HDPE/PA6反应增容体系的形态演化与黏弹行为

采用扫描电子显微镜(SEM)与先进流变扩展系统(ARES),研究了马来酸酐接枝高密度聚乙烯(HDPE-g-MAH)对高密度聚乙烯/尼龙6(HDPE/PA6)共混体系形态结构和黏弹行为的影响.发现HDPE-g-MAH的加入可原位生成尼龙6-高密度聚乙烯接枝共聚物(HDPE-g-PA6),使基体与分散相间的相容性显著改善,且随其添加量的增加两者相容性更好,导致HDPE/PA6体系形态结构变化.研究结果表明,由ARES获得的体系黏弹行为参数随HDPE-g-MAH含量的变化可与由SEM所观察到的微观形貌演化很好关联,动态流变学方法可敏感表征增容剂的加入所引起的HDPE/PA6界面性质变化,且能够反映分子链间相互作用的变化及由此导致的分散相颗粒网络的形成.     

高密度聚乙烯/丁基橡胶共混体系形态与性能的研究

高密度聚乙烯(HDPE)与丁基橡胶(IIR)共混后,耐环境应力开裂性(ESCR)和抗冲击强度得到了提高。当IIR含量小于50％时,共混物中HDPE的晶格、结晶度、熔点保持未变。随IIR含量的增加,进入HDPE片晶间无定形区域的IIR量增加。少量IIR链段沿HDPE片晶厚度方向把一些片晶连接起来,共混物的抗冲击强度和ESCR因而获得显著提高。     

HDPE／LDPE共混体系的晶性研究

用DSC和WAXD方法考察了高密度聚乙烯和低密度聚乙烯共混体系(HDPE/LDPE)的结晶性能。结果表明,在共混物中HDPE含量大于50%时,共混物只出现HDPE的熔融峰,且熔融温度随HDPE含量减小而降低;LDPE含量大于50%时,DSC图上只出现熔点介于HDPE和LDPE之间的新熔融峰。DSC和WAXD法所测结晶度均偏离共混物的线性加和值,而晶胞参数则随共混物组成变化出现最小值,表明HDPE和LDPE可以形成共晶相容体系。Raman光谱测得介晶相αb值的膨胀,支持这一观点。     

高密度聚乙烯与EPDM磺酸锌盐共混物结构与性能的研究

本文研究了高密度聚乙烯(HDPE)/EPDM磺酸锌盐(Zn-SEPDM)共混物的机械性能、流变行为、形态和相容性。结果表明:加入Zn-SEPDM可使HDPE的熔点和结晶度降低,熔程变窄。当Zn-SEPDM含量超过20％,共混物中Zn-SEPDM呈连续相,冲击强度突增。     

γ-射线辐照法制备HDPE/PA6阻隔性材料及其性能研究

研究了富氧气氛中高密度聚乙烯(HDPE)的γ-射线辐照氧化及其与尼龙-6(PA6)的共混增容和共混材料的阻隔性能.FT-IR测试结果表明, 经γ-射线辐照的HDPE与PA6发生了化学反应或产生了弱相互作用.SEM照片显示4γHDPE (4h辐照,66Gy/min)与PA6具有良好的相容性,PA6在共混体系中呈层状分布.共混材料的阻隔性能测试结果表明4γHDPE/PA6共混物对二甲苯的阻隔性较HDPE/PA6共混物有明显提高.力学性能测试显示4γHDPE/PA6共混物力学性能优良.     

紫外线辐照光强对HDPE化学结构及对HDPE/PC共混体系增容效应的影响

采用FT-IR,XPS,凝胶分析以及熔融指数、接触角和力学性能测定,研究了不 同紫外辐照光强对高密度聚乙烯（HDPE）的化学结构、流动性、亲水性和辐照改性 HDPE在HDPE/聚碳酸酯（PC）共混体系中的增容效应的影响。在相同辐照时间下, 随紫外光强提高,引入HDPE分子链的含氧基团数量增加;在辐照过程中,紫外光强 对HDPE的交联有显著影响,在较低光强（32W/m~2）下辐照24h的HDPE无凝胶生成, 便在较高光强（45和78W/m~2）下辐照24h后,HDPE产生凝胶,其含量随紫外光强提 高而增多;与未辐照HDPE相比,较高光强下辐照HDPE的熔融指数有所下降,但其亲 水性得到明显改善;紫外辐照改性HDPE对HDPE/PC体系有增容作用,随紫外光强提 高其增容效应明显增强。与未增容HDPE/PC（80/20）体系相比,加入20%辐照 24hHDPE（光强78W/m~2）的HDPE/PC共混物的拉伸屈服强度从26.3MPa提高到30. 2MPa,缺口冲击强度从51J/m提高到158J/m。     

