A new procedure for the speciation of mercury in water based on the transformation of mercury (II) and methylmercury (II) into stable acetylides followed by HPLC analysis

Conversion of mercury(II) and methylmercury(II) species dissolved in water into di(phenylethynyl)mercury and methyl(phenylethynyl) mercury takes place in satisfactory yield under alkaline conditions by stirring the aqueous solution with phenylacetylene at room temperature. Mercury speciation is simply obtained by HPLC analysis of the two organometallic species. The presence of heavy metals such as copper(II), zinc(II), cadmium(II) and lead(II) in concentrations 10000 times higher than mercury is tolerated, while little interference is displayed by humic acids and cysteine. Seawater samples can also be analysed following a properly adapted procedure.     

Simultaneous determination of cadmium(II), lead(II) and copper(II) by using a screen-printed electrode modified with mercury nano-droplets

We are presenting a strategy for the fabrication of disposable screen-printed electrodes modified with mercury nano-droplets and capable of sensing heavy metal ions. They were prepared by coating electrodes with a mixture of multi-walled carbon nanotubes and chitosan, this followed by adsorption of mercury. The resulting sensor was characterized by cyclic voltammetry and impedance spectroscopy. Also the effects caused by adsorption of mercury were investigated. It is shown that square wave anodic stripping voltammetry enables simultaneous determination of cadmium(II), lead(II) and copper(II), for which detection limits of 12, 23 and 20 nM, respectively, are found. Relative standard deviations for ten determinations at 0.6 µM concentrations of these ions are in the range of 3.0 to 5.7%. The applicability was tested by analyzing river water and showed recoveries between 94.1 and 104.6%, thus demonstrating its utility for in-field monitoring of these heavy metal ions.     

Voltammetric method for ultra-trace determination of total mercury and toxic metals in vegetables. Comparison with spectroscopy

A new procedure for the determination of mercury(II), copper(II), lead(II), cadmium(II) and zinc(II) traces in food matrices by square wave anodic stripping voltammetry and standard addition method is proposed. A rapid, inexpensive and multi-analyte analytical method suitable for food safety control is provided. Comestible vegetables were chosen as samples. A two-step, sequential determination was defined, employing two working electrodes: a gold electrode (GE) for mercury(II) and copper(II), and subsequently a hanging mercury drop electrode (HMDE) for copper(II), lead(II), cadmium(II) and zinc(II). No sample pre-treatment was needed. Spinach leaves, tomato leaves and apple leaves were employed as standard reference materials to optimize and defined the analytical procedure. The new method shows good selectivity, sensitivity, detectability and accuracy. A critical comparison with spectroscopic measurements is discussed. Spinach, lettuce and tomato samples sold on the market were analysed as real samples. Lead(II) and cadmium(II) concentration exceeded the relevant legal limits.      

Investigation of Copper(II) Interference on the Anodic Stripping Voltammetry of Lead(II) and Cadmium(II) at Bismuth Film Electrode

The bismuth‐coated electrode is known to be prone to errors caused by copper(II). This study investigates copper(II) interference at bismuth film electrode for the detection of lead(II) and cadmium(II). It was conducted using glassy carbon electrode, while the bismuth film was plated in situ simultaneously with the target metal ions at ? 1200 mV. Copper(II) presented in solution significantly reduced the sensitivity of the electrode, for example there was an approximately 70 % and 90 % decrease in peak signals for lead(II) and cadmium(II), respectively, at a 10‐fold molar excess of copper(II). The decrease in sensitivity was ascribed to the competition between copper and bismuth or the metal ions for surface active sites. Scanning electron microscopy (SEM) and energy dispersive X‐ray (EDX) analysis suggested a large decrease in the amount of bismuth nanoparticles formed on the electrode surface in the presence of copper(II) occurred, validating the competition between copper and bismuth ions for surface active sites. Recovery of the stripping signal of lead(II) and cadmium(II) was obtained by adding ferrocyanide ion to the solution. Finally, the proposed method was successfully applied to determine lead(II) and cadmium(II) in water samples and the method was validated by ICP‐MS technique.     

