用氧化偶联聚合法合成新型电活性聚酰胺及其结构表征

使用氧化偶联聚合的方法, 合成了一种新的电活性聚酰胺, 使其同时具有聚酰胺和聚苯胺性质. 该反应操作简便易行, 室温下即可进行. 通过红外光谱和核磁共振谱对其结构进行了表征, 用紫外-可见光谱和循环伏安法研究了氧化还原性质和电活性, 并测试了导电率.     

Effects of ultra-high pressures (>3.6 GPa) on the electrical resistance of polyaniline by in situ FT-IR studies

Electrical resistance measurements and FT-IR spectroscopy of polyaniline were studied in situ under ultra-high pressures generated by a diamond anvil cell (DAC). The electrical resistance of polyaniline decreased as the pressure increased, exhibiting polaron conductor characteristics. Minimum electrical resistance was observed at 3.6 GPa, about three orders of magnitude smaller than that at 1.0 GPa. Changes in electrical resistance were reversible when the pressure was below 3.6 GPa. In situ FT-IR results showed that irreversible chemical changes of the quinoid units in polyaniline molecular chains took place when the pressure exceeded 3.6 GPa, giving rise to a huge increase in electrical resistance.     

β-萘磺酸掺杂聚苯胺纳米粒子的固相反应法制备及其表征

利用固相反应法制备了 β 萘磺酸掺杂的聚苯胺纳米粒子 ,并以红外光谱 (FTIR) ,扫描电子显微镜(SEM) ,透射电镜 (TEM) ,X 射线衍射 (XRD)以及粉末微电极等测试方法对其进行了表征 .结果表明 ,固相反应法合成的 β 萘磺酸掺杂聚苯胺粒子直径为 30～ 5 0nm ,聚苯胺分子链排列有序 ,晶化率较好 .粉末微电极的循环伏安测试表明 ,β 萘磺酸掺杂聚苯胺有较好的电化学活性 .     

Thermal transporting properties of electrically conductive polyaniline films as organic thermoelectric materials

Thermal transporting properties of electrically conductive polyaniline films were first investigated in wide range of temperatures above room temperature as organic thermoelectric materials. Thermal conductivities of various protonic acid-doped polyaniline films were measured by combination of a laser flash method and a differential scanning calorimeter in relation with electrical conductivity and a kind of dopant. The thermal conductivities thus measured are in the range of conventional organic polymers, indicating that the doped polyaniline films have extremely low thermal conductivities among electrically conductive materials, and have correlation with neither electrical conductivity, nor a kind of dopant. Consequently the polyaniline film, which shows very high electrical conductivity, has comparable thermoelectric figure-of-merit (ZT) with feasible inorganic thermoelectric materials such as iron silicide. This revised version was published online in August 2006 with corrections to the Cover Date.     

Synthesis,Electrical Conductivity,Spectral and Thermal Stability Studies on Poly(aniline-co-o-nitroaniline)

o-Nitroaniline units were incorporated in the polyaniline backbone through copolymerization with aniline. The copolymers were synthesized for 1:3 and 1:1 molar ratios of aniline and o-nitroaniline in acidic medium using potassium persulphate as oxidant and their properties were compared with that of polyaniline. The polymers showed less electrical conductivity than polyaniline. Unlike polyaniline, the presence of nitro group caused higher frequency dependence of electrical conductivity. Electronic spectra showed a blue shift in both the band of the copolymers due to the decrease in the extent of conjugation leading to lower conductivity, which could also be explained in terms of a decrease of delocalization of electron as evinced from electron para magnetic resonance (EPR) data. Thermo gravimetric analysis (TGA) revealed that copolymer derived from 1:1 molar ratio showed comparable thermal stability with polyaniline and the one derived from 1:3 molar ratios is thermally less stable than polyaniline. Activation energies for thermal degradation were estimated using Broido equation. The temperature dependence of electrical conductivity suggested charge transport is mainly through variable range hopping.     

