Tunable DBR Lasers Fabricated by Selective Area Growth Technique

The tunable ridge waveguide distributed Brag g reflector (DBR) lasers grown by selective area growth and designed for WDM communication systems at 1.55 μm is reported. The threshold of DBR lasers is 62 mA and the output power is more than 8 mW; the isolation resistance between the active region and Bragg region is 30 kΩ; the tuning range is 6.5 nm which can provide 6 WDM channels with a 100 GHz spacing; in thetuning range, the single mode suppression ratio (SMSR) is more than 32 dB and the output power variation of different wavelengths is less than 3 dB.     

Self-aligned Coupled Waveguide Distributed Bragg Reflector Lasers

A novel self-aligned coupled waveguide (SACW) multi-quantum-well (MQW) distributed Bragg reflector (DBR) laser is proposed and demonstrated for the first time. By selectively removing the MQW layer and leaving the low SCH/SACW layer the Bragg grating is partially formed on this layer. By optimizing the thickness of the low SCH/SACW layer, a-80% coupling efficiency between the MQW gain region and the passive region are obtained. The typical threshold current of the SACW DBR laser is 39 mA, the slope efficiency can reach to 0.2 mW/mA and the output power is more than 20 mW with a more than 30dB side mode suppression ratio.     

Self-aligned Coupled Waveguide Distributed Bragg Reflector Lasers

A novel self-aligned coupled waveguide (SACW) multi-quantum-well (MQW) distributed Bragg reflector (DBR) laser is proposed and demonstrated for the first time. By selectively removing the MQW layer and leaving the low SCH/SACW layer the Bragg grating is partially formed on this layer. By optimizing the thickness of the low SCH/SACW layer, a～80% coupling efficiency between the MQW gain region and the passive region are obtained. The typical threshold current of the SACW DBR laser is 39 mA, the slope efficiency can reach to 0.2 mW/mA and the output power is more than 20 mW with a more than 30dB side mode suppression ratio.     

高功率宽调谐范围掺Yb3+光子晶体光纤激光器

采用闪耀光栅作为色散元件,构建了前向、后向输出两种结构的可调谐掺Yb3 光子晶体光纤激光器,并对其输出特性进行了分析研究.在抽运功率5.75W时,前向输出结构实现了1050.6～1110.2 nm的连续调谐输出,光谱线宽约0.1 nm,边模抑制比大于44 dB.在调谐激光波长为1085 nm时,得到最高输出功率677 mW.结构改进的后向输出结构的可调谐输出结构在抽运功率4.43 W,调谐波长1075 nm,实现了2.21 W的功率输出,斜率效率为73%;调谐范围50.9 nm(1042.1～1093 nm),光谱线宽小于0.08 nm,边模抑制比大于50 dB.两种结构的可调谐激光器输出均为线偏振光,偏振度大于89.5%.     

1.55-μm InGaAs/InGaAlAs MQW vertical-cavity surface-emitting lasers with InGaAlAs/InP distributed Bragg reflectors

High-performance InGaAs/InGaAlAs multiple-quantum-well vertical-cavity surface-emitting lasers (VCSELs) with InGaAlAs/InP distributed Bragg reflectors are proposed for operation at the wavelength of 1.55 μm. The lasers have good heat diffusion characteristic, large index contrast in DBRs, and weak temperature sensitivity. They could be fabricated either by metal-organic chemical vapor deposition (MOCVD) or by molecular beam epitaxy (MBE) growth. The laser light-current characteristics indicate that a suitable reflectivity of the DBR on the light output side in a laser makes its output power increase greatly and its lasing threshold current reduce significantly, and that a small VCSEL could output the power around its maximum for the output mirror at the reflectivity varying in a broader range than a large VCSEL does.     

1.55-μm InGaAs/InGaAlAs MQW vertical-cavity surface-emitting lasers with InGaAlAs/InP distributed Bragg reflectors

High-performance InGaAs/InGaAlAs multiple-quantum-well vertical-cavity surface-emitting lasers (VCSELs) with InGaAlAs/InP distributed Bragg reflectors are proposed for operation at the wavelength of . The lasers have good heat diffusion characteristic, large index contrast in DBRs, and weak temperature sensitivity. They could be fabricated either by metal-organic chemical vapor deposition (MOCVD) or by molecular beam epitaxy (MBE) growth. The laser light-current characteristics indicate that a suitable reflectivity of the DBR on the light output side in a laser makes its output power increase greatly and its lasing threshold current reduce significantly, and that a small VCSEL could output the power around its maximum for the output mirror at the reflectivity varying in a broader range than a large VCSEL does.     