Activated carbon cloth filled pipette tip for solid phase extraction of nickel(II), lead(II), cadmium(II), copper(II) and cobalt(II) as 1,3,4-thiadiazole-2,5-dithiol chelates for ultra-trace detection by FAAS

A solid phase extraction method is established for preconcentration of nickel, lead, cadmium, copper and cobalt using pipette tip solid phase extraction. The presented process was dependent on chelation of analytes with 1,3,4-thiadiazole-2,5-dithiol, then allowing the solution to flow through an activated carbon cloth packed pipette tip. The adsorbed metal chelates on the surface of activated carbon cloth were eluted by 5 mL of 3 M HNO₃. The concentrations of nickel, lead, cadmium, copper and cobalt were detected using a flame atomic absorption spectrometer (FAAS). The pipette tip solid phase extraction exhibit a preconcentration factor of 120. The limit of detection values were 2.7, 1.7, 1.3, 2.0 and 2.9 µg L^?1 for Ni(II), Pb(II), Cd(II), Cu(II) and Co(II), respectively. Validation of the method was checked by the analysis of TMDA-53.3 and TMDA-64.2 certified reference materials. The method was successfully applied for water and fertiliser samples.     

Potentiometric stripping analysis for zinc,cadmium. lead and copper in sea water

Analytical procedures for the determination of zinc(II), cadmium (II), lead(II) and copper(II) in sea water by potentiometric stripping analysis are described. The results are compared with those obtained by a combined solvent extraction-atomic absorption method both in the laboratory and on-board ship. The detection limits for zinc, cadmium, lead and copper are 0.03, 0.03, 0.01 and 0.02 μg l^-1, respectively, for a total analysis time of about 75 min. A very thin mercury film is useful in the determination of lead and copper.     

Selective stripping voltammetric determinations employing cells for electrolysis with simultaneous ion-exchange or solvent extraction

Cells have been designed for stripping-voltammetry analyses employing graphite working electrodes and mercury film electrodes on a graphite support, permitting ion-exchange or solvent extraction separation simultaneously with the pre-electrolysis. The ion-exchange separation was tested on the determination of mercury in the presence of excess of copper(II), lead and cadmium and on the determination of bismuth in the presence of excess of copper(II). The solvent extraction separation was tested on the determination of mercury(II) in the presence of copper(II), lead and cadmium and the determination of copper(II) in the presence of bismuth. Very good results were obtained by using ion-exchange, where the sensitivity and precision of the determination are comparable with those obtained in the determinations without separation, the separation efficiency being very high, limited virtually only by the capacity of the ion-exchanger used. The solvent extraction separations yielded poorer results: the sensitivity of the determination is decreased substantially, the separation efficiency is not very high and difficulties arise from the adsorption of the organic phase on the electrode surface.     

A Robust Electrochemical Sensor Based on Butterfly-shaped Silver Nanostructure for Concurrent Quantification of Heavy Metals in Water Samples

Heavy metals in drinking water have become a severe threat to human health. Detection of heavy metals has been achieved by electrochemical sensors that are modified with complex nanocomposites; however, reproducibility of these sensors is still a big challenge when applied in commercial settings. Here, a simple, very robust, and sensitive electrochemical sensor based on a screen-printed carbon electrode modified with butterfly-shaped silver nanostructure (AgNS/SPCE) has been developed for the concurrent determination of cadmium (II), lead (II), copper (II), and mercury (II) in water samples. The electrochemical behavior of the modified electrodes was investigated using cyclic voltammetry and differential pulse anodic stripping voltammetry. The AgNS/SPCE showed distinct peak potentials and a significant increase in the peak currents for all heavy metals, attributed to the high electrical conductivity and electrocatalytic activity of the synthesized butterfly-shaped AgNS. Moreover, the excellent stability and sensitivity towards simultaneous quantification of heavy metals have been obtained with detection limits of 0.4 ppb, 2.5 ppb, 7.3 ppb, and 0.7 ppb for Cd (II), Pb (II), Cu (II), and Hg (II), respectively. Besides, the constructed sensor was successfully applied to simultaneously quantify target heavy metals in spiked water samples. Owing to excellent sensitivity, high robustness, affordability, and fast response, the presented electrochemical sensor could be incorporated into a portable and miniaturized potentiostat device, making it a promising method for on-site water analysis.     

