An approach to the Paal–Knorr pyrroles synthesis in the presence of β-cyclodextrin in aqueous media

An efficient and facile method for the synthesis of N-substituted pyrroles in moderate to good yields by the Paal–Knorr reaction of γ-diketones with amines in the presence of β-cyclodextrin in aqueous media has been developed.Moreover,this process tolerated diamines(e.g.,para-,meta- or orthophenylenediamine)to construct bis-pyrrole or mono-pyrrole derivates.β-Cyclodextrin can be recovered easily after the reactions and reused without evident loss in activity.     

Polyimide nanocomposites based on functionalized graphene sheets: Morphologies,thermal properties,and electrical and thermal conductivities

Polyimide (PI) films were prepared by reacting 4,4′-(4,4′-isopropylidene-diphenoxy)-bis(phthalic anhydride) and 1,3-bis(4-aminophenoxy)benzene. The 4-phenylbutylamine-functionalized graphene sheets (PBA-GSs) used for the preparation of the PI nanocomposite films were prepared by mixing a dispersion of graphite oxide with a solution of the ammonium salt of 4-phenylbutylamine (PBA). PI nanocomposite films containing different amounts of PBA-GS (0–10 wt%) were compared in terms of their morphologies, thermal properties, and electrical and thermal conductivities. Only a small amount of PBA-GS was required to improve the thermal properties and thermal conductivities of the PI; the maximum enhancements in these parameters were observed at 1 and 3 wt% PBA-GS, respectively. In contrast, the electrical conductivity of the PI hybrid films continued to increase with increasing PBA-GS content from 1 to 10 wt%.     

Physical properties of silicone foams filled with carbon nanotubes and functionalized graphene sheets

Free-rising silicone foams were made with loading fractions of up to 0.25 wt.-% functionalized graphene sheets (FGS) and up to 1.0 wt.-% carbon nanotubes (CNTs) using hydrogen as blowing agent. Scanning electron microscopy of the samples revealed an open cellular structure and a homogeneous dispersion of both types of nanofillers. The incorporation of nanofiller affected the foaming process and thus the final foam density and cellular structure. Transmission electron microscopy revealed the formation of a CNT network throughout the sample, while FGS presented an exfoliated and intercalated dispersion. The thermal stability of the samples was drastically affected by the presence of both nanofillers. Both nanofillers showed a positive effect on the compressive response of the foams. However, the nanocomposite foams were found to decrease the acoustic absorption with nanofiller content probably due to the variable foam structure and improved stiffness.     

β-环糊精联吡啶钌衍生物与维生素包络作用的荧光光谱分析

合成了一种新型的β-环糊精联吡啶钌衍生物[β-CD-Ru(bpy)3],采用分子荧光光谱法研究了该衍生物对一系列维生素的包络作用.β-CD-Ru(bpy)3的结构中含有发光活性基团联吡啶钌中心,因此具有良好的荧光特性.当加入与β-环糊精有主客体识别作用的维生素时,β-CD-Ru(bpy)3与维生素之间发生能量转移从而导致主体分子发生荧光猝灭.采用Benesi-Hildebrand方程,根据其猝灭值计算了该衍生物与各种维生素的包络常数.实验结果表明,维生素与β-CD-Ru(bpy)3包络作用大小顺序为维生素B12>维生素K3>维生素C>维生素A.     

Superhydrophilic functionalized graphene/fiberglass/epoxy laminates with high mechanical,impact and thermal performance and treated by plasma

This research aims to develop superhydrophilic fiberglass/epoxy nanocomposite (FGEC) laminates with high mechanical, thermal, and impact properties. In order to achieve this goal, functionalized graphene (FGA) was used as a nanofiller material to improve the mechanical, impact, and thermal behaviors of FGEC, while the plasma treatment helped to form the oxidized polar functional groups (C9O groups and C–O groups) on the fabricated FGEC laminates, thus modifying their hydrophilic behavior. The experiments were started with production of FGEC laminates by mixing FGA (0.05-0.4 wt%) with epoxy resin in presence of Acetone (to obtain better dispersion), followed by preparation of FGEC laminates using vacuum-assisted resin transfer and curing processes. Afterwards, the surfaces of the fabricated FGEC laminates were treated by air plasma at 13Pa and 30W for different treatment times in the range 5–30 min. Mechanical and impact properties of the untreated and treated laminates were investigated according to ASTM-D7025 and ISO 6603-2 standards, respectively. Also, thermal behavior of the laminates was investigated using a thermogravimetric analysis, while a high resolution camera was used to record and calculate a contact angle of the untreated and treated laminates. SEM and Optical Microscope was used to observe dispersion of FGA, microstructure, impact mechanism, and surface morphology of the fabricated FGEC matrix. Meanwhile, XPS was used to evaluate changes in the surface structures of the untreated and treated samples. The results showed that 0.35 wt% of FGA and 15-min exposure to plasma treatment were enough to improve tensile strength and impact energy of the laminates by 18% and 70%, respectively, and to decrease the water contact angle from 67° to 14°.     