掺杂质子酸的类型对聚苯胺结构和电导率的影响

采用化学氧化聚合法以苯胺为单体，过硫酸铵为氧化剂，在不同质子酸的水溶液中合成聚苯胺，考察质子酸对聚苯胺电性能影响，并通过傅立叶红外吸收光谱（FTIR）和紫外可见光吸收光谱（UV－vis)研究聚苯胺掺杂前后结构的变化。结果表明，龙质子酸掺杂后聚 胺具有导电性是因为其分子链上电荷离城形成了共轭结构，具有不同质子酸中生成的聚苯胺氧化程度不同；分子链共轭程度与掺杂酸对阴离子大小有关，掺杂质子酸对阴离子越大，聚苯胺分子链共轭程度越大，电导率也就越高。     

Institut für Physikalische Chemie der Universität Freiburg,Albertstr. 21, D–7800 Freiburg,BRD

The charging/discharging behaviour of polypyrrole, polyaniline as well as of some defined conjugated oligomers with chain-like structure was studied voltammetrically. The results show that the potential dependent charging and discharging processes are mainly caused by faradaic charge transfer reactions. Obviously, there are two classes of conducting polymers, one of which includes, among others, polypyrrole, polythiophene and polyacetylene, whereas polyaniline forms a class of its own.     

聚吡咯/聚苯胺二元复合纳米管及其热电性能

以甲基橙为软模板,六水合三氯化铁为催化剂,在水溶液中通过沉淀聚合法制备了管径为20～180 nm的聚吡咯(PPy)纳米管;以聚吡咯纳米管为基体,通过原位聚合制备了聚吡咯/聚苯胺(PPy/PANi)二元复合纳米管.研究发现,在PPy/PANi二元复合纳米管中,PANi均匀地包覆在PPy纳米管表面,并形成有序堆积,PPy与PANi间存在强烈的π-π共轭作用与氢键作用,当PPy与PANi单体摩尔比为1∶2时,PPy/PANi二元复合纳米管的功率因子在363 K时达到0. 74μW/(m·K²).     

Polyaniline/Silver Nanoparticle-Doped Multiwalled Carbon Nanotube Composites

A simple method was used to synthesize the hybrid nanocomposites consisting of the functionalized multiwalled carbon nanotube composites (MWCNTs) with the polyaniline incorporated silver nanoparticles (a-MWCNT/PANI-Ag) through an emulsion polymerization at room temperature in order to enhance the electrical conductivity of polyaniline. The electrical conductivity of the composite with the incorporated Ag nanoparticles was 5% higher than the same weight percent for the composite without Ag nanoparticles, and the thermal stability was dramatically increased from 54% for the composite (a-MWCNT/PANI) to 69% through the incorporation of the Ag nanoparticles at 830°C. Additionally, the advantages of the Ag nanoparticles, including the improved electrical and thermal properties without damage to the polyaniline structure, were confirmed using FTIR and Raman spectroscopy.     

Composites based on doped polyaniline and polyimide with tricyclodecene structures in the backbone

Conducting composites based on an alicyclic polyimide and polyaniline doped with nonylnaphthalenesulfonic acid or with undoped polyaniline were prepared. Their physicomechanical and electrical properties were studied. The accelerating effect of conducting polymers on the polycondensation was demonstrated.     

Fabrication and evaluation of bacterial cellulose-polyaniline composites by interfacial polymerization

The fabrication and evaluation of nanocomposites based on microbial cellulose and polyaniline (PANi) are described. Microbial cellulose, so called, bacterial cellulose (BC) was introduced to interfacial polymerization of aniline. Two different phases based on water and chloroform made it easy for nanosized PANi particles to be synthesized on BC. Without any help of a surfactant or templates, BC played a critical role of supporting the growth of PANi. As a function of aniline concentration, the corresponding PANi content and volume resistivity were checked. From morphological images observed by FE-SEM, PANi nanoparticles were densely arrayed along every fiber of BC. The conjugated backbone of PANi was thought to contribute to the improvements of thermal stability of PANi/BC composites. The stiffness and brittleness of PANi were compensated by more ductile BC, suggesting BC can be a promising substrate for it. By the simple and facile interfacial polymerization, the electrical conductivity of PANi/BC composites reached up to 3.8?×?10^?1?S/cm when 0.32?M of aniline was used. This PANi/BC nanocomposite can be useful in applications requiring biocompatibility and electrical conductivity such as biological and chemical sensors.     

