烟草各部位中茄尼醇含量分布研究

采用Kromsil ODS-1色谱柱,V(甲醇)∶V(乙醇)=55∶45混合液为流动相,在紫外检测波长设定为211 nm的高效液相色谱条件下测定了烟草中各部位提取物中的茄尼醇,其中烟叶中茄尼醇的质量分数为0.45%,其他部位茄尼醇的质量分数为:烟梗0.037%,烟茎0.0037%,烟根0.0037%,其中烟叶中的茄尼醇量最高,具有提取价值.     

液相色谱-大气压化学电离离子阱质谱法测定烟草中的游离茄尼醇

用液相色谱/大气压化学电离离子阱质谱建立了一种分析烟草中游离茄尼醇的方法。烟草样品用甲醇振荡提取30 min,在分析前无需进行其它前处理。在1.8μm快速分离C18色谱短柱上用V(甲醇)∶V(异丙醇)=85∶15等梯度洗脱实现了茄尼醇的快速分离。用不带碰撞能量的二级质谱全扫描选择监测离子m/z 613.6进行定量,检出限为0.4μg/L,RSD为1.1%,两种添加量的回收率分别为97%和99%。方法应用于不同烟草和烟草制品样品的检测分析。     

土豆叶中茄尼醇的高速逆流色谱法分离纯化及质谱解析

采用超微回流提取方法提取土豆叶中的茄尼醇,用高速逆流色谱(HSCCC)对粗提物中的茄尼醇进行分离纯化。以正己烷-甲醇(体积比为10∶7)作为两相溶剂系统,以其下相为流动相,上相为固定相,经过一步HSCCC从60 mg茄尼醇粗提物中分离得到了5 mg 纯度为98.7%的茄尼醇;对分离得到的茄尼醇进行大气压化学电离质谱解析,研究了茄尼醇的大气压化学电离质谱的一级电离规律和二级质谱裂解规律。     

高效液相色谱法测定烟叶提取物中茄尼醇的含量

 采用硅胶色谱柱 ,以正己烷 异丙醇 (体积比为 98∶2 )混合液为流动相 ,在紫外检测波长设定为 2 15nm的高效液相色谱仪上测定了烟叶提取物中茄尼醇的含量。实验结果表明 :方法在茄尼醇进样量为 1μg～ 10 μg时有良好线性关系 (Y =16 6 2 0 4X - 32 5 3,r=0 9997) ;加标回收实验 (n =6 )的平均回收率为 98 1% ,RSD为 1 9% ;方法简便 ,有良好的精密度和准确性。     

液相色谱-大气压化学电离质谱法分析人参中的人参皂甙

研究了用反相高效液相色谱-大气压化学电离质谱(HPLC/APCI-MS)分析人参皂甙的方法。液相色谱采用乙腈-水流动相进行梯度洗脱,质谱采用正负离子同时扫描并结合二级质谱进行定性,用选择反应离子模式(SRM)测定检测限。实验发现虽然人参皂甙是热不稳定物质,但在大气压化学电离质谱的高温汽化过程中仍能检测到很强的负离子分子离子峰,而且随着汽化温度的升高,人参皂甙的负离子分子离子峰的强度增加。该方法对人参皂甙Rb1和Rg1的检测限分别为1.2×10-13 g和3.0×10-14 g,并检测出白参中包括丙二酰人参皂甙在内的29种人参皂甙。该法灵敏度高,重复性好,结果准确,能有效地对药材提取物中的多种人参皂甙进行检测和结构分析。     

Capillary liquid chromatography-microchip atmospheric pressure chemical ionization-mass spectrometry