POE-g-PMAH反应性增容PA1010/PP共混物的性能研究

乙烯-辛烯共聚物-g-聚马来酸酐(POE-g-PMAH)作为反应性增容剂,采用熔体共混的方法制备了PA1010/PP共混物,通过扫描电镜(SEM)、力学性能、傅立叶变换红外光谱(FTIR)和示差扫描量热(DSC)测试,研究了POE-g-PMAH对PA1010/PP共混物的增容作用.结果表明,POE-g-PMAH的加入可以减小共混物的相区尺寸,当PA1010/PP/POE-g-PMAH=70/30/15时,分散相尺寸小而均匀;FTIR结果表明接枝在POE上的马来酸酐基团和PA1010在熔融共混期间发生了化学反应;DSC研究结果表明共混体系中PA1010和PP的结晶温度和结晶度随POE-g-PMAH的加入而降低,表明POE-g-PMAH的增容作用对PA1010和PP的结晶有抑制作用.力学性能测试结果表明随着POE-g-PMAH的增加,共混物的冲击强度逐渐增加,当POE-g-PMAH含量增加到15%时,干态冲击强度达到21.13 kJ/m2,是不加增容剂的3.1倍,而拉伸和弯曲强度可以保持较高水平.POE-g-PMAH的增容机理在于其支链中的马来酸酐能与PA1010中的胺基(NH2—)发生化学反应,而主链POE与PP有较好的亲和性,从而降低界面张力,减少相区尺寸,大幅度提高力学性能.     

应力引发官能化EPDM/HDPE及其对PA66/EPDM/HDPE 共混物相形态和力学性能的影响

通过提高双螺杆挤出机螺杆转速的方法,研究了熔融挤出过程中高剪切应力对马来酸酐(MAH)官能化三元乙丙橡胶(EPDM)与高密度聚乙烯(HDPE)共混物的接枝率、熔体流动速率及凝胶含量的影响.随着双螺杆挤出机螺杆转速的增加,强烈的机械剪切应力引发EPDM/HDPE共混物大分子链的断链反应形成大分子自由基,从而引发接枝反应制...     

PP-g-(GMA-co-St)对PA6/PC共混物的反应增容作用

用红外、扫描电镜、熔体流动速率和力学性能等测试方法,研究了甲基丙烯酸缩水甘油酯(GMA)和苯乙烯(St)多单体熔融接枝聚丙烯[PP-g-(GMA-co-St)]对PA6/PC共混物的反应增容作用.研究结果表明,在熔融共混过程中,PP-g-(GMA-co-St)中的环氧基与PA6的端氨基及PC的端羟基原位生成的接枝共聚物有效地降低了共混物相间的界面张力,明显提高了共混物相界面的粘着力.少量的PP-g-(GMA-co-St)就能使PA6和PC的相容性得到显著改善.当PP-g-(GMA-co-St)的质量分数为10%时,共混物分散相的相区尺寸细化到0.2μm,其力学性能也有较大提高.PA6/PC/PP-g-(GMA-co-St)共混物的力学性能均衡,达到了弹性体增韧体系难以达到的效果.即使PP-g-(GMA-co-St)组分含量为20%时,共混物仍能保持较好的力学性能,特别是在共混物的韧性得以提高的同时,其强度和伸长率也提高.     

PP/HDPE 共混物及其纳米复合材料超临界流体微孔发泡

通过间歇法制备了聚丙烯(PP)/高密度聚乙烯(HDPE)共混物及其纳米复合材料的微孔塑料.用扫描电镜对发泡样品的泡孔结构进行表征,研究了纳米粒子的类型和含量对泡孔结构的影响.结果表明:在PP中加入25%的HDPE可改善泡孔结构;在 PP/HDPE 共混物中加入纳米粒子可使泡孔的直径减小、密度增加、泡孔分布更均匀;泡孔直径随着纳米粒子含量的增加会出现先减小后增加的趋势.     

