Distribution and thermophysical properties of n-heptacosane molecules confined in carbon nanotube

Molecular dynamics (MD) simulations were performed to provide an insight about the molecule distribution and thermophysical properties of n-heptacosane confined in the (25, 25) single-walled carbon nanotube (CNT). The results show that an orderly distribution of n-heptacosane molecules along the CNT inner wall is clearly observed. Meanwhile, n-heptacosane confined in CNT exhibits an increased self-diffusion coefficient, a decreased melting point and an enhanced thermal conductivity, compared to the bulk. The simulations reveal that MD is an effective and convenient method to understand the variation characteristics of alkane-based phase change materials confined in CNT on molecular and atomic scale.     

Validation of the rotational vector Preisach model with measurements and simulations of vectorial minor loops

Carbon nanotube reinforced Cu–Ti alloy (CNT/Cu–Ti) composites are fabricated by a powder metallurgical method. The interfacial bonding of CNT/Cu–Ti composites is evidently improved, which is attributed to the formation of a thin layer of TiC at the interface. The thermal conductivity of the composites increases by 7.5 % and 15.1 % compared to that of Cu–Ti matrix at CNT loadings of 5 vol.% and 10 vol.%, respectively. The matrix-alloying is therefore an effective way to enhance the thermal conductivity of CNT/Cu composites.     

碳纳米管Y形分子结的热导率与热整流现象

基于碳纳米管Y形分子结的结构重构, 通过非平衡分子动力学方法和量子修正, 模拟分析了Y形分子结的热导率和热整流现象. 研究表明: 相对单根完整碳管, Y形分子结在不同温度下导致热导率大约12%–85%的下降; Y结主干向分支方向的导热能力强于分支向主干方向的导热能力; Y结降低热导率的作用随着温度的升高逐渐减小; Y结的热整流效果随着温度的上升先减弱后增强. 关键词： 碳纳米管 热导率 热整流     

On the thermal expansion of CNT/Cu composites for electronic packaging applications

Carbon nanotubes (CNTs) exhibit both excellent high thermal conductivity and low coefficient of thermal expansion (CTE), which are an ideal reinforcement in composite materials for high performance electronic packaging applications. In the present study, CNT/Cu composites containing CNTs varying from 0 vol.% to 15 vol.% are prepared, and their CTE behavior is studied in detail. The results indicate that the CTE of 0–10 vol.% CNT/Cu composites is significantly decreased with increasing CNT content. However, as the CNT content increases to 15 vol.%, the decrease in CTE of the composites is pronouncedly reduced. Possible mechanisms are discussed in combination with CTE model predictions.     

Novel Cu–Cr alloy matrix CNT composites with enhanced thermal conductivity

Carbon nanotubes (CNTs) are incorporated into the Cu–Cr matrix to fabricate bulk CNT/Cu–Cr composites by means of a powder metallurgy method, and their thermal conductivity behavior is investigated. It is found that the formation of Cr₃C₂ interfacial layer improves the interfacial bonding between CNTs and Cu–Cr matrix, producing a reduction of interfacial thermal resistance, and subsequently enhancing the thermal conductivity of the composites. The thermal conductivity of the composites increases by 12 % and 17 % with addition of 5 vol.% and 10 vol.% CNTs, respectively. The experimental results are also theoretically analyzed using an effective medium approximation (EMA) model, and it is found that the EMA model combined with a Debye model can provide a satisfactory agreement to the experimental data.     

β型锑烯热电输运性质的第一性原理研究

利用第一性原理与半经典玻尔兹曼方程，计算并分析β型锑烯的声子色散、声子群速度、声子弛豫时间、晶格热导率及不同温度下的塞贝克系数、电导率和电子热导率随化学势的变化；结果表明：β型锑烯由于非平面六角结构，三支声学声子在Γ点附近均呈线性变化；声学声子对整个晶格热导率的贡献高达96.68%，而光学声子仅仅占到3.32%；由于较大的声光带隙（a-o gap）导致LA支在声子群速度和弛豫时间中占据主导地位，从而增大了LA支声子对整个热导的贡献；热电优值随温度的升高而增大，在费米面附近其绝对值最大可达0.275.     