A miniaturized nebulizer chip for capillary liquid chromatography-atmospheric pressure chemical ionization-mass spectrometry (capillary LC-microchip APCI-MS) is presented. The APCI chip consists of two wafers, a silicon wafer and a Pyrex glass wafer. The silicon wafer has a DRIE etched through-wafer nebulizer gas inlet, an edge capillary insertion channel, a stopper, a vaporizer channel and a nozzle. The platinum heater electrode and pads for electrical connection were patterned on to the Pyrex glass wafer. The two wafers were joined by anodic bonding, creating a microchip version of an APCI-source. The sample inlet capillary from an LC column is directly connected to the vaporizer channel of the APCI chip. The etched nozzle in the microchip forms a narrow sample plume, which is ionized by an external corona needle, and the formed ions are analyzed by a mass spectrometer. The nebulizer chip enables for the first time the use of low flow rate separation techniques with APCI-MS. The performance of capillary LC-microchip APCI-MS was tested with selected neurosteroids. The capillary LC-microchip APCI-MS provides quantitative repeatability and good linearity. The limits of detection (LOD) with a signal-to-noise ratio (S/N) of 3 in MS/MS mode for the selected neurosteroids were 20-1000 fmol (10-500 nmol l(-1)). LODs (S/N = 3) with commercial macro APCI with the same compounds using the same MS were about 10 times higher. Fast heat transfer allows the use of the optimized temperature for each compound during an LC run. The microchip APCI-source provides a convenient and easy method to combine capillary LC to any API-MS equipped with an APCI source. The advantages and potentials of the microchip APCI also make it a very attractive interface in microfluidic APCI-MS.     

Determination of rice herbicides, their transformation products and clofibric acid using on-line solid-phase extraction followed by liquid chromatography with diode array and atmospheric pressure chemical ionization mass spectrometric detection

A simultaneous method for the trace determination of acidic, neutral herbicides and their transformation products in estuarine waters has been developed through an on-line solid-phase extraction method followed by liquid chromatography with diode array and mass spectrometric detection. An atmospheric pressure chemical ionization (APCI) interface was used in the negative ionization mode after optimization of the main APCI parameters. Limits of detection ranged from 0.1 to 0.02 ng/ml for 50 ml of acidified estuarine waters preconcentrated into polymeric precolumns and using time-scheduled selected ion monitoring mode. Two degradation products of the acidic herbicides (4-chloro-2-methylphenol and 2,4-dichlorophenol) did not show good signal response using APCI-MS at the concentration studied due to the higher fragmentor voltage needed for their determination. For molinate and the major degradation product of propanil, 3,4-dichloroaniline, positive ion mode was needed for APCI-MS detection. The proposed method was applied to the determination of herbicides in drainage waters from rice fields of the Delta del Ebro (Spain). During the 3-month monitoring of the herbicides, 8-hydroxybentazone and 4-chloro-2-methylphenoxyacetic acid were successively found in those samples.     

Determination of nivalenol and deoxynivalenol in wheat using liquid chromatography-mass spectrometry with negative ion atmospheric pressure chemical ionisation.

A new, rapid and sensitive method has been developed for the determination of nivalenol (NIV) and deoxynivalenol (DON) by using HPLC in combination with an atmospheric pressure chemical ionization (APCI)-interface and a single quadrupole mass spectrometer. Different LC and MS parameters have been optimized prior to this in order to obtain better results and sensitivity. The effect of nebulizing temperature on the sensitivity and fragmentation of NIV and DON in an APCI interface was investigated. Also, the influence of the cone voltage on the fragmentation pattern was studied, which was shown to have a tremendous effect. Furthermore, the effect of modifiers such as ammonium acetate, acetic acid and ammonia on the ionisation yield of the above substances have been investigated. The extraction was carried out using acetonitrile-water. A two step purification was then applied on two different Mycosep clean up columns. We have used a modified, rapid and isocratic HPLC method combined with a negative ion APCI-MS for the separation and quantitative determination of NIV and DON in wheat extract. An RP C18 column was used for the separation of selected compounds in wheat extract with water-acetonitrile-methanol (82:9:9, v/v/v) at a flow-rate of 1 ml/min without a split. Calibration curves show good linearity and reproducibility. The detection limit and precision were determined for NIV and DON. Both compounds could be detected down to microg/kg level in wheat using selected ion monitoring of the [M-H]- ions and the main fragments.     