Optical chemical sensors (Micro- and Nanosystems) for analysis of liquids

A number of peculiar analytical systems applied in production of detecting elements for chemical sensors were considered, in which organic reagents are immobilized on opaque and optically transparent polymeric matrices. Fibrous non-fabricated materials filled with powdered ion exchangers (Vernadsky Institute of Geochemistry and Analytical Chemistry, Russian Academy of Sciences) and polymeric films coated with a high-purity gelatin layer (Mendeleev Russian University of Chemical Technology) were suggested as solidstate matrices. The conditions for determination of elements at MPC (maximal permissible concentration) levels were identified. Rapid, highly sensitive and selective techniques were developed for reflectance-spectroscopic determination of coexisting mercury(II), cadmium(II) and lead(II); chromium(VI), copper, and nickel; lanthanum, uranium(VI), and thorium, as well as for spectrophotometric determination of calcium, thorium, nitrite, and sulfate ions. Sensitive optical sensors suitable both for single control step and long-term monitoring of the content of the elements in water objects were proposed.     

Solid-phase extraction and determination of ultra trace amounts of lead,mercury and cadmium in water samples using octadecyl silica membrane disks modified with 5,5′-dithiobis(2-nitrobenzoic acid) and atomic absorption spectrometry

A simple and fast method for preconcentration and determination of ultra trace amounts of lead(II), mercury(II) and cadmium(II) in water samples is presented. Lead, mercury and cadmium adsorbed quantitatively during passage of water samples (pH?=?7, flow rate?=?20 mL min^?1) through octadecyl silica membrane disks modified with 5,5′-dithiobis(2-nitrobenzoic acid). The retained lead, mercury and cadmium are then stripped from the disk with a minimal amount of 1 M hydrochloric acid solution as eluent, and determined by atomic absorption spectrometry. The influence of flow rates of the eluent and sample solution, the amount of ligand, type and least amount of eluent, pH of sample, effect of other ions and breakthrough volume are determined. The breakthrough volume of the method is greater than 2000 mL for lead and greater than 1500 mL for mercury and cadmium, which results in an enrichment factor of 200 for lead and an enrichment factor of 150 for both mercury and cadmium. The limit of detection of the proposed method is 177, 2 and 13 ng l^?1 for lead, mercury and cadmium, respectively.     

Developing On-Site Trace Level Speciation of Lead,Cadmium and Zinc by Stripping Chronopotentiometry (SCP): Fast Screening and Quantification of Total Metal Concentrations

Electrochemical stripping techniques are interesting candidates for carrying out onsite speciation of environmentally relevant trace metals due to the existing low-cost portable instrumentation available and the low detection limits that can be achieved. In this work, we describe the initial analytical technique method development by quantifying the total metal concentrations using Stripping Chronopotentiometry (SCP). Carbon paste screen-printed electrodes were modified with thin films of mercury and used to quantify sub-nanomolar concentrations of lead and cadmium and sub-micromolar concentrations of zinc in river water. Low detection limits of 0.06 nM for Pb(II) and 0.04 nM for Cd(II) were obtained by the standard addition method using a SCP deposition time of 180 s. The SCP results obtained for Pb(II) and Cd(II) agreed with those of inductively coupled plasma mass spectrometry (ICP-MS). The coupling of SCP with screen-printed electrodes opens up excellent potential for the development of onsite speciation of trace metals. Due to the low analysis throughput obtained for the standard addition method, we also propose a new, more rapid screening Cd(II) internal standard methodology to significantly increase the number of samples that can be analyzed per day.     

