三维编织复合材料渐进损伤的非线性数值分析

基于考虑纤维束相互挤压的八边形纤维束截面单胞模型,引入周期性位移边界条件,采用 细观非线性有限元方法,建立了三维四向编织复合材料的渐进损伤拉伸强度模型. 该模型考 虑了增强体纤维束纵向非线性剪切应力-应变关系,采用Hashin型损伤失效准则定义了纤维 束的典型损伤类型,并根据纤维束和纯基体相应损伤类型所造成的材料性能退化,模拟了不 同编织角试件各类损伤产生、扩展及材料最终破坏的整个过程. 模型数值结果与实验数据吻 合较好,证明了该模型的合理有效性. 探讨了组分材料剪切非线性、损伤对材料宏观非线性 本构行为的影响,结果表明：随着编织角增大,纤维束剪切非线性效应和累积损伤对材料非 线性力学行为的影响明显增强.     

三维五向编织复合材料渐进损伤分析及强度预测

基于五向编织复合材料连续体细观结构单胞,提出了材料的三维渐进损伤分析模型,采用非线性有限元方法并结合均匀化平均思想,建立了三维五向编织复合材料的强度预测胞元模型.经研究典型编织角材料在拉伸载荷作用下细观损伤的发生及演化过程,分析了材料的细观失效机理,获得了材料的宏观拉伸应力应变曲线和极限破坏强度,并详细探讨了工艺参数编织角对材料宏观力学性能的影响规律.     

纤维缠绕复合材料压力容器渐进损伤分析

利用大型有限元软件ANSYS的参数化设计语言(APDL)建立了纤维缠绕复合材料压力容器的有限元模型,该模型真实地反应了复合材料压力容器封头处纤维缠绕层的厚度以及纤维缠绕角度沿子午线不断变化的情况,即充分体现该压力容器结构的真实性.针对建立的有限元模型,对复合材料压力容器在一定内压下的应变进行了分析,将分析的结果与试验结果比较,验证该模型的准确性.在此基础上进行了复合材料压力容器的渐进损伤分析,获得了复合材料压力容器在外载荷逐渐增加的情况下,复合材料缠绕层逐层失效破坏的详细信息,为复合材料压力容器的设计提供一定的依据.     

基于多尺度方法的三维编织C/C复合材料弯曲失效特性分析

为了预测三维编织C/C复合材料的弯曲失效行为,基于多尺度渐进展开理论,结合细观渐进损伤模型,建立了三维编织C/C复合材料宏细观多尺度分析模型。通过商业有限元软件ABAQUS用户子程序UMAT的二次开发,在宏观结构有限元分析中实时调用细观单胞模型进行细观渐进损伤分析,实现了宏细观尺度之间交互式信息传递和多尺度损伤模拟。利用上述模型对三点弯曲载荷下三维编织C/C复合材料梁的渐进损伤和失效过程进行了模拟,预测了梁的载荷-挠度曲线和弯曲强度,并与实验结果进行了对比分析,验证了基于多尺度方法的三维编织C/C复合材料弯曲强度预测模型的有效性,为此类材料及结构失效分析提供了一种手段。     

三维编织复合材料剪切性能分析

根据三维四向编织复合材料的结构特点，提出了刚度合成法预测编织复合材料剪切弹性模量，比较了整体编织试件和裁剪所得试件理论剪切性能差别，分析了三维编织T300／QY9512复合材料的剪切性能随试件沿宽度和厚度两个方向内部单胞数目的变化规律。结果表明，三维编织复合材料剪切弹性模量是与试件尺寸相关的，只有当试件尺寸较大、沿宽度和厚度两个方向内部单胞数目较多时，试件尺寸的影响可以忽略。当沿宽度方向单胞数目较大时，整体编织试件和裁剪所得试件的剪切模量相近。本文还得到了在复合材料板的纤维体积含量不变的情况下，剪切模量随编织角的变化规律。     

三维编织复合材料弯曲性能分析

根据三维四向编织复合材料的结构特点,提出了用刚度合成法来预测复合材料的弯曲模量,并对三维编织T300/QY9512复合材料的弯曲模量进行了预测.分析结果表明,由于试件的表面单胞和内部单胞的结构不同,得到试件的弯曲模量略高于拉伸模量,该结果与试验值相符.另外,当试件尺寸较大、内部单胞数较多时,可以不考虑表面单胞和内部单胞性能差异的影响,而认为三维编织复合材料的弯曲模量只与内部单胞的性能有关,这对工程分析和试件制作具有指导意义.     

