Laser Diode Pumping High-stability 1047 nm TEM00 Mode CW Nd:YLiF4 Laser

A laser diode (LD) pumping high-stability 1047 nm TEM00 mode Nd: YLiF4 (Nd: YLF) continuous wave (CW) laser is reported in this letter. The laser output power of 5.83 W with optical to optical effidency of 27% and slope efficiency of 30% has been achieved The instability of output power is 0.36% and spike caused by relaxation oscillation has not been observed in the laser beam. The transverse cross section of laser beam is an ellipse, the diameters of laser beam at output mirror in both directions are 0.97 mm and 1.07 mm, respectively. The divergent angles are 0. 936 mrad and 0. 774 mrad, and the values of M2 are 1.37 and 1.24, respectively. The polarization degree of laser beam is better than 237:1.     

大功率准连续Nd:YAG陶瓷激光器研究

采用侧面环绕均匀排布的紧凑型抽运结构,实现了激光二极管阵列侧向抽运Nd∶YAG陶瓷激光器高效率激光输出。理论计算得到谐振腔输出镜的最佳输出耦合透射率为22.2%,并在输出耦合镜透射率为22%的条件下,用掺杂原子数分数为1%,尺寸为5mm×75mm的Nd∶YAG陶瓷棒,获得了平均功率大于230W的准连续1064nm激光输出,其光光效率和斜率效率分别高达52.4%和61%。并测得输出激光脉冲宽度为160μs,光谱线宽略小于0.8nm,光束发散角为16mrad。实验结果显示,Nd∶YAG陶瓷激光器输出功率Nd∶YAG单晶激光器相当。     

Three-Rod Resonator for Krypton Lamp Pumped 1.8 kW Continuous-Wave Nd：YAG Laser

A three-rod series resonator cw Nd:YAG laser suitable for the industrial applications is presented. The symmetrical resonator laser has been developed and is rated at 1820-W output power with beam parameter product 24 mm.mrad. By utilizing the symmetrical resonator design, the characteristic of beam with multi-rod is not obviously decreased compared with that of a single one. The system total electro-optics efficiency of lamp pumped YAG crystal is as high as 4.0%. The main factors, which affect output power and beam quality of high power solid-state laser module, are theoretically analysed.     

647W灯泵浦大功率连续Nd:YAG激光器

报道了一台灯泵浦大功率连续Nd:YAG激光器。对影响大功率固体激光器模块输出功率和光束质量的主要因素进行了理论分析,并提出提高激光器效率的措施：对聚光腔的形状、结构和材料以及冷却方式,泵浦灯的参数和材料,激光晶体的参数和镀膜进行优化设计,采用径向固定的谐振腔镜。该灯泵浦YAG晶体棒总体电光转换效率为4%,光束质量为22mm·mrad,输出功率647W。     

647W灯泵浦大功率连续Nd:YAG激光器

 报道了一台灯泵浦大功率连续Nd:YAG激光器。对影响大功率固体激光器模块输出功率和光束质量的主要因素进行了理论分析，并提出提高激光器效率的措施：对聚光腔的形状、结构和材料以及冷却方式，泵浦灯的参数和材料，激光晶体的参数和镀膜进行优化设计，采用径向固定的谐振腔镜。该灯泵浦YAG晶体棒总体电光转换效率为4%，光束质量为22mm·mrad，输出功率647W。     

高平均功率六棒串接脉冲Nd:YAG激光器

报道了一种腔内六棒串接的脉冲Nd:YAG激光器。采用44矩阵对晶体棒失调角度对谐振腔光轴的影响进行了理论分析,给出了六棒串接脉冲激光器中晶体棒失调角度的允许范围。在串接实验中,谐振腔采用对称平平腔结构,通过调整每根晶体棒的失调角度到允许范围内,实现了六棒串接脉冲Nd:YAG激光器。在输入电功率86 kW,占空比17%时,获得了平均功率3 018 W的脉冲激光输出,峰值功率17.75 kW,最高单脉冲能量为66 J,光束参数乘积为26.3 mmmrad,电光转换效率3.5%,长时间工作不稳定性小于2%。     

激光二极管端泵微片固体激光器的研究

本文介绍了一种用波长为809nm的激光二极管(LD)端面泵浦厚度为1mm的微片Nd:YVO4全固化固体激光器。器件结构上采用了一种独特的光学系统,该系统由分别用于LD激光束的耦合和聚焦的两部分组成。由Nd:YVO4的一个平面与一个曲率半径为21mm的球面镜组成半共焦腔,以获得高的转换效率。文中详细讨论了单横模运转时的泵浦光与激光腔模之间的匹配问题。当泵浦光功率为400mW时,获得152mW的1064nm波长的TEM00模激光输出。器件阈值功率为48.3mW,总的光-光转换效率为38%,斜效率为43%.     