Comparison of physicochemical speciation procedures with metal toxicity to chlorella pyrenoidosa

Metal speciation as measured by anodic stripping voltammetry (ASV), adsorption on a resin with adsorbed hydrated aluminium oxide, and dialysis with receiving resins is compared with the toxicity of the metals to the freshwater green alga Chlorella pyrenoidosa Chick. In the presence of natural and synthetic ligands, similar labile fractions of metals were obtained for ASV at three electrodes (hanging mercury drop electrode, mercury film electrode and Nafion-coated mercury film electrode). The toxic fractions determined by ASV and bioassay were in reasonable agreement for zinc, cadmium and copper, and alteration of the analytical conditions provided some measure of agreement for lead. The resin with adsorbed hydrated aluminium oxide correlated well with bioassay for copper, but over-estimated lead toxicity and under-estimated cadmium toxicity. Dialysis with receiving resins under-estimated metal bioaccumulation in the presence of ligands. Metal speciation analysis for water samples gave higher toxic fractions for metals in samples of polluted river water and road runoff samples than those found in pristine river water.     

Potentiometric determination of stability constants of cyanoacetato complexes of cobalt(II), nickel(II), copper(II), zinc(II), cadmium(II) and lead(II)

Stability constants of cyanoacetato complexes of cobalt(II), nickel(II), copper(II), zinc(II), cadmium(II) and lead(II) were determined potentiometrically at 25.0 +/- 0.1 degrees and ionic strength 2M (sodium perchlorate). The stability constants were evaluated by a weighted least-squares method.     

Effect of mercury(II) on metal complex labilities determined by direct-current anodic stripping voltammetry on a thin mercury film electrode

The labilities of copper, lead and cadmium complexes with fulvic acid, nitrilotriacetic acid and an iron-humic acid colloid were studied on a preplated thin mercury film electrode and with in-situ plating of mercury on a glassy carbon electrode. In the presence of mercury(II) the apparent labilities based on direct-current anodic stripping voltammetric peak-area measurements increased for each of the cadmium and lead species and for the copper iron-humic acid colloid species. In contrast, for the copper complexes with nitrilotriacetic acid and fulvic acid the lability was not measurably altered by mercury(II); it is inferred that they do not undergo rapid metal exchange with mercury(II).     

Comparative study of copper(II) and cadmium(II) salts as catalytic reagents in the determination of mercury by continuous-microflow cold vapour atomic absorption spectrometry

A continuous-microflow method with cold vapour atomic absorption spectrometric detection was used for the determination of mercury. A comparison of copper(II) and cadmium(II) salts as catalytic reagents is described in detail It was found that in the presence of at least 80 mg 1^?1 of copper(II) salt a similar signal was obtained for both inorganic mercury [mercury(II) chloride]and organic mercury [methylmercury(II) chloride]. With a cadmium(II) salt at least 100 mg 1^?1 were required.     

Determination of mobile form contents of Zn, Cd, Pb and Cu in soil extracts by combined stripping voltammetry

The amount of mobile forms of Zn, Pb, Cd and Cu in extracts obtained by treating soil samples with ammonium nitrate were determined by an appropriate combination of anodic and cathodic stripping voltammetry with hanging mercury drop electrode. Every analysis required three mercury drops: on the first one, zinc was determined; on the second, cadmium and lead; on the third, copper was determined. Zinc, lead and cadmium were determined by conventional differential-pulse anodic stripping voltammetry. For copper determination, adsorptive differential-pulse cathodic stripping voltammetry with amalgamation using chloride ions as a complexing agent was applied. The standard deviation of the results was from 1 to 10% depending on the metal content in the sample. Voltammetric results were in good agreement with the AAS analysis. No microwave digestion of soil extracts was necessary.     