Quantitation of triacylglycerols in plant oils using HPLC with APCI-MS, evaporative light-scattering, and UV detection

The main constituents of plant oils are complex mixtures of TGs differing in acyl chain lengths, number and positions of double bonds, and regioisomerism. A non-aqueous reversed-phase HPLC method with acetonitrile-2-propanol gradient and 30 + 15 cm NovaPak C18 columns makes possible an unambiguous identification of the highest number of TGs ever reported for these oils, based on positive-ion APCI mass spectra. A new approach to TG quantitation is based on the use of response factors with three typical detection techniques for that purpose (APCI-MS, evaporative light-scattering detection, and UV at 205 nm). Response factors of 23 single-acid TGs (saturated TGs from C7 to C22, 7 unsaturated TGs), 4 mixed-acid TGs, diolein and monoolein are calculated from their calibration curves and related to OOO. Due to differences between saturated and unsaturated acyl chains, the use of response factors significantly improves the quantitation of TGs. 133 TGs containing 22 fatty acids with 8-25 carbon atoms and 0-3 double bonds are identified and quantified in 9 plant oils (walnut, hazelnut, cashew nut, almond, poppy seed, yellow melon, mango, fig, date) using HPLC/APCI-MS with a response factor approach. Average parameters and relative fatty acid concentrations are calculated with both HPLC/APCI-MS and GC/ FID.     

Comparison of atmospheric pressure chemical ionization and electrospray ionization mass spectrometry for the detection of lignans from sesame seeds

In sesame seeds, high concentrations of lignans are present. When these lignans are fermented in the human colon, a range of structurally different lignans is formed. A good liquid chromatography/mass spectrometry (LC/MS) protocol for the analysis of lignans in complex mixtures is lacking. In order to develop such a protocol, electrospray ionization (ESI)-MS and atmospheric pressure chemical ionization (APCI)-MS, both in the positive and negative ionization mode, were compared. An extract from defatted sesame meal was analyzed by APCI-MS and ESI-MS, before and after deglucosylation. APCI-MS was found to be a more generic method than ESI-MS because lignans, especially sesamolin, sesamin and pinoresinol, were better detected by APCI-MS than by ESI-MS. Positive and negative ionization modes had to be combined in order to detect all lignans in a bacterial culture grown on aglyconic, acid-treated lignans from sesame oil and defatted sesame meal. Lignans with methylenedioxy-bridged furanofuran structures mostly lack phenolic hydroxyl groups and were, therefore, optimally detected in positive ionization mode. Dibenzylbutadiene lignans, which were formed during fermentation, carry hydroxyl groups and were better detected in negative ionization mode.     

An HPLC method for the quantification of sterols in edible seaweeds

This study presents an HPLC method for the quantification of sterols in edible seaweeds. Sterols were identified by HPLC/mass spectrometry (HPLC-MS) in positive APCI mode. The samples were saponified by refluxing with 1 m ethanolic KOH, and the non-saponifiable fraction was extracted with hexane. Sterols were quantified by HPLC with UV detection (HPLC-UV), on a 15 x 0.4 cm Kromasil 100 C(18) 5 micro m column (mobile phase 30:70 v/v methanol:acetonitrile; fl ow rate 1.2 mL/min; column temperature 30 degrees C; detection wavelength 205 nm). Method repeatability for fucosterol was good (coefficient of variation 2.4%). Sterol contents were determined in canned or dried brown seaweeds (Himanthalia elongata, Undaria pinnatifida, Laminaria ochroleuca) and red seaweeds (Palmaria sp., Porphyra sp.). The predominant sterol was fucosterol in brown seaweeds (83-97% of total sterol content; 662-2320 micro g/g dry weight), and desmosterol in red seaweeds (87-93% of total sterol content; 187-337 micro g/g dry weight).     

