Growth and characterization of ferromagnetic shape memory alloy Co50Ni20FeGa29 single crystals

Single crystals of Co₅₀Ni₂₀FeGa₂₉ with B2 phase have been obtained in a deep supercooling condition. The interface-facets and the segregation effect lead to the formation of ordered defects that store a directional internal stress. These defects give to a large energy barrier that leads to a very sharp martensitic transformation within a temperature window of only 2 K. The single crystals show good shape memory effect and superelasticity, which are anisotropic between the growth direction [0 0 1] and its equivalent direction [0 1 0]. The anisotropic behaviors are attributed to the directional internal stress caused by the ordered defects.     

Growth and properties of Pb[(Zn1/3Nb2/3)0.91Ti0.09]O3 single crystals directly from melt

Pb[(Zn_1/3Nb_2/3)_0.91Ti_0.09]O₃ (PZNT91/9) single crystals were grown by a modified Bridgman method directly from melt using an allomeric Pb[(Mg_1/3Nb_2/3)_0.69Ti_0.31]O₃ (PMNT69/31) single crystal as a seed. X-ray diffraction (XRD) measurement confirmed that the as-grown PZNT91/9 single crystals are of pure perovskite structure. Electrical properties and thermal stabilization of PZNT91/9 crystals grown directly from melt exhibit different characters from those of PZNT91/9 crystals grown from flux, although segregation and the variation of chemical composition are not seriously confirmed by X-ray fluorescence analysis (XPS). The [0 0 1]-oriented PZNT91/9 crystals cut from the middle part of the as-grown crystal boules exhibit broad dielectric-response peaks at around 105 °C, accompanied by apparent frequency dispersion. The values of piezoelectric constant d₃₃, remnant polarization P_r, and induced strain are about 1800–2200 pC/N, 38.8 μC/cm², and 0.3%, respectively, indicating that the quality of PZNT crystals grown directly from melt can be comparable to those of PZNT91/9 single crystals grown from flux. However, further work deserves attention to improve the dielectric properties of PZNT crystals grown directly from melt. Such unusual characterizations of dielectric properties of PZNT crystals grown directly from melt are considered as correlating with defects, microinhomogeneities, and polar regions.     

Growth, refined structural and spectroscopic characteristics of Tm-doped NaGd(WO4)2 single crystals

The details of Tm³⁺-doped NaGd(WO₄)₂ single-crystal growth are discussed, the results of precise investigations of its structural and spectroscopic characteristics, as well as the analysis of cross-relaxation process of Tm³⁺ ions (³H₄→³F₄, ³H₆→³F₄) in this crystal are presented. Based on the Judd–Ofelt theory, three intensity parameters, spontaneous emission probabilities, fluorescence branching ratios and fluorescence quantum efficiency from ³H₄ and ³F₄ levels were refined.     

Growth, thermal and spectral properties of Nd-doped NaGd(MoO4)2 crystal

Nd³⁺-doped NaGd(MoO₄)₂ crystal with dimensions were grown by Czochralski method. Nd³⁺:NaGd(MoO₄)₂ crystal melts at 1182 °C. The hardness of Nd³⁺:NaGd(MoO₄)₂ crystal is 334 VDH. The specific heat is 72.6 cal/mol K. The thermal expansion coefficients are for c-axis and for a-axis, respectively. The absorption cross-sections of Nd³⁺:NaGd(MoO₄)₂ crystal are with a FWHM of 9 nm at the 804 nm for π-polarization and with a FWHM of 17 nm at 807 nm for σ-polarization, respectively. The emission cross-section σ_em are at 1063 nm for π-polarization and 1.94×10^-20 at 1070 nm cm² for σ-polarization, respectively. The fluorescence lifetime τ_f is 93.9 μs at room temperature.     

Growth and scintillation properties of the Na2W2O7 crystal

The growth and scintillation properties of the Na₂W₂O₇ crystal are reported. The solid reaction between Na₂CO₃ and WO₃ is used to synthesise the Na₂W₂O₇ material. The Na₂W₂O₇ single crystal has been grown by the Bridgman method. And the Na₂W₂O₇ single crystal with sizes 14×7×6 mm³ has been achieved. The transmission spectra, the Ultraviolet fluorescence spectra and the X-ray excited luminescence spectra of the Na₂W₂O₇ crystal are measured. The measurement results show that the Na₂W₂O₇ crystal is a promising intrinsic scintillator.     