Viscoelastic response and interlaminar delamination resistance of epoxy/glass fiber/functionalized graphene oxide multi-scale composites

Graphene oxide (GO) was functionalized using three different diamines, namely ethylenediamine (EDA), 4,4′-diaminodiphenyl sulfone (DDS) and p-phenylenediamine (PPD) to reinforce an epoxy/glass fiber (EP/GF) composite laminate, with the aim of improving the overall composite mechanical performance. Different mechanical characterization techniques were used to determine the mechanical performance, including: tensile stress strain, double cantilever beam (DCB) mode-I fracture toughness and dynamic mechanical thermal analysis (DMTA). Scanning electron microscopy (SEM) was used to support the results and conclusions. The results demonstrated remarkable enhancements in the mechanical performance of EP/GF composite laminates by incorporation of functionalized graphene oxide (FGO) nanofiller, whilst the mechanical performance of the GO reinforced composite only improved marginally. Finally, the mechanical performance of the EP/GF/FGO multi-scale composites was found to be dependent on the type of FGO functional groups; of which EDA exhibited the highest performance. These investigations confirmed that the EDA-FGO-reinforced EP/GF composites possess excellent potential to be used as multifunctional engineering materials in industrial applications.     

Viscoelasticity and thermal stability of polylactide composites with various functionalized carbon nanotubes

Polylactide (PLA) nanocomposites containing various functionalized multi-walled carbon nanotubes (MWCNTs) were prepared directly by melt compounding. The linear rheology and thermal stability of the PLA nanocomposites were, respectively, investigated by the parallel plate rheometer and TGA, aiming at examining the effect of surface functionalization on the dispersion of MWCNTs by using viscoelastic and thermal properties. Among three MWCNTs used in this work, the carboxylic MWCNTs present better dispersion in PLA matrix than the hydroxy and purified MWCNTs because the corresponding composite shows the lowest rheological percolation threshold, which is further confirmed by the TEM and solution experiments. The presence of all these three MWCNTs, however, nearly cannot improve the thermal stability effectively at the initial stage of degradation and the temperature corresponding to a weight loss of 5 wt% (T_5 wt%) only shows slight increase in contrast to that of the neat PLA while with increase of decomposition level, the presence of carboxylic and purified MWCNTs retards the depolymerization of PLA evidently, showing remarkable increase in the temperature corresponding to maximum rate of decomposition (T_max). Both the dispersion state and the surface functionalization of MWCNTs are very important to the thermal stability of PLA matrix.     

Structure,thermal conductivity,and thermal stability of bromobutyl rubber nanocomposites with ionic liquid modified graphene oxide

In this report, we demonstrate that both the thermal stability and the thermal conductivity of bromobutyl rubber (BIIR) nanocomposites could be improved by incorporating the ionic liquids (ILs) modified graphene oxide (GO-ILs) using a solution compounding method. The structure, thermal stability and thermal conductivity of this newly modified BIIR nanocomposites were systematically analyzed and studied. The X-ray diffraction (XRD) analysis of GO-ILs showed that ILs had been effectively intercalated into the interlayer of GO, which was found to be able to raise the exfoliation degree of GO. The increased exfoliation degree facilitated a good dispersion of GO-ILs in the BIIR matrix, as revealed by the scanning electron microscope (SEM) images. The glass transition temperatures (T_g) of the GO-ILs/BIIR nanocomposites were also raised by the addition of GO-ILs, which indicates the strong interfacial adhesion between GO-ILs and the rubber. Most importantly, the incorporation of GO-ILs in the BIIR matrix could effectively improve the thermal stability of the rubber nanocomposites according to our thermogravimetric analysis (TGA). The activation energy (E_a) of thermal decomposition of GO-ILs/BIIR nanocomposites increases with the addition of GO-ILs. Besides, the thermal conductivity of GO-ILs/BIIR nanocomposite with 4 wt% of GO-ILs had 1.3-fold improvement compared to that of unfilled BIIR.     

