. The surface morphologies of the hollow microspheres can be controlled by varying the mixture solution and the solvothermal reaction time. After calcination in air, hierarchical V₂O₅ hollow microspheres with a high surface area of 70 m² g^?1 can be obtained and the structure is well preserved. When evaluated as cathode materials for lithium‐ion batteries, the as‐prepared hierarchical V₂O₅ hollow spheres deliver a specific discharge capacity of 144 mA h g^?1 at a current density of 100 mA g^?1, which is very close to the theoretical capacity (147 mA h g^?1) for one Li⁺ insertion per V₂O₅. In addition, excellent rate capability and cycling stability are observed, suggesting their promising use in lithium‐ion batteries.     

Lithium Germanate (Li2GeO3): A High‐Performance Anode Material for Lithium‐Ion Batteries

A simple, cost‐effective, and easily scalable molten salt method for the preparation of Li₂GeO₃ as a new type of high‐performance anode for lithium‐ion batteries is reported. The Li₂GeO₃ exhibits a unique porous architecture consisting of micrometer‐sized clusters (secondary particles) composed of numerous nanoparticles (primary particles) and can be used directly without further carbon coating which is a common exercise for most electrode materials. The new anode displays superior cycling stability with a retained charge capacity of 725 mAh g^?1 after 300 cycles at 50 mA g^?1. The electrode also offers excellent rate capability with a capacity recovery of 810 mAh g^?1 (94 % retention) after 35 cycles of ascending steps of current in the range of 25–800 mA g^?1 and finally back to 25 mA g^?1. This work emphasizes the importance of exploring new electrode materials without carbon coating as carbon‐coated materials demonstrate several drawbacks in full devices. Therefore, this study provides a method and a new type of anode with high reversibility and long cycle stability.     

Preparation of Li4Ti5O12 Yolk–Shell Powders by Spray Pyrolysis and their Electrochemical Properties

We have reported for the first time the preparation of yolk–shell‐structured Li₄Ti₅O₁₂ powders for use as anode materials in lithium‐ion batteries. One Li₄Ti₅O₁₂ yolk–shell‐particle powder is directly formed from each droplet containing lithium, titanium, and carbon components inside the hot wall reactor maintained at 900 °C. The precursor Li₄Ti₅O₁₂ yolk–shell‐particle powders, which are directly prepared by spray pyrolysis, have initial discharge and charge capacities of 155 and 122 mA h g^?1, respectively, at a current density of 175 mA g^?1. Post‐treatment of the yolk–shell‐particle powders at temperatures of 700 and 800 °C improves the initial discharge and charge capacities. The initial discharge capacities of the Li₄Ti₅O₁₂ powders with a yolk–shell structure and a dense structure post‐treated at 800 °C are 189 and 168 mA h g^?1, respectively. After 100 cycles, the corresponding capacities are 172 and 152 mA h g^?1, respectively (retentions of 91 and 90 %).     

Lithium‐Rich Layered Oxide Li1.18Ni0.15Co0.15Mn0.52O2 as the Cathode Material for Hybrid Sodium‐Ion Batteries

Li‐rich layered oxide Li_1.18Ni_0.15Co_0.15Mn_0.52O₂ (LNCM) is, for the first time, examined as the positive electrode for hybrid sodium‐ion battery and its Na⁺ storage properties are comprehensively studied in terms of galvanostatic charge–discharge curves, cyclic voltammetry and rate capability. LNCM in the proposed sodium‐ion battery demonstrates good rate capability whose discharge capacity reaches about 90 mA h g^?1 at 10 C rate and excellent cycle stability with specific capacity of about 105 mA h g^?1 for 200 cycles at 5 C rate. Moreover, ex situ ICP‐OES suggests interesting mixed‐ions migration processes: In the initial two cycles, only Li⁺ can intercalate into the LNCM cathode, whereas both Li⁺ and Na⁺ work together as the electrochemical cycles increase. Also the structural evolution of LNCM is examined in terms of ex situ XRD pattern at the end of various charge–discharge scans. The strong insight obtained from this study could be beneficial to the design of new layered cathode materials for future rechargeable sodium‐ion batteries.     

