Advanced LiTi<Subscript>2</Subscript>(PO<Subscript>4</Subscript>)<Subscript>3</Subscript>/C anode by incorporation of carbon nanotubes for aqueous lithium-ion batteries

Inferior rate capability is a big challenge for LiTi₂(PO₄)₃ anode for aqueous lithium-ion batteries. Herein, to address such issue, we synthesized a high-performance LiTi₂(PO₄)₃/carbon/carbon nanotube (LTP/C/CNT) composite by virtue of high-quality carbon coating and incorporation of good conductive network. The as-prepared LTP/C/CNT composite exhibits excellent rate performance with discharge capacity of 80.1 and 59.1 mAh g^?1 at 10 C and 20 C (based on the mass of anode, 1 C = 150 mA g^?1), much larger than that of the LTP/C composite (53.4 mAh g^?1 at 10 C, and 31.7 mAh g^?1 at 20 C). LTP/C/CNT also demonstrates outstanding cycling stability with capacity retention of 83.3 % after 1000 cycles at 5 C, superior to LTP/C without incorporation of CNTs (60.1 %). As verified, the excellent electrochemical performance of the LTP/C/CNT composite is attributed to the enhanced electrical conductivity, rapid charge transfer, and Li-ion diffusion because of the incorporation of CNTs.     

Preparation of Co<Subscript>3</Subscript>O<Subscript>4</Subscript> hollow microsphere/graphene/carbon nanotube flexible film as a binder-free anode material for lithium-ion batteries

A flexible Co₃O₄ hollow microsphere/graphene/carbon nanotube hybrid film is successfully prepared through a facile filtration strategy and a subsequent thermally treated process. The composition, morphology, and structure of the as-prepared film are characterized by X-ray diffraction, X-ray photoelectron spectrometer, scanning electron microscopy, and transmission electron microscopy. Based on the morphology characterizations on the hybrid film, the Co₃O₄ hollow microspheres are uniformly and closely attached on three-dimensional (3D) graphene/carbon nanotubes (GR/CNTs) network, which decreases the agglomeration of Co₃O₄ microspheres effectively. In this hybrid film, the 3D GR/CNT network which enhances conductance as well as prevents aggregation is a benefit to help Co₃O₄ to exert its lithium storage capabilities sufficiently. When used as a binder-free anode material for lithium-ion batteries, the hybrid film delivers excellent electrochemical properties involving reversible capacity (863 mAh g^?1 at a current density of 100 mA g^?1) and rate performance (185 mAh g^?1 at a current density of 1600 mA g^?1).     

Scalable synthesis and superior performance of TiO<Subscript>2</Subscript>-reduced graphene oxide composite anode for sodium-ion batteries

TiO₂-reduced graphene oxide (RGO) composite was synthesized via a sol-gel process and investigated as an anode material for sodium-ion batteries (SIBs). A remarkable improvement in sodium ion storage with a reversible capacity of 227 mAh g^?1 after 50 cycles at 50 mA g^?1 is achieved, compared to that (33 mAh g^?1) for TiO₂. The enhanced electrochemical performance of TiO₂-RGO composite is attributed to the larger specific surface area and better electrical conductivity of TiO₂-RGO composite. The excellent performance of TiO₂-RGO composite enables it a potential electrode material for SIBs.     

Fe<Subscript>3</Subscript>O<Subscript>4</Subscript> quantum dots on 3D-framed graphene aerogel as an advanced anode material in lithium-ion batteries

Three-dimensional fabricated Fe₃O₄ quantum dots/graphene aerogel materials (Fe₃O₄ QDs/GA) were obtained from a facile hydrothermal strategy, followed by a subsequently heat treatment process. The Fe₃O₄ QDs (2–5 nm) are anchored tightly and dispersed uniformly on the surface of three-dimensional GA. The as-prepared anode materials exhibit a high reversible capacity of 1078 mAh g^?1 at a current density of 100 mA g^?1 after 70 cycles in lithium-ion batteries (LIBs) system. Moreover, the rate capacity still remains 536 mAh g^?1 at 1000 mA g^?1. The enhanced electrochemical performance is attributed to that the GA not only acts as a three-dimensional electronic conductive matrix for the fast transportation of Li⁺ and electrons, but also provides with double protection against the aggregation and pulverization of Fe₃O₄ QDs during cycling. Apparently, the synergistic effects of the three-dimensional GA and the quantum dots are fully utilized. Therefore, the Fe₃O₄ QDs/GA composites are promising materials as advanced anode materials for LIBs.     