Watt-level red-emitting diode lasers and modules for display applications

Red-emitting lasers for display applications require high output powers and a high visibility. We demonstrate diode lasers and modules in the red spectral range based on AlGaInP with optical output powers up to 1 W and a nearly diffraction limited beam. These high-luminance light sources based on tapered lasers are well suited for laser TVs and projectors for virtual reality simulators based on the flying spot technology. Additionally, we developed diode lasers with internal distributed Bragg reflector (DBR) surface gratings. These DBR tapered lasers and master-oscillator power-amplifiers based on DBR ridge-waveguide lasers and tapered amplifiers feature high power, single mode emission with coherence lengths up to several meters, which are suitable for the next-generation 3D displays based on holography.     

1064nm超短腔DBR单频掺镱硅酸盐光纤激光器

提出了一种基于高掺杂硅酸盐增益光纤、输出波长为1 064nm的超短腔单频光纤激光器.该单频光纤激光器采用分布布拉格反射式腔型结构,有效腔长为2cm,其增益介质为1.1cm长的高浓度掺Yb3+光纤.通过恰当的温度控制,获得了线宽为4.8kHz的稳定单频激光输出.当注入泵浦光为378mW时,输出功率为13mW,斜效率为3.4%.在频率大于1 MHz时,测得该光纤激光器的相对噪声强度值约为-132dB/Hz.采用主振荡功率放大结构,对该单频光纤激光器的输出功率进行放大.当放大增益光纤长度选取为56cm时,得到了325mW的最大输出功率,其斜效率为52.8%.     

Wavelength Tuning in the Two-Section Distributed Bragg Reflector Laser Fabricatedby Quantum-Well Intermixing

The two-section tunable ridge waveguide distributed Bragg reflector (DBR) lasers fabricated by strained InxGa1-xAsyP1-y. The threshold current of the laser is 51mA. The tunable range of the laser is 3.2nm and the side mode suppression ratio (SMSR) is more 38dB.     

Solgel grating waveguides for distributed Bragg reflector lasers

Solgel grating waveguides and their application to the fabrication of external-cavity distributed Bragg reflector (DBR) lasers are demonstrated. A new composition of aluminosilicate material is developed for the fabrication of single-mode waveguides and Bragg reflectors. An average loss of <0.2 dB/cm is measured in the single-mode waveguides at 1550 nm. The reflectors show filtering greater than 97% near 1530 nm, with a bandwidth of ~0.6 nm . The Bragg reflectors are used as feedback resonators for DBR lasers. Single-mode lasing with a sidemode suppression of better than 25 dB is demonstrated.     

Single-frequency, single-polarization ytterbium-doped fiber laser by self-injection locking

We demonstrated a stable single-frequency, single-polarization operation of ytterbium-doped fiber laser. As a novel practical method to realize single-polarization operation of fiber distributed Bragg reflector (DBR)laser, we proposed self-injection locking (SIL) with an active fiber ring feedback cavity. The laser has high output power exceeding 15 mW, wavelength of 1053.20 nm, and side-mode suppression ratio greater than 60 dB. The SIL fiber laser shows the improvements in output power and side-mode suppression compared with the fiber DBR laser. No mode-hopping is observed within 2 hours.     

互注入锁定产生双波长可调谐光脉冲的实验研究

报道了两个增益开关调制的法布里-珀罗半导体激光器互注入锁定实验方案,可产生双波长可调谐光脉冲。该装置对两个结构基本相同的法布里珀罗半导体激光器做增益开关调制,产生多模光脉冲输出;然后利用两个光纤光栅作为滤波元件,通过调节可调谐光延迟线(VODL2),可使得双波长光脉冲在两个法布里-珀罗激光器之间相互注入锁定．从而在输出端得到高边模抑制比的双波长光脉冲输出。然后再通过应力作用在两个光纤光栅上以改变它们的反射波长和适当调整另一个可调谐光延迟线(VODLI)长度．可得到不同的双波长的光脉冲输出,而重复频率保持524．6MHz不变。在13．2nm调谐范围内边模抑制比高于25dB．系统稳定且波长调节方便。     

均衡功率的超宽带可调谐掺铒光纤激光器

报道了一种功率均衡的超宽带可调谐掺铒光纤激光器.该激光器采用窄线宽可调谐FP滤波器、掺铒光纤、波分复用器和耦合器构成光纤环形腔激光器，并通过部分反馈光功率自动控制，对输出激光功率进行均衡.实现了87 nm带宽（1525~1612 nm）范围内，输出激光功率波动小于0.2 dB的均衡结果.输出激光3 dB线宽为0.26 nm，边模抑制比大于55 dB.     