Two‐Dimensional Cobalt‐/Nickel‐Based Oxide Nanosheets for High‐Performance Sodium and Lithium Storage

Two‐dimensional (2D) nanomaterials are one of the most promising types of candidates for energy‐storage applications due to confined thicknesses and high surface areas, which would play an essential role in enhanced reaction kinetics. Herein, a universal process that can be extended for scale up is developed to synthesise ultrathin cobalt‐/nickel‐based hydroxides and oxides. The sodium and lithium storage capabilities of Co₃O₄ nanosheets are evaluated in detail. For sodium storage, the Co₃O₄ nanosheets exhibit excellent rate capability (e.g., 179 mA h g^?1 at 7.0 A g^?1 and 150 mA h g^?1 at 10.0 A g^?1) and promising cycling performance (404 mA h g^?1 after 100 cycles at 0.1 A g^?1). Meanwhile, very impressive lithium storage performance is also achieved, which is maintained at 1029 mA h g^?1 after 100 cycles at 0.2 A g^?1. NiO and NiCo₂O₄ nanosheets are also successfully prepared through the same synthetic approach, and both deliver very encouraging lithium storage performances. In addition to rechargeable batteries, 2D cobalt‐/nickel‐based hydroxides and oxides are also anticipated to have great potential applications in supercapacitors, electrocatalysis and other energy‐storage‐/‐conversion‐related fields.     

A Core–Shell Fe/Fe2O3 Nanowire as a High‐Performance Anode Material for Lithium‐Ion Batteries

The preparation of novel one‐dimensional core–shell Fe/Fe₂O₃ nanowires as anodes for high‐performance lithium‐ion batteries (LIBs) is reported. The nanowires are prepared in a facile synthetic process in aqueous solution under ambient conditions with subsequent annealing treatment that could tune the capacity for lithium storage. When this hybrid is used as an anode material for LIBs, the outer Fe₂O₃ shell can act as an electrochemically active material to store and release lithium ions, whereas the highly conductive and inactive Fe core functions as nothing more than an efficient electrical conducting pathway and a remarkable buffer to tolerate volume changes of the electrode materials during the insertion and extraction of lithium ions. The core–shell Fe/Fe₂O₃ nanowire maintains an excellent reversible capacity of over 767 mA h g^?1 at 500 mA g^?1 after 200 cycles with a high average Coulombic efficiency of 98.6 %. Even at 2000 mA g^?1, a stable capacity as high as 538 mA h g^?1 could be obtained. The unique composition and nanostructure of this electrode material contribute to this enhanced electrochemical performance. Due to the ease of large‐scale fabrication and superior electrochemical performance, these hybrid nanowires are promising anode materials for the next generation of high‐performance LIBs.     

Uniform Decoration of Vanadium Oxide Nanocrystals on Reduced Graphene‐Oxide Balls by an Aerosol Process for Lithium‐Ion Battery Cathode Material

VO₂‐decorated reduced graphene balls were prepared by a one‐pot spray‐pyrolysis process from a colloidal spray solution of well‐dispersed graphene oxide and ammonium vanadate. The graphene–VO₂ composite powders prepared directly by spray pyrolysis had poor electrochemical properties. Therefore, the graphene–VO₂ composite powders were transformed into a reduced graphene ball (RGB)–V₂O₅ (RGB) composite by post‐treatment at 300 °C in an air atmosphere. The TEM and dot‐mapping images showed a uniform distribution of V and C components, originating from V₂O₅ and graphene, consisting the composite. The graphene content of the RGB–V₂O₅ composite, measured by thermogravimetric analysis, was approximately 5 wt %. The initial discharge and charge capacities of RGB–V₂O₅ composite were 282 and 280 mA h g^?1, respectively, and the corresponding Coulombic efficiency was approximately 100 %. On the other hand, the initial discharge and charge capacities of macroporous V₂O₅ powders were 205 and 221 mA h g^?1, respectively, and the corresponding Coulombic efficiency was approximately 93 %. The RGB–V₂O₅ composite showed a better rate performance than the macroporous V₂O₅ powders.     