Electrochemical comparison of LiFe<Subscript>0.4</Subscript>Mn<Subscript>0.595</Subscript>Cr<Subscript>0.005</Subscript>PO<Subscript>4</Subscript>/C and LiMnPO<Subscript>4</Subscript>/C cathode materials

A comparison of electrochemical performance between LiFe_0.4Mn_0.595Cr_0.005PO₄/C and LiMnPO₄/C cathode materials was conducted in this paper. The cathode samples were synthesized by a nano-milling-assisted solid-state process using caramel as carbon sources. The prepared samples were investigated by XRD, SEM, TEM, energy-dispersive X-ray spectroscopy (EDAX), powder conductivity test (PCT), carbon-sulfur analysis, electrochemical impedance spectroscopy (EIS), and galvanostatic charge-discharge cycling. The results showed that LiFe_0.4Mn_0.595Cr_0.005PO₄/C exhibited high specific capacity and high energy density. The initial discharge capacity of LiFe_0.4Mn_0.595Cr_0.005PO₄/C was 163.6 mAh g^?1 at 0.1C (1C = 160 mA g^?1), compared to 112.3 mAh g^?1 for LiMnPO₄/C. Moreover, the Fe/Cr-substituted sample showed good cycle stability and rate performance. The capacity retention of LiFe_0.4Mn_0.595Cr_0.005PO₄/C was 98.84 % over 100 charge-discharge cycles, while it was only 86.64 % for the pristine LiMnPO₄/C. These results indicated that Fe/Cr substitution enhanced the electronic conductivity for the prepared sample and facilitated the Li⁺ diffusion in the structure. Furthermore, LiFe_0.4Mn_0.595Cr_0.005PO₄/C composite presented high energy density (606 Wh kg^?1) and high power density (574 W kg^?1), thus suggested great potential application in lithium ion batteries (LIBs).     

Improving the electrochemical performance of Li-rich Li<Subscript>1.2</Subscript>Ni<Subscript>0.13</Subscript>Co<Subscript>0.13</Subscript>Mn<Subscript>0.54</Subscript>O<Subscript>2</Subscript> cathode material by LiF coating

To suppress the capacity fade of Li-rich Li_1.2Ni_0.13Co_0.13Mn_0.54O₂ material as cathode materials for lithium-ion battery, we introduce a LiF coating layer on the surface to improve the cycling performance of Li_1.2Ni_0.13Co_0.13Mn_0.54O₂ material. The modified sample shows a capacity of 163.2 mAh g^?1 with a capacity retention of 95% after 100 cycles at a current density of 250 mA g^?1, while the pristine sample only delivers a capacity of 129.9 mAh g^?1 with a capacity retention of 82%. Compared with the pristine material, the LiF-modified sample exhibits an obvious enhancement in the electrochemical performance, which will be very beneficial for this material to be commercialized on the new energy vehicles and other related areas.     

Facial synthesis of carbon-coated ZnFe<Subscript>2</Subscript>O<Subscript>4</Subscript>/graphene and their enhanced lithium storage properties

Carbon-coated ZnFe₂O₄ spheres with sizes of ~110–180 nm anchored on graphene nanosheets (ZF@C/G) are successfully prepared and applied as anode materials for lithium ion batteries (LIBs). The obtained ZF@C/G presents an initial discharge capacity of 1235 mAh g^?1 and maintains a reversible capacity of 775 mAh g^?1 after 150 cycles at a current density of 500 mA g^?1. After being tested at 2 A g^?1 for 700 cycles, the capacity still retains 617 mAh g^?1. The enhanced electrochemical performances can be attributed to the synergetic role of graphene and uniform carbon coating (~3–6 nm), which can inhibit the volume expansion, prevent the pulverization/aggregation upon prolonged cycling, and facilitate the electron transfer between carbon-coated ZnFe₂O₄ spheres. The electrochemical results suggest that the synthesized ZF@C/G nanostructures are promising electrode materials for high-performance lithium ion batteries.

Open image in new window

Graphical abstract ?

