Fe-Ni-BaTiO3复合材料的介电行为及其机理研究

利用金属铁、镍(Fe与Ni保持mol比为22∶78不变)与钛酸钡复合，在保护气氛下成功烧结制备了高介电常数Fe-Ni-BaTiO₃复合陶瓷材料，并研究了该复合材料的电导和介电性能及其物理机理.分析结果表明，由于渗流效应，随着陶瓷中金属含量的增加，材料经历了绝缘体—导体突变.同时，在渗流阈值附近，材料的介电常数有了极大的提高.当金属体积含量为0.23时，即在绝缘体向导体转变的渗流阈值附近，复合材料的介电常数达到了22000，为同条件下制备的纯钛酸钡陶瓷体介电常数的12倍，同时材料的介电 关键词： 3')" href="#">Fe-Ni-BaTiO₃ 渗流理论 介电性能 Maxwell-Wagner效应     

高储能密度铁电聚合物纳米复合材料研究进展

介电电容器具有超高功率密度、低损耗以及高工作电压等优点,是广泛应用于电子电力系统的关键储能器件.铁电聚合物是发展高储能密度电介质薄膜材料的理想选择,而基于铁电聚合物的纳米复合材料则兼具了聚合物的高击穿场强、柔性、易加工等特点以及陶瓷的高介电性能,是近年来电介质储能材料研究的前沿与热点.本文首先介绍了铁电聚合物材料的制备、铁电性能以及极化特性的调控方法,随后总结了铁电聚合物纳米复合材料中纳米填料、复合结构以及界面三个关键调控策略对复合材料介电与储能性能的影响,并探讨了基于相场方法的纳米复合材料中介电与储能特性的微观机制研究,最后对高储能密度铁电聚合物纳米复合材料现存问题以及未来发展方向进行了总结与展望.     

溶胶-凝胶法制备的高压电常数(Bi_(0.5)Na_(0.5))_(1-x)Ba_xTiO_3系无铅压电陶瓷

测量了使用溶胶 凝胶工艺制备的 (Bi0 5Na0 5) 1 -xBaxTiO3(x =0 0 0 ,0 0 4 ,0 0 6 ,0 0 8,0 12 )系陶瓷的介电、压电、铁电和热释电性能 .由于使用了溶胶 凝胶工艺制备的粉料 ,因此所有样品的压电性能都得到了较大提高 .其中(Bi0 5Na0 5) 0 94 Ba0 0 6 TiO3系陶瓷具有该系列最大的压电常数 ,d33=173× 10 - 1 2 C N ,与传统工艺相比 ,d33提高了近4 0 % .同时 ,在一定范围内 ,随Ba含量的增加 ,材料的剩余极化Pr 和矫顽场Ec 逐渐减小 ,退极化温度逐渐降低 .对于 (Bi0 5Na0 5) 0 94 Ba0 0 6 TiO3系陶瓷 ,剩余极化和矫顽场分别为 2 5 μC cm2 和 2 8kV cm ,退极化温度约为 80℃ .     