Flux growth of PbMg1/3Ta2/3O3 single crystals

Single crystals of PbMg_1/3Ta_2/3O₃ (PMT) were grown by the flux method. The PbO–Pb₃O₄–B₂O₃ system was used as a solvent. Transparent and light yellow PMT single crystals of rectangular shape and dimensions up to 10×6×4 mm³ were obtained. For the applied growth conditions only, the crystals of the perovskite structure were grown. X-ray diffraction tests showed that at room temperature PMT exhibits cubic symmetry with lattice parameter a=4.042(1) Å. Dielectric studies pointed to relaxor properties of PMT. The characteristic broad and frequency-dependent maximum of dielectric permittivity was observed at 179.7 K (1 kHz).     

The growth and spectroscopic characteristics of Ca3Y2(BO3)4:Er laser crystal

The Ca₃Y₂(BO₃)₄:Er³⁺ crystal with a size up to 20 mm×30 mm was grown by the Czochralski method. The absorption spectrum was measured and its absorption peaks were assigned to the corresponding transitions between the Er³⁺ energy levels. A broad emission spectrum from 1429.4 to 1662.8 nm was exhibited from 530 nm wavelength pumping. This crystal is promising as a tunable infrared laser crystal.     

Ambient-condition growth of superconducting YBa2Cu4O8 single crystals using KOH flux

YBa₂Cu₄O₈ is a stoichiometric oxide superconductor of T_c80 K. Unlike YBa₂Cu₃O_7−δ, this compound is free from oxygen vacancy or twin formation and does not have any microscopic disorder in the crystal. Doping with Ca raises its T_c to 90 K. The compound is a promising superconductor for technological application. Up to now, single crystals have not been grown without using specialized apparatus with extremely high oxygen pressure up to 3000 bar and at over 1100 °C due to the limited range of reaction kinetics of the compound. This fact has delayed the progress in the study of its physical properties and potential applications. We present here a simple growth method using KOH as flux that acts effectively for obtaining high-quality single crystals in air/oxygen at the temperature as low as 550 °C. As-grown crystals can readily be separated from the flux and exhibit a perfect orthorhombic morphology with sizes up to 0.7×0.4×0.2 mm³. Our results are reproducible and suggest that the crystals can be grown using a conventional flux method under ambient condition.     

Growth and spectroscopic characterization of Zr:Fe:LiNbO3 crystals with various Li/Nb ratios

In this paper, Zr:Fe:LiNbO₃ crystals with various Li/Nb ratios were grown by the Czochralski method from melts having compositions varying between 48.6 and 58 mol% Li₂O. X-ray powder diffraction (XRD), inductively coupled plasma optical emission/mass spectrometry (ICP-OE/MS), ultraviolet–visible (UV–vis) absorption and the infrared (IR) spectrum were measured and are discussed in terms of the spectroscopic characterization. It was found that as the Li/Nb ratio increases in the melt, the Li/Nb ratio in the crystal also increases, the distribution coefficients of Fe and Zr ions decrease, the absorption edge shifts to a shorter wavelength, and the ZrO₂ threshold concentration of the samples decreases.     

Growth of Na modified potassium lithium niobate crystal by the Czochralski method

Transparent Na modified potassium lithium niobate (Na_0.23K_2.60Li_1.82Nb_5.35O_15.70; NKLN) crystal was successively grown by the Czochralski method using RF induction heating from melt composition Na₂O:K₂O : Li₂O:Nb₂O₅=2:30:25:43 mol%. NKLN crystal showed a tetragonal tungsten bronze structure with lattice constants a=12.5446±0.0010 Å and c=4.0129±0.0005 Å at room temperature. The dielectric constant along the c-axis ε₃₃ showed a sharp maximum around 480 °C. Optical transmission edge was 370 nm and optical transmission spectra showed no absorption at wavelengths ranging from 380 to 800 nm. The structural and optical properties of NKLN were similar to those of the near stoichiometric KLN crystals. We believe that the growth of NKLN by the Czochralski method has an advantage for a large size and high-quality crystal.     

