Influence of co-precipitation temperature on microstructure and electrochemical properties of Li[Li<Subscript>0.2</Subscript>Mn<Subscript>0.54</Subscript>Ni<Subscript>0.13</Subscript>Co<Subscript>0.13</Subscript>]O<Subscript>2</Subscript> cathode materials for lithium ion batteries

The layered Li-rich Mn-based cathode materials Li[Li_0.2Mn_0.54Ni_0.13Co_0.13]O₂ were prepared by using co-precipitation technique at different temperatures, and their crystal microstructure and particle morphology were observed and analyzed by XRD and SEM. The electrochemical properties of these samples were investigated by using charge-discharge tests, electrochemical impedance spectroscopy (EIS), and cyclic voltammetry (CV), respectively. The results indicated that all samples are of high purity. When the precursors were co-precipitated at 50 °C, their cathode materials have the most uniform and full particles and exhibit the highest initial discharge capacity (289.4 mAh/g at 0.1C), the best cycle stability (capacity retention rate of 91.2 % after 100 cycles at 0.5C), and the best rate performance. The EIS results show that the lower charge transfer resistance of 50 °C sample is responsible for its superior discharge capacity and rate performance.     

Improving the electrochemical performance of Li-rich Li<Subscript>1.2</Subscript>Ni<Subscript>0.13</Subscript>Co<Subscript>0.13</Subscript>Mn<Subscript>0.54</Subscript>O<Subscript>2</Subscript> cathode material by LiF coating

To suppress the capacity fade of Li-rich Li_1.2Ni_0.13Co_0.13Mn_0.54O₂ material as cathode materials for lithium-ion battery, we introduce a LiF coating layer on the surface to improve the cycling performance of Li_1.2Ni_0.13Co_0.13Mn_0.54O₂ material. The modified sample shows a capacity of 163.2 mAh g^?1 with a capacity retention of 95% after 100 cycles at a current density of 250 mA g^?1, while the pristine sample only delivers a capacity of 129.9 mAh g^?1 with a capacity retention of 82%. Compared with the pristine material, the LiF-modified sample exhibits an obvious enhancement in the electrochemical performance, which will be very beneficial for this material to be commercialized on the new energy vehicles and other related areas.     

Improved electrochemical properties of YF<Subscript>3</Subscript>-coated Li<Subscript>1.2</Subscript>Mn<Subscript>0.54</Subscript>Ni<Subscript>0.13</Subscript>Co<Subscript>0.13</Subscript>O<Subscript>2</Subscript> as cathode for Li-ion batteries

Yttrium fluoride YF₃ layer with different coating contents is successfully covered on the surface of Li_1.2Mn_0.54Ni_0.13Co_0.13O₂ via a common wet chemical approach. The XRD, SEM, TEM, and charge-discharge tests are applied to investigate the influence of YF₃ layer on the micro-structural, morphology, and electrochemical properties of Li_1.2Mn_0.54Ni_0.13Co_0.13O₂. And the electrochemical test results demonstrate that the YF₃-coated LMNCO samples exhibit the improved electrochemical properties. The 2wt.%YF₃-coated LMNCO delivers a discharge capacity of 116.6 mAh g^?1 at 5 C rate, much larger than that (95.6 mAh g^?1) of the pristine one. Besides, the electrochemical impedance spectroscopy (EIS) and cyclic voltammetric results indicate that the YF₃ coating layer can promote the optimization formation of SEI film and reversibility of the electrochemical redox.     