     

Synthesis and lithium-ion storage performances of LiFe<Subscript>0.5</Subscript>Co<Subscript>0.5</Subscript>PO<Subscript>4</Subscript>/C nanoplatelets and nanorods

Carbon-coated olivine-structured LiFe_0.5Co_0.5PO₄ solid solution was synthesized by a facile rheological phase method and applied as cathode materials of lithium-ion batteries. The nanostructure’s properties, such as morphology, component, and crystal structure for the samples, characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), Brunauer, Emmett, and Teller (BET) determination, X-ray photoelectron spectroscopy (XPS), and the electrochemical performances were evaluated using constant current charge/discharge tests and electrochemical impedance spectroscopy (EIS). The results indicate that nanoplatelet- and nanorod-structured LiFe_0.5Co_0.5PO₄/C composites were separately obtained using stearic acid or polyethylene glycol 400 (PEG400) as carbon source, and the surfaces of particles for the two samples are ideally covered by full and uniform carbon layer, which is beneficial to improving the electrochemical behaviors. Electrochemical tests verify that the nanoplatelet LiFe_0.5Co_0.5PO₄/C shows a better capacity capability, delivering a discharge specific capacity of 133.8, 112.1, 98.3, and 74.4 mAh g^?1 at 0.1, 0.5, 1, and 5 C rate (1 C?=?150 mA g^?1); the corresponding cycle number is 5th, 11th, 15th, 20th, and 30th, respectively, whereas the nanorod one possesses more excellent cycling ability, with a discharge capacity of 83.3 mAh g^?1 and capacity retention of 86.9% still maintained after cycling for 100 cycles at 0.5 C. Results from the present study demonstrate that the LiFe_0.5Co_0.5PO₄ solid solution nanomaterials with favorable carbon coating effect combine the characteristics and advantage of LiFePO₄ and LiCoPO₄, thus displaying a tremendous potential as cathode of lithium-ion battery.     

Synthesis and electrochemical performance of carbon-coated LiCoBO<Subscript>3</Subscript> as cathode materials for lithium-ion batteries

Carbon-coated LiCoBO₃ (LiCoBO₃/C) is prepared by sol-gel method and polyethylene glycol 6000 (PEG-6000) is chosen as carbon source. The LiCoBO₃/C sample exhibits an initial discharge capacity of 76.7 mAh g^?1 at 0.1 C, and it can deliver a discharge capacity of 65.9 mAh g^?1 after 50 cycles, while the LiCoBO₃ sample only presents a first discharge capacity of 34.3 and 16.8 mAh g^?1 at the 50th cycle, LiCoBO₃/C sample shows better cycling performance than that of LiCoBO₃. The improved electrochemical properties could be mainly ascribed to the conductive carbon network and the reduced particle size of the LiCoBO₃ powders. Electrochemical impedance spectroscopy (EIS) results confirm that carbon coating decreases the charge transfer resistance and improve the electrochemical reaction kinetics.     

CeO<Subscript>2</Subscript> coating to improve the performance of Li[Li<Subscript>0.2</Subscript>Mn<Subscript>0.54</Subscript>Ni<Subscript>0.13</Subscript>Co<Subscript>0.13</Subscript>]O<Subscript>2</Subscript>

The Li[Li_0.2Mn_0.54Ni_0.13Co_0.13]O₂ coated with CeO₂ has been fabricated by an ionic interfusion method. Both the bare and the CeO₂-coated samples have a typical layered structure with R-3m and C2/m space group. The results of XRD and TEM images display that the CeO₂ coating layer on the precursor could enhance the growth of electrochemically active surface planes ((010), (110), and (100) planes) in the following ionic interfusion process. The results of galvanostatic cycling tests demonstrate that the CeO₂-coated sample has a discharge capacity of 261.81 mAh g^?1 with an increased initial Coulombic efficiency from 62.4 to 69.1% at 0.05 °C compared with that of bare sample and delivers an improved capacity retention from 71.7 to 83.4% after 100 cycles at 1 °C (1 °C?=?250 mA g^?1). The results of electrochemical performances confirm that the surface modification sample exhibits less capacity fading, lower voltage decay, and less polarization.     