Green Template‐Free Synthesis of Hierarchical Shuttle‐Shaped Mesoporous ZnFe2O4 Microrods with Enhanced Lithium Storage for Advanced Li‐Ion Batteries

In the work, a facile and green two‐step synthetic strategy was purposefully developed to efficiently fabricate hierarchical shuttle‐shaped mesoporous ZnFe₂O₄ microrods (MRs) with a high tap density of ～0.85 g cm³, which were assembled by 1D nanofiber (NF) subunits, and further utilized as a long‐life anode for advanced Li‐ion batteries. The significant role of the mixed solvent of glycerin and water in the formation of such hierarchical mesoporous MRs was systematically investigated. After 488 cycles at a large current rate of 1000 mA g^?1, the resulting ZnFe₂O₄ MRs with high loading of ～1.4 mg per electrode still preserved a reversible capacity as large as ～542 mAh g^?1. Furthermore, an initial charge capacity of ～1150 mAh g^?1 is delivered by the ZnFe₂O₄ anode at 100 mA g^?1, resulting in a high Coulombic efficiency of ～76 % for the first cycle. The superior Li‐storage properties of the as‐obtained ZnFe₂O₄ were rationally associated with its mesoprous micro‐/nanostructures and 1D nanoscaled building blocks, which accelerated the electron transportation, facilitated Li⁺ transfer rate, buffered the large volume variations during repeated discharge/charge processes, and provided rich electrode–electrolyte sur‐/interfaces for efficient lithium storage, particularly at high rates.     

Electrochemical Properties and Sodium‐Storage Mechanism of Ag2Mo2O7 as the Anode Material for Sodium‐Ion Batteries

Silver molybdate, Ag₂Mo₂O₇, has been prepared by a conventional solid‐state reaction. Its electrochemical properties as an anode material for sodium‐ion batteries (SIBs) have been comprehensively examined by means of galvanostatic charge–discharge cycling, cyclic voltammetry, and rate performance measurements. At operating voltages between 3.0 and 0.01 V, the electrode delivered a reversible capacity of nearly 190 mA h g^?1 at a current density of 20 mA g^?1 after 70 cycles. Ag₂Mo₂O₇ also demonstrated a good rate capability and long‐term cycle stability, the capacity reaching almost 100 mA h g^?1 at a current density of 500 mA g^?1, with a capacity retention of 55 % over 1000 cycles. Moreover, the sodium storage process of Ag₂Mo₂O₇ has been investigated by means of ex situ XRD, Raman spectroscopy, and HRTEM. Interestingly, the anode decomposes into Ag metal and Na₂MoO₄ during the initial discharge process, and then Na⁺ ions are considered to be inserted into/extracted from the Na₂MoO₄ lattice in the subsequent cycles governed by an intercalation/deintercalation mechanism. Ex situ HRTEM images revealed that Ag metal not only remains unchanged during the sodiation/desodiation processes, but is well dispersed throughout the amorphous matrix, thereby greatly improving the electronic conductivity of the working electrode. The “in situ” decomposition behavior of Ag₂Mo₂O₇ is distinct from that of chemically synthesized, metal‐nanoparticle‐coated electrode materials, and provides strong supplementary insight into the mechanism of such new anode materials for SIBs and may set a precedent for the design of further materials.     