Current trends in spinel based modified polymer composite materials for electromagnetic shielding

The present article deals with current trends in spinel based modified polymer composite materials for applications in the field of electromagnetic shielding. The interaction between the various spinel based materials and polymers is an emerging field of studies among various researchers. The thermal stability, electrical conductivity, the bonding between the metal ferrites and the polymer plays an important role in the interaction of electromagnetic radiation. These properties also effect the mechanism of the EM waves for the shielding applications. Considering these all properties, polyaniline appears to be an suitable polymer for electromagnetic shielding applications. Polyaniline composites not only reinforced the properties of spinel materials but also enhanced the dielectric properties of the composite material. When carbon based materials such as graphene, graphene oxide and CNT was added along with spinel material in polyaniline based composite, they accelerate the electrical properties and enhances the shielding applications. In this paper the various synthesis methods, fabrication methods of polyaniline, and the properties of polyaniline based composites have been discussed. In addition, the various salient features and futuristic challenges of polyaniline based composite materials for EMI shielding applications were attempted to make a well equipped material for radar absorption.     

Effect of compression pressure on mechanical and electrical properties of polyaniline pellets

While conductivity and other electrical properties are key parameters in the design of polymer electronics, equally important mechanical properties of conducting polymers have rarely been reported. The influence of preparation conditions of polyaniline pellets on mechanical and electrical properties was therefore studied. Conductivity of polyaniline is commonly measured using pellets prepared by the compression of powder. It is shown that a pressure of at least 300 MPa is needed to obtain a reliable value of conductivity. At lower pressures, the samples have lower apparent conductivity, density, Young modulus, and hardness. Above the compression limit of 300 MPa, these parameters become constant, except for the density. The same behavior was observed both for conducting polyaniline hydrochloride and for the non-conducting polyaniline base. The puzzling observation that density of the pellets decreased as the compression pressure increased is discussed considering the relaxation processes.     

Electrochemical synthesis of polyaniline nanocomposite based on modified gold nanoparticles and its application for electrochemical aptasensor

Journal of Solid State Electrochemistry - The method of synthesis of polyaniline, as an important conductive polymer, and the conjugated metal nanomaterials applied in the polymer, determines the...     

水基导电聚苯胺及其复合材料

由于对离子诱导掺杂技术的发展,聚苯胺在有机溶剂中的加工问题已经得到解决,但日益增长的环保要求使得聚苯胺的水系加工倍受关注.本文通过分析聚苯胺水系加工的研究进展,认为从水溶性导电聚苯胺向水分散性导电聚苯胺转变是未来水基导电聚苯胺的主要发展趋势,水基导电聚苯胺复合材料是解决聚苯胺实际应用问题的主要形式.     

Stability of polyaniline in air and acidic water

Polyaniline is a member of the class of electrically conducting polymers, having possible commercial applications such as coatings. Aqueous‐based polyaniline coatings are preferred over organic solvent or concentrated strong acid based coatings because water is not a pollutant. The overall goal of this study was to further the development of water‐based polyaniline coatings by an examination of the effect of acidic water (pH 1.18) and air on polyaniline. Knowledge of the effect of water on the structure, molecular weight, electrical conductivity, and diffusion of the dopant assisted in ascertaining whether polyaniline degraded with water exposure. Knowledge of how Fourier transform infrared (FTIR) spectra would be affected by dry air was important for determining if polyaniline was chemically stable with time. The results showed that the molecular weight, ultraviolet–visible and FTIR spectra, and carbon‐to‐nitrogen molar ratio in the polymer backbone all remained unchanged during acidic water immersion. The constant nature of these physical parameters showed a high degree of water stability. A chloride ion diffusion coefficient of 2.8 to 85 × 10^?9 cm²/h, the chloride concentration, and the electrical conductivity were also measured with the water immersion time. Aging polyaniline powders in a desiccator for 5 years showed no effect on the molecular structure, as indicated by the FTIR spectrum. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 807–822, 2003     

