Amorphous Structures in Laser Cladding of ZL111 Aluminum Alloy:Semi-quantitative Study by Differential Thermal Analysis (DTA)

This paper deals with amorphous structures in the laser cladding. ZL111 alloy is the substrate and Ni-Cr-Al alloy is sprayed on the substrate as the coating material. The coating is clad by a 5 kW transverse flow CO2 laser. The observation of SEM and TEM reveal that in the laser cladding there are amorphous structures of two different morphologies: one is space curved flake-like, and exists in the white web-like structures; the other is fir leaf-like, and exists in the grain-like structures. Differential thermal analysis (DTA) is used to semi-quantitatively determine the content of the amorphous structures. A relation is obtained between the content of amorphous structures and the dimensionless laser cladding parameter C. We also show the changes of the amorphous structures after annealing.     

Composition design and laser cladding of Ni-Zr-Al alloy coating on the magnesium surface

The cluster line criterion was used for optimized design of a Ni-Zr-Al alloy used as coating on the AZ91HP magnesium alloy by laser cladding. Results show that the coating mainly consists of an amorphous, two ternary intermetallic phases with Ni₁₀Zr₇ and Ni₂₁Zr₈ type structures resulting in high hardness, good wear resistance and corrosion resistance. The interface between the clad layer and the substrate has good metallurgical bond.     

Study on modes of energy action in laser-induction hybrid cladding

The shape and microstructure in laser-induction hybrid cladding were investigated, in which the cladding material was provided by means of three different methods including the powder feeding, cold pre-placed coating (CPPC) and thermal pre-placed coating (TPPC). Moreover, the modes of energy action in laser-induction hybrid cladding were also studied. The results indicate that the cladding material supplying method has an important influence on the shape and microstructure of coating. The influence is decided by the mode of energy action in laser-induction hybrid cladding. During the TPPC hybrid cladding of Ni-based alloy, the laser and induction heating are mainly performed on coating. During the CPPC hybrid cladding of Ni-based alloy, the laser and induction heating are mainly performed on coating and substrate surface, respectively. In powder feeding hybrid cladding, a part of laser is absorbed by the powder particles directly, while the other part of laser penetrating powder cloud radiates on the molten pool. Meanwhile, the induction heating is entirely performed on the substrate. In addition, the wetting property on the interface is improved and the metallurgical bond between the coating and substrate is much easier to form. Therefore, the powder feeding laser-induction hybrid cladding has the highest cladding efficiency and the best bond property among three hybrid cladding methods.     

激光熔覆TiC-Ni复合涂层的摩擦磨损性能和磨损机制研究

利用光学显微镜和扫描电镜观察了钛合金表面TiC-Ni激光熔覆层的宏观形貌和微观组织,测试了激光熔覆层的硬度、摩擦系数和磨损量。利用SEM观察了磨损的表面形貌和磨屑的形貌,分析了激光熔覆层的磨损机制。结果表明:激光熔覆层组织致密,无气孔和裂纹,硬度为基材的3倍;激光熔覆层的摩擦系数随环境压力的降低而提高,磨损量随环境压力的降低、法向载荷的增加而增加;低载时为轻微的磨粒磨损,高载时为严重的剥层磨损。     

Microstructure and osteoblast response of gradient bioceramic coating on titanium alloy fabricated by laser cladding

To construct a bioactive interface between metal implant and the surrounding bone tissue, the gradient calcium phosphate bioceramic coating on titanium alloy (Ti-6Al-4V) was designed and fabricated by laser cladding. The results demonstrated that the gradient bioceramic coating was metallurgically bonded to the titanium alloy substrate. The appearance of hydroxyapatite and β-tricalcium phosphate indicated that the bioactive phases were synthesized on the surface of coating. The microhardness gradually decreased from the coating to substrate, which could help stress relaxation between coating and bone tissue. Furthermore, the methyl thiazolyl tetrazolium (MTT) assay of cell proliferation revealed that the laser-cladded bioceramic coating had more favorable osteoblast response compared with the surface of untreated titanium alloy substrate.     

Laser glazing study of Co-based alloy and Ni-Nb-Cr alloy coating

ＬａｓｅｒｇｌａｚｉｎｇｓｔｕｄｙｏｆＣｏ－ｂａｓｅｄａｌｌｏｙａｎｄＮｉ－Ｎｂ－Ｃｒａｌｌｏｙｃｏａｔｉｎｇ￥ＴＩＡＮＮａｉｌｉａｎｇ（ＤｅｐａｒｔｍｅｎｔｏｆＡｐｐｌｉｅｄＰｈｙｓｉｃｓ，ＴｉａｎｊｉｎＩｎｓｔｉｔｕｔｅｏｆＳｃｉｅｎｃｅａｎｄＴ...     