Combination of Fe-Mn based Li-rich cathode materials and conducting-polymer polypyrrole nanowires with high rate capability

The polypyrrole (PPy) nanowires are conducting 1D materials, which can significantly improve the electrical conductivity of the composites. A novel Li_1.26Fe_0.22Mn_0.52O₂ (LFMO) @ PPy nanowire composites were synthesized by simply ultrasonic dispersing LFMO and PPy nanowires in aqueous ethanol. The structure and morphology of pristine LFMO and LFMO@PPy are investigated by XRD, SEM, and TEM. The elemental mapping and FTIR results demonstrate the conductive network of PPy nanowires exists in the composites and the LFMO particles uniformly distribute on the PPy nanowires. LFMO combined with PPy nanowires exhibits better rate capability, higher capacity, coulombic efficiency, and cycleability than the pristine. The rate performance of composites with 10 wt% PPy nanowires shows the discharge capacities of 132.2 mAh/g and 98 mAh/g at 1C and 3C rate after 50 cycles, respectively. Electrochemical impedance spectroscopy test suggests that the conductive PPy nanowires can significantly decrease the charge-transfer resistance of LFMO. The composite with 10 wt% PPy nanowires shows a discharge capacity retention of 71% after 50 cycles at 1C, while the pristine sample only has 50% capacity retention.     

Synthesis and electrochemical properties of Li<Subscript>1.2</Subscript>Mn<Subscript>0.54</Subscript>Ni<Subscript>0.13</Subscript>Co<Subscript>0.13</Subscript>O<Subscript>2</Subscript> cathode material for lithium-ion battery

The layered Li_1.2Mn_0.54Ni_0.13Co_0.13O₂ lithium-rich manganese-based solid solution cathode material has been synthesized by a simple solid-state method. The as-prepared material has a typical layered structure with R-3m and C2/m space group. The synthesized Li_1.2Mn_0.54Ni_0.13Co_0.13O₂ has an irregular shape with the size range from 200 to 500 nm, and the primary particle of Li_1.2Mn_0.54Ni_0.13Co_0.13O₂ has regular sphere morphology with a diameter of 320 nm. Electrochemical performances also have been investigated. The results show that the cathode material Li_1.2Mn_0.54Ni_0.13Co_0.13O₂ prepared at 900 °C for 12 h has a good electrochemical performance, which can deliver a high initial discharge capacity of 233.5, 214.2, 199.3, and 168.1 mAh g^?1 at 0.1, 0.2, 0.5, and 1 C, respectively. After 50 cycles, the capacity retains 178.0, 166.3, 162.1, and 155.9 mAh g^?1 at 0.1, 0.2, 0.5, and 1 C, respectively. The results indicate that the simple method has a great potential in synthesizing manganese-based cathode materials for Li-ion batteries.     

Effect of high-temperature crystallization on the electrochemical properties of LiNi<Subscript>0.5</Subscript>Co<Subscript>0.2</Subscript>Mn<Subscript>0.3</Subscript>O<Subscript>2</Subscript> synthesized from a lithiated transition metal oxide precursor

The lithiated transition metal oxide precursor (LNCMO) with typical α-NaFeO₂ structure and imperfect crystallinity, obtained from a hydrothermal process, was pretreated at 500 °C and then subjected to sintering at 800–920 °C to synthesize the ternary layered LiNi_0.5Co_0.2Mn_0.3O₂ (NCM523). X-ray diffraction (XRD), scanning electron microscope (SEM), cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS), and charge/discharge testing were used for investigating the effect of the high-temperature crystallization on the properties of the NCM523 cathode materials. The results show that the materials heated at 880–900 °C possess superior cation ordering, perfect crystallinity, and excellent electrochemical performances, among which the material heated at 900 °C delivers better performances, with the initial discharge capacity of 152.6 mAh g^?1 at 0.5 C over 3.0 to 4.3 V and the capacity retention of 95.5% after 50 cycles. Furthermore, the effect of the high-temperature crystallization on the Li⁺ diffusion coefficient, potential polarization, and electrochemical resistance are discussed.     

A carbothermal reduction method for enhancing the electrochemical performance of LiFePO4/C composite cathode materials

LiFePO₄/C composite cathode material has been synthesized by a carbothermal reduction method using β-FeOOH nanorods as raw materials and glucose as both reducing agent and carbon source. The results indicate that the content of carbon and the morphology of raw material have effect on the electrochemical performance of the final LiFePO₄/C material. Sample LFP14 with a carbon content of 2.79 wt.% can deliver discharge capacities of 158.8, 144.3, 111.0, and 92.9 mAh g^?1 at 0.1, 1, 10, and 15 C, respectively. When decreasing the current from 15 C back to 0.1 C, a discharge capacity of 157.5 mAh g^?1 is recovered, which is 99.2 % of its initial capacity. Therefore, as a kind of cathode material for lithium ion batteries, this LiFePO₄/C material synthesized via a carbothermal reduction method is promising in large-scale production, and has potential application in upcoming hybrid electric vehicles or electric vehicles.     