600-W lamp pumped CW Nd:YAG laser

A lamp pumped CW Nd:YAG laser is presented in this paper for the requirement of industrial application. The main factors, which affect output power and beam quality of high power solid-state laser module, are theoretically analyzed. Total electro-optics efficiency of lamp pumped Nd:YAG crystal as high as 4.0% is obtained, and output power is higher than 647 W with beam parameter product 22 mm·mrad.     

200 mJ半导体端面泵浦MOPA激光器研究

采用高功率激光二极管阵列(LDA)端面泵浦Nd:YAG激光棒方式, 结合凸凹非稳腔的设计，获得20 Hz运转条件下小束散角激光输出平均能量约为83 mJ。以该激光为振荡源，同样采用LDA端面泵浦Nd:YAG激光棒的方式进行能量放大，组成LDA端面泵浦振荡-放大(MOPA)激光器，最终获得重频频率20 Hz、平均能量＞200 mJ、发散角＜2.1 mrad、能量波动＜±2.5%的脉冲激光输出。该激光器光光转换效率约为14.6%，体积为175×91×49 mm3，质量＜1 kg，激光经8倍发射天线后发散角＜0.3 mrad。     

高功率高光束质量脉冲Nd: YAG激光器

以实现高功率、高光束质量的脉冲激光输出为目的,对非对称平-凹谐振腔的结构进行了理论分析。设计出了高功率、高光束质量非对称放置的平-凹谐振腔、双氙灯泵浦的脉冲Nd: YAG激光器。当占空比为9%时,实现输出激光平均功率近480 W,光束参数积优于12.7 mm·mrad,电光转化效率近4%,与理论分析吻合,可用芯径300 μm的光纤传输,不稳定性优于±1%。加工实验证明有较好的质量：切割材料为不锈钢,厚度为3 mm时、切割速度为0.6 m/min和厚度为1.5 mm、切割速度为1.2 m/min时,两种情况下所得切缝宽度均为250 μm,且切割上下沿光滑。     

千瓦级半导体抽运的固体热容板条激光器

报道了千瓦级激光二极管面阵抽运固体热容激光器的理论与实验研究,分别采用Nd∶YAG单板条和双板条串接的热容激光器,利用热容激光器的理论计算模型计算了在一定的工作时间内激光输出特性,并进行了实验验证。实验中采用的晶体尺寸均为59mm×40mm×4.5mm,对单板条进行抽运时平均功率大约为5.6kW,双板条串接时为11.2kW,重复频率为1kHz,占空比为20%。实验中观察了1s的工作时间内脉冲能量输出的波动情况,单板条时单脉冲能量输出最大为1.3J,在1 s后单脉冲能量输出下降到开始的70%左右,而双板条串接时单脉冲能量输出最大为2.06J,在1s后单脉冲能量输出下降到开始的50%左右,对单块晶体采用通水冷却的准热容热管理模式能有效地降低其热效应。     

热效应对高功率b轴Nd+CrNd:YAP连续激光器输出的影响

本文在文献[1]的基础上提出了含有椭圆折射率分布介质谐振腔的设计方法。分析了b轴_Nd+Cr^Nd:YAP连续激光器中热效应对激光横向场分布,输出偏振方向以及输出功率的影响。考虑了这种影响后,已从φ5.8×111mm的Nd:YAP棒和φ6.4×100mm的Nd+Cr:YAP棒中得到了163W和152W的输出,器件效率分别为2.26％和2.11％,输出激光的退偏度为1/2900 关键词：     

适用于金属薄板焊接的柔性光纤耦合半导体激光加工光源

研制了一种单光纤耦合的柔性半导体激光加工光源,该光源由20个传导热沉封装的激光列阵以线阵合束方式耦合而成,在大通道工业水冷条件下,从600 μm芯径、NA为0.2的光纤中连续输出907 W功率,输出光束质量为47 mm·mrad,最终达到工件表面的功率密度为3.21×10⁵ W/cm²,最大插头效率达39%。该激光光源具有直接应用在金属薄板焊接的潜力。     

四棒串接连续灯泵浦Nd:YAG大功率激光器

 报道了一种符合工业应用的四棒谐振腔连续Nd:YAG激光器。实验中采用对称放置方式四棒串接谐振腔得到2 105 W的平均功率输出，光束参数积24 mm·mrad，系统总光电转换效率达到3.5%。还对影响激光器工作的因素进行了理论分析。     