Pb(Mg_(1/3)Nb_(2/3))O_3-PbTiO_3/CoFe_2O_4复合薄膜电学、磁学性能的研究

利用射频磁控溅射技术在LaNiO_3/SiO_2/Si基底上制备了Pb(Mg_(1/3)Nb_(2/3))O_3-PbTiO_3/CoFe_2O_4和Pb(Mg_(1/3)Nb_(2/3))O_3-Pb TiO_3/Co Fe_2O_4/Pb(Mg_(1/3)Nb_(2/3))O_3-PbTiO_3两种复合薄膜.我们采取了三种退火条件对复合薄膜进行退火处理,研究两种复合薄膜的晶体结构、电学和磁学性能.通过对两种复合薄膜的结构的分析,发现两步法退火后得到复合薄膜同时存在纯钙钛矿相和尖晶石相两种结构.铁电性能测试表明,两种复合薄膜均具有较好的铁电性能,其中三层复合薄膜的剩余极化强度Pr最大可以达到14.9μC/cm2,这要归因于多层复合薄膜内部的应力-应变效应和界面耦合效应.在电场强度为80 k V/cm的漏电流密度数量级仅10-5A/cm2,其导电机制在高电场区满足Schottky机制.介频性能测试表明:复合薄膜的介频特性较差,双层复合薄膜的介电性能较好,其介电常数εr为1078,其介电损耗tgδ较大,约为0.43.此外,对复合薄膜的磁滞回线测试表明:两种复合薄膜中均存在磁学性能,且双层结构复合薄膜的铁磁性能较大,其饱和磁化强度Ms为119 emu/cm3,剩余磁化强度Mr达到31.6 emu/cm3,矫顽场Hc为1360 Oe.以上测试结果表明,铁电有序和磁有序可以存在于钙钛矿-尖晶石结构当中,通过多层复合和合适退火方式可以增强其铁电和介电性能.     

Pb(Mg1/3Nb2/3)O3-PbTiO3/CoFe2O4复合薄膜 电学、磁学性能的研究

利用射频磁控溅射技术在LaNiO3/SiO2/Si基底上制备了Pb(Mg1/3Nb2/3)O3-PbTiO3/CoFe2O4和Pb(Mg1/3Nb2/3)O3-PbTiO3/CoFe2O4/Pb(Mg1/3Nb2/3)O3-PbTiO3两种复合薄膜.我们采取了三种退火条件对复合薄膜进行退火处理,研究两种复合薄膜的晶体结构、电学和磁学性能.通过对两种复合薄膜的结构的分析,发现两步法退火后得到复合薄膜同时存在纯钙钛矿相和尖晶石相两种结构.铁电性能测试表明:两种复合薄膜均具有较好的铁电性能,其中三层复合薄膜的剩余极化强度Pr最大可以达到14.9 μC/cm2,这要归因于多层复合薄膜内部的应力-应变效应和界面耦合效应.在电场强度为80kV/cm的漏电流密度数量级仅10-5A/cm2,其导电机制在高电场区满足Schottky机制.介频性能测试表明:复合薄膜的介频特性较差,双层复合薄膜的介电性能较好,其介电常数εr为1078,其介电损耗tgδ较大,约为0.43.此外,对复合薄膜的磁滞回线测试表明:两种复合薄膜中均存在磁学性能,且双层结构复合薄膜的铁磁性能较大,其饱和磁化强度Ms为119 emu/cm3,剩余磁化强度Mr达到31.6 emu/cm3,矫顽场Hc为1360 Oe. 以上测试结果表明,铁电有序和磁有序可以存在于钙钛矿-尖晶石结构当中,通过多层复合和合适退火方式可以增强其铁电和介电性能.     

(K0.45Na0.55)NbO3无铅压电晶体的生长形态与介电性能研究

采用高温熔融法制备出了尺寸达5 mm×3 mm×1 mm的(K_0.45Na_0.55)NbO₃(KNN)无铅铁电晶体. XRD测试结果表明KNN晶体结构为纯的钙钛矿正交相结构,晶体的显露面为〈001〉结晶面. SEM显微结构分析表明晶体沿[001]方向呈现层状生长台阶,采用负离子配位多面体生长基元模型解释了晶体层状台阶的生长机理. 研究了晶体样品在室温至500 ℃温度范围内的介电性能,两个介电异常峰出现在240和405 ℃,分别对应正交铁电-四方铁电以及四方铁电-立方顺电相相变温度. 采用修正后的居里外斯定律研究了KNN晶体的介电弛豫特性,结果表明KNN晶体的介电弛豫特性接近于普通铁电体特征. 关键词： 0.45Na_0.55)NbO₃晶体')" href="#">(K_0.45Na_0.55)NbO₃晶体 无铅 晶体结构 介电性能     