Detection of 6-(methylsulfinyl)hexyl isothiocyanate (6-MITC) and its conjugate with N-acetyl-L-cysteine (NAC) by high performance liquid chromatograpy-atmospheric pressure chemical ionization mass spectrometry (HPLC-MS/APCI)

A method using high-performance liquid chromatography (HPLC) and atmospheric pressure chemical ionization (APCI) mass spectrometry (MS) was established for the detection of 6-(methylsulfinyl)hexyl isothiocyanate (6-MITC) and its conjugate with N-acetyl-L-cysteine (NAC). The optimal chromatographic conditions were obtained on an ODS column (150 x 4.6 mm, 3 microm) with the column temperature at 37 degrees C. The mobile phase consisted of a methanol-0.1% trifluoroacetic acid (TFA) mixture (50 : 50, v/v), and the flow rate was 0.3 ml/min. The detection wavelength was set at 220 nm. The identities of the peaks were accomplished by comparing retention times (tR), UV and mass data. All calibration curves showed good linear regression (correlation coefficients for 6-MITC and NAC>0.999) within test ranges. The developed method provided satisfactory precision calculated as percent coefficient of variation with overall intra-day and inter-day variations of less than 5% (4.1 and 4.9% for 6-MITC; 4.2 and 4.9% for NAC). Both 6-MITC and NAC had good responses in the positive APCI and formed strong [M+H]+ ions in the full scan spectra at an m/z of 206 and 164, respectively. The presence of the [M+H]+ ion for the 6-MITC/NAC conjugate was also observed at an m/z of 369. To our best knowledge, this is the first report that describes the formation of the 6-MITC/NAC conjugate and its detection method by HPLC-MS.     

Comparison of reversed-phase liquid chromatography-mass spectrometry with electrospray and atmospheric pressure chemical ionization for analysis of dietary tocopherols

ESI and APCI ionization techniques in both negative and positive ion modes were evaluated for simultaneous LC-MS analysis of the four tocopherol homologues (alpha, beta, gamma and delta). The ESI and APCI ionization of tocopherols in positive ion mode was not efficient and proceeded via two competitive mechanisms, with the formation of protonated pseudo-molecular ions and molecular ions, which adversely influenced the repeatability of MS signal. Ionization in negative ion mode in both ESI and APCI was more efficient as it only produced target deprotonated pseudo-molecular ions. The APCI in negative ion mode showed larger linearity range, lower detection limits and was less sensitive to the differences in chemical structure of analytes and nature of applied solvents than negative ion ESI. Negative ion APCI was, therefore, chosen for the development of LC-MS method for simultaneous determination of the four tocopherols in foods. A baseline separation of the tocopherols was achieved on novel pentafluorophenyl silica-based column Fluophase PFP. The use of methanol-water (95:5, v/v) as a mobile phase was preferable to the use of acetonitrile-water due to considerable gain in MS signal. The limits of quantifications were 9 ng/mL for alpha-tocopherol, 8 ng/mL for beta- and gamma- and 7.5 ng/mL for delta-tocopherol when 2 microL was injected. This method was successfully applied to determination of tocopherols in sunflower oil and milk.     

Development and validation of reversed-phase column high-performance liquid chromatographic and first-derivative UV spectrophotometric methods for estimation of voriconazole in oral suspension powder

This research paper describes validated reversed-phase high-performance column liquid chromatographic (RP-HPLC) and first-derivative UV spectrophotometric methods for the estimation of voriconazole (VOR) in oral suspension powder. The RP-HPLC separation was achieved on Phenomenex C18 column (250 x 4.6 mm id, 5 microm particle size) using water-acetonitrile (40 + 60, v/v; pH adjusted to 4.5 +/- 0.02 with acetic acid) as the mobile phase at a flow rate of 1.4 mL/min and ambient temperature. Quantification was achieved with photodiode array detection at 255 nm over the concentration range of 0.1-1 microg/mL with mean recovery of 99.49 +/- 0.83% for VOR by the RP-HPLC method. Quantification was achieved with UV detection at 266 nm over the concentration range of 8-20 microg/mL with mean recovery of 99.74 +/- 0.664% for VOR by the first-derivative UV spectrophotometric method. These methods are simple, precise, and sensitive, and they are applicable for the determination of VOR in oral suspension powder.     