Enhanced lithium storage performance of a self-assembled hierarchical porous Co<Subscript>3</Subscript>O<Subscript>4</Subscript>/VGCF hybrid high-capacity anode material for lithium-ion batteries

A Co₃O₄/vapor-grown carbon fiber (VGCF) hybrid material is prepared by a facile approach, namely, via liquid-phase carbonate precipitation followed by thermal decomposition of the precipitate at 380 °C for 2 h in argon gas flow. The material is characterized by X-ray diffraction, scanning electron microscopy, transmission electron microscopy, Brunauer-Emmett-Teller specific surface area analysis, and carbon elemental analysis. The Co₃O₄ in the hybrid material exhibits the morphology of porous submicron secondary particles which are self assembled from enormous cubic-phase crystalline Co₃O₄ nanograins. The electrochemical performance of the hybrid as a high-capacity conversion-type anode material for lithium-ion batteries is investigated by cyclic voltammetry, electrochemical impedance spectroscopy, and galvanostatic discharge/charge methods. The hybrid material demonstrates high specific capacity, good rate capability, and good long-term cyclability, which are far superior to those of the pristine Co₃O₄ material prepared under similar conditions. For example, the reversible charge capacities of the hybrid can reach 1100–1150 mAh g^?1 at a lower current density of 0.1 or 0.2 A g^?1 and remain 600 mAh g^?1 at the high current density of 5 A g^?1. After 300 cycles at 0.5 A g^?1, a high charge capacity of 850 mAh g^?1 is retained. The enhanced electrochemical performance is attributed to the incorporated VGCFs as well as the porous structure and the smaller nanograins of the Co₃O₄ active material.     

Preparation of carbon encapsulated Li<Subscript>4</Subscript>Ti<Subscript>5</Subscript>O<Subscript>12</Subscript> anode material for lithium ion battery through pre-coating method

Carbon encapsulated Li₄Ti₅O₁₂ (C/Li₄Ti₅O₁₂) anode material for lithium ion battery was prepared by using the pre-coat method of two steps, and the TiO₂ was pre coated before the reaction with Li₂CO₃. The structure and morphology of the resultant C/Li₄Ti₅O₁₂ materials were characterized by X-ray diffraction (XRD) and scanning microscopy (SEM). Electrochemical tests showed that at 0.1 C, the initial discharge capacity was 169.9 mAh g^?1, and the discharge capacity was 80 mAh g^?1 at 5 C. After 100 cycles at 2 C, the discharge specific capacity was 108.5 mAh g^?1. Compare with one step coating method, results showed the C/Li₄Ti₅O₁₂ prepared by pre-coat method can reduce the particle’s size and effectively improve the electrochemical performance.     

Improvement in rate capability of lithium-rich cathode material Li[Li<Subscript>0.2</Subscript>Ni<Subscript>0.13</Subscript>Co<Subscript>0.13</Subscript>Mn<Subscript>0.54</Subscript>]O<Subscript>2</Subscript> by Mo substitution

Lithium-rich cathode material Li[Li_0.2Ni_0.13Co_0.13Mn_0.54]O₂ doped with trace Mo is successfully synthesized by a sol-gel method. The X-ray diffraction patterns show that trace Mo substitution increases the inter-layer space of the material, of which is benefiting to lithium ion insertion/extraction among the electrode materials. The (CV) tests demonstrate the decrease of polarization, and on the other hand, the lithium ion diffusion coefficient (D _Li) of the modified material turns out to be larger, which indicates a faster electrochemical process. As a result, the Mo doped material possesses high rate performance and good cycling stability, and the initial discharge capacity reaches 149.3 mAh g^?1 at a current density of 5.0 °C, and the residual capacity is 144.0 mAh g^?1 after 50 cycles with capacity retention of 96.5 % in the potential range of 2.0–4.8 V at room temperature.     