La2/3Sr1/3MnO3/BaTiO3复合薄膜的制备及其电致磁电效应研究

使用脉冲激光沉积技术,在LaAlO₃(001)单晶基片上制备了La_2/3Sr_1/3MnO₃(LSMO)/BaTiO₃(BTO)双层薄膜.X射线衍射分析显示,LSMO层和BTO层呈现纯(001)取向.原子力显微镜研究表明,薄膜表面晶粒大小均匀,排列致密,表面均方根粗糙度为1.4 nm.复合薄膜的磁学、电学性能研究表明,其具有良好的磁学和介电性能.电输运测试显示,与在BTO层上施加正方向 关键词： 磁电效应 铁电/铁磁异质结构 脉冲激光沉积     

磁致伸缩/压电叠层复合材料磁-机-电耦合系数分析

分析和推导了磁致伸缩/压电叠层复合材料的机-电耦合系数、磁-机耦合系数及磁-电耦合系数与磁致伸缩层和压电层性能参数及几何参数之间的关系.进一步分析表明,叠层复合材料低频时的磁电电压系数正比于磁-电耦合系数,谐振时的磁电电压系数正比于磁-电耦合系数与机械品质因素的乘积;磁电电压系数还与复合结构的本征阻抗有关,本征阻抗越大磁电电压系数越大.通过性能差异较大的Terfenol-D和FeNi基弹性合金分别与压电材料PZT5-H和PZT8相互组合构成复合材料的比较分析,进一步阐明了磁电复合材料磁-电耦合系数和机械品 关键词： 磁电效应 磁-机-电耦合系数 磁致伸缩材料 压电材料     

溶胶-凝胶法制备的高压电常数（Bi0.5Na0.5）1－xBaxTiO3系无铅压电陶瓷

测量了使用溶胶-凝胶工艺制备的(Bi0.5Na0.5)1-xBaxTiO3(x=0.00，0.04，0.06，0.08,0.12)系陶瓷的介电、压电、铁电和热释电性能.由于使用了溶胶-凝胶工艺制备的粉料，因此所有样品的压电性能都得到了较大提高.其中(Bi0.5Na0.5)0.94Ba0.06TiO.3系陶瓷具有该系列最大的压电常数，d33=173×10-12C/N，与传统工艺相比，d33提高了近40%.同时，在一定范围内，随Ba含量的增加，材料的剩余极化Pr和矫顽场Ec逐渐减小，退极化温度逐渐降低.对于(Bi0.5Na0.5)0.94Ba0.06TiO.3系陶瓷，剩余极化和矫顽场分别为25μC/cm2和28kV/cm，退极化温度约为80℃. 关键词： 溶胶-凝胶 压电常数 剩余极化 矫顽场     

光学材料 光学塑料、光学陶瓷

TQ174.756 2006043636Bi4-xLaxTi3O12介电陶瓷的制备及其介电性能的研究=Preparation of Bi4-xLaxTi3O12dielectric ceramics and studyof their dielectric properties[刊,中]/何波(昆明理工大学光电子新材料研究所.云南,昆明(650051)) ,徐静…∥红外.—2006 ,27(3) .—21-27采用固相烧结法制备了不同掺La量、不同烧结工艺的铋层化合物Bi4-xLaxTi3O12(x=0 ,0 .25 ,0 .5 ,0 .75 ,1)介电陶瓷。利用宽频LCR数字电桥和XRD、SEM分析了Bi4-xLaxTi3O12介电陶瓷的晶相和微观结构对其介电性能的影响。研究表明,1 050 ℃烧结温度保温4 h…     