丁香油-β-环糊精包合物中残存态环糊精的热分解动力学

采用双外推法确定了丁香油-β-环糊精(CD)包合物中残存态β-CD最可能的热分解机制. 基于Flynn-Wall-Ozawa方法对残存态β-CD热分解反应过程的计算结果发现, 活化能(Ea)变化曲线可划分为三个阶段. 第一和第三阶段的曲线轮廓近似平行, 并且都被推定为按照Avrami-Erofe’ev A1.5模型发生热分解反应. 但是在曲线的第二阶段, 出现了一个Ea值近似相等的平台. 为此, 采用确定反应级数的方法考察了该阶段的热分解过程. 研究表明, 反应级数随着温度升高呈现规律性的降低, 表明在这个阶段残存态β-CD分解反应的复杂性. 最后, 比较了游离态β-CD和残存态β-CD在分解过程中红外光谱的变化情况. 结果显示, 它们在1000 cm-1以下的谱图轮廓存在明显差异, 这与计算给出的二者具有不同Ea值的结果是一致的.     

Enhanced thermal stability and structural characteristics of different MMT-Clay/epoxy-nanocomposite materials

Epoxy-clay nanocomposites, HDTMA-BDGE, HDTMA-BPDG, HDTMA-BBDG, HDTMA-TGDDM and HDTPP-BDGE were synthesized using hexadecylammonium clay and hexadecylphosphonium clay, respectively. The Montmorillonite (MMT) clay was modified with quaternary ammonium salt and with triphenylphosphonium salt which was intercalated into the interlayer region of MMT-Clay. The epoxy-clay systems were cured by using diaminodiphenylsulphone as a curing agent. The X-ray diffraction patterns obtained for the systems confirmed the nanodispersion of MMT-Clay in the epoxy networks. The ammonium clay-modified systems displayed appreciable mechanical and glass-transition temperature properties while, the phosphonium clay-modified system exhibited highest thermal resistance properties compared with unmodified epoxy systems. The T_g decrease observed in all the clay-modified epoxy systems, may be compromised with their advantage of requiring the filler content very low (5wt%), when compared to the conventional epoxy systems whose filler quantity is normally required from 25 to 30 wt%.     

Structures and electronic states of fluorinated graphene

Functionalized graphenes have been utilized as electronic devices and energy materials. In the present paper, the effects of fluorine-termination of graphene edge on the structures and electronic states of graphene have been investigated by means of density functional theory (DFT) method. It was found that the ionization potential (Ip) and electron affinity of graphene (EA) are blue-shifted by the F-substitution. On the other hand, the excitation energy was red-shifted. The drastic change shows a possibility as electronic devices such as field-effect transistors. The drastic change of electronic states caused by the F-substitution of graphene edge was discussed on the basis of the theoretical results.     

Enhanced thermal stability of polypyrrole hexagonal microplates fabricated by organic crystal surface-induced polymerization

The stability of polypyrrole hexagonal microplates (PHMs) fabricated by organic crystal surface-induced polymerization (OCSP) in the presence of 4-sulfobenzoic acid monopotassium salt (SBAK) crystals was examined during thermal aging at 150 °C for 10 h under air and nitrogen atmospheres. Thermal stability of PHMs and conventional polypyrroles (CPPys) was evaluated in terms of the resistivity (R_t) after aging for t h, normalized to the initial resistivity (R₀) before aging, R_t/R₀. Although the PHMs maintained R₁₀/R₀ values of 21.9 and 3.0 under air and nitrogen, respectively, the CPPys exhibited much higher R₁₀/R₀ values, of 853.8 and 14.6, respectively. A possible explanation for the enhanced thermal stability of the PHMs is the higher thermal stability and the antioxidant effect of SBAK dopant molecules. Thermo-oxidative degradation was accelerated due to direct chemical attack on the cationic pyrrole rings of atmospheric water and oxygen, leading to a steep increase in surface resistivity. The development of carbonyl defects on PPy chains during thermal aging was monitored using Fourier transform-infrared (FT-IR) spectroscopy and X-ray photoelectron spectroscopy (XPS). Ultraviolet-visible (UV-vis) spectroscopy revealed that the PHMs essentially retained the bipolaron structures, even after thermal aging for 10 h in air, whereas the CPPys showed almost no bipolaron structures.     

