Conductive TiN thin layer-coated nitrogen-doped anatase TiO<Subscript>2</Subscript> as high-performance anode materials for sodium-ion batteries

Nitrogen-doped anatase titanium oxide (N-TiO₂) with enhanced electronic conductivity induced by titanium nitride (TiN) thin layer coating was employed as high-performance anode material for sodium-ion batteries. The TiN thin layer can not only dramatically increase the electronic conductivity among crystal grains but also alleviate the volume expansion to consolidate the structure during long-term sodiation and desodiation process. The composite exhibits an excellent electrochemical performance, delivering a high specific capacity of 226.9 mA h g^?1 at 0.1 C and owning excellent rate capability of 158.3 mA h g^?1 at 10 C high rate. Moreover, the composite has no obvious capacity decay after 500 cycles at 1 C, showing its superior cycling performance. The enhancement of electrochemical performance may be attributed to the faster kinetics of sodium ion sodiation/desodiation, which could be a result of enhanced electronic conductivity due to the formation of TiN thin layer coating.     

Influence of sol-gel precursors on the electrochemical performance of NaMn<Subscript>0.33</Subscript>Ni<Subscript>0.33</Subscript>Co<Subscript>0.33</Subscript>O<Subscript>2</Subscript> positive electrode for sodium-ion battery

Among the various cathode materials explored for sodium-ion batteries (SIBs), NaMn_0.33Ni_0.33Co_0.33O₂, with a layered oxide structure, is a promising material due to its high theoretical capacity (240 mAhg^?1). We have synthesized NaMn_0.33Ni_0.33Co_0.33O₂ using two different types of precursors, namely metal acetates and metal nitrates by the sol-gel method. XRD patterns confirm the formation of a stable phase of the material at 900 °C. Coupled TGA-FTIR analysis was used to optimize the calcination conditions and to understand the hydrolysis and condensation mechanism of the sol-gel precursors. FTIR spectra extracted at different temperatures reveal the polymer network-forming tendency of the acetate ligands whereas the polymerization is inhibited in the nitrate precursors. SEM analysis shows spherical and platelet morphologies of samples synthesized from nitrate and acetate precursors, respectively. Using in situ impedance and galvanostatic charge/discharge studies, we observed that the precursors used to synthesize the cathode material influence the electrochemical properties of the material, as in this case, where we observe a 20 % improvement in terms of capacity by using acetate precursors instead of nitrate precursors.     

Advanced LiTi<Subscript>2</Subscript>(PO<Subscript>4</Subscript>)<Subscript>3</Subscript>/C anode by incorporation of carbon nanotubes for aqueous lithium-ion batteries

Inferior rate capability is a big challenge for LiTi₂(PO₄)₃ anode for aqueous lithium-ion batteries. Herein, to address such issue, we synthesized a high-performance LiTi₂(PO₄)₃/carbon/carbon nanotube (LTP/C/CNT) composite by virtue of high-quality carbon coating and incorporation of good conductive network. The as-prepared LTP/C/CNT composite exhibits excellent rate performance with discharge capacity of 80.1 and 59.1 mAh g^?1 at 10 C and 20 C (based on the mass of anode, 1 C = 150 mA g^?1), much larger than that of the LTP/C composite (53.4 mAh g^?1 at 10 C, and 31.7 mAh g^?1 at 20 C). LTP/C/CNT also demonstrates outstanding cycling stability with capacity retention of 83.3 % after 1000 cycles at 5 C, superior to LTP/C without incorporation of CNTs (60.1 %). As verified, the excellent electrochemical performance of the LTP/C/CNT composite is attributed to the enhanced electrical conductivity, rapid charge transfer, and Li-ion diffusion because of the incorporation of CNTs.     