Microstructure and interface interaction in laser induction hybrid cladding of Ni-based coating

Based on the powder feeding laser induction hybrid cladding experiments by means of three different laser and induction energy, the microstructure of Ni-based coating and interface characteristics between the Ni-based coating and steel substrate were investigated. The results show that the hybrid cladding energy including laser and induction energy has an important influence on the formation of the interface and the microstructure of the Ni-based coating characterized by the dendrite. In addition, the laser and induction energy can complement each other. For high hybrid cladding energy, the single phase Fe-Ni-Cr solid solution is formed at the interface between the coating and substrate, while the microhardness of the Ni-based coating decreases. For low hybrid cladding energy, the solid solution phases of Fe-Ni-Cr and Ni-Fe-Cr are respectively obtained on both sides of the interface and microhardness of the Ni-based coating is relatively high. During laser induction hybrid cladding, the metallurgical bond characterized by the white light layer is achieved between the coating and substrate, and the extent of metallurgical reaction can be controlled by adjusting the laser energy and induction energy appropriately.     

Analysis of the interface between a pulsed laser deposited calcium phosphate coating and a titanium alloy substrate

Calcium phosphate coatings deposited on titanium alloy are intended to add a bioactive surface to medical implants. This work presents the characterisation of the interface between Ti-6Al-4V and a crystalline calcium phosphate coating obtained by pulsed laser deposition, with a KrF excimer laser, at 575 °C and under a 45 Pa water-vapour atmosphere. The coating–substrate system was studied by secondary-ion mass spectrometry, scanning electron microscopy, X-ray diffractometry, Raman spectroscopy and X-ray photoelectron spectroscopy. The results show that the deposition process promotes the interdiffusion of substrate elements into the coating and coating elements into the substrate oxide layer. Thus, a graded layer of mixed calcium phosphate and amorphous titanium oxide is formed. For the substrate, a hydroxyapatite coating acts more as a barrier for oxygen incoming from a gas than as an oxygen source during deposition. Moreover, oxygen diffusion into the substrate occurs. Thus, the content of oxygen of this oxide layer diminishes with depth. When the oxygen concentration is low enough it is incorporated in solid solution in the titanium alloy . PACS 81.15.Fg; 68.55.-a; 87.68.+z     

Development and characterization of laser surface cladding (Ti,W)C reinforced Ni–30Cu alloy composite coating on copper

To improve the wear resistance of copper components, laser surface cladding (LSC) was applied to deposit (Ti,W)C reinforced Ni–30Cu alloy composite coating on copper using a cladding interlayer of Ni–30Cu alloy by Nd:YAG laser. The microstructure and phases of the composite coating were investigated by scanning electron microscopy (SEM), X-ray diffraction (XRD) and X-ray energy dispersive microanalysis (EDX). Microhardness tester and pin-on-disc wear tester were employed to evaluate the hardness and dry-sliding wear resistance. The results show that crack-free composite coating with metallurgical bonding to the copper substrate is obtained. Phases identified in the (Ti,W)C-reinforced Ni–30Cu alloy composite layer are composed of TiWC₂ reinforcements and (Ni,Cu) solid solution. TiWC₂ reinforcements are distributed uniformly in the (Ni,Cu) solid solution matrix with dendritic morphology in the upper region and with particles in the mid-lower region. The microhardness and wear properties of the composite coating are improved significantly in comparison to the as-received copper substrate due to the addition of 50 wt% (Ti,W)C multicarbides.     

激光熔覆Al+SiC涂层对镁合金表面耐磨性能的改性

通过脉冲激光器(Nd-YAG)在AZ91D镁合金基底上熔覆Al+SiC粉体。采用扫描电子显微镜、能量色散谱(EDS)和X-射线衍射测定分析熔覆层的显微组织、化学成分和物相组成。研究表明:Al+SiC涂层主要由SiC,β-Mg_(17)Al_(12)及Mg和Al相组成,激光熔覆层与镁合金基底表现出良好的冶金结合。所有样品都具有树枝状结构,且随着SiC质量分数的增大,树枝状和胞状结构的间隔变得更大。熔覆涂层的表面硬度高于基底,并且随着熔覆层中的SiC质量分数的增加而增大,SiC质量分数为40%的熔覆层具有最大的显微硬度,达到180 HV,然而质量分数为10%的熔覆层硬度为136 HV。销盘滑动磨损试验表明,复合涂层中的SiC颗粒和原位合成的Mg_(17)Al_(12)相显著提高了AZ91D镁合金的耐磨损性,其中,SiC质量分数从10%增加到30%过程中磨损体积损失逐渐减少,SiC质量分数在20%~30%时熔覆层具有最好的耐磨性。     