Porous Carbon Anodes for a High Capacity Lithium‐Ion Battery Obtained by Incorporating Silica into Benzoxazine During Polymerization

Porous carbon anodes with a controllable V_mes/V_mic ratio were synthesized through the self‐assembly of poly(benzoxazine‐co‐resol) and the simultaneous hydrolysis of tetraethyl orthosilicate (TEOS) followed by carbonization and removal of silica. The V_mes/V_mic ratio of the carbon can be controlled in the range of approximately 1.3–32.6 through tuning the amount of TEOS. For lithium‐ion battery anodes, a correlation between the electrochemical performance and V_mes/V_mic ratio has been established. A high V_mes/V_mic ratio in porous carbons is favorable for enhancing the accessibility of Li ions to active sites provided by the micropores and for achieving good lithium storage performance. The obtained porous carbon exhibits a high reversible capacity of 660 mAh g^?1 after 70 cycles at a current density of 100 mA g^?1. Moreover, at a high current density of 3000 mA g^?1, the capacity still remains at 215 mAh g^?1, showing a fast charge‐discharge potential. This synthesis method relying on modified benzoxazine chemistry with the hydrolysis of TEOS may provide a new route for the development of mesoporous carbon‐based electrode materials.     

A Facile Molten‐Salt Route for Large‐Scale Synthesis of NiFe2O4 Nanoplates with Enhanced Lithium Storage Capability

Binary metal oxides have been deemed as a promising class of electrode materials for high‐performance lithium ion batteries owing to their higher conductivity and electrochemical activity than corresponding monometal oxides. Here, NiFe₂O₄ nanoplates consisting of nanosized building blocks have been successfully fabricated by a facile, large‐scale NaCl and KCl molten‐salt route, and the changes in the morphology of NiFe₂O₄ as a function of the molten‐salt amount have been systemically investigated. The results indicate that the molten‐salt amount mainly influences the diameter and thickness of the NiFe₂O₄ nanoplates as well as the morphology of the nanosized building blocks. Cyclic voltammetry (CV) and galvanostatic charge–discharge measurements have been conducted to evaluate the lithium storage properties of the NiFe₂O₄ nanoplates prepared with a Ni(NO₃)₂/Fe(NO₃)₃/KCl/NaCl molar ratio of 1:2:20:60. A high reversible capacity of 888 mAh g^?1 is delivered over 100 cycles at a current density of 100 mA g^?1. Even at a current density of 5000 mA g^?1, the discharge capacity could still reach 173 mAh g^?1. Such excellent electrochemical performances of the NiFe₂O₄ nanoplates are contributed to the short Li⁺ diffusion distance of the nanosized building blocks and the synergetic effect of the Ni²⁺ and Fe³⁺ ions.     

Li2C2, a High‐Capacity Cathode Material for Lithium Ion Batteries

As a typical alkaline earth metal carbide, lithium carbide (Li₂C₂) has the highest theoretical specific capacity (1400 mA h g^?1) among all the reported lithium‐containing cathode materials for lithium ion batteries. Herein, the feasibility of using Li₂C₂ as a cathode material was studied. The results show that at least half of the lithium can be extracted from Li₂C₂ and the reversible specific capacity reaches 700 mA h g^?1. The C?C bond tends to rotate to form C4 (C?C???C?C) chains during lithium extraction, as indicated with the first‐principles molecular dynamics (FPMD) simulation. The low electronic and ionic conductivity are believed to be responsible for the potential gap between charge and discharge, as is supported with density functional theory (DFT) calculations and Arrhenius fitting results. These findings illustrate the feasibility to use the alkali and alkaline earth metal carbides as high‐capacity electrode materials for secondary batteries.     

Pyrene‐Anderson‐Modified CNTs as Anode Materials for Lithium‐Ion Batteries

An organo‐functionalized polyoxometalate (POM)–pyrene hybrid (Py‐Anderson) has been used for noncovalent functionalization of carbon nanotubes (CNTs) to give a Py‐Anderson‐CNT nanocomposite through π–π interactions. The as‐synthesized nanocomposite was used as the anode material for lithium‐ion batteries, and shows higher discharge capacities and better rate capacity and cycling stability than the individual components. When the current density was 0.5 mA cm^?2, the nanocomposite exhibited an initial discharge capacity of 1898.5 mA h g^?1 and a high discharge capacity of 665.3 mA h g^?1 for up to 100 cycles. AC impedance spectroscopy provides insight into the electrochemical properties and the charge‐transfer mechanism of the Py‐Anderson‐CNTs electrode.     