Growth and spectroscopic properties of Er single doped and Er–Yb co-doped YAl3(BO3)4 crystals

Er³⁺-doped and Er³⁺–Yb³⁺ co-doped yttrium aluminum borate (YAB) single crystals have been grown by the top-seeded solution growth method using a new flux system, namely NaF–MoO₃–B₂O₃. The Er³⁺ concentrations were 1.3 mol% for both single doped and co-doped crystals and the Yb³⁺ concentration in the Er³⁺–Yb³⁺ co-doped crystal was 20.0 mol% in the raw materials. The distribution coefficients of Er³⁺ single doped and Er³⁺–Yb³⁺ co-doped crystals were measured. The polarized absorption and fluorescence spectra of Er³⁺–Yb³⁺ co-doped crystal were recorded and compared with those of Er³⁺ single doped crystal. The results demonstrate that Er³⁺–Yb³⁺ co-doped YAB crystal is a potential candidate for 1.55 μm laser materials.     

Improved growth of PbI2 single crystals

The phase equilibrium and the crystallization process of lead iodide (PbI₂) melt have been primarily investigated according to the lead–iodine phase diagram. It is found that the iodine evaporation and the segregated lead deposition are the two important factors that affect the PbI₂ crystal quality. The new method of Pulling U-type quartz growth ampoule has been made to impede the decomposition of PbI₂ and the vaporization and condensation of iodine. An orange and translucent PbI₂ single crystal of large size was obtained by the improved growth method, i.e. U-type ampoule pulling. Resistivity of the as-grown crystal is up to 4×10¹¹ Ω cm, and IR transmission is up to 45% in the region from 7800 to 450 cm⁻¹. Therefore, the improved growth method is a promising convenient new method for the growth of high quality PbI₂ crystals.     

Growth and Raman spectroscopic characterization of As4S4 (II) single crystals

As described by Kutoglu (1976 [16]), single crystals of As₄S₄ (II) phase have been grown using a new two-step synthesis that drastically increases the reproducibility that is attainable in synthetic experiments. First, through photo-induced phase transformation, pararealgar powder is prepared as a precursor instead of AsS melt. Then it is dissolved and recrystallized from CS₂ solvent. Results show that single crystals of the As₄S₄ (II) phase were obtained reproducibly through the dissolution–recrystallization process. Single crystals of As₄S₄ (II) obtained using this method were translucent and showed a uniform yellow-orange color. The crystal exhibits a platelet-like shape as a thin film with well-developed faces (0 1 0) and (0 1¯ 0). The grown crystals are as large as 0.50×0.50×0.01 mm. They were characterized using powder and single crystal X-ray diffraction techniques to confirm the phase identification and the lattice parameters. The As₄S₄ (II) phase crystallizes in monoclinic system with cell parameters a=11.202(4) Å, b=9.954(4) Å, c=7.142(4) Å, β=92.81(4)°, V=795.4(6) Å³, which shows good agreement with the former value. Raman spectroscopic studies elucidated the behavior of the substance and the relation among phases of tetra-arsenic tetrasulfide.     

Crystal growth and spectroscopic properties of erbium doped Lu2SiO5

A high optical quality erbium doped Lu₂SiO₅ single crystal has been grown by the Czochralski method. The distribution coefficient of Er³⁺ was measured to be ∼0.926. The absorption and emission spectra as well as the fluorescence decay curve of the excited state ⁴I_13/2 were measured at room temperature. The spectroscopic parameters were calculated using the Judd–Ofelt theory, and the J–O parameters Ω₂, Ω₄ and Ω₆ were found to be 4.451×10^-20, 1.614×10^-20 and 1.158×10^-20 cm², respectively. The room-temperature fluorescence lifetime of the Er³⁺⁴I_13/2→⁴I_15/2 transition was measured to be 7.74 ms. The absorption and emission cross-section as well as the gain cross-section in the eye-safe regime of 1400–1700 nm were also determined and discussed.     

Growth of single crystals of B28 at high pressures and high temperatures

A method of the high-pressure high-temperature synthesis of single crystals of orthorhombic high-pressure boron B₂₈ from metal solutions is presented. The method is based on the high-pressure multi-anvil technique. The feasibility of single-crystal growth was demonstrated in a number of experiments conducted at various pressure–temperature conditions with various precursors including β-boron of 99.99% purity and various metals (Cu, Au, and Pt) used as fluxes and capsule materials. It was found that after dissolution in metals at high pressures and high temperatures, boron crystallizes in the form of single crystals at low temperature. The process is accompanied by chemical reactions resulting in the formation of borides. The maximum length of the B₂₈ crystals achieved is ∼100 μm.     