Wideband wavelength tunable fiber ring laser with flattened output power spectrum

A wavelength tunable erbium-doped fiber ring laser with flattened output power spectrum over a broadband is proposed and demonstrated. The power flattening is achieved using a high-birefringence fiber loop mirror, in which a number of high-birefringence fiber sections and polarization controllers are used to get a reflection spectrum that can compensate for the output power spectrum. The wavelength tuning is realized by compressing or stretching the FBGs in the laser cavity. A 1×3 switchable fiber Bragg grating array is incorporated into the fiber ring to get a wideband tuning range of 38 nm, from 1527 to 1565 nm. Within this range, the output power uniformity is controlled within ±0.8 dB. The total output power is about 4 dBm, the 3-dB linewidth is 0.01 nm, and the side mode suppression ratio is more than 48 dB.     

Numerical analysis and experimental results of output performance for Nd-doped double-clad fiber lasers

Numerical analysis is investigated for the high-power double-clad fiber lasers and experimental results using different microscope objectives for focusing into a Nd-doped rectangular double-clad fiber also performed. The numerical analysis includes dependence of output power on output mirror reflectivity, absorbed pump power, loss, and fiber length and pump power distribution for the cases of one-end and two-end pumps with 20 dB/km loss. Calculated conversion efficiencies are 76.36%, 69.73%, and 63.84% for lossless, two-end pump, and one-end pump fiber lasers, respectively. Slope efficiencies from absorbed pump power/output powers measured using microscope objectives are 16.8%/182 mW, 53.8%/351 mW, 24.9%/1240 mW, and 13.9%/649 mW for magnifications of 5×, 10×, 20×, and 40×, respectively.     

The simulation of self-mixing interference effects in three-section DBR lasers

The self-mixing interference in three-section distributed Bragg reflector (DBR) lasers is analyzed based on the model of F-P cavity and coupling wave equation. The oscillating frequency and threshold variation are deduced. The influence of internal and external parameters on the output intensity and the inclination degree of waveform are discussed in simulation.     

Characterization of a dual wavelength fibre laser based-on dumbbell configuration

This paper reports the design of a dual wavelength fibre laser system using a dumbbell shaped configuration. The oscillation of the lasing wavelength is completed via fibre loop mirrors with a tuneable bandpass filter. The output power, side mode suppression ratio and wavelength spacing of the lasers were investigated against the pump power for forward and backward pumping schemes. The output powers of 4.99 and 3.69 dBm at 1545.08 and 1547.28 nm, respectively, for forward pumping scheme. On contrary, the output powers of 1.93 and 2.14 dBm at 1546.12 and 1551.48 nm, respectively, for backward pumping scheme. The peak output powers of less than 1 dB difference are obtained without any adjustment of the intra-cavity loss over a wider spectral range.     

Design of a monolithic tunable laser based on equivalent-chirp grating reflectors

A Vernier-tuned distributed Bragg reflector (DBR) semiconductor laser is an effective monolithic approach for wide wavelength tunability, at the expense, however, of costly electron-beam lithography during fabrication. In this Letter, a tunable laser design with equivalent-chirp based, flat-top envelope grating reflectors is proposed that can be implemented easily by conventional two-beam interference lithography. The principle is described, and a detailed design shows uniform output power (0.08 dB variation) and excellent side-mode suppression ratio (47 dB minimum) within a wide tuning range (>32 nm) through numerical simulation.     

HR-coated facet effect on the spectral characteristics of a three-section DBR tunable laser

High-relfection (HR)-coated facet effects on the spectral characteristics of a three-section distributed Bragg reflector (DBR) tunable laser are investigated theoretically, in which the output power emits to the DBR section. It is found that the output power to the DBR sectionP _DBR compared to the cleaved facet output powerP ₀ is nearly constant to some degree with increasing tuning current. Owing to the high-Q resonator, the HR-coated DBR laser showed a decrease in spectral linewidth. However, there is still linewidth broadening of the HR-coated DBR laser even though the rate of increase is smaller than that of the cleaved-facet DBR laser. In the case of output power emission to the DBR section, it is thought that the HR-coated effect can overcome the decrease in output power under frequency tuning, which is one of the most important drawbacks of DBR laser performance.     

大功率半导体激光器的可靠性研究

对InGaAs/AlGaAs和InGaAsP/GaAs有源区含铝的915nm和无铝的808nm腔面镀膜及未镀膜的大功率半导体激光器进行了老化实验。在老化前通过综合参数测试仪测试两种激光器的斜率效率、阈值电流，发现有腔面膜的激光器比无腔面膜的激光器的阈值电流降低25％以上。在1.2倍阈值电流下，恒流老化40h左右，老化后再分别测试它们的阈值电流、功率参数，我们发现在老化后未镀膜的激光器的阈值电流和镀有腔面膜的激光器相比增加25mA以上，输出功率也比镀过腔面膜的减小到了原来的1／2，可见腔面保护对于延长激光器的寿命是很重要的。