Hierarchical Co<Subscript>3</Subscript>O<Subscript>4</Subscript>@C hollow microspheres with high capacity as an anode material for lithium-ion batteries

Three-dimensional hierarchical Co₃O₄@C hollow microspheres (Co₃O₄@C HSs) are successfully fabricated by a facile and scalable method. The Co₃O₄@C HSs are composed of numerous Co₃O₄ nanoparticles uniformly coated by a thin layer of carbon. Due to its stable 3D hierarchical hollow structure and uniform carbon coating, the Co₃O₄@C HSs exhibit excellent electrochemical performance as an anode material for lithium-ion batteries (LIBs). The Co₃O₄@C HSs electrode delivers a high reversible specific capacity, excellent cycling stability (1672 mAh g^?1 after 100 cycles at 0.2 A g^?1 and 842.7 mAh g^?1 after 600 cycles at 1 A g^?1), and prominent rate performance (580.9 mAh g^?1 at 5 A g^?1). The excellent electrochemical performance makes this 3D hierarchical Co₃O₄@C HS a potential candidate for the anode materials of the next-generation LIBs. In addition, this simple synthetic strategy should also be applicable for synthesizing other 3D hierarchical metal oxide/C composites for energy storage and conversion.     

Improved electrochemical properties of YF<Subscript>3</Subscript>-coated Li<Subscript>1.2</Subscript>Mn<Subscript>0.54</Subscript>Ni<Subscript>0.13</Subscript>Co<Subscript>0.13</Subscript>O<Subscript>2</Subscript> as cathode for Li-ion batteries

Yttrium fluoride YF₃ layer with different coating contents is successfully covered on the surface of Li_1.2Mn_0.54Ni_0.13Co_0.13O₂ via a common wet chemical approach. The XRD, SEM, TEM, and charge-discharge tests are applied to investigate the influence of YF₃ layer on the micro-structural, morphology, and electrochemical properties of Li_1.2Mn_0.54Ni_0.13Co_0.13O₂. And the electrochemical test results demonstrate that the YF₃-coated LMNCO samples exhibit the improved electrochemical properties. The 2wt.%YF₃-coated LMNCO delivers a discharge capacity of 116.6 mAh g^?1 at 5 C rate, much larger than that (95.6 mAh g^?1) of the pristine one. Besides, the electrochemical impedance spectroscopy (EIS) and cyclic voltammetric results indicate that the YF₃ coating layer can promote the optimization formation of SEI film and reversibility of the electrochemical redox.     

Enhancement of electrochemical properties of Ca<Subscript>3</Subscript>Co<Subscript>4</Subscript>O<Subscript>9</Subscript> as anode materials for lithium-ion batteries by transition metal doping

Misfit-layered calcium cobaltites (Ca₃Co₄O₉, Ca₃Co_3.9Fe_0.1O₉, and Ca₃Co_3.9Mn_0.1O₉), as anode materials for lithium-ion batteries, were synthesized by a simple hydro-decomposition method. All synthesized samples do not show any impurity phase. They exhibited plate-like particle with the particle size of 1–2 μm. The specific capacities of doped samples showed higher electrochemical performance compared to the undoped sample. After charge/discharge of 50 cycles, the specific capacities of Ca₃Co₄O₉, Ca₃Co_3.9Fe_0.1O₉, and Ca₃Co_3.9Mn_0.1O₉ were 343, 562, and 581 mAh g^?1, respectively. The doped samples showed an increase of over 60% compared to the undoped sample. The cyclic voltammetry profile of the doped samples showed the enhanced reactivity corresponding to their improved electrochemical performance. The capacity improvement of doped samples resulted from the metal oxide/Li conversion reactions, volume change, and high reactivity.     

Thermoeletrochemical study on LiNi<Subscript>0.8</Subscript>Co<Subscript>0.1</Subscript>Mn<Subscript>0.1</Subscript>O<Subscript>2</Subscript> with in situ modification of Li<Subscript>2</Subscript>ZrO<Subscript>3</Subscript>

To improve the electrochemical performance of Nickel-rich cathode material LiNi_0.8Co_0.1Mn_0.1O₂, an in situ coating technique with Li₂ZrO₃ is successfully applied through wet chemical method, and the thermoelectrochemical properties of the coated material at different ambient temperatures and charge-discharge rates are investigated by electrochemical-calorimetric method. Cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) tests demonstrate that the Li₂ZrO₃ coating decreases the electrode polarizatoin and reduces the charge transfer resistance of the material during cycling. Moreover, it is found that with the ambient temperatures and charge-discharge rates increase, the specific capacity decreases, the amount of heat increases, and the enthalpy change (ΔH) increases. The specific capacity of the cells at 30 °C are 203.8, 197.4, 184.0, and 174.5 mAh g^?1 at 0.2, 0.5, 1.0, and 2.0 C, respectively. Under the same rate (2.0 C), the amounts of heat of the cells are 381.64, 645.32, and 710.34 mJ at 30, 40, and 50 °C. These results indicate that Li₂ZrO₃ coating plays an important role to enhance the electrochemical performance of LiNi_0.8Co_0.1Mn_0.1O₂ and reveal that choosing suitable temperature and current is critical for solving battery safety problem.     