Crystal growth and spectroscopic properties of Yb:CaYAlO4 single crystal

A Yb³⁺-doped CaYAlO₄ laser crystal has been grown by the Czochralski technique. The segregation coefficient was measured by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES). The cell parameters were analyzed with X-ray diffraction experiments. Color defects in Yb:CaYAlO₄ have been evidenced to be similar to those in undoped CaYAlO₄. The polarized absorption spectra and the fluorescence spectrum of the Yb:CaYAlO₄ crystal were measured at room temperature. The fluorescence decay time of the Yb³⁺ ion was investigated. The results show that Yb:CaYAlO₄ has potential as a laser gain medium for an ultrashort laser system.     

Preparation and characterization of Ni-incorporated FeS2 single crystals

Nickel-incorporated FeS₂ single crystals with various Ni compositions of Fe_0.99S₂:Ni_0.01, Fe_0.98S₂:Ni_0.02, Fe_0.96S₂:Ni_0.04, and Fe_0.9S₂:Ni_0.1 were grown by chemical vapor transport (CVT) method using ICl₃ as a transport agent. Physical properties of the Ni-incorporated FeS₂ single crystals were characterized using X-ray diffraction, Raman spectroscopy, electrical conductivity, and photoconductivity (PC) measurements. By means of the analyses of the X-ray diffraction patterns, the whole series of Ni-doped FeS₂ single crystals were determined to be single-phase and isostructural. Raman spectroscopy of the Ni-doped FeS₂ crystals was carried out at room temperature. Raman resonant peaks of the Ni-doped FeS₂ crystals demonstrate an energy red-shift behavior with respect to the increase of the dopant densities. Conductivity measurements show the resistivity of the Ni-doped FeS₂ decreased as the doping concentration of Ni is increased. Nickel is an n-type dopant, which behaves like a donor level existed near the conduction band edge of the synthetic FeS₂. On the other hand, dopant effect of nickel on the synthetic FeS₂ also destroys the photoconductive sensitivity in the photoconductivity measurements.     

Thermal-induced phase transition and assembly of hexagonal metastable In2O3 nanocrystals: A new approach to In2O3 functional materials

This paper reports on the thermal-induced performance of hexagonal metastable In₂O₃ nanocrystals involving in phase transition and assembly, with particular emphasis on the assembly for the preparation of functional materials. For In₂O₃ nanocrystals, the metastable phase was found to be thermally unstable and transform to cubic phase when temperature was higher than 600 °C, accompanied by assembly as well as evolution of optical properties, but the two polymorphs coexisted at the temperature ranging from 600 to 900 °C, during which the content of product phase and crystal size gradually increased upon increasing temperature. The assembly of In₂O₃ nanocrystals can be developed to fabricate In₂O₃ functional materials, such as various ceramic materials, or even desired nano- or micro-structures, by using metastable In₂O₃ nanocrystals as precursors or building blocks. The electrical resistivity of In₂O₃ conductive film fabricated by a hot-pressing route was as low as 3.72×10⁻³ Ω cm, close to that of In₂O₃ single crystal, which is important for In₂O₃ that is always used as conductive materials. The findings should be of importance for both the wide applications of In₂O₃ in optical and electronic devices and theoretical investigations on crystal structures.     

Sn3O4 single crystal nanobelts grown by carbothermal reduction process

This article reports on the growth of single crystal Sn₃O₄ nanobelts and SnO by a carbothermal reduction process in two different regions of a furnace tube. Even though intermediate tin oxide compounds (Sn₃O₄) have been observed experimentally, the study of structures based on them is a challenging task. Characterization data allowed us to propose that Sn₃O₄ nanobelts grew by vapor–solid mechanism while SnO grew by self-catalyst vapor–liquid–solid mechanism. Electrical measurements of a single Sn₃O₄ nanobelt were performed at different temperatures, revealing undoped semiconductor characteristics.     

Growth of SrFe12O19 nanowires under an induced magnetic field

Nanowires of SrFe₁₂O₁₉ with diameters of 100 nm and lengths of 2.5 μm have been successfully synthesized in a hydrothermal cell at 180 °C with an 0.35 T magnetic field applied. The growth behavior of the nanoparticles was compared with that under zero magnetic field. The X-ray diffraction patterns indicate that both of the two processes result in formation of pure SrFe₁₂O₁₉, however transmission electron microscope observations show that the morphology of the particles changed from flake-like in zero magnetic field into nanowires in a magnetic field. Compared to the sample obtained under zero magnetic field, the as-prepared one exhibits a higher saturation magnetization. The possible underlying mechanism responsible for the morphology change and the magnetic properties improvement were discussed.