Simultaneous estimation of acetylsalicylic acid and clopidogrel bisulfate in pure powder and tablet formulations by high-performance column liquid chromatography and high-performance thin-layer chromatography

This paper describes validated high-performance column liquid chromatographic (HPLC) and high-performance thin-layer chromatographic (HPTLC) methods for simultaneous estimation of acetylsalicylic acid (ASA) and clopidogrel bisulfate (CLP) in pure powder and formulations. The HPLC separation was achieved on a Nucleosil C8 column (150 mm length x 4.6 mm id, 5 microm particle size) using acetonitrile-phosphate buffer, pH 3.0 (55 + 45, v/v) mobile phase at a flow rate of 1.0 mL/min at ambient temperature. The HPTLC separation was achieved on an aluminum-backed layer of silica gel 60F254 using ethyl acetate-methanol-toluene-glacial acetic acid (5.0 + 1.0 + 4.0 + 0.1, v/v/v/v) mobile phase. Quantitation was achieved with UV detection at 235 nm over the concentration range 4-24 microg/mL for both drugs, with mean recoveries of 99.98 +/- 0.28 and 100.16 +/- 0.66% for ASA and CLP, respectively, using the HPLC method. Quantitation was achieved with UV detection at 235 nm over the concentration range of 400-1400 ng/spot for both drugs, with mean recoveries of 99.93 +/- 0.55 and 100.21 +/- 0.83% for ASA and CLP, respectively, using the HPTLC method. These methods are simple, precise, and sensitive, and they are applicable for the simultaneous determination of ASA and CLP in pure powder and formulations.     

High-performance liquid chromatography/atmospheric pressure chemical ionization tandem mass spectrometry determination of cholesterol uptake by Caco-2 cells

A simple, sensitive and selective liquid chromatography/atmospheric pressure chemical ionization tandem mass spectrometric method (LC/APCI-MS/MS) was developed and applied to quantitative determination of uptake of cholesterol by Caco-2 human intestine cells. Caco-2 cells were cultured in medium containing cholesterol-3,4-13C2 and phytosterols from nutritional supplements after in vitro digestion. Cellular cholesterol (cholesterol-3,4-13C2) and endogenous cholesterol were extracted using methanol/chloroform (1:2, v/v) and directly analyzed using LC/APCI-MS/MS with selected reaction monitoring (SRM), using cholesterol-2,2,3,4,4,6-d6 as an internal standard. Detection and quantification limits were 2.2 and 7.2 pmol, respectively. This method provides an effective tool for rapid determination of cholesterol uptake by cells with increased selectivity and sensitivity in comparison to previously reported LC/APCI-MS analysis using selected ion monitoring (SIM).     

Characterization of prenylflavonoids and hop bitter acids in various classes of Czech beers and hop extracts using high-performance liquid chromatography–mass spectrometry

Hops contain a wide range of polyphenolic compounds with antioxidant properties divided in various chemical classes. These compounds are detected in hop extracts and also in beer as its main product. Based on the careful optimization of column type, column packing, mobile phase composition and gradient steepness, two high-performance liquid chromatography–mass spectrometry (HPLC/MS) methods have been developed. The first method using Purospher Star RP-8e column and the gradient of aqueous acetonitrile containing 0.3% formic acid is optimized for the separation of low polar polyphenolic compounds, while the second one with Zorbax SB-CN column is used for more polar hops and beer components. In this work, more compounds are detected in comparison to previous reports. In total, 49 low polar and 37 polar compounds are detected in studied samples and their molecular weights are determined based on atmospheric pressure chemical ionization (APCI) mass spectra. Some compounds are identified based on the interpretation of their full scan and tandem APCI mass spectra, retention behavior and UV spectra, while the full structure elucidation of other species still requires further research. The quantitation of xanthohumol related prenylflavonoids and bitter acids is done with two detection techniques (APCI-MS and UV detection) providing comparable results. Both compound classes (i.e., prenylflavonoids and bitter acids) are separated and quantitated in a single HPLC run, where numerous other polyphenolics are detected as well.     

