A novel frequency sextupling scheme for optical mm-wave generation utilizing an integrated dual-parallel Mach-Zehnder modulator

A novel scheme is proposed for frequency sextupling mm-wave generation based on a laser and an integrated dual-parallel Mach-Zehnder modulator (MZM) without optical filter. Theoretical analysis is presented to suppress the undesired optical sidebands for the high quality generation of frequency sextupling mm-wave signal. The performance of the proposed scheme is evaluated by simulations. Utilizing the integrated MZM consisted of two sub-MZMs with extinction ratio of 30 dB, the optical sideband suppression ratio (OSSR) is as high as 29.9 dB and the radio frequency spurious suppression ratio (RFSSR) exceeds 24 dB without any optical or electrical filter. The impact of the nonideal RF driven voltage and phase difference of RF driven signal applied to two sub-MZMs of the integrated MZM on OSSR and RFSSR is discussed and analyzed. After transmission over fiber, the generated optical mm-wave signal demonstrates good performance. Furthermore, the performance of two cases for the proposed scheme is also compared.     

弱耦合光纤光栅外腔半导体激光器

报道作者对单频窄宽光纤光栅外腔半导体激光器的一些研究结果。理论上分析了外腔的引入对激光器的阈值增益和光谱线宽的影响，实验上用自行研制的光纤布拉格反射滤波器（ＦＢＲ）与普通多纵模半导体激光耦合，在１．５５μｍ波段，得到边模抑制比大于２５ｄＢ，线宽小于６０ｋＨｚ的激光输出。     

基于次谐波调制光注入半导体激光器获取窄线宽微波信号的实验研究

实验研究了处于单周期振荡的光注入半导体激光器在频率等于单周期振荡频率一半的1/2次谐波调制下所产生的微波信号的特性.实验结果显示:在合适的注入条件下,处于单周期(P1)振荡的光注入半导体激光器可输出频率可达26.5 GHz、光谱具有单边带结构的光生微波信号,但微波信号的线宽比较宽(MHz量级);通过采用频率为单周期振荡频率一半的次谐波信号调制光注入半导体激光器,可将微波线宽从十几MHz压缩到几十k Hz.进一步分析了次谐波调制信号的功率以及频率对微波信号的相位噪声的影响,并在由次谐波调制信号的功率和频率构成的参数空间绘制出了能实现次谐波频率锁定的分布区域.     

Generation of optical carrier suppression millimeter-wave signal using one dual-parallel MZM to overcome chromatic dispersion

In this paper, we have proposed a novel approach to generate optical carrier suppression (OCS) mm-wave with signal only carried by one first-order sideband using a dual-parallel MZM in radio-over-fiber (RoF) system, and the transmission performance was also investigated. As the optical mm-wave signal is transmitted along the fiber, there is no time shift of the data symbols resulting from the group velocity dispersion in the fiber because the signal is only modulated on one sideband. The simulation results showed that the eye diagram keeps open and clear even when the optical mm-wave signals are transmitted over 96-km and the power penalty is about 1-dB after fiber transmission distance of 60-km, which is quite consistent with our theoretical analysis. Furthermore, the proposed OCS optical mm-wave generation approach is also used in a full-duplex RoF link based on wavelength reuse at the base station for the uplink due to another pure sideband without carrying data. The bidirectional 2.5-Gbit/s data is successfully transmitted over 40-km standard single mode fiber with less than 0.5-dB power penalty in the simulation. Both the unidirectional RoF downlink and the full-duplex RoF system have good performance.     

Frequency-shifting submillimeter single-sideband receiver

A single sideband (SSB) receiver has been developed and implemented for use with a submillimeter sideband generator. While the sideband generator emits both an upper and lower sideband, and even some unshifted laser radiation, the receiver responds to only one sideband. The operator of the system can choose which sideband to receive. Rejection of the undesired signal is accomplished through selective frequency shifting coupled with the use of a commercially available single-sideband microwave mixer.     

Microwave photonic filter’s application on the microwave signal generation based on an active mode-locked fiber laser

A novel scheme which utilizes the microwave photonic filter technique for the optical generation of a microwave signal based on an active mode-locked fiber laser is proposed. A microwave signal generator using a microwave photonic filter based on a 2: 1 optical coupler with a fiber loop which can effectively suppress a low-order frequency component of the microwave signal is demonstrated and a ～10-GHz microwave signal is achieved based on an active mode-locked fiber laser with the original pulse repetition rate of ～5 GHz.     