Efficient 15-W CW Nd: YVO4 Solid-state Laser Single-end-pumped by a Fiber-coupled Diode-laser-array

1IntroduCtion~e-laserarrayendpumpedsolid-statelasersWthoutputpoWrgreaterthan1o-WareattractinggreatattentionowtngtothenumerousPotentialaPplicationsofsuch....[','].HoWever,progressinscalingendpumpedlaserstohighPOWershasbeengTeatlyhinderedbythermallensingandthermally-inducedfractureoflasercrystals.ExhibitingstrongthermallensingandhavingrelativelylDWfracturelidrit,theNdtYVOcrystalhasreceivedlitt1eattentioninthefieldofsingle-end-pumPedhigh-powerlasersinspiteofitssultabilityfordiode-1aser..d-…     

角锥棱镜腔激光二极管抽运被动调Q激光器

为了提高传导冷却条件下激光二极管(LD)侧向抽运被动调Q激光器的光束质量和输出稳定性,采用了两组半圆柱面激光二极管阵列侧向交错抽运两根串接的激光棒,实现了均匀抽运和散热。通过实验分析了横模结构对被动调Q稳定性的影响,设计了角锥棱镜-高斯输出镜非稳腔,在显著提高器件光束质量的同时,明显改善了被动调Q的稳定性,并保证了谐振腔的机械稳定性。在此基础上研制了一台重复频率20 Hz、单脉冲能量64 mJ、脉冲宽度7 ns、稳定性优于±5%、光束发散角0.6 mrad、光-光效率9.1%,且光轴指向稳定的工程实用器件。     

High power CW diode-side-pumped Nd:YAG rod laser

We report on the characterization of a diode-side-pumped Nd:YAG rod laser operating at high CW output power. A four-fold pump configuration is designed and the pump light is directly coupled into the Nd:YAG rod without the help of any cylindrical lenses. The distribution of pump light in the Nd:YAG rod has been calculated by using ray tracing program. The thermal lens effect of the Nd:YAG rod has been experimentally measured. A maximum output power of 800 W at 1064 nm in multimode operation is obtained for a pump power of 2400 W with 33% optical-optical efficiency. At the same time, the maximum beam parameter product of 25 mm·mrad is achieved.     

LD泵浦固体激光器基模振荡光的场分布噪音

通过调整泵浦光直径,使得LD端面泵浦固体激光器的振荡光工作于基模.在排除高阶横模的条件下,测量了由于热透镜的不稳定引起的光场场分布的噪音.实验发现,基模振荡光的高斯半径、光束指向角都在波动,而且光斑存在畸变波动.对一个未采取抑制措施的2W连续LD端面泵浦Nd:YAG固体激光器进行了测量.结果表明,在总功率不变的情况下,激光束峰值点附近的光强波动达到6.3%;激光的高斯半径波动达到5.8%;激光的指向角波动达到0.3mrad.     

高效率LD端面抽运准连续355 nm激光器

报道了一台激光二极管（LD）端面抽运Nd：YVO₄晶体腔内倍频和腔外和频相结合的声光调Q准连续355 nm 紫外激光器。采用LD端面抽运双侧翼键合YVO₄基质的Nd：YVO₄晶体,在腔内置入Ⅰ类相位匹配的LiB₃O₅（LBO）晶体进行倍频实现1 064 nm和532 nm双波长准连续激光输出,通过消色差透镜将双波长激光聚焦耦合到Ⅱ类相位匹配的LBO 晶体中进行和频,并采用双向和频光路,获得了高效率、高光束质量、高重复频率的准连续355 nm 紫外激光输出。在抽运功率为28.6 W、重复频率为20 kHz时,355 nm激光最大输出功率4.2 W,脉宽为20.6 ns,光-光转换效率为14.7%,激光器光束质量因子M_x²和M_y²分别为1.29和1.23。     

Design and construction of a 110 W green laser for medical application

In this paper, the design and the construction of a high-power side-diode-pumped Nd:YAG solid-state laser at repetition rates of 6 and 10 kHz has been presented. Second harmonic of the Nd:YAG laser with green light at 532 nm, with an average power of 111.5 W at 10 kHz repetition rate, and with 90 ns pulse duration, has been obtained by the nonlinear crystal of KTP with 59% conversion efficiency and 12% diode-to-green optical–optical efficiency in the linear resonator. Beam spot size and divergence is 4 mm and 8 mrad, respectively. The laser stability is about 97%. As a medical application of this laser, investigation of degree of effectiveness and penetration depth of laser on adenomas of resected prostate after open prostatectomy has been done.