Oxalate precursor preparation of Li1.2Ni0.13Co0.13Mn0.54O2 for lithium ion battery positive electrode

Li_1.2Ni_0.13Co_0.13Mn_0.54O₂ powders have been prepared through co-precipitation of metal oxalate precursor and subsequent solid state reaction with lithium carbonate. X-ray diffraction pattern shows that the massive rock-like structure has a good layered structure and solid solution characteristic. Scanning electron microscope and transition electron microscope images reveal that the Li_1.2Ni_0.13Co_0.13Mn_0.54O₂ composed of nanoparticles have the size of 1–2 μm. As a lithium ion battery positive electrode, the Li_1.2Ni_0.13Co_0.13Mn_0.54O₂ has an initial discharge capacity of 285.2 mAh g^?1 at 0.1 C within 2.0–4.8 V. When the cutoff voltage is decreased to 4.6 V, the cycling stability of product can be greatly improved, and a discharge capacity of 178.5 mAh g^?1 could be retained at 0.5 C after 100 cycles. At a high charge–discharge rate of 5 C (1,000 mAh g^?1), a stable discharge capacity of 121.4 mAh g^?1 also can be reached. As the experimental results, the Li_1.2Ni_0.13Co_0.13Mn_0.54O₂ prepared from oxalate precursor route is suitable as lithium ion battery positive electrode.     

Enhanced electrochemical performance of lithium ion battery cathode Li<Subscript>3</Subscript>V<Subscript>2</Subscript>(PO<Subscript>4</Subscript>)<Subscript>3</Subscript>/C

Li-ion battery cathode material lithium-vanadium-phosphate Li₃V₂(PO₄)₃ was synthesized by a carbon-thermal reduction method, using stearic acid, LiH₂PO₄, and V₂O₅ as raw materials. And stearic acid acted as reductant, carbon source, and surface active agent. The effect of its content on the crystal structure and electrochemical performance of Li₃V₂(PO₄)₃/C were characterized by XRD and electrochemical performance testing, respectively. The results showed that the content of carbon source has no significant effect on the crystal structure of lithium vanadium phosphate. Lihtium vanadium phosphate obtained with 12.3% stearic acid demonstrated the best electrochemical properties with a typical discharge capacity of 119.4 mAh/g at 0.1 C and capacity retention behavior of 98.5% after 50 cycles. And it has high reversible discharge capacity of 83 mAh/g at 5 C with the voltage window of 3 to 4.3 V.     

An investigation on the performance of LiFePO4/C derived from various FePO4

LiFePO₄/C composites were synthesized by carbothermal reduction method using commercial FePO₄ and Tween#80-assisted synthesized nano-FePO₄ as starting materials, glucose as reducing agent, and also carbon source. The FePO₄ intermediates were characterized by X-ray diffraction and scanning electron microscopy. A suitable mole ratio of Li to Fe was investigated, and the performances of samples synthesized under different temperatures were studied. It seems that the residual carbon content, which determine the electrochemical polarization of the cathode composites, greatly depend on the synthesis temperature when carbothermal reduction method was used. The electrochemical measurements showed that the discharge capacity first increase and then decrease with the rise of temperature. The optimal sample synthesized at 600 °C for 10 h using homemade FePO₄ as iron source exhibit 142 mAh?g^?1 at 0.2 C and a capacity retention rate of 98.8 % after 50 cycles.     