Pr-modified Li<Subscript>4</Subscript>Ti<Subscript>5</Subscript>O<Subscript>12</Subscript> nanofibers as an anode material for lithium-ion batteries with outstanding cycling performance and rate performance

Pr-doped Li₄Ti₅O₁₂ in the form of Li_4?x/3Ti_5?2x/3Pr_xO₁₂ (x = 0, 0.01, 0.03, 0.05, and 0.07) was synthesized successfully by an electrospinning technique. ICP shows that the doped samples are closed to the targeted samples. XRD analysis demonstrates that traces of Pr³⁺ can enlarge the lattice parameter of Li₄Ti₅O₁₂ from 8.3403 to 8.3765 Å without changing the spinel structure. The increase of lattice parameter is beneficial to the intercalation and de-intercalation of lithium-ion. XPS results identify the existence form of Ti is mainly Ti⁴⁺ and Ti³⁺ in minor quantity in Li_4?x/3Ti_5?2x/3Pr_xO₁₂ (x = 0.05) samples due to the small amount of Pr³⁺. The transition from Ti⁴⁺ to Ti³⁺ is conducive to the electronic conductivity of Li₄Ti₅O₁₂. FESEM images show that all the nanofibers are well crystallized with a diameter of about 200 nm and distributed uniformly. The results of electrochemical measurement reveal that the 1D Li_4?x/3Ti_5?2x/3Pr_xO₁₂ (x = 0.05) nanofibers display enhanced high-rate capability and cycling stability compared with that of undoped nanofibers. The high-rate discharge capacity of the Li_4?x/3Ti_5?2x/3Pr_xO₁₂ (x = 0.05) samples is excellent (101.6 mAh g^?1 at 50 °C), which is about 58.48 % of the discharge capacity at 0.2 °C and 4.3 times than that of the bare Li₄Ti₅O₁₂ (23.5 mA g^?1). Even at 10 °C (1750 mA g^?1), the specific discharge capacity is still 112.8 mAh g^?1 after 1000 cycles (87.9 % of the initial discharge capacity). The results of cyclic voltammograms (CV) and electrochemical impedance spectroscopy (EIS) illustrate that the Pr-doped Li₄Ti₅O₁₂ electrodes possess better dynamic performance than the pure Li₄Ti₅O₁₂, further confirming the excellent electrochemical properties above.     

Hierarchical Co<Subscript>3</Subscript>O<Subscript>4</Subscript>@C hollow microspheres with high capacity as an anode material for lithium-ion batteries

Three-dimensional hierarchical Co₃O₄@C hollow microspheres (Co₃O₄@C HSs) are successfully fabricated by a facile and scalable method. The Co₃O₄@C HSs are composed of numerous Co₃O₄ nanoparticles uniformly coated by a thin layer of carbon. Due to its stable 3D hierarchical hollow structure and uniform carbon coating, the Co₃O₄@C HSs exhibit excellent electrochemical performance as an anode material for lithium-ion batteries (LIBs). The Co₃O₄@C HSs electrode delivers a high reversible specific capacity, excellent cycling stability (1672 mAh g^?1 after 100 cycles at 0.2 A g^?1 and 842.7 mAh g^?1 after 600 cycles at 1 A g^?1), and prominent rate performance (580.9 mAh g^?1 at 5 A g^?1). The excellent electrochemical performance makes this 3D hierarchical Co₃O₄@C HS a potential candidate for the anode materials of the next-generation LIBs. In addition, this simple synthetic strategy should also be applicable for synthesizing other 3D hierarchical metal oxide/C composites for energy storage and conversion.     

Synthesis and electrochemical properties of P2-Na<Subscript>2/3</Subscript>Ni<Subscript>1/3</Subscript>Mn<Subscript>2/3</Subscript>O<Subscript>2</Subscript>

The pure phase P2-Na_2/3Ni_1/3Mn_2/3O₂ was synthesized by a solid reaction process. The optimum calcination temperature was 850 °C. The as-prepared product delivered a capacity of 158 mAh g^?1 in the voltage range of 2–4.5 V, and there was a phase transition from P2 to O2 at about 4.2 V in the charge process. The P2 phase exhibited excellent intercalation behavior of Na ions. The reversible capacity is about 88.5 mAh g^?1 at 0.1 C in the voltage range of 2–4 V at room temperature. At an elevated temperature of 55 °C, it could remain as an excellent capacity retention at low current rates. The P2-Na_2/3Ni_1/3Mn_2/3O₂ is a potential cathode material for sodium-ion batteries.     