Influences of Carbon Nanotube Networking on the Conductive,Crystallization, and Thermal Expansion Behaviors of PA610-Based Nanocomposites

The electrical, crystallization and thermal expansion behaviors of polyamide 610 (PA610)/multi-walled carbon nanotube (CNT) nanocomposites prepared by melt mixing were investigated. Electron microscopy (Scanning Electron Microscopy and Transmission Electron Microscopy) revealed that a good dispersion of CNT and CNT network was obtained in the PA610 matrix. Addition of CNT to PA610 matrix led to polymer nanocomposites exhibiting higher electrical conductivity and lower thermal expansion. The network of CNT in the PA610 matrix, which can be tuned by the loading of CNT and the melt isothermal treatment, was found to play an important role in reducing thermal expansion and achieving higher conductivity. Furthermore, it was shown that significant reduction in thermal expansion in PA610/CNT nanocomposites was due to both thermally insensitive CNT and formation of CNT network.     

Investigation of Laminar Convective Heat Transfer of a Novel Tio2–Carbon Nanotube Hybrid Water-Based Nanofluid

The current study was conducted to investigate the convective heat transfer coefficient of a novel TiO₂–CNT hybrid nanofluid through the shell-and-tube heat exchanger under a laminar flow and the effects of temperature and mass fraction on it. TiO₂–CNT hybrid nanofluids were prepared using a new and modified hydrolysis technique. The thermal conductivity of the TiO₂–CNT hybrid nanofluid and other thermo-physical properties were assessed. Results indicate that the effective thermal conductivity and heat transfer coefficient of the base fluid was influenced significantly and increased by the 0.2 wt% of this novel hybrid nanofluid in distilled water.     

基于稳态电热拉曼技术的碳纳米管纤维导热系数测量及传热研究

利用稳态电热拉曼技术测量了碳纳米管纤维对流换热环境下的导热系数. 该方法基于材料拉曼信号与温度之间的关系, 实时探测一维材料在不同电加热(内热源)下的中心点温度, 利用对流环境下的稳态导热模型推导出材料的导热系数, 实现了一维微纳材料热物性的无损化和非接触式测量. 实验发现: 碳纳米管纤维的导热系数远低于单根碳纳米管的导热系数, 但高于碳纳米管堆积床的导热系数. 这表明碳纳米管体材料的热物性主要取决于内部管束的列阵和管束间的接触热阻.     

Thermal properties of continuously spun carbon nanotube fibres

As indicated by theory and experimental measurements individual carbon nanotubes (CNTs) have very high values of thermal conductivity. One of the challenges is to achieve high thermal conductivity in macroscopic assemblies of CNTs such as fibres, films and composites, paving the way to a wide range of applications. CNT fibres have tremendous potential in succeeding as the future materials for a variety of applications when properties at the nanoscale are translated to their macroscopic assemblies. In this paper we report the measurements of thermal conductivity of continuously spun CNT fibres and its dependence on temperature. Thermal conductivity measurements were performed using in-house built temperature sensing microscope probe. Specific thermal conductivity of CNT fibres showed an order of magnitude advantage over the traditional materials used for heat dissipation.     

Controlling the electrostatic discharge ignition sensitivity of composite energetic materials using carbon nanotube additives

Powder energetic materials are highly sensitive to electrostatic discharge (ESD) ignition. This study shows that small concentrations of carbon nanotubes (CNT) added to the highly reactive mixture of aluminum and copper oxide (Al + CuO) significantly reduces ESD ignition sensitivity. CNT act as a conduit for electric energy, bypassing energy buildup and desensitizing the mixture to ESD ignition. The lowest CNT concentration needed to desensitize ignition is 3.8 vol.% corresponding to percolation corresponding to an electrical conductivity of 0.04 S/cm. Conversely, added CNT increased Al + CuO thermal ignition sensitivity to a hot wire igniter.     