送粉角度对激光熔覆铁基复合涂层形状特征的影响

通过分析激光熔覆过程中光束、粉末和熔池间的作用机理,建立了送粉式激光熔覆材料有效利用率的数学模型,在此基础上推导了送粉角度与工艺参数之间的定量关系式,并计算了不同送粉角度下的熔覆材料有效利用率、熔高和横截面积。结果表明,在熔覆工艺参数不变的条件下,理论计算的熔覆材料有效利用率、熔覆层高度和横截面积均随送粉角度的增加而增大,且均高于实验检测值。激光熔覆过程中,由于粉末烧损和机械损失,使熔覆材料有效利用率、熔高和横截面积随送粉角度变化出现最大值,理想送粉角度为60。     

金属陶瓷复合涂层的激光熔覆与无裂纹的实现

鉴于传统的激光熔覆金属陶瓷复合涂层技术主要存在2方面不足：其一,熔覆效率低,导致大面积熔覆时成本昂贵;其二,由于激光熔覆本身的特点,即快速加热与快速凝固,在激光熔覆过程中,热应力极易诱导熔覆层开裂。基于此,综述了国内外激光熔覆金属陶瓷复合涂层的研究进展,指出其存在的主要问题,并提出了激光感应复合快速熔覆的新方法,即感应预热基材的同时快速激光熔覆。该方法不仅可使熔覆效率大大提高而且获得了无裂纹的金属陶瓷复合涂层。     

Microstructure and properties of 6FeNiCoSiCrAlTi high-entropy alloy coating prepared by laser cladding

The content of each constituent element in the newly developed high-entropy alloys (HEAs) is always restricted in equimolar or near-equimolar ratio in order to avoid the formation of complex brittle phases during the solidification process. In this study, a 6FeNiCoSiCrAlTi high-entropy alloy coating with simple BCC solid solution phase has been prepared by laser cladding on a low carbon steel substrate. The microstructure, hardness and magnetic properties have been investigated. The experimental results show that the tendency of component segregation in the conventional solidification microstructure of multi-component alloy is effectively relieved. The microstructure of the coating is mainly composed of equiaxed polygonal grains, discontinuous interdendritic segregation and nano-precipitates. EBSD observation confirms that the polygonal grains and interdendritic segregation have similar BCC structure with lots of low angle grain boundaries at the interface. The microhardness of the coating reaches 780 HV_0.5, which is much higher than most of the HEAs prepared by other methods. In addition, the coating shows excellent soft magnetic properties.     

铁基合金激光熔覆层的高温磨损性能

 为提高40Cr钢表面耐磨性,采用预置激光熔覆法在40Cr基体表面制备Fe基涂层,利用HT-500摩擦磨损实验机测定干摩擦条件下,基体和熔覆层的摩擦因数随温度变化的规律。利用表面粗糙度轮廓仪测量磨痕的深度和宽度,SEM观察熔覆层以及磨痕的显微组织形貌,使用HV-1000型显微硬度仪检测基体和熔覆层结合部分的硬度。研究结果表明:熔覆层平均显微硬度值达到373.8HV(0.2);显著高于基体硬度198.4HV(0.2)。在干摩擦条件下,随着温度升高,磨损过程逐渐变平缓,平均摩擦因数降低,磨损率增加,耐磨性下降;在350~400 ℃之间,熔覆层磨损性能优于基体。     

光纤布拉格光栅及其应用

近年来新型的紫外激光写入的光纤布拉格光栅元件（ＦＢＧ）以其具有直接写人光纤芯区、插入损耗小、易于全光集成及波长选择性好、传感信息对波长绝对编码等优点,成为国内外光纤技术领域的研究热点。该论文综述了ＦＢＧ制作技术的进展,介绍和比较了各种制作方法的优缺点,对ＦＢＧ在光纤通讯、光纤传感器等方面的应用前景进行了分析和说明,结果表明ＦＢＧ将对整个光纤技术领域产生重要的影响。     

Effects of processing parameters on structure of Ni-based WC composite coatings during laser induction hybrid rapid cladding

The relationships between the processing parameters (i.e. laser specific energy, powder density, preheated temperature of substrate and types of substrate) and the structure characteristics of Ni-based WC composite coatings during laser induction hybrid rapid cladding (LIHRC) were investigated systematically. The results show that laser specific energy, cladding height and contact angle have a linear relation with powder density, as can provide the predictions of laser processing parameters according to the geometrical characteristics of a single laser track (i.e. cladding height, cladding width). Moreover, dilution of composite coating increases with the increasing of laser specific energy and the preheated temperature of substrate, while reduces with the increasing of powder density. The types of substrate also have an important effect on dilution of composite coating, as has a strong dependence on the thermophysical properties of substrate (i.e. melting point, resistivity and permeability).     