CeO<Subscript>2</Subscript> and Nb<Subscript>2</Subscript>O<Subscript>5</Subscript> modified Ni-YSZ anode for solid oxide fuel cell

Ni sintering at high temperature (～ 800 °C) operation drastically degrades the performance of Ni-yttria-stabilized zirconia (YSZ) anode in solid oxide fuel cell (SOFC). Mixed ionic and electronic conductive oxides such as CeO₂ and Nb₂O₅ enhance the dispersion of Ni, CeO₂ enhances the redox behavior and promotes charge transfer reactions, and Nb₂O₅ increases the triple phase boundary. In the present work, anode-supported SOFC is fabricated and tested in H₂ fuel at 800 °C. YSZ and lanthanum strontium manganite (LSM)-YSZ are used as the electrolyte and composite cathode with NiO-YSZ, CeO₂-NiO-YSZ, and Nb₂O₅-NiO-YSZ as an anode. The peak power density obtained for the cell with 10% CeO₂–30% NiO-YSZ anode at the 5 and 25 h of operation is 330 and 290 mW cm^?2 which is higher than that for 40% NiO-YSZ anode (275 mW cm^?2 at 5 h). The peak power density obtained for the cell with 10% Nb₂O₅–30% NiO-YSZ anode at the 5 and 25 h of operation is 301 and 285 mW cm^?2 which is higher than that for 40% NiO-YSZ anode (275 mW cm^?2 at 5 h). Physical characterization has been carried to study morphology, elemental analysis, particle size, and phase formation of the fabricated anode before and after cell operation to correlate the cell performance.     

Synthesis of Li<Subscript>4</Subscript>Ti<Subscript>5</Subscript>O<Subscript>12</Subscript>-reduced graphene oxide composite and its application for hybrid supercapacitors

We describe in this paper the synthesis and the characterization of Li₄Ti₅O₁₂-reduced graphene oxide (LTO-RGO) composite and demonstrate their use as hybrid supercapacitor, which is consist of an LTO negative electrode and activate carbon (AC) positive electrode. The LTO-RGO composites were synthesized using a simple, one-step process, in which lithium sources and titanium sources were dissolved in a graphene oxide (GO) suspension and then thermal treated in N₂. The lithium-ion battery with LTO-RGO composite anode electrode revealed higher discharge capacity (167 mAh g^?1 at 0.2 C) and better capacity retention (67%) than the one with pure LTO. Meanwhile, compared with the AC//LTO supercapacitor, the AC//LTO-RGO hybrid supercapacitor exhibits higher energy density and power density. Results show that the LTO-RGO composite is a very promising anode material for hybrid supercapacitor.     

Effect of high-temperature crystallization on the electrochemical properties of LiNi<Subscript>0.5</Subscript>Co<Subscript>0.2</Subscript>Mn<Subscript>0.3</Subscript>O<Subscript>2</Subscript> synthesized from a lithiated transition metal oxide precursor

The lithiated transition metal oxide precursor (LNCMO) with typical α-NaFeO₂ structure and imperfect crystallinity, obtained from a hydrothermal process, was pretreated at 500 °C and then subjected to sintering at 800–920 °C to synthesize the ternary layered LiNi_0.5Co_0.2Mn_0.3O₂ (NCM523). X-ray diffraction (XRD), scanning electron microscope (SEM), cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS), and charge/discharge testing were used for investigating the effect of the high-temperature crystallization on the properties of the NCM523 cathode materials. The results show that the materials heated at 880–900 °C possess superior cation ordering, perfect crystallinity, and excellent electrochemical performances, among which the material heated at 900 °C delivers better performances, with the initial discharge capacity of 152.6 mAh g^?1 at 0.5 C over 3.0 to 4.3 V and the capacity retention of 95.5% after 50 cycles. Furthermore, the effect of the high-temperature crystallization on the Li⁺ diffusion coefficient, potential polarization, and electrochemical resistance are discussed.     