受限于对称性破缺狭缝间氢键流体的相平衡研究

利用密度泛函理论并结合改进的基本度量理论研究了受限于对称性破缺狭缝间氢键流体的相平衡. 首先根据氢键流体的吸附-脱附等温线及相应巨势获得不同条件下氢键流体的相图. 进一步讨论了氢键作用、狭缝间距、狭缝与流体分子间相互作用及对称性破缺程度等因素对氢键流体相平衡的影响. 结果表明, 由于狭缝与流体分子及流体分子间的相互作用存在竞争, 使得受限于对称性破缺条件下的氢键流体呈现更为复杂的相态特征.     

Diffusion of CO2/CH4 confined in narrow carbon nanotube bundles

ABSTRACT

The diffusion of a CO₂/CH₄ mixture in carbon nanotube (CNT) bundles was studied using molecular simulations. The effect of diameter and temperature on the diffusion of the mixture was investigated. Our results show that the single-file diffusion occurs when CO₂ and CH₄ are confined in CNTs of diameter less than 1.0 nm. In CNTs of diameter larger than 1.0 nm, both molecules diffuse in the Fickian style. The transition from single-file to Fickian diffusion was demonstrated for both CO₂ and CH₄ molecules. A dual diffusion mechanism was observed in the studied (20, 0) CNT bundle, single-file diffusion of CO₂ in the interstitial sites of (20, 0) CNT bundle and Fickian diffusion of CO₂ and CH₄ in the pores. For CO₂, the interaction energies (CO₂–CO₂ and CO₂–CNT) are larger than that of CH₄ in all cases. But only a very small difference in the diffusion coefficient was observed between CO₂ and CH₄. Temperature has a negligible effect on the difference between diffusion coefficients of CO₂ and CH₄ in the studied CNT bundles. The adsorption, diffusion and permeation selectivities are discussed and compared, and the adsorption is demonstrated to be the rate limiting step for the separation of CO₂/CH₄ in CNT bundle membranes.     

碳纳米管受限空间对共轭高分子聚(9,9-二辛基芴-2,7-二基)链段运动行为的影响

在纳米受限空间中,高分子往往会表现出与本体状态不同的性质,如异常的链段运动特性及晶相间转变行为等,这些性质对于研究和开发新型高分子材料具有重要的意义,因此针对受限环境下高分子的物理化学特性研究也一直是高分子界关注的焦点.本文通过化学气相沉积法制备垂直取向排列的多壁碳纳米管阵列,借助溶剂润湿–收缩法获得规整的高密度阵列结构,其取向排列的碳纳米管间隙形成了准一维的纳米受限空间,尺寸在5—50 nm尺度下可调.进一步将共轭高分子聚(9,9-二辛基芴-2,7-二基)(PFO)填充到碳管间隙的纳米空间中,制备PFO与取向多壁碳纳米管阵列复合膜.结果发现在碳纳米管形成的纳米受限空间中,PFO的链段热运动行为与本征态PFO薄膜相比受到了明显的抑制,不同晶型间转变速度大大减缓,提高了构象的热稳定性,同时取向排列的碳纳米管对PFO分子链取向排列分布具有明显的诱导作用,有利于获得高性能的PFO晶体.这种高密度取向排列的碳纳米管阵列结构未来可以用于制备优良发光性能及高稳定性的PFO光电器件.     

Graphene oxides and carbon nanotubes embedded in polyacrylonitrile-based carbon nanofibers used as electrodes for supercapacitor

This study investigates the use of graphene oxides (GOs) and carbon nanotubes (CNTs) embedded in polyacrylonitrile-based carbon nanofibers (GO–CNT/CNF) as electrodes for the supercapacitor. GO–CNT/CNF was prepared by electrospinning, and was subsequently stabilized and activated. The specific capacitance of GO–CNT/CNF is 120.5 F g⁻¹ in 0.5 M Na₂SO₄ electrolyte, which is higher than or comparable to the specific capacitances of carbon-based materials in neutral aqueous electrolyte, as prepared in this study. GO–CNT/CNF also exhibits a superior cycling stability, and 109% of the initial specific capacitance after 5000 cycles. The high capacitance of GO–CNT/CNF could be attributed to the edge planes and the functional groups of GO, the highly electrical conductivity of CNT, and the network structure of the electrode.     