基体电导率对0-3型铁电复合材料高压极化行为及损耗的影响

提出了一个0-3型聚合物基铁电复合材料的直流高压极化模型.模型中考虑了聚合物/铁电陶瓷界面处自由电荷的积聚及极化初始时刻的真实情况,利用拉普拉斯静电场方程,并结合边界条件,得到了直流高压极化过程中复合材料的极化强度、界面电流密度等随时间的演化方程,同时得到介电常数、介质损耗等物理特性的表达式.此外,实验制备了分别以环氧树脂E-44和铁电共聚物P(VDF-TrFE)为基体的两种0-3型铁电复合材料.从理论和实验两方面研究了基体电导率对极化行为以及介质损耗的影响.两方面结果均表明：随基体电导率增加,极化时间缩短,陶瓷相的极化强度及复合材料的整体电性能提高,但是漏电流及介质损耗增加.而且实验结果与直流高压极化模型的预测结果符合. 关键词： 铁电复合材料 电导率 极化 介质损耗     

Electromechanical response of 2-2 layered piezoelectric composites: A micromechanical model based on the asymptotic homogenization method

A micromechanical model based on the asymptotic homogenization technique has been developed to predict the complete elastic, dielectric and piezoelectric properties of a general 2-2 layered piezoelectric composite where the constituent phases are elastically anisotropic and piezoelectrically active. Two classes of layered piezoelectric composites (i.e. longitudinally and transversely layered) are considered in two widely different ceramic- and polymer-based systems and their effective properties are obtained in the limits of both large-volume (i.e. bulk) and small-volume (i.e. thin-film) systems. It is demonstrated that: (i) in the bulk, ceramic–ceramic layered composite system, the elastic, piezoelectric, and dielectric properties of the composites vary linearly with volume fraction of the second phase, while in the bulk ceramic–polymer layered composite system, the corresponding properties vary non-linearly with volume fraction of the second phase; (ii) in the prismatic (thin-film) layered piezoelectric composite system, the non-vanishing, effective elastic, piezoelectric and dielectric properties vary linearly with the volume fraction of the second phase for both the longitudinally and transversely layered composite structures in the ceramic–ceramic and the ceramic–polymer composite systems; (iii) the ceramic–polymer piezoelectric layered composites that incorporate a low density polymeric phase with lower acoustic impedance generally exhibit enhanced piezoelectric coupling constants and lowered acoustic impedance; (iv) the longitudinally layered composites exhibit higher piezoelectric coupling constants and lower acoustic impedance compared to that of the transversely layered composites; and (v) the best combination of properties for applications such as hydrophones (i.e. the highest piezoelectric coupling constants and the lowest acoustic impedance) is obtained in the ceramic–polymer, longitudinally layered, thin-film, piezoelectric composites.     

Prediction of the properties of two-phase composites with a piezoactive component

The effective dielectric, piezoelectric, and elastic constants of two-phase macroscopically piezoactive 3-0 and 3-3 composites are calculated. It is assumed that one of the components is a polarized ferroelectric ceramic material and the other is an inactive material with variable elastic properties. The limiting case when the elastic compliances of the inactive material tend to infinity (porous ferroelectric ceramics) is considered. The adequacy of this model to production technologies of piezoelectric composites is discussed. Computational results are compared with experimental data.     

0-3型压电复合材料覆盖层水下 吸声性能的理论研究

目前压电分流阻尼技术在振动和噪声领域的应用得到了广泛的关注. 本文尝试将压电分流阻尼技术应用于水下吸声领域, 以提高覆盖层的吸声性能. 将压电覆盖层厚度模态的机电方程和声波传播的传递矩阵相结合, 建立一维电声模型. 该模型可以用于分析多层压电和非压电水下吸声覆盖层的吸声性能. 采用该模型分析了0-3型压电复合材料覆盖层的水下吸声性能. 压电复合材料的参数是采用Furukawa的模型计算的. 研究结果表明, 采用合适的分流电阻, 负电容分流电路可以在较宽的频率范围显著提高覆盖层的吸声性能. 其原理可以从阻抗匹配的角度解释, 负电容分流电路可以调整压电覆盖层的表面声阻抗, 使之与水的特性声阻抗相匹配.     