Synthesis of Li(Ni<Subscript>0.6</Subscript>Co<Subscript>0.2</Subscript>Mn<Subscript>0.2</Subscript>)O<Subscript>2</Subscript> with sodium DL-lactate as an eco-friendly chelating agent and its electrochemical performances for lithium-ion batteries

(Ni_0.6Co_0.2Mn_0.2)(OH)₂ precursor has been successfully prepared using hydroxide co-precipitation method. The thermodynamic model of hydroxide co-precipitation with sodium DL-lactate as an eco-friendly chelating agent is proposed. The microstructures of (Ni_0.6Co_0.2Mn_0.2)(OH)₂ precursors and Li(Ni_0.6Co_0.2Mn_0.2)O₂ cathode materials are investigated using X-ray diffractometer and scanning electronic microscopy, while the electrochemical performances of Li(Ni_0.6Co_0.2Mn_0.2)O₂ cathode materials are measured using a charge–discharge test. The influences of pH value on the structure and morphological and electrochemical performances of Li(Ni_0.6Co_0.2Mn_0.2)O₂ cathode materials have been discussed in detail. The results show that the sample at pH?=?11.5 exhibits the best lamellar structure and lowest cation mixing, while the sample at pH?=?11.0 delivers the most uniform and full particles and possesses the highest initial charge–discharge performance of 183.4 mAh/g and the best coulombic efficiency of 77.9% at the voltage range of 3.0–4.3 V. Even after 100 cycles, its discharge capacity still remains 165.2 mAh/g with the best retention rate of 90.1%. Furthermore, the sample at pH?=?11.0 delivers the highest discharge capacity at each current density. Even if discharged at 5C (1000 mA/g), the capacity of 115.6 mAh/g has been achieved. The sample at pH?=?11.0 exhibits the highest Li-ion diffusion coefficients (2.072?×?10^?12 cm²/s).     

Synthesis of sea urchin-like LiMn2O4 hollow macrospheres via in situ conversion for rechargeable lithium-ion batteries

Among several materials (transition metal oxide) under development for use as a cathode in lithium-ion batteries, cubic spinel LiMn₂O₄ is one of the most promising cathode materials. In this study, the sea urchin-like LiMn₂O₄ hollow macrospheres were synthesized by using sea urchin-like α-MnO₂ precursors through solid-state in situ self-sacrificing conversion route. The as-prepared LiMn₂O₄ was assembled by many single-crystalline “thorns” of ca.10–20 nm in diameter and ca. 400–500 nm in length. Galvanostatic battery testing showed that sea urchin-like LiMn₂O₄ had an initial discharge capacity of 126.8 mAh/g at the rate of 0.2 C in the potential range between 3.0 and 4.5 V. More than 96.67 % of the initial discharge capacity was maintained for over 50 cycles. The improved electrochemical properties were attributed to the reduced particle size and enhanced electrical contacts by the materials. This particular sea urchin-like structured composite conceptually provides a new strategy for designing electrodes in energy storage applications.     

Vertically aligned α-MnO<Subscript>2</Subscript> nanosheets on carbon nanotubes as cathodic materials for aqueous rechargeable magnesium ion battery

In this work, vertically aligned α-MnO₂ nanosheets on carbon nanotubes are synthesized simply by a solution process and the electrochemical performance as host materials of magnesium ion is tested in aqueous solution. Cyclic voltammetry analysis confirms the enhanced electrochemical activity of carbon nanotube-supported samples. Moreover, carbon nanotubes skeleton could reduce the charge transfer resistant of the cathode materials, which is confirmed by electrochemical impedance spectroscopy. Furthermore, when tested as magnesium ion batteries cathodic electrode, the α-MnO₂/carbon nanotube sample registers a prominent discharge capacity of 144.6 mAh g^?1 at current density of 0.5 A g^?1, which is higher than the discharge capacity of α-MnO₂ (87.5 mAh g^?1) due to the synergistic effect of insertion/deinsertion reaction and physical adsorption/desorption process. After the 1000th cycle, a remarkable discharge capacity of 48.3 mAh g^?1 is collected for α-MnO₂/carbon nanotube at current density of 10 A g^?1, which is 85% of the original. It is found that the carbon skeleton not only improved the capacity but also enhanced the cycling performance of the α-MnO₂ electrode significantly. Therefore, α-MnO₂/carbon nanotube is a very promising candidate for further application in environmentally benign magnesium ion batteries.     