Mesoporous MnCo2O4 with a Flake‐Like Structure as Advanced Electrode Materials for Lithium‐Ion Batteries and Supercapacitors

A mesoporous flake‐like manganese‐cobalt composite oxide (MnCo₂O₄) is synthesized successfully through the hydrothermal method. The crystalline phase and morphology of the materials are characterized by X‐ray diffraction, field‐emission scanning electron microscopy, transmission electron microscopy, and Brunauer–Emmett–Teller methods. The flake‐like MnCo₂O₄ is evaluated as the anode material for lithium‐ion batteries. Owing to its mesoporous nature, it exhibits a high reversible capacity of 1066 mA h g^?1, good rate capability, and superior cycling stability. As an electrode material for supercapacitors, the flake‐like MnCo₂O₄ also demonstrates a high supercapacitance of 1487 F g^?1 at a current density of 1 A g^?1, and an exceptional cycling performance over 2000 charge/discharge cycles.     

CNT@Fe3O4@C Coaxial Nanocables: One‐Pot,Additive‐Free Synthesis and Remarkable Lithium Storage Behavior

By using carbon nanotubes (CNTs) as a shape template and glucose as a carbon precursor and structure‐directing agent, CNT@Fe₃O₄@C porous core/sheath coaxial nanocables have been synthesized by a simple one‐pot hydrothermal process. Neither a surfactant/ligand nor a CNT pretreatment is needed in the synthetic process. A possible growth mechanism governing the formation of this nanostructure is discussed. When used as an anode material of lithium‐ion batteries, the CNT@Fe₃O₄@C nanocables show significantly enhanced cycling performance, high rate capability, and high Coulombic efficiency compared with pure Fe₂O₃ particles and Fe₃O₄/CNT composites. The CNT@Fe₃O₄@C nanocables deliver a reversible capacity of 1290 mA h g^?1 after 80 cycles at a current density of 200 mA g^?1, and maintain a reversible capacity of 690 mA h g^?1 after 200 cycles at a current density of 2000 mA g^?1. The improved lithium storage behavior can be attributed to the synergistic effect of the high electronic conductivity support and the inner CNT/outer carbon buffering matrix.     

Core–Shell α‐Fe2O3@α‐MoO3 Nanorods as Lithium‐Ion Battery Anodes with Extremely High Capacity and Cyclability

α‐Fe₂O₃ nanoparticles are uniformly coated on the surface of α‐MoO₃ nanorods through a two‐step hydrothermal synthesis method. As the anode of a lithium‐ion battery, α‐Fe₂O₃@α‐MoO₃ core–shell nanorods exhibit extremely high lithium‐storage performance. At a rate of 0.1 C (10 h per half cycle), the reversible capacity of α‐Fe₂O₃@α‐MoO₃ core–shell nanorods is 1481 mA h g^?1 and a value of 1281 mA h g^?1 is retained after 50 cycles, which is much higher than that retained by bare α‐MoO₃ and α‐Fe₂O₃ and higher than traditional theoretical results. Such a good performance can be attributed to the synergistic effect between α‐Fe₂O₃ and α‐MoO₃, the small size effect, one‐dimensional nanostructures, short paths for lithium diffusion, and interface spaces. Our results reveal that core–shell nanocomposites have potential applications as high‐performance lithium‐ion batteries.     

Multiple Active Sites: Lithium Storage Mechanism of Cu‐TCNQ as an Anode Material for Lithium‐Ion Batteries

Recently, carboxylate metal‐organic framework (MOF) materials were reported to perform well as anode materials for lithium‐ion batteries (LIBs); however, the presumed lithium storage mechanism of MOFs is controversial. To gain insight into the mechanism of MOFs as anode materials for LIBs, a self‐supported Cu‐TCNQ (TCNQ: 7,7,8,8‐tetracyanoquinodimethane) film was fabricated via an in situ redox routine, and directly used as electrode for LIBs. The first discharge and charge specific capacities of the self‐supported Cu‐TCNQ electrode are 373.4 and 219.4 mAh g^?1, respectively. After 500 cycles, the reversible specific capacity of Cu‐TCNQ reaches 280.9 mAh g^?1 at a current density of 100 mA g^?1. Mutually validated data reveal that the high capacity is ascribed to the multiple‐electron redox conversion of both metal ions and ligands, as well as the reversible insertion and desertion of Li⁺ ions into the benzene rings of ligands. This work raises the expectation for MOFs as electrode materials of LIBs by utilizing multiple active sites and provides new clues for designing improved electrode materials for LIBs.     