Optical demultiplexing of millimeter-wave subcarriers for wireless channel distribution employing dual wavelength FBGs

An optical mm-wave demultiplexer is presented. Double sideband modulation with suppressed optical carrier and filtering properties of dual overwritten fiber Bragg gratings are the fundamentals for optical demultiplexing of mm-wave radio-on-fiber signals: using a single optical carrier, Millimeter-wave signals of 20 and 40 GHz frequencies carrying independent data are created, transmitted over fiber, demultiplexed and wireless distributed to be detected and data recovered in a mobile unit. Double sideband modulation with suppressed optical carrier yields no power penalty due to chromatic dispersion, while the filtering properties of the dual overwritten fiber Bragg gratings allow less than −40 dB electrical power interchannel leakage. Independent 2.5 Gb/s On-Off-keyed data have been successfully transmitted through the 20 and 40 GHz channels.     

The transmission performance degradation of the optical millimeter-wave signals by fiber chromatic dispersion

The influence of the fiber chromatic dispersion on double sideband (DSB), optical carrier suppression (OCS), and single sideband (SSB) optical mm-wave signals is investigated based on the Taylor expansion of the propagation constant and is verified by simulation. According to our theoretical results, the fading effect suppresses the signal power of the DSB optical mm-wave periodically in a cosine-like pattern, and it can be described by the zero-order Taylor expansion of the propagation constant. For the optical mm-wave with the signal modulated on two or more tones, the bit pulses of the mm-wave signal are distorted by the dispersion-inducing bit walk-off effect between tones, which is expressed by the first-order Taylor expansion of the propagation constant. Moreover, as the signal rate and the transmission distance are increased further, higher-order Taylor expansion of the propagation constant still degrades the optical mm-wave signal even if both the fading effect and the bit walk-off effect are eliminated completely. The distortion of the signal pulses of SSB optical mm-wave is derived based on the second-order Taylor expansion of the propagation constant. This degradation is verified by the simulation with the eye diagram evolution of the SSB optical mm-wave signal.     

单点相移光纤光栅光谱特性的研究与应用

可调谐窄线宽掺铒光纤激光器具有线宽窄、噪声低等优点,在光纤通信、光纤传感、相干探测和合成等方面有广泛的应用。根据传输矩阵法, 利用Matlab软件仿真出单点相移光纤光栅的透射谱,通过对不同相移量、不同相移点位置、不同光栅的长度以及不同纤芯有效折射率的单点相移光纤光栅透射谱进行分析,得到了影响其相移峰的透射率、线宽、位置的主要因素,并提出了一种利用相移量为π且相移点在中点的相移光纤光栅作为滤波窗口的可调谐窄线宽掺铒光纤激光器的方案。     

基于光电负反馈的光注入1550nm垂直腔面发射激光器产生窄线宽微波信号

基于1 550nm垂直腔面发射激光器在平行偏振光注入下呈现的单周期非线性动力学状态,进一步引入光电负反馈,得到了高质量的微波信号.实验研究结果表明:平行偏振光注入下,通过调节注入光的注入强度及频率,1 550nm垂直腔面发射激光器可呈现注入锁定、单周期、倍周期、混沌等多种非线性动力学状态;在合适的注入参量下,平行偏振光注入1 550nm垂直腔面发射激光器可产生光谱具有单边带结构、频率超过10GHz的光子微波信号,但该微波信号的线宽较宽(达MHz量级);进一步引入光电负反馈后,通过选取合适的光电反馈强度,可将该微波信号的线宽减小至一百多kHz(减小两个量级以上);在选择优化的反馈强度条件下,仅通过简单调节注入光强度,可实现窄线宽光子微波信号的频率在一定范围内连续可调谐.     

10 Gb/s optical carrier distributed network with W-band (0.1 THz) short-reach wireless communication system

Millimeter-wave (mm-wave) operated in W-band (75 GHz–0.11 THz) is of particular interests, since this frequency band can carry signals at much higher data rates. We demonstrate a 10 Gb/s optical carrier-distributed network with the wireless communication system. The mm-wave signal at carrier frequency of 0.1 THz is generated by a high speed near-ballistic uni-traveling carrier photodiode (NBUTC-PD) based transmitter (Tx), which is optically excited by optical short pulses. The optical pulse source is produced from a self-developed photonic mm-wave waveform generator (PMWG), which allows spectral line-by-line pulse shaping. Hence these optical pulses have high tolerance to fiber chromatic dispersion. The W-band 10 Gb/s wireless data is transmitted and received via a pair of horn antennas. The received 10 Gb/s data is envelope-detected and then used to drive an optical modulator at the remote antenna unit (RAU) to produce the upstream signal sending back to the central office (CO). 20 km single mode fiber (SMF) error free transmission is achieved. Analysis about the optimum repetition rate of the optical pulse source and the transmission performance of the upstream signal are also performed and discussed.     