Triple-transforming gel prepared byβ-cyclodextrin,diphenylamine and lithium chloride in N,N-dimethylacetamide

<正>This paper describes a triple-transforming gel system(gel-sol-gel') for the first time,which is a thermo-responsive and multicomponent organogel prepared byβ-cyclodextrin(β-CD),diphenylamine(DPA) and lithium chloride(LiCl) in N,N-dimethylacetamide (DMAC) in a suitable proportion based on the supramolecular interactions.In the triple-transforming gel system,a gel(gel A) could be formed byβ-CD,DPA and LiCl in DMAC at room temperature based on stirring,then the gel could transform into a clear solution based on heating,and then the other gel(gel B) can be formed at a relatively high temperature(T_(gel),the gelation temperature by heating).The two gel states in the triple-transforming gel system have different microstructures.This gel system was characterized by OM,SEM,IR and rheology.     

The addition of functionalized graphene oxide to polyetherimide to improve its thermal conductivity and mechanical properties

The thermal and electrical conductivity and mechanical properties of polyetherimide (PEI) containing either alkyl‐aminated (enGO) or phenyl‐aminated graphene (pnGO) oxides were studied. A solution casting method was used to prepare functionalized graphene oxide/PEI composites with different filler contents. The introduction of functionalized graphene oxide to the PEI matrix improved the thermal conductivity, electrical conductivity, and mechanical properties. The thermal conductivities of the enGO 3 wt%/PEI and pnGO 3 wt%/PEI composites were 0.324 W/mK and 0.329 W/mK, respectively, due to the high thermal conductivity of the graphene‐based materials and the strong interface adhesion due to the filler surface treatment between the fillers and the matrix. The electrical conductivities of the functionalized graphene oxide/PEI composites were larger than that of PEI, but the electrical conductivity values were generally low, which is consistent with the magnitude of the insulator. The strong interfacial adhesion between the fillers and the matrix led to improved mechanical properties. Copyright © 2014 John Wiley & Sons, Ltd.     

Preparation of fluoroalkyl end-capped oligomers/magnetite nanocomposites possessing a good dispersibility and stability

Fluoroalkyl end-capped vinylphosphonic acid cooligomers-encapsulated magnetite nanocomposites were prepared by the magnetization of aqueous ferric and ferrous ions in the presence of the corresponding fluorinated cooligomers and magnetic nanoparticles under alkaline conditions. These fluorinated cooligomers magnetic composites are nanometer size-controlled very fine particles and have a good dispersibility and stability in water and traditional organic solvents. These fluorinated nanocomposites were also applied to the surface modification of poly(methyl methacrylate) to exhibit a good oleophobicity imparted by fluorine on their surface. Fluoroalkyl end-capped 2-methacryloyloxyethanesulfonic acid oligomer-encapsulated magnetite nanocomposites and fluoroalkyl end-capped 2-acrylamide-2-methylpropanesulfonic acid oligomer-encapsulated magnetite nanocomposites were prepared in good isolated yields by the magnetization of iron chlorides in the presence of the corresponding oligomers and magnetic nanoparticles under similar conditions. Colloidal stability of these fluorinated nanocomposites thus obtained in water was demonstrated to become extremely higher than that of fluorinated vinylphosphonic acid cooligomers/magnetic nanocomposites.     