Performance and sulfur resistance of doped yttrium chromite-ceria composite as anode material for the SOFCs operating on H<Subscript>2</Subscript>S-containing fuel

The sulfur resistance and performance of Sr- and Mn-doped yttrium chromite (YSCM)-samaria-doped ceria (SDC) composite material were investigated for potential use as anodes in solid oxide fuel cells (SOFCs). The anode was well adhered to the electrolyte, which was ascribed to their similar coefficient of thermal expansion (TEC). The electro-catalytic activity of YSCM-SDC anodes in yttria-stabilized zirconia (YSZ) electrolyte-supported cells toward hydrogen oxidation was superior to that of the La_0.75Sr_0.25Cr_0.5Mn_0.5O_3-δ (LSCM) anode. Sr depletion in the YSCM structure and the formation of SrSO₄ in the presence of sulfur led to performance degradation of the anode. Irreversible and reversible performance degradation suggested that YSCM and SDC played a respective role during the anode deactivation process. The voltage decreased at a rate of 31 mV/h and stabilized at 0.49 V under a 3000 ppm H₂S atmosphere. In addition, the sulfur tolerance of YSCM-SDC anode was better than SDC under strictly identical conditions.     

CeO<Subscript>2</Subscript> coating to improve the performance of Li[Li<Subscript>0.2</Subscript>Mn<Subscript>0.54</Subscript>Ni<Subscript>0.13</Subscript>Co<Subscript>0.13</Subscript>]O<Subscript>2</Subscript>

The Li[Li_0.2Mn_0.54Ni_0.13Co_0.13]O₂ coated with CeO₂ has been fabricated by an ionic interfusion method. Both the bare and the CeO₂-coated samples have a typical layered structure with R-3m and C2/m space group. The results of XRD and TEM images display that the CeO₂ coating layer on the precursor could enhance the growth of electrochemically active surface planes ((010), (110), and (100) planes) in the following ionic interfusion process. The results of galvanostatic cycling tests demonstrate that the CeO₂-coated sample has a discharge capacity of 261.81 mAh g^?1 with an increased initial Coulombic efficiency from 62.4 to 69.1% at 0.05 °C compared with that of bare sample and delivers an improved capacity retention from 71.7 to 83.4% after 100 cycles at 1 °C (1 °C?=?250 mA g^?1). The results of electrochemical performances confirm that the surface modification sample exhibits less capacity fading, lower voltage decay, and less polarization.     

Low-temperature one-step solid-phase synthesis of carbon-encapsulated TiO<Subscript>2</Subscript> nanocrystals as anode materials for lithium-ion batteries

A simple and highly efficient method is developed for in situ one-step preparation of carbon co-encapsulated anatase and rutile TiO₂ nanocrystals (TiO₂@C) with core-shell structure for lithium-ion battery anode. The synthesis is depending on the solid-phase reaction of titanocene dichloride with ammonium persulfate in an autoclave at 200 °C for 30 min. The other three titanocene complexes including bis(cyclopentadienyl)dicarbonyl titanium, cyclopentadienyltitanium trichloride, and cyclopentadienyl(cycloheptatrienyl)titanium are used instead to comprehensively investigate the formation mechanism and to improve the microstructure of the product. The huge heat generated during the explosive reaction cleaves the cyclopentadiene ligands into small carbon fragments, which form carbon shell after oxidative dehydrogenation coating on the TiO₂ nanocrystals, resulting in the formation of core-shell structure. The TiO₂ nanocrystals prepared by titanocene dichloride have an equiaxed morphology with a small diameter of 10–55 nm and the median size is 30.3 nm. Hundreds of TiO₂ nanocrystals are encapsulated together by the worm-like carbon shell, which is amorphous and about 20–30 nm in thickness. The content of TiO₂ nanocrystals in the nanocomposite is about 31.1 wt.%. This TiO₂@C anode shows stable cyclability and retains a good reversible capacity of 400 mAh g^?1 after 100 cycles at a current density of about 100 mA g^?1, owing to the enhanced conductivity and protection of carbon shell.     