Improvement in rate capability of lithium-rich cathode material Li[Li<Subscript>0.2</Subscript>Ni<Subscript>0.13</Subscript>Co<Subscript>0.13</Subscript>Mn<Subscript>0.54</Subscript>]O<Subscript>2</Subscript> by Mo substitution

Lithium-rich cathode material Li[Li_0.2Ni_0.13Co_0.13Mn_0.54]O₂ doped with trace Mo is successfully synthesized by a sol-gel method. The X-ray diffraction patterns show that trace Mo substitution increases the inter-layer space of the material, of which is benefiting to lithium ion insertion/extraction among the electrode materials. The (CV) tests demonstrate the decrease of polarization, and on the other hand, the lithium ion diffusion coefficient (D _Li) of the modified material turns out to be larger, which indicates a faster electrochemical process. As a result, the Mo doped material possesses high rate performance and good cycling stability, and the initial discharge capacity reaches 149.3 mAh g^?1 at a current density of 5.0 °C, and the residual capacity is 144.0 mAh g^?1 after 50 cycles with capacity retention of 96.5 % in the potential range of 2.0–4.8 V at room temperature.     

Effects of doping Al on the structure and electrochemical performances of Li[Li<Subscript>0.2</Subscript>Mn<Subscript>0.54</Subscript>Ni<Subscript>0.13</Subscript>Co<Subscript>0.13</Subscript>]O<Subscript>2</Subscript> cathode materials

The Li-rich cathode material Li[Li_0.2Mn_0.54Ni_0.13Co_0.13]O₂ had been successfully synthesized by a carbonate coprecipitation method. The effects of substituting traces of Al element for different transitional metal elements on the crystal structure and surface morphology had been investigated by X-ray diffraction (XRD) and field emission scanning electron microscopy. The results revealed that all the materials showed similar XRD patterns and surface morphology. It was demonstrated that LNCMAl1 exhibited the superior electrochemical performance. The discharge capacity was 265.2 mAh g^?1 at 0.1 C and still maintained a discharge capacity of 135.6 mAh g^?1 at 5.0 C. The capacity retention could still be 58.2 and 66.8% after 50 cycles at 1.0 and 2.0 C, respectively. Electrochemical impedance spectra results proved that the remarkably improved rate capability and cycling performance could be ascribed to the low charge transfer resistance and enhanced reaction kinetics.     

Synthesis of PANI/rGO composite as a cathode material for rechargeable lithium-polymer cells

Graphene oxide (GO) was synthesized by an improved Hummers method and then reduced with NaBH₄; GO became rGO with regular layered structure. Polyaniline (PANI)/rGO composite was prepared by a adsorption double oxidant method with rGO as a template. Some physical characterization methods (Fourier transform infrared spectroscopy analysis, X-ray diffraction, scanning electron microscope, and transmission electron microscope) were used to analyze the morphology and crystallinity of the composite. The electrochemical properties were characterized by cyclic voltammetry, impedance spectroscopy, galvanostatic charge/discharge, and rate capability. The first discharge specific capacity of the rPANI/rGO and PANI/rGO was 181.2 and 147.8 mAh/g. After 100 cycles, the capacity retention rate was still 90.2 and 88.9% separately, and the coulombic efficiency of batteries is close to 100%. These results demonstrate the composite has exciting potentials for the cathode material of lithium-ion battery.     