Solvent extraction separation of In/III/-Tl/III/ and Hg/II/-Cd/II/-Co/II/ with sulphoxides

Solvent extraction studies have been made on some metals: In/III/-Tl/III/ and Hg/II/-Cd/II/-Co/II/, from ammonium thiocyanate solutions by dialkyl sulphoxides. Separation of these metals from one another can be achieved by suitable choice of the extracted conditions. The nature of the extractable metal species has been elucidated.     

Simultaneous propane dehydrogenation andco2hydrogenation overCrOx/SiO2catalyst

Summary Single reverse water-gas shift (RWGS) and dehydrogenation of propane with CO₂(DH-CO₂) reactions in the presence and absence of the CrO_x/SiO₂ catalyst have been studied between 673 and 873 K. It was found that the CrO_x/SiO₂ catalyst is active both in the dehydrogenation of propane and in the RWGS reactions. The obtained results suggest that the dehydrogenation of propane to propene in the presence of CO₂on CrO_x/SiO₂can be facilitated by the RWGS reaction.</o:p>     

Synthesis of chlorobis/β-diketonato/oxotechnetium/V/ and tris/β-diketonato/technetium/III/ complexes

Chlorobis/-diketonato/ oxotechnetium/V/ complexes [TcOCl/-dik/₂, -diketone=acetylacetone, benzoylacetone and dibenzoylmethane] were newly synthesized using macroamount of⁹⁹Tc. These complexes were further separated into geometrical isomers. Furthermore, an improvement of the yields for the syntheses of tris/-dike-tonato/technetium/III/ complexes [Tc/-dik/₃, -diketone=acetylacetone, benzoylacetone and 2-thenoyltrifluoroacetone] was examined using Tc/III/-thiourea complexes as a starting material.     

Direct synthesis of dimethyl carbonate ?from CH3OH AND CO2 by H3PW12O40/CexTi1-xO2 catalyst

Summary Ce_xTi_1-xO₂ and H₃PW₁₂O₄₀/Ce_xTi_1-xO₂ catalysts were prepared using a sol-gel method, and applied to the direct synthesis of dimethyl carbonate from methanol and carbon dioxide. H₃PW₁₂O₄₀/Ce_xTi_1-xO₂ showed a better catalytic performance than the corresponding Ce_xTi_1-xO₂, due to the bifunctional catalysis of Br?nsted acid sites (provided by H₃PW₁₂O₄₀) and base sites (provided by Ce_xTi_1-xO₂). H₃PW₁₂O₄₀/Ce_0.1Ti_0.9O₂ showed the highest catalytic performance among the H₃PW₁₂O₄₀/Ce_xTi_1-xO₂ catalysts.     

Crystal structure of Na3PO4 · 12H2O

The crystal structure of trisodium monophosphate hemihydrate was determined. The space group is $\text{C2}\text{c}$ and a unit cell contains eight formula units. The unit cell dimensions of $\text{Na}{}_3\text{PO}{}_4\text{·}\text{1}\text{2}\text{H}{}_2\text{O}$ are a = 9.631(3), b = 5.416(2), c = 16.938(8) Å, β = 102.60(5)°. The final R value is 0.027 for a set of 1430 independent reflections. This atomic arrangement is mainly a three-dimensional network of distorted NaO₆ octahedra. The hydrogen bonding scheme is given.     

LixNi0.8-yCo0.2ZnyOp的合成及电化学性能研究

A series of single-phase Li_xNi_0.8-yCo_0.2Zn_yO_p(0.96 ≤x≤ 1.10， 0 ≤y≤ 0.05， 2 ≤p≤ 2(1+y) ) (different in the y values) were synthesized by a two-step solid state reaction method， in which LiOH·H₂O， Zn-doped spherical Ni(OH)₂ and Co₂O₃ were used as the precursors. The ICP-AES analyses proved that the Zn-doped compounds synthesized had the nonstoichiometric form. The results of the XRD， SEM identified that the uniform particles of the as-prepared materials having a good layered structure were fine， narrowly distributed and well crystallized. The electrochemical performance test was carried out and the results showed that the as-prepared Zn-doped materials had not only a high capacity， but also a better cycling stability characterization than the un-doped one. The Li_1.06Ni_0.75Co_0.22Zn_0.03O_2.03 material has an initial reversible capacity as high as 160.5mAh·g^-1; and a first discharge efficiency 89.2%， and exhibits satisfactory cyclic stability with 90% retainable capacity after 50 cycles.     