三维编织复合材料几何建模及数值分析

论文根据三维编织复合材料的结构特点,把整体结构分为内部单胞、表面单胞和角单胞三种类型的子单胞,考虑空间纤维束的相互扭结和挤压所造成的纤维束的弯曲和截面变形,针对每种类型的子单胞,建立了相应的几何分析模型.引入周期性位移边界条件,建立了材料的弹性性能预报模型,得到了三维编织复合材料的工程弹性常数.通过数值比较可以看出,论文所给出的数值计算结果与实验结果吻合较好,从而验证了本文模型的有效性.     

复合材料层合板面内渐进损伤分析的CDM模型

基于连续介质损伤力学,提出了一个预测复合材料层合板面内渐进损伤分析的模型,它包括损伤表征、损伤判定和损伤演化3 部分. 模型能够区分纤维拉伸断裂、纤维压缩断裂、纤维间拉伸损伤和纤维间压缩损伤4 种损伤模式,定义了与4 个损伤模式对应的损伤状态变量,导出了材料主轴系下损伤前后材料本构之间的关系. 损伤起始采用Puck 准则判定,损伤演化由特征长度内应变能释放密度控制. 假定材料服从线性应变软化行为,建立了损伤状态变量关于断裂面上等效应变的渐进损伤演化法则. 模型涵盖了复合材料面内损伤起始、演化直至最终失效的全过程. 完成了含孔[45/0/-45/90]_2S 层合板在拉伸和压缩载荷下失效分析,结果表明该模型能合理进行层合板的强度预测和损伤失效分析.      

复合材料层合板低速冲击响应和损伤分析

通过在有限元软件Abaqus/Explicit中编写用户材料子程序VUMAT,建立了一种基于能量演化的复合材料低速冲击渐进损伤模型．该模型以三维Hashin准则来预测层内损伤的起始,以一种简化的损伤变量来模拟层内损伤的演化,将具有双线性牵引-分离本构的零厚度界面单元插入层间来模拟分层损伤．采用该模型对14.7 J冲击能量下的纤维增强复合材料低速冲击过程进行了仿真分析,计算得到的冲击力-时间曲线、能量-时间曲线和损伤分布与试验结果吻合较好．根据数值模拟结果,分析了纤维、基体和分层损伤的扩展规律,为低速冲击下的复合材料结构设计提供了理论依据．     

基于渐进均匀化的平纹编织复合材料低速冲击多尺度方法

针对平纹编织复合材料低速冲击响应和损伤问题,提出了一种多尺度分析方法. 首先, 建立微观尺度单胞模型,引入周期性边界条件,采用最大主应力失效准则和直接刚度退化模型表征纤维丝和基体的损伤起始与演化,预测了纤维束的弹性性能和强度性能. 其次,将这些性能参数代入介观尺度单胞模型,基于Hashin和Hou的混合失效准则以及连续介质损伤模型对介观尺度单胞进行6种边界条件下的渐进损伤模拟.然后采用渐进均匀化方法,以介观尺度单胞为媒介预测了0$^\circ$和90$^\circ$子胞的性能参数,并建立平纹编织复合材料的子胞模型,进而扩展成为材料的宏观尺度低速冲击模型. 在此基础上,研究了平纹编织复合材料低速冲击下的力学响应与损伤特征.结果表明:宏观冲击仿真和试验吻合较好, 验证了多尺度方法的正确性;最大接触力、材料吸能和分层面积均随冲击能量的增大而增大,分层损伤轮廓逐渐从椭圆形向圆形转化;基体拉伸和压缩损伤的长轴方向分别与子胞材料主方向正交和一致,损伤面积前者远大于后者.      

Theoretical prediction of stiffness and strength of three-dimensional and four-directional braided composites

Based on unit cell model, the 3D 4-directional braided composites can be simplified as unidirectional composites with different local axial coordinate system and the compliance matrix of unidirectional composites can be defined utilizing the bridge model. The total stiffness matrix of braided composites can be obtained by the volume average stiffness of unidirectional composites with different local axial coordinate system and the engineering elastic constants of braided composites were computed further. Based on the iso-strain assumption and the bridge model, the stress distribution of fiber bundle and matrix of different unidirectional composites can be determined and the tensile strength of 3D 4-directional braided composites was predicted by means of the Hoffman＇s failure criterion for the fiber bundle and Mises＇ failure criterion for the matrix.     

含孔复合材料层合板静拉伸三维逐渐损伤分析

针对面内静拉伸纤维增强复合材料含中孔层合板，发展了参数化三维逐渐损伤模型. 该模型 可以模拟含中孔层合板损伤起始、发展及最终结构破坏整个过程，并能较好地预测含中孔层 合板的破坏模式和破坏强度. 采用所发展的模型和有限元三维逐渐损伤分析技术即应力分 析、失效判定准则及损伤过程中材料性能退化等，对其他文献所提供的9种不同类型含中孔层合板进行了损伤扩展分析及强度预测，同时对层合板的损伤基本机理、类型及其相互关联作用进行了探讨，计算结果与文献实验结果非常吻合.     