Simultaneous estimation of pantoprazole and domperidone in pure powder and a pharmaceutical formulation by high-perfomance liquid chromatography and high-performance thin-layer chromatography methods

This paper describes validated high-performance liquid chromatography (HPLC) and high-performance thin-layer chromatography (HPTLC) methods for the simultaneous estimation of pantoprazole (PANT) and domperidone (DOM) in pure powder and capsule formulations. The HPLC separation was achieved on a Phenomenex C18 column (250 mm id, 4.6 mm, 5 pm) using 0.01 M, 6.5 pH ammonium acetate buffer-methanol-acetonitrile (30 + 40 + 30, v/v/v, pH 7.20) as the mobile phase at a flow rate of 1.0 mL/min at ambient temperature. The HPTLC separation was achieved on an aluminum-backed layer of silica gel 60F254 using ethyl acetate-methanol (60 + 40, v/v) as the mobile phase. Quantification was achieved with ultraviolet (UV) detection at 287 nm over the concentration range 400-4000 and 300-3000 ng/mL with mean recovery of 99.35+/-0.80 and 99.08+/-0.57% for PANT and DOM, respectively (HPLC method). Quantification was achieved with UV detection at 287 nm over the concentration range 80-240 and 60-180 ng/spot with mean recovery of 98.40+/-0.67 and 98.75+/-0.71% for PANT and DOM, respectively (HPTLC method). These methods are simple, precise, and sensitive, and they are applicable for the simultaneous determination of PANT and DOM in pure powder and capsule formulations.     

Capillary electrophoretic determination of phosphate based on the formation of a Keggin-type [PMo12O40]3- complex.

Based on the formation of a Keggin-type [PMo12O40]3- complex, a sensitive capillary electrophoresis (CE) method was developed for the determination of P(V) with direct UV detection at 220 nm. A mixture of alpha- and beta-Keggin-type [PMo12O40]3- complexes was readily formed in a sample solution consisting of a trace amount of P(V), 2.5 mM Mo(VI), 0.050 M p-C6H3(CH3)-2-SO3H (XSA), and 60% v/v CH3CN. When a 0.05 M HCl and 60% v/v CH3CN solution was used as a migration electrolyte, the Keggin complexes exhibited a sharp and well-defined peak in the electropherogram. The peak area was linearly dependent on the P(V) concentration in the range of 5 x 10(-7)-5 x 10(-5) M; a detection limit of 1 x 10(-7) M was achieved. In comparison with indirect UV detection, the direct UV detection is about ten times more sensitive, because the Keggin complexes possess high molar absorptivities. The developed CE method was applied to the determination of P(V) in river water, and the results were in good agreement with those obtained by ion chromatography (IC) and colorimetry (COL) based on the formation of mixed-valence heteropoly blue species.     

Rapid determination of haloperidol and its metabolites in human plasma by HPLC using monolithic silica column and solid-phase extraction

A rapid, sensitive and reproducible HPLC method was developed and validated for the analysis of haloperidol and its three main metabolites in human plasma. The analysis was carried out on a monolithic silica column (Chromolith Performance RP-18e, 100 x 4.6 mm). The mobile phase consisted of sodium phosphate (0.1 m, pH 3.5)-acetonitrile (80:20, v/v) at a flow rate of 2.0 mL/min. UV detection at 230 nm was used, with the detection limits of these compounds ranging from 2 to 5 ng. The separation factors of all studied compounds were in the range 2.30-16.32, while the resolution factors were from 1.00 to 5.37.