Synthesis of spinel LiNi<Subscript>0.5</Subscript>Mn<Subscript>1.5</Subscript>O<Subscript>4</Subscript> as advanced cathode via a modified oxalate co-precipitation method

Spinel-type LiNi_0.5Mn_1.5O₄ (LNMO) cathode materials for lithium ion batteries have been synthesized via a modified oxalate co-precipitation method. By virtue of the co-precipitation of Li⁺ with transition metal ions, the target materials can be obtained through one-pot reaction without subsequent mixing with lithium salts. What’s more, a uniform distribution between the lithium and transition metal ions at molecular level could be realized, which is beneficial for final electrochemical performances. The physical and electrochemical properties of the material are characterized by XRD, TGA, EDS, FT-IR, SEM, CV, EIS, and charge/discharge tests. The results prove that the as-prepared material owns a cubic spinel structure with a space group of Fd-3m, high crystallinity, uniform particle size, and excellent electrochemical performances. A higher initial capacity and superior rate performance are delivered compared with that of material by conventional co-precipitation method. High capacities of 131.7 and 104.0 mAh g^?1 could be displayed at 0.5 and 10 C, respectively. Excellent cycle stability is also demonstrated with more than 98.5 % capacity retention after 100 cycles at 1 C.     

The synthesis, structure, and electrochemical properties of a novel rods-shaped Li6V10O28 for lithium-ion batteries

Rods-shaped Li₆V₁₀O₂₈ powders were synthesized by rheological phase reaction. The ratio of the Li/V of the product sintered at 600 °C for 8 h was characterized by inductively coupled plasma. The structure, composite, and morphology of the product have been investigated by X-ray diffraction, scan electron microscope, transmission electron microscopy, and X-ray photoelectron spectrometry, respectively. After charge–discharge test using the product as the cathode material of lithium-ion batteries, the product calcined at 600 °C for 8 h exhibited an initial high discharge specific capacity of 212.4 mAh/g at a rate of 1.0 mA/cm² in a potential range of 2.0 and 4.4 V, and its stabilized capacity still remained 167.7 mAh/g after 30 cycles, which indicates that the rods-shaped Li₆V₁₀O₂₈ are promising cathode materials in lithium-ion batteries.     

Electrochemical properties of Li<Subscript>3</Subscript>V<Subscript>2</Subscript>(PO<Subscript>4</Subscript>)<Subscript>3</Subscript>/C cathode materials synthesized via ethylene glycol-assisted solvothermal method

The Li₃V₂(PO₄)₃/C (LVP/C) cathode materials for lithium-ion batteries were synthesized via ethylene glycol-assisted solvothermal method. The phase composition, phase transition temperature, morphology, and fined microstructure were studied using X-ray diffraction (XRD), differential thermal analyzer (DTA), scanning electron microscope (SEM), and transmission electron microscope (TEM), respectively. The electrochemical properties, impedance, and electrical conductivity of LVP/C cathode materials were tested by channel battery analyzer, the electrochemical workstation, and the Hall test system, respectively. The results shown that the appropriate amount of water added to ethylene glycol solvent contributes to the synthesis of pure phase LVP. The LVP₁₀/C cathode material can exhibit discharge capacities of 128, 126, 126, 123, 124, and 114 mAh g^?1 at 0.1, 0.5, 2, 5, 10, and 20 C in the voltage range of 3.0–4.3 V, respectively. Meanwhile, it shows also a stable cycling performance with the capacity retention of 89.6% after 180 cycles at 20 C.     

Synthesis and electrochemical performance of spherical LiNi<Subscript>0.8</Subscript>Co<Subscript>0.15</Subscript>Ti<Subscript>0.05</Subscript>O<Subscript>2</Subscript> cathode materials with high tap density

A series of spherical LiNi_0.8Co_0.15Ti_0.05O₂ cathode materials were synthesized through co-oxidation-controlled crystallization method followed by solid-state reaction at different calcination temperatures under oxygen flowing. The crystal structure and particles morphology of the as-prepared powders were characterized by X-ray diffraction (XRD) and scanning electron microscopy (SEM), respectively. All samples correspond to the layered α-NaFeO₂ structure with R-3m space group. The LiNi_0.8Co_0.15Ti_0.05O₂ prepared at 800 °C presents a better hexagonal ordering structure and better spherical particles and possesses a high tap density of 3.22 g cm^?3. Meanwhile, the NCT-2 sample exhibits an advanced electrochemical performance with an initial discharge capacity of 174.2 mAh g^?1 and capacity retention of 86.7 % after 30 cycles at 0.2 C.