改进型1-3压电复合材料结构参数对其谐振性能的影响

研究了水声换能器用的1-3改进型(称1-3-2型)压电复合材料的结构参数(陶瓷体积分数)对其谐振性能的影响.1-3-2型压电复合材料是由1-3型复合材料和陶瓷基底两部分组成,利用Newnham串并联理论、均匀场理论和混合定律,得到1-3-2型复合材料的压电方程,从而推导出1-3-2型复合材料的各项等效性能参数,并通过实验对频率常数、机电耦合系数和声阻抗等参数的理论推导进行了验证,实验结果与理论计算符合较好。     

Percolative effects and giant dielectric tunability of BaTiO3–LuFe2O4 composites

We report on exotic dielectric properties of composite materials consisting of traditional ferroelectric BaTiO₃ and electronic ferroelectric LuFe₂O₄. The composites were synthesized by a simple ceramic processing method with properties that can be tailored by adjusting LuFe₂O₄ concentration. A percolative effect was observed at the volume fraction of ～0.26, which led to an abrupt increase in the dielectric permittivity. For composites with high LuFe₂O₄ fractions, a giant dielectric tunability was observed over a broad temperature interval, which is in strong contrast to traditional ferroelectrics.     

聚丙烯蜂窝膜驻极体压电系数的测量及压电性的改善

利用介电谐振谱分析了聚丙烯蜂窝状原生膜(PPCellular,PQ50型)的力学及介电参数，测得其压电系数d33约为18pC/N.经合理的压力膨化工艺处理后，其d33可增加至367pC/N，比久负盛名的铁电聚合物聚偏氟乙烯(PVDF)的d33高20倍以上，也高于压电陶瓷锆钛酸铅(PZT)的相应值.结合扫描电镜照片及根据PP蜂窝膜压电理论模型分析了这类空间电荷型非极性孔洞薄膜驻极体呈现高压电系数的结构和物理根源. 关键词： 聚丙烯蜂窝膜 压电性 介电谐振 压力膨化处理     

Structural and dielectric properties of polyvinyl alcohol/barium zirconium titanate polymer–ceramic composite

The polyvinyl alcohol (PVA)/barium zirconium titanate Ba[Zr_0.1Ti_0.9]O₃ (BZT) polymer–ceramic composites with different volume percentage are obtained from solution mixing and hot-pressing method. Their structural and electrical properties are characterized by X-ray diffraction (XRD), Rietveld refinement, cluster modeling, scanning electron microscope and dielectric study. XRD patterns of PVA/BZT polymer–ceramics composite (with 50% volume fractions) indicate no obvious differences than the XRD patterns of pure BZT which shows that the crystal structure is still stable in the composite. The scanning electron micrograph indicates that the BZT ceramic is dispersed homogeneously in the polymer matrix without agglomeration. The dielectric permittivity (ε_r) and the dielectric loss (tan δ) of the composites increase with the increase of the volume fraction of BZT ceramic. Theoretical models are employed to rationalize the dielectric behavior of the polymer composites. The dielectric properties of the composites display good stability within a wide range of temperature and frequency. The excellent dielectric properties of these polymer–ceramic composites indicate that the BZT/PVA composites can be a candidate for embedded capacitors.     

A study of a 1-3-2 type piezoelectric composite

A novel 1-3-2 type piezoelectric composite is developed. There are piezoelectric ceramic framework supports at transverse and longitudinal directions in its structure, so it is free from the influence of any outside mechanic impact and environmental temperature change. The sample characteristic is good coherence. It has many advantages, such as a high piezoelectricity, lower density and acoustic impedance matching with water and tissue easily. Based on Newnham's series and parallel theory of composites, the calculation formulae of dielectric and piezoelectric constants of a 1-3-2 type piezoelectric composite are deduced. The sample's characteristics indicate that a 1-3-2 type piezoelectric composite's theoretic calculation values are in good agreement with the measurement results. Element samples have been designed, manufactured and measured. The results indicate that the resonant frequency, resonant impedance, piezoelectricity and static capacity of these samples are stable. It is easy to design sensor array elements using this material.