All-optical generation of 40 Gb/s single sideband signals using a fiber Bragg grating

In this work, we demonstrate a reliable all-optical technique for performing optical double sideband (ODSB) to single sideband (OSSB) format conversion of a 40 Gb/s non-return-to-zero signal. It is based on the optimization of a detuned optical filter, which was implemented on a fiber Bragg grating (FBG) with a complex apodization profile. An OSSB signal with negligible distortion was obtained, as the FBG presented a nearly ideal frequency response. Higher tolerance to chromatic dispersion enabled by the OSSB signal in comparison to the ODSB signal was demonstrated on both simulation and experimental results.     

Photonic generation of a microwave signal by incorporating a delay interferometer and a saturable absorber

A novel approach to generate microwave signals is presented by employing a dual-wavelength erbium-doped fiber ring laser. By using a delay interferometer as a comb filter cascaded with a tunable bandpass filter and a saturable absorber formed by an unpumped polarization-maintaining erbium-doped fiber, a stable wavelength-tunable dual-wavelength single longitudinal-mode laser is achieved. A microwave signal at 20.07 GHz with a linewidth of <25 kHz is demonstrated by beating the two wavelengths at a photodetector.     

用于光频传递的通信波段窄线宽激光器研制及应用

通信波段窄线宽激光器在基于光纤的光学频率传递中有着重要应用. 本文报道了1550 nm超窄线宽光纤激光器的研制及其在光学频率传递中的初步应用结果. 利用一台激光光源, 分别锁定到两个参考腔上(精细度分别为344000和296000), 锁定后经拍频比对测得单台激光线宽优于1.9 Hz, 秒级频率稳定度为1.7×10^-14, 优于国内同类报道. 将研制的超窄线宽激光器用于光纤光学频率传递, 在50 km光纤盘上实现了 7.5×10^-17/s的传递稳定度, 较采用商用光纤激光器提高了3.2倍.     

一种改进的双边带调制产生光毫米波的方案

提出了应用于光纤无线通信系统中一种改进的双边带调制产生光毫米波方案。在中心站采用强度调制将射频信号调制到光载波上产生一个双边带信号,滤掉中心载波后,利用光交叉复用器把双边带信号的上下边带模分开,将数据速率为2.5Gbit/s的基带信号调制到下边带模后,再与未调信号耦合后产生光毫米波,然后通过单模光纤传输至基站,在基站经过光电转换后产生电毫米波信号。从理论上对该毫米波的色散特性进行了分析,发现毫米波的接收功率不会周期的衰减。同时通过实验研究表明,下行链路信号通过光纤能传输50km而不需要色散补偿,功率代价小于1dBm。因此,该方法产生的光毫米波能有效克服光纤色散引起的信号时延而导致的基带信号退化,适合于远距离传输。     

Optical Microwave and Millimeter Generation by Using Birefringent Fiber FP Cavity with Pulse Laser Injection

A novel optical microwave and millimeter generation by using single mode fiber FP cavity (SMFFPC) with pulse laser injection is proposed and experimentally demonstrated. The frequency of output signal is determined by the birefringence degree of the SMFFPC, a general relationship between output signal frequency of SMFFPC and birefringence degree of single mode fiber is derived. The proof of concept device consists of a light source, a polarizer controller, a modulator, a RF generator, a single mode fiber Fabry-Perot cavity, a strain inspector, an erbium doped fiber amplifier, a filter, a polarizer, and a digital communication analyzer. The results demonstrate the new concept of optical microwave and millimeter generation and the technical feasibility.     

可调谐掺铥光纤激光器线宽压缩及其超光谱吸收应用

可调谐二极管激光吸收光谱技术是一种应用非常广泛的吸收光谱测量技术.利用宽带可调谐窄线宽光源进行吸收光谱测量的超光谱吸收技术可以在单次扫描中获取一段连续光谱的所有吸收数据,可大大提高可调谐二极管激光吸收光谱技术的数据信息容量和光谱诊断能力.分析了在2μm波段对水进行超光谱吸收测量时对激光器输出线宽的具体要求.利用掺铥光纤在2μm波段较宽的发射谱,采用可调谐法布里-珀罗滤波器和光纤可饱和吸收体相结合的技术方案搭建了一台宽带调谐窄线宽的2μm光纤激光器.获得了1840—1900 nm约60 nm范围的调谐光谱输出,激光器静态线宽仅为0.05 nm.利用该光源对空气中水在2μm波段的吸收光谱数据进行了超光谱吸收测量,在1856—1886 nm约30 nm的光谱范围内分辨了35条水的吸收谱线.通过对不同线宽条件下1870—1880 nm范围内的理论吸收光谱数据进行对比发现,测量数据无法有效分辨分别位于1873 nm和1877 nm处与强吸收线相邻的两条吸收谱线,且测量结果与激光线宽在0.08 nm条件下的HITRAN2012光谱数据库最为接近.这表明,在动态扫描过程中激光器的线宽得到了展宽.     