Sulfur‐Impregnated Core–Shell Hierarchical Porous Carbon for Lithium–Sulfur Batteries

Core–shell hierarchical porous carbon spheres (HPCs) were synthesized by a facile hydrothermal method and used as host to incorporate sulfur. The microstructure, morphology, and specific surface areas of the resultant samples have been systematically characterized. The results indicate that most of sulfur is well dispersed over the core area of HPCs after the impregnation of sulfur. Meanwhile, the shell of HPCs with void pores is serving as a retard against the dissolution of lithium polysulfides. This structure can enhance the transport of electron and lithium ions as well as alleviate the stress caused by volume change during the charge–discharge process. The as‐prepared HPC‐sulfur (HPC‐S) composite with 65.3 wt % sulfur delivers a high specific capacity of 1397.9 mA h g^?1 at a current density of 335 mA g^?1 (0.2 C) as a cathode material for lithium–sulfur (Li‐S) batteries, and the discharge capacity of the electrode could still reach 753.2 mA h g^?1 at 6700 mA g^?1 (4 C). Moreover, the composite electrode exhibited an excellent cycling capacity of 830.5 mA h g^?1 after 200 cycles.     

High‐Loading Nano‐SnO2 Encapsulated in situ in Three‐Dimensional Rigid Porous Carbon for Superior Lithium‐Ion Batteries

Tin oxide nanoparticles (SnO₂ NPs) have been encapsulated in situ in a three‐dimensional ordered space structure. Within this composite, ordered mesoporous carbon (OMC) acts as a carbon framework showing a desirable ordered mesoporous structure with an average pore size (≈6 nm) and a high surface area (470.3 m² g^?1), and the SnO₂ NPs (≈10 nm) are highly loaded (up to 80 wt %) and homogeneously distributed within the OMC matrix. As an anode material for lithium‐ion batteries, a SnO₂@OMC composite material can deliver an initial charge capacity of 943 mAh g^?1 and retain 68.9 % of the initial capacity after 50 cycles at a current density of 50 mA g^?1, even exhibit a capacity of 503 mA h g^?1 after 100 cycles at 160 mA g^?1. In situ encapsulation of the SnO₂ NPs within an OMC framework contributes to a higher capacity and a better cycling stability and rate capability in comparison with bare OMC and OMC ex situ loaded with SnO₂ particles (SnO₂/OMC). The significantly improved electrochemical performance of the SnO₂@OMC composite can be attributed to the multifunctional OMC matrix, which can facilitate electrolyte infiltration, accelerate charge transfer, and lithium‐ion diffusion, and act as a favorable buffer to release reaction strains for lithiation/delithiation of the SnO₂ NPs.     

Mesoporous Spherical Li4Ti5O12 as High‐Performance Anodes for Lithium‐Ion Batteries

Porous microspherical Li₄Ti₅O₁₂ aggregates (LTO‐PSA) can be successfully prepared by using porous spherical TiO₂ as a titanium source and lithium acetate as a lithium source followed by calcinations. The synthesized LTO‐PSA possess outstanding morphology, with nanosized, porous, and spherical distributions, that allow good electrochemical performances, including high reversible capacity, good cycling stability, and impressive rate capacity, to be achieved. The specific capacity of the LTO‐PSA at 30 C is as high as 141 mA h g^?1, whereas that of normal Li₄Ti₅O₁₂ powders prepared by a sol–gel method can only achieve 100 mA h g^?1. This improved rate performance can be ascribed to small Li₄Ti₅O₁₂ nanocrystallites, a three‐dimensional mesoporous structure, and enhanced ionic conductivity.