Synthesis and characterization of Ti1−2xNbxNixO2−x/2 solid solutions

Doped-rutile has been traditionally used in ceramic pigments for its intense optical properties. In this paper, we compare the classical ceramic synthesis of Ti_1−2xNb_xNi_xO_2−x/2 system with the sol-gel methodology, which allows a reduction of the anatase-rutile transformation temperature. The composition was optimised in order to obtain a unique rutile phase with the minimum amount of pollutant Ni(II) and enhanced chromatic coordinates. Incorporation of the doping ions in the rutile structure was corroborated by XRD and Rietveld refinements. The species responsible for the colour mechanism were studied by different techniques. UV-VIS spectroscopy showed the characteristic features of Ni²⁺ ions, whose existence was corroborated by EPR and magnetic measurements. From these results, (Ni,Nb)doped-TiO₂ powder samples can be now shaped as thin films, monoliths, etc. by using sol-gel methodology without modifying their properties. This study introduces new possibilities of coloured TiO₂-based solid solutions in new combined advanced applications (colouring agent and photocatalyst, etc.).     

An investigation of the promotional effect of propylene or propane traces on the activity of sulfatedPt/g-Al2O3andPt-Sn/g-Al2O3inCH4combustion

Summary A strong promoting effect of the presence of C₃H₈or C₃H₆was determined for the combustion of CH₄in excess oxygen, over pre-sulfated 1%Pt/g-Al₂O₃and pre-sulfated 1%Pt-2%Sn/g-Al₂O₃catalysts.</o:p>     

Visible light-sensitive yellow TiO2−xNx and Fe-N co-doped Ti1−yFeyO2−xNx anatase photocatalysts

Nitrogen substituted yellow colored anatase TiO_2−xN_x and Fe-N co-doped Ti_1−yFe_yO_2−xN_x have been easily synthesized by novel hydrazine method. White anatase TiO_2−δ and N/Fe-N-doped samples are semiconducting and the presence of ESR signals at g ∼1.994-2.0025 supports the oxygen vacancy and g∼4.3 indicates Fe³⁺ in the lattice. TiO_2−xN_x has higher conductivity than TiO_2−x and Fe/Fe-N-doped anatase and the UV absorption edge of white TiO_2−x extends in the visible region in N, Fe and Fe-N co-doped TiO₂, which show, respectively, two band gaps at ∼3.25/2.63, ∼3.31/2.44 and 2.8/2.44 eV. An activation energy of ∼1.8 eV is observed in Arrhenius log resistivity vs. 1/T plots for all samples. All TiO₂ and Fe-doped TiO₂ show low 2-propanol photodegradation activity but have significant NO photodestruction capability, both in UV and visible regions, while standard Degussa P-25 is incapable in destroying NO in the visible region The mid-gap levels that these N and Fe-N-doped TiO₂ consist may cause this discrepancy in their photocatalytic activities.     

LixZryOz三元化合物的制备及表征

采用高温固相法制备了4种高纯度晶相组成的LixZryOz三元化合物,研究了焙烧温度、时间、反应物的种类和初始反应物物质的量比对产物组成的影响,进一步用XRD、SEM及BET分析方法对产物的晶相结构、表面形貌及比表面积进行了表征.实验结果表明,Li2CO3与ZrO2在适当条件下可以合成得到单斜相Li3ZrO3;以LiOH替代Li2CO3,在适当条件下可以分别合成得到四方相Li2ZrO3和三斜/单斜相Li6Zr2O7;进一步以Zr(NO3)4·5H2O代替Zr02,可将单斜相Li6Zr2O7的制备时间由96 h缩短至24 h.SEM照片显示产物硬团聚明显,粒径分布在1～10μm间,BET分析表明样品比表面积处于1.0～9.0 m2·g-1间分布,反应过程中锂的过量以及长时间高温焙烧是引起产物粒径长大和产生硬团聚的主要原因.