High Stability Multi-Wavelength Source by Using Synchronized Etalon Filter in Superfluorescent Fiber Source

We demonstrate a new technique to generate a high stability multi-wavelength fiber source by inserting a synchronized etalon filter in superfluorescent fiber source. Multi-wavelength source can easily be obtained over the EDF gain region with the proposed schedule. By partially feedback diffracted spontaneous emission into erbium doped fiber medium, greater output power, extinction ration and narrower linewidth for each channel than that simply using the spectrum slicing technique is easy obtained. Stable output of multi-wavelength fiber source enables it to replace the DFB laser array with wavelength locker in DWDM application.     

Injection-locked fiber laser for tunable millimeter-wave generation

A dual-ring injection-locked fiber laser consisting of a ring of optoelectronic oscillator (OEO) and a ring of fiber laser is proposed and demonstrated for tunable millimeter-wave (mm-wave) generation. The approach combines the advantages of mm-wave generation based on OEOs and fiber lasers, which can generate a high-frequency, low-phase-noise, and a mode-hopping-free mm-wave signal with a large tuning range. A low-phase-noise mm-wave signal with a tunable frequency of 30-50 GHz and a tuning step of 10 GHz is obtained in a proof-of-concept experiment. The tuning range can be as large as 140 GHz if a high bandwidth photodetector is applied.     

全频域下窄线宽激光器光谱线宽的分析

窄线宽激光器的线宽表征方式通常采用延时自外差法测量技术。该技术是通过延时光纤差拍产生一个与待测激光线宽相关的洛伦兹频谱,因此该频谱只具有单一的线宽表现形式。为了能够观察到激光器的线宽和频率噪声在其傅里叶频率分布下的完整特性,报道了一种基于β算法计算窄线宽激光器线宽的方法。该方法是结合频率噪声中的白噪声和1/f噪声分别诱导不同激光线型的理论,从而确定激光线宽。首先,对β算法的基本原理进行了详细的分析说明。通过基于维纳-辛钦定理,分析了窄线宽激光器不同频率范围内的频率噪声和激光线宽的依赖关系。阐明了在截止频率趋于0和无穷大的两个范围条件时,激光频谱特性从高斯线型向洛伦兹线型演变。同时推导出使两种线型转换的截止频率表达式,并将其转换为频率噪声函数,该函数定义为β分子线。此时频率噪声分量中高斯线型的总和即为激光线宽计算公式;其次,对窄线宽激光器的频率噪声和激光线型进行数值仿真。将通过OEwaves公司的OE4000互相关零差相位/频率噪声自动测试系统测得的频率噪声谱密度,带入β算法理论公式中。结果显示：1/f噪声导致激光呈现高斯线型,线宽随截止频率的增加而增大。而白噪声将导致洛伦兹线型,线宽不再随截止频率而改变。此外,在低频区域,频率噪声电平远大于其傅里叶频率,噪声调制系数较高,该部分噪声可以决定线宽大小。因此,高斯线型区域对应的频率噪声的积分,即为待测激光器的线宽;在高频区域,频率噪声电平与其傅里叶频率相差较小,频率波动较快,噪声对线宽影响可以忽略。并且频率带宽在截止频率范围内,计算的线宽误差较小。最后,实验上运用β算法对RIO公司的1 550 nm低噪声窄线宽激光器的频率噪声功率谱密度进行积分计算,成功获得了其不同傅里叶频率分布下对应的激光线宽值。其中β分子线将频率噪声中的白噪声和1/f噪声分隔两部分：当频率噪声谱密度大于β分子线时,激光即为高斯线型,线宽随频率积分带宽的增加而减少;而频率噪声谱密度小于β分子线时,激光呈现洛伦兹线型,线宽为定值不再改变。同时为了对β算法进行实验验证,搭建了延迟光纤为50 km、移频频率为60 MHz的延时自外差法测量系统。对注入电流为110 mA的RIO 1 550 nm低噪声窄线宽激光器的线宽进行实验测量,测量结果表明激光线宽为1.8 kHz,与上述β算法中2.8 kHz的频率带宽积分结果一致。充分证明了此算法的准确性。β算法可以对任意类型的窄线宽激光器进行线宽表征,对窄线宽激光器的研究具有重要意义。