Modification research of LiAlO<Subscript>2</Subscript>-coated LiNi<Subscript>0.8</Subscript>Co<Subscript>0.1</Subscript>Mn<Subscript>0.1</Subscript>O<Subscript>2</Subscript> as a cathode material for lithium-ion battery

The LiNi_0.8Co_0.1Mn_0.1O₂ with LiAlO₂ coating was obtained by hydrolysis–hydrothermal method. The morphology of the composite was characterized by SEM, TEM, and EDS. The results showed that the LiAlO₂ layer was almost completely covered on the surface of particle, and the thickness of coating was about 8–12 nm. The LiAlO₂ coating suppressed side reaction between composite and electrolyte; thus, the electrochemical performance of the LiAlO₂-coated LiNi_0.8Co_0.1Mn_0.1O₂ was improved at 40 °C. The LiAlO₂-coated sample delivered a high discharge capacity of 181.2 mAh g^?1 (1 C) with 93.5% capacity retention after 100 cycles at room temperature and 87.4% capacity retention after 100 cycles at 40 °C. LiAlO₂-coated material exhibited an excellent cycling stability and thermal stability compared with the pristine material. These works will contribute to the battery structure optimization and design.     

Fabrication and electrochemical investigation of Li<Subscript>0.5</Subscript>TiO<Subscript>2</Subscript> as anode materials for lithium ion batteries

Hexagonal and cubic Li_0.5TiO₂ particles have been fabricated through magnesiothermic reduction of Li₂TiO₃ particles in a temperature range of 600 to 640 °C. The prolonged reduction time results in lattice transition from hexagonal to cubic structure of Li_0.5TiO₂. Their microstructures, valance state, chemical composition, as well as electrochemical performance as anode candidates for lithium ion batteries have been characterized and evaluated. The hexagonal Li_0.5TiO₂ exhibits better electrochemical activity compared with the cubic one. Further, the carbon-coated hexagonal Li_0.5TiO₂ displays improved electrochemical performance with initial reversible capacity of 176.6 mAh g^?1 and excellent cyclic behavior except capacity fading in the initial 10 cycles, which demonstrate a novel anode candidate for long lifetime lithium ion batteries.     

Titanium-modified Li<Subscript>4</Subscript>Ti<Subscript>5</Subscript>O<Subscript>12</Subscript> with a synergistic effect of surface modifying,bulk doping,and size reducing

In this work, a one-step solid-phase sintering process via TiO₂ and Li₂CO₃ under an argon atmosphere, with ultra-fine titanium powder as the modifying agent, was used to prepare a nano-sized Li₄Ti₅O₁₂/Ti composite (denoted as LTO–Ti) at 800 °C. The introduction of ultra-fine metal titanium powder played an important role. First, X-ray photoelectron spectroscopy demonstrates that Ti⁴⁺ was partially changed into Ti³⁺, through the reduction of the ultra-fine metal titanium powder. Second, X-ray diffraction revealed that the ultra-fine metal titanium powder did not react with the bulk structure of Li₄Ti₅O₁₂, while some pure titanium peaks could be seen. Additionally, the size of LTO–Ti particles could be significantly reduced from micro-scale to nano-scale. The structure and morphology of LTO–Ti were characterized by X-ray diffraction, X-ray photoelectron spectroscopy, Raman spectroscopy, scanning electron microscopy, and transmission electron microscopy. Electrochemical tests showed a charge/discharge current of 0.5, 1, 5, and 10 C; the discharge capacity of the LTO–Ti electrode was 170, 161, 140, and 111 mAh g^?1. It is believed that the designed LTO–Ti composite makes full use of both components, thus offering a large contact area between the electrolyte and electrode, high electrical conductivity, and lithium-ion diffusion coefficient during electrochemical processes. Furthermore, ultra-fine titanium powder, as the modifying agent, is amenable to large-scale production.     