Adjustable thermal conductivity in carbon nanotube nanofluids

Homogeneous and stable nanofluids have been produced by suspending well dispersible multi-walled carbon nanotubes (CNTs) into ethylene glycol base fluid. CNT nanofluids have enhanced thermal conductivity and the enhancement ratios increase with the nanotube loading and the temperature. Thermal conductivity enhancement was adjusted by ball milling and cutting the treated CNTs suspended in the nanofluids to relatively straight CNTs with an appropriate length distribution. Our findings indicate that the straightness ratio, aspect ratio, and aggregation have collective influence on the thermal conductivity of CNT nanofluids.     

碳纳米管-石墨烯纳米带过渡连接处的力学稳定性与热传导性质研究

任何的非平面连接,材料连接处的材料失配都能导致材料局部或整体性质的改变.本文以纵向拉开的碳纳米管(CNT)为研究对象,采用非平衡态分子动力学(NEMD)的模拟方法,通过改变CNT纵向拉开的剧烈程度,即CNT向石墨烯纳米带(GNR)过渡转变的开角大小,研究其力学稳定性和热传导性质的变化.结果表明,CNT到GNR的过渡越剧烈,连接处的开角越大,其局部热导率越高,单位长度的热阻越小;对于不同管径的CNT来说,连接处的最大开角恒定不变,为16.3°.     

Effects of fullerene coalescence on the thermal conductivity of carbon nanopeapods

The heat conduction and its dependence on fullerene coalescence in carbon nanopeapods (CNPs) have been investigated by equilibrium molecular dynamics simulations. The effects of fullerene coalescence on the thermal conductivity of CNPs were discussed under different temperatures. It is shown that the thermal conductivity of the CNPs decreases with the coalescence of encapsulated fullerene molecules. The thermal transmission mechanism of the effect of fullerene coalescence was analysed by the mass transfer contribution, the relative contributions of phonon oscillation frequencies to total heat current and the phonon vibrational density of states (VDOS). The mass transfer in CNPs is mainly attributed to the motion of encapsulated fullerene molecule and it gets more restricted with the coalescence of the fullerene. It shows that the low-frequency phonon modes below 20 THz contribute mostly to thermal conductivity in CNPs. The analysis of VDOS demonstrates that the dominating contribution to heat transfer is from the inner fullerene chain. With the coalescence of fullerene, the interfacial heat transfer between the CNT and fullerene chain is strengthened; however, the heat conduction of the fullerene chain decreases more rapidly at the same time.     

碳纳米管的生长机理、可控生长及应用探索

碳纳米管的可控制生长,及其宏观尺度结构的制备,对于碳纳米管的应用具有重要的意义,为了实现准确的生长控制,对碳纳米管生长机理的深入了解是不可缺少的前提条件.文章介绍了我们近年来在碳纳米管生长机理、可控生长及其应用方面的一些进展.通过引入13C标记法,我们证实了化学气相沉积法中碳纳米管以析出模式生长;实时改变生长的气相成份和流量,可以在碳纳米管阵列上留下标记序列,并据此测量出其生长速率及活化能.将超顺排碳纳米管阵列的合成扩展到4英寸规模,并发展了用挥发性有机溶剂处理碳纳米管线的方法,大大提高了其强度和可操作性.处理后的碳纳米管线可以方便地用于热电子源、高电流密度冷阴极以及荧光灯等.热界面材料在IT产业中具有重要的应用背景,我们用碳纳米管阵列制备的复合材料具有极高的热导率和极低的界面热阻,同时发展了化学修饰、端部剪裁、金属集热层等新技术以制备高性能的碳纳米管热界面材料.     

SiO_2气凝胶导热机理的分子动力学模拟研究

本文采用分子动力学方法,选用Lennard-Jones势函数,对氩分子在SiO2气凝胶骨架结构间空隙中的运动进行了平衡分子动力学模拟(EMD)和非平衡分子动力学模拟(NEMD),分析其能量输运特性.结果表明:在骨架空隙尺寸为15nm条件下,气凝胶内部氩分子的扩散系数仅为同等条件下自由空间内氩分子扩散系数的50.35%,...