Hard carbon derived from corn straw piths as anode materials for sodium ion batteries

Hard carbon is considered as the most promising anode material for practical sodium ion batteries. Herein, we report biomass-derived hard carbon made from corn straw piths through a simple carbonization process. X-ray diffraction patterns and Raman spectra elucidated highly disordered structures, and high-resolution transmission electron microscopy confirmed that the hard carbons have many local ordered structures containing turbostratic nanodomains and more nanovoids surround the turbostratic nanodomains. The electrochemical performances of the hard carbons were systematically investigated in sodium ion batteries. By optimizing the carbonization temperature, the sample carbonized at 1400 °C (HC1400) exhibited high reversible capacity of 310 mAh g^?1 and good cycling stability; the capacity can still retain 274 mAh g^?1 after 100 cycles. More importantly, HC1400 can deliver reversible capacity of 206 mAh g^?1 with 79% retention rate after 700 cycles measured at a current density of 200 mA g^?1, which is much better than those in most previous reports. This study provides a way to develop inexpensive, renewable, and recyclable materials from biomasses towards next-generation energy storage applications.     

Sulfur/microporous carbon composites for Li-S battery

A commercial carbon black with microporous framework is used as carbon matrix to prepare sulfur/microporous carbon (S/MC) composites for the cathode of lithium sulfur (Li-S) battery. The S/MC composites with 50, 60, and 72 wt.% sulfur loading are prepared by a facile heat treatment method. Electrochemical performance of the as-prepared S/MC composites are measured by galvanostatic charge/discharge tests, cyclic voltammetry (CV), and electrochemical impedance spectroscopy (EIS), with carbonate-based electrolyte of 1.0 M LiPF₆/(PC-EC-DEC). The composite with 50 wt.% sulfur presents the optimized electrochemical performance, including the utilization of active sulfur, discharge capacity, and cycling stability. At the current density of 50 mA g^?1, it can demonstrate a high initial discharge capacity of 1624.5 mAh g^?1. Even at the current density of 800 mA g^?1, the initial capacity of 1288.6 mAh g^?1 can be obtained, and the capacity can still maintain at 522.8 mAh g^?1 after 180 cycles. The remarkably improved electrochemical performance of the S/MC composite with 50 wt.% sulfur are attributed to the carbon matrix with microporous structure, which can effectively enhance the electrical conductivity of the sulfur cathode, suppress the loss of active material during charge/discharge processes, and restrain the migration of polysulfide ions to the lithium anode.     

Acacia gum-assisted co-precipitating synthesis of LiNi<Subscript>0.5</Subscript>Co<Subscript>0.2</Subscript>Mn<Subscript>0.3</Subscript>O<Subscript>2</Subscript> cathode material for lithium ion batteries

LiNi_0.5Co_0.2Mn_0.3O₂ particles of uniform size were prepared through carbonate co-precipitation method with acacia gum. The precursor of carbonate mixture was calcined at 800 °C, and a well-crystallized Ni-rich layered oxide was got. The phase structure and morphology were characterized by X-ray diffraction (XRD), field emission scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The micro-sized particles delivered high initial discharge capacity of 164.3 mA h g^?1 at 0.5 C (1 C?=?200 mA g^?1) between 2.5 and 4.3 V with capacity retention of 87.5 % after 100 cycles. High reversible discharge capacities of 172.4 and 131.4 mA h g^?1 were obtained at current density of 0.1 and 5 C, respectively. Cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) were performed to further study the LiNi_0.5Co_0.2Mn_0.3O₂ particles. Anyway, the excellent electrochemical performances of LiNi_0.5Co_0.2Mn_0.3O₂ sample should be attributed to the use of acacia gum.     

Nitrogen-doped carbon nanofiber decorated LiFePO<Subscript>4</Subscript> composites with superior performance for lithium-ion batteries

Nitrogen-doped carbon nanofiber (NCNF) decorated LiFePO₄ (LFP) composites are synthesized via an in situ hydrothermal growth method. Electrochemical performance results show that the embedded NCNF can improve electron and ion transfer, thereby resulting in excellent cycling performance. The as-prepared LFP and NCNF composites exhibit excellent electrochemical properties with discharge capacities of 188.9 mAh g^?1 (at 0.2 C) maintained at 167.9 mAh g^?1 even after 200 charge/discharge cycles. The electrode also presents a good rate capability of 10 C and a reversible specific capacity as high as 95.7 mAh g^?1. LFP composites are a potential alternative high-performing anode material for lithium ion batteries.