铁基合金激光熔覆层高温润滑磨损性能

 为提高40Cr合金钢的表面耐磨性,采用预置激光熔覆法在40Cr基体表面制备铁基合金涂层, 利用扫描电镜观察分析熔覆层显微组织形貌,用显微硬度仪测试熔覆层截面显微硬度,用摩擦磨损试验机测定在润滑条件下基体、熔覆层的摩擦系数随温度变化的规律。研究结果表明:熔覆层与基体实现良好冶金结合,熔覆层横截面微观组织呈现平面晶、树枝晶和胞状晶分布;熔覆层硬度值介于617.5~926.6 HV0.2之间,基体硬度介于205.2~278.2 HV0.2之间;在200 ℃以下,熔覆层摩擦系数在磨程中趋于平稳,在0.1附近轻微波动,小于基体平均摩擦系数;当温度超过200 ℃,油膜分解,引发润滑失效,磨损方式向干摩擦转化,磨损机理从微切削磨损主导向粘着磨损、磨粒磨损和氧化磨损复合磨损方式转化。     

Al、Nd对Cr12MoV钢表面镍基熔覆层的组织及性能影响

为了解决Cr₁₂MoV钢溶蚀、表面碎裂等问题,利用Al-Ni、Nd-Ni粉末在Cr₁₂MoV钢上进行激光熔覆实验,研究了Al、Nd对镍基覆层的宏微观形貌、组织及表面性能的影响。结果表明:Al可以减少熔覆层裂纹的产生,同时降低覆层硬度,使熔覆层中产生具有减磨作用的硬质相Al₂O₃等,降低覆层磨损量,14%Al覆层磨损量比2%Al的覆层磨损量低44.5%,Al较优质量分数为14%;Nd的晶粒细化作用明显,显著提升覆层显微硬度,2.5%Nd覆层平均硬度比基体平均硬度高36.8%,Nd较优质量分数为2.5%。     

Laser induction hybrid rapid cladding of WC particles reinforced NiCrBSi composite coatings

In order to investigate the microstructure characteristics and properties of Ni-based WC composite coatings containing a relatively large amount of WC particles by laser induction hybrid rapid cladding (LIHRC) and compare to the individual laser cladding without preheating, Ni60A + 35 wt.% WC composite coatings are deposited on A3 steel plates by LIHRC and the individual laser cladding without preheating. The composite coating produced by the individual laser cladding without preheating exhibits many cracks and pores, while the smooth composite coating without cracks and pores is obtained by LIHRC. Moreover, the cast WC particles take on the similar dissolution characteristics in Ni60A + 35 wt.% WC composite coatings by LIHRC and the individual laser cladding without preheating. Namely, the completely dissolved WC particles interact with Ni-based alloy solvent to precipitate the blocky and herringbone carbides, while the partially dissolved WC particles still preserve the primary lamellar eutectic structure. A few WC particles are split at the interface of WC and W₂C, and then interact with Ni-based alloy solvent to precipitate the lamellar carbides. Compared with the individual laser cladding without preheating, LIHRC has the relatively lower temperature gradient and the relatively higher laser scanning speed. Therefore, LIHRC can produce the crack-free composite coating with relatively higher microhardness and relatively more homogeneous distribution of WC particles and is successfully applied to strengthen the corrugated roller, showing that LIHRC process has a higher efficiency and good cladding quality.     

Investigation of temperature and stress fields in laser cladded coatings

Temporal and spatial distributions of temperature and strain-stress have been modelled and investigated experimentally for the laser cladding process. The model corresponded to experimental conditions where the multilayer protective coatings were prepared by direct laser cladding of stellite SF6 powder on X10Cr13 chromium steel by means of a 1.2 kW CO₂ laser. For calculations the effect of base preheating, temperature dependent material properties, and also influence of time-break between cladding of the consecutive layers were taken into account. The calculated temperature fields indicated good bonding of the substrate and coating, which was in agreement with the micro-analytical test results. A decrease of the number of microcracks in the coating with an increase of substrate preheating temperature was concluded from stress calculations and confirmed in the experiment. Moreover, an increase of the cracking susceptibility with an increase of the time delay between cladding of the consecutive layers was evidenced by modelling. The best technological results were obtained for the case of single-layer coatings prepared on a preheated substrate and for higher coating thickness required the processing of consecutive layers with a possibly short time delay is advisable due to effective usage of laser beam energy for preheating and lower temperature gradients.