Preparation and characterization of LiTi<Subscript>2</Subscript>O<Subscript>4</Subscript> anode material synthesized by one-step solid-state reaction

LiTi₂O₄ anode material for lithium-ion battery has been prepared by a novel one-step solid-state reaction method using Li₂CO₃, TiO₂, and carbon black as raw materials. X-ray diffraction, scanning electron microscopy, energy-dispersive spectrometry, and the determination of electrochemical properties show that the single phase of LiTi₂O₄ with spinel crystal structure is formed at 850?°C by this new method, and the lattice parameter is about 8.392?Å. The primary particle size of the LiTi₂O₄ powder is about 0.5–1.0 μm and its morphology is similar to a sphere. The lithium ion insertion voltage of LiTi₂O₄ anode material is about 1.50 V versus lithium metal, the initial discharge capacity is about 133.6 mAh g^-1, the charge–discharge voltage plateau is very flat, and no solid electrolyte interface film is formed when working potential is more than 1.0 V. The reaction reversibility and the cycling stability are excellent, and the high rate performance is good.     

Vinyl ethylene carbonate as an electrolyte additive for high-voltage LiNi<Subscript>0.4</Subscript>Mn<Subscript>0.4</Subscript>Co<Subscript>0.2</Subscript>O<Subscript>2</Subscript>/graphite Li-ion batteries

Vinyl ethylene carbonate (VEC) is investigated as an electrolyte additive to improve the electrochemical performance of LiNi_0.4Mn_0.4Co_0.2O₂/graphite lithium-ion battery at higher voltage operation (3.0–4.5 V) than the conventional voltage (3.0–4.25 V). In the voltage range of 3.0–4.5 V, it is shown that the performances of the cells with VEC-containing electrolyte are greatly improved than the cells without additive. With 2.0 wt.% VEC addition in the electrolyte, the capacity retention of the cell is increased from 62.5 to 74.5 % after 300 cycles. The effects of VEC on the cell performance are investigated by cyclic voltammetry(CV), electrochemical impedance spectroscopy(EIS), x-ray powder diffraction (XRD), energy dispersive x-ray spectrometry (EDS), scanning electron microscopy (SEM), and attenuated total reflectance-Fourier transform infrared (ATR-FTIR). The results show that the films electrochemically formed on both anode and cathode, derived from the in situ decomposition of VEC at the initial charge–discharge cycles, are the main reasons for the improved cell performance.     

Synthesis of free-standing MnO<Subscript>2</Subscript>/reduced graphene oxide membranes and electrochemical investigation of their performances as anode materials for half and full lithium-ion batteries

MnO₂ nanotubes/reduced graphene oxide (MnO₂/RGO) membranes with different MnO₂ contents are successfully synthesized by a facile two-step method including vacuum filtration and subsequent thermal reduction route. The MnO₂ nanotubes obtained are 38 nm in diameter and homogeneously imbedded in RGO sheets as spacers. The synthesized MnO₂/RGO membranes exhibit excellent mechanical flexibilities and free-standing properties. Using the membranes directly as anode materials for lithium batteries (LIBs), the membranes for half LIBs show superb cycling stabilities and rate performances. Importantly, the electrochemical performances of MnO₂/RGO membranes show a strong dependence on the MnO₂ nanotube contents in the hybrids. In addition, our results show that the hybrid membranes with 49.0 wt% MnO₂ nanotube in half LIBs achieve a high reversible capacity of 1006.7 mAh g^?1 after 100 cycles at a current density of 0.1 A g^?1, which is higher lithium storage capacity than that of reported MnO₂-carbon electrodes. Furthermore, the synthesized full cell (MnO₂/RGO//LiCoO₂) system also exhibit excellent electrochemical performances, which can be attributed to the unique microstructures of MnO₂ and GRO, coupled with the strong synergistic interaction between MnO₂ nanotubes and GRO sheets.     

Effect of passivating Al<Subscript>2</Subscript>O<Subscript>3</Subscript> thin films on MnO<Subscript>2</Subscript>/carbon nanotube composite lithium-ion battery anodes

MnO₂/carbon nanotube composite electrodes for Li-ion battery application were directly coated with ultrathin thicknesses of aluminum oxide film by atomic layer deposition (ALD). The non-reactive Al₂O₃ layer not only provides a stable film to protect the manganese oxide and carbon nanotubes from undesirable reaction with the electrolyte but also restrains the volume change strain of manganese oxide during cycling. The first cycle Coulombic efficiency of coated samples was increased to different extents depending on the coating thickness. In the following cycles, the coated electrodes denote high specific capacity, good capacity retention ability, and perfect rate charge/discharge performance.