复合材料损伤容限分析软件CDTAC 1．0版简介

本文简要地介绍了由飞机强度研究所研制的复合材料损伤容限分析软件CDTAC1．0版本的各项基本功能,及其所用的基本理论和程序结构,并给出典型算例。     

三维编织复合材料模量的双尺度有限元计算

针对三维编织复合材料的力学性能进行了双尺度有限元(TSA)数值计算,给出了计算模型和算法过程,并将数值结果与文献中的实验数据进行了比较,验证了算法的物理准确性。编织复合材料的力学性能不仅依赖于材料的基本组份,也与细观构造相关。双尺度有限元计算可以数值模拟出三维编织复合材料的整体力学性能,从而为材料的研发提供指导。本文的双尺度有限元三维数值计算方法可以推广到其他增强／孔隙等多相复合材料的数值模拟。     

纤维复合材料损伤过程的数值模拟

利用界面断裂力学和有限元法数值模拟纤维增强复合材料的细观损伤过程，研究各种主要破坏模式之间的相互转变和影响，指出以断裂能和混合度表示的界面性能是控制复合材料损伤过程的主要细观参数。分析了界面韧度对破坏性能的影响，探讨了基于破坏模式控制的复合材料韧度设计的新途径。     

A continuum damage model for delaminations in laminated composites

Delamination, a typical mode of interfacial damage in laminated composites, has been considered in the context of continuum damage mechanics in this paper. Interfaces where delaminations could occur are introduced between the constituent layers. A simple but appropriate continuum damage representation is proposed. A single scalar damage parameter is employed and the degradation of the interface stiffness is established. Use has been made of the concept of a damage surface to derive the damage evolution law. The damage surface is constructed so that it combines the conventional stress-based and fracture-mechanics-based failure criteria which take account of mode interaction in mixed-mode delamination problems. The damage surface shrinks as damage develops and leads to a softening interfacial constitutive law. By adjusting the shrinkage rate of the damage surface, various interfacial constitutive laws found in the literature can be reproduced. An incremental interfacial constitutive law is also derived for use in damage analysis of laminated composites, which is a non-linear problem in nature. Numerical predictions for problems involving a DCB specimen under pure mode I delamination and mixed-mode delamination in a split beam are in good agreement with available experimental data or analytical solutions. The model has also been applied to the prediction of the failure strength of overlap ply-blocking specimens. The results have been compared with available experimental and alternative theoretical ones and discussed fully.     

Nonlinear progressive damage model for composite laminates used for low-velocity impact

In order to effectively describe the progressively intralaminar and interlam- inar damage for composite laminates, a three dimensional progressive damage model for composite laminates to be used for low-velocity impact is presented. Being applied to three-dimensional （3D） solid elements and cohesive elements, the nonlinear damage model can be used to analyze the dynamic performance of composite structure and its failure be- havior. For the intralaminar damage, as a function of the energy release rate, the damage model in an exponential function can describe progressive development of the damage. For the interlaminar damage, the damage evolution is described by the framework of the continuum mechanics through cohesive elements. Coding the user subroutine VUMAT of the finite element software ABAQUS/Explicit, the model is applied to an example, i.e., carbon fiber reinforced epoxy composite laminates under low-velocity impact. It is shown that the prediction of damage and deformation agrees well with the experimental results.     

Nonlinear viscoelastic multi-scale repetitive unit cell model of 3D woven composites with damage evolution

Three-dimensional (3D) textile composites have great potential applications to aircrafts and high speed vehicles because of the high strength/weight ratios and the capabilities of manufacturing complex, net-shape preforms. This paper reports the nonlinear viscoelastic responses and damage mechanisms of one kind of 3D textile composites, named as 3D orthogonal woven composite (3DOWC) under quasi-static tensile loading based on a micro/meso-scale repetitive unit cells (RUCs) model. In the RUCs model, the resin is described with a nonlinear viscoelastic material and the fibers/tows with an elastic material. The damage initiation and propagation in resin are simulated by the post-damage constitutive models with maximum principal theory failure criteria. The fibers/tows impregnated with resin are defined by elastic transverse-isotropic material model with ultimate strengths failure of ‘expanded smeared crack’ both along and perpendicular to fibers/tows axis direction. The engineering parameters and ultimate strengths of homogenized fibers/tows filled with matrix in meso-RUCs model are transferred from the numerical analysis of the micro-RUCs. The results are compared with experimental and theoretical values of RUC deformation and damage initiation and propagation under monotonic axial loading. The methodology of establishing the nonlinear visco-elastic multi-scale model of 3D textile composites without introducing the real fabric architecture in finite element analyses is explained. With the multi-scale RUCs model, the mechanical behaviors of other kinds of 3D textile composites can also be predicted.