A collaborative study of four methods of assay of benzylpenicillin

The assay of benzylpenicillin by iodimetric titration, spectrophotometry with a mercury(II) chloride—imidazole reagent, titration with mercury(II) nitrate in acetate buffer solution, and titration with mercury(II) perchlorate in aqueous pyridine solution, was examined in four laboratories. The first two methods were applied to two samples (the third one being the reference sample), the mercury(II) nitrate titration to three, and the mercury(II) perchlorate method to two samples. The four methods gave very similar results, but the purity obtained with the mercury(II) perchlorate method was slightly lower, and this procedure is less desirable because pyridine is used as solvent. There were no great differences in the relative standard deviations of the four methods. The titration with mercury(II) nitrate is preferred because it is an absolute method.     

Flotation-separation and ICP-AES determination of ultra trace amounts of copper, cadmium, nickel and cobalt using 2-aminocyclopentene-1-dithiocarboxylic acid.

A rapid flotation method for separation and enrichment of ultra trace amounts of copper(II), cadmium(II), nickel(II) and cobalt(II) ions from water samples is established. At pH 6.5 and with sodium dodecylsulfate used as a foaming reagent, Cu2+, Cd2+, Ni2+ and Co2+ were separated simultaneously with 2-aminocyclopentene-1-dithiocarboxylic acid (ACDA) added to 1 l of aqueous solution. The proposed procedure of preconcentration is applied prior to the determination of these four analytes using inductivity coupled plasma-atomic emission spectrometry (ICP-AES). The effects of pH, concentration of ACDA, applicability of different surfactants and foreign ions on the separation efficiency were investigated. The preconcentration factor of the method is 1000 and the detection limits of copper(II), cadmium(II), nickel(II) and cobalt(II) ions are 0.078, 0.075, 0.072 and 0.080 ng ml(-1), respectively.     

Thioacetamide chemically immobilized on silica gel as a solid phase extractant for the extraction and preconcentration of copper(II), lead(II), and cadmium(II)

Thioacetamide immobilized on silica gel was prepared via the Mannich reaction. The extraction and enrichment of copper(II), lead(II), and cadmium(II) ions from aqueous solutions has been investigated. Conditions for effective extraction are optimized with respect to different experimental parameters in both batch and column processes prior to their determination by flame atomic absorption spectrometry (FAAS). The optimum pH ranges for quantitative adsorption are 4.0-8.0, 2.0-7.0, and 5.0-10.0 for Pb(II), Cu(II), and Cd(II), respectively. Pb(II) and Cd(II) can be desorbed with 3 mol/L and 0.1 mol/L HCl/HNO3, and Cu(II) can be desorbed with 2.5% thiourea. The adsorption capacity of the matrix has been found to be 19.76, 16.35, and 12.50 mg/g for Pb(II), Cu(II), and Cd(II), respectively, with the preconcentration factor of approximately equal to 300 for Pb(II) and approximately equal to 200 for Cu(II) and Cd(II). Analytical utility is illustrated in real aqueous samples generated from distilled water, tap water, and river water samples.     

Synthesis, Spectral and Thermal Studies of o-vanillin Oxime Complexes of Zinc(II), Cadmium(II) and Mercury(II)

Zinc(II), cadmium(II) and mercury(II) complexes of o-vanillin oxime have been synthesized and characterized by different physicochemical techniques. All the complexes have been subjected to non-isothermal decomposition studies in nitrogen atmosphere using thermogravimetry. The kinetic parameters for the decomposition of these complexes were evaluated using different methods and comparatively better results were obtained by these different methods. It has also been found that the decomposition processes of all these complexes follow first order kinetics. This revised version was published online in July 2006 with corrections to the Cover Date.