功能化的石墨烯和磁铁掺杂的还原氧化石墨烯对亚甲基蓝的吸附作用

用简单可行的方法合成了功能化的石墨烯(GNSPF6)和磁铁掺杂的还原氧化石墨烯(RGO-Fe3O4),并进一步研究了pH值、接触的时间和温度对它们吸附亚甲基蓝(MB)的影响.结果表明,随着pH值和温度的增加其吸附量也随之变大,从而说明该吸附过程是自发吸热的.因为GNSPF6的吸附过程只用了不到20min的时间,所以它的吸附是高效的.用经典的准一级反应、准二级反应和粒内扩散模型对其吸附过程进行动态分析,从结果可以发现,准二级动力学模型比准一级动力学模型更适用于描述吸附过程.采用传统的Langmuir,Freundlich和L-F吸附等温线模型来模拟分析数据,在20℃时,由Langmuir吸附等温线模型模拟分析得知GNSPF6和RGO-Fe3O4对MB的最大吸附量分别为374.4和118.4mg/g.     

Confinement effects on the thermal stability of poly(ethylene oxide)/graphene nanocomposites: A reactive molecular dynamics simulation study

Nonisothermal and isothermal decomposition of poly(ethylene oxide) (PEO) loaded with different concentrations of pristine graphene (PG) and graphene oxide (GO) nanoplatelets were investigated using reactive molecular dynamics simulation. The onset of nonisothermal decomposition of the PG‐loaded PEO system was the highest among all systems, suggesting that introducing PG to the polymer improves its thermal stability (an effect that increases with an increase in the PG concentration). At low concentration, introducing GO to the polymer brings about a deterioration of the thermal stability of the polymer consistent with experimental findings. On average, the activation energy for the isothermal decomposition of PG‐loaded PEO system increases by 60% over that of the neat PEO system, while it decreases by 40% for the GO‐loaded PEO system. A time‐dependent analysis of the through‐thickness decomposition profile of the above systems reveals that the polymer confined between the PG sheets exhibit a higher thermal stability compared to the bulk polymer. However, an opposite effect is observed with the polymer confined between the GO sheets. The latter observation is attributed to accelerated polymer chain scission in confined regions due to the ejection of reactive hydroxyl radicals from the GO surface during the early stages of thermal decomposition. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2017 , 55, 1026–1035     

The comparison of thermal stability of some hydrofluoroethers and hydrofluoropolyethers

The thermal stability of representative hydrofluoropolyether (HFPE) and hydrofluoroether (HFE) compounds has been evaluated. The observed stability order appears to be correlated with the nature of the hydrogenated chain ends; in particular, molecules having fully hydrogenated chain ends (OCH₃ and OC₂H₅) show a significantly lower stability compared with the OCF₂H terminated compounds. The main degradation products suggest, however, that the same primary reaction is responsible for the decomposition of all the compounds examined; this reaction involves the fragmentation of the R_fOC_xH_yF_z bond with fluorine transfer between the two carbon atoms close to the oxygen, leading to the formation of a hydrofluorocarbon C_xH_yF_(z+1) and an acyl fluoride or a ketone.     

Polybutadiene cross-linked with various diols — effect on thermal stability

The relationship between cross-linking and thermal stability as related to polybutadiene is the focus of current research. Cross-linked polybutadienes have been prepared using various diols as the cross-linking agent. Cross-linked polymers have been characterized by gel content, swelling ratios, infrared spectroscopy, and thermal analysis. These polymers are not highly cross-linked, as seen by gel content and swelling ratios, and cross-linking does not have a large effect on the onset temperature of the degradation. Nonetheless, extensive formation of a non-volatile residue occurs.     

High mechanical and thermal performance of Sasobit-modified epoxy resin,prepared via vacuum shock technique

In this study, thermal and mechanical properties of novel nanocomposite, epoxy resin reinforced with octadecylamine functionalized graphene oxide (GO-ODA) and Sasobit, prepared via creative vacuum shock technique, were investigated. By introducing 1, 3 and 5 wt% Sasobit to the neat epoxy resin, the tensile strength increased remarkably by 104%, 315% and 266%, respectively due to the unique stiff and crystalline structure of Sasobit. In addition, considerable enhancement of 125% in Young's modulus, 351% in toughness, 562% in impact resistance, ~19 °C in thermal stability and ~7 °C in glass transition temperature of epoxy resin with 3 wt% Sasobit loading was demonstrated. The composite containing 3 wt% Sasobit alone, were found to have even superior properties than GO-ODA/epoxy nanocomposite, as surprisingly 3, 2.9, 2.2 and 2 times more improvement, respectively in tensile strength, toughness, impact strength and thermal stability of epoxy resin compared to reinforcement with GO-ODA were obtained.