Enhancement of polyaniline’s electrical conductivity by coagulation polymerization

An effective and simple method was developed to prepare highly conductive polyaniline by coagulation polymerization. Depending on the coagulation reaction between aniline salts and lauryl sulfonate (SDS), not only was the polymerization rate of aniline monomers greatly decreased but also the doping efficiency of hydrochloric acid was effectively increased. Low polymerization rate provided enough time for the conformation adjustment of polyaniline chains and the diffusion of doping agent. Meanwhile, the doping efficiency of hydrochloric acid on polyaniline chains was effectively increased due to its easy diffusion among many vacancies, which were generated when SDS separated in the process of polymerization. Therefore, the electrical conductivity of polyaniline prepared by coagulation polymerization was increased more than ten times than that of polyaniline, which was prepared by conventional methods. In addition, the important factors to influence the preparation, such as SDS concentration, hydrochloride acid (HCl) concentration, content of ammonium persulfate (APS), and polymerization time were also investigated. When the molar ratio (aniline:SDS:HCl :APS) was set to 1.69:0.46:15.38:1, the conductivity of polyaniline reached 24.39 S/cm.     

Nanostructured polyaniline sensors

The conjugated polymer polyaniline is a promising material for sensors, since its conductivity is highly sensitive to chemical vapors. Nanofibers of polyaniline are found to have superior performance relative to conventional materials due to their much greater exposed surface area. A template-free chemical synthesis is described that produces uniform polyaniline nanofibers with diameters below 100 nm. The interfacial polymerization can be readily scaled to make gram quantities. Resistive-type sensors made from undoped or doped polyaniline nanofibers outperform conventional polyaniline on exposure to acid or base vapors, respectively. The nanofibers show essentially no thickness dependence to their sensitivity.     

循环伏安法的电扫描方式对苯胺聚合产物形貌影响的观察

在含有0.2 mol.L-1苯胺的0.5 mol.L-1H2SO4溶液中,以扫描速度50 mV.s-1,扫描电位为-0.1~0.9 V,采用循环伏安法(CV),在金属Ti基体上,通过控制扫描方式分别得到了颗粒状、纤维状及管-片状的苯胺聚合产物,分析了形成不同形貌聚苯胺的原因,并通过扫描电子显微镜(SEM)、循环伏安法和电化学阻抗谱(EIS)对不同形貌聚苯胺的结构和性能进行了表征.结果表明,不同形貌聚苯胺的形成是由于聚苯胺的成核及生长模式不同,而无论何种形貌的聚苯胺膜都具有很大的比表面积和良好的导电性能,其中,管-片状聚苯胺的膜层阻抗最小,导电性能最好.     

Electrically insulated molecular wires

This paper is an up-to-date mini-review based on literature data and own results regarding synthesis and properties of conducting (pseudo)rotaxane supramolecular structures. Conjugated polymers, such as polyarylene, polyheteroarylene, polyaniline, polyarylenevinylene or polyaryleneimine, were used as axle, while the macrocyclic components were cyclodextrins, cucurbiturils, cyclophanes or crown ethers. Properties of the supramolecular structure such as solubility, thermal or chemical stability, conductivity, etc. can be drastically modified by the inclusion of hydrophobic conjugated polymers inside the macrocycle, without any chemical modification. For instance, the photophysical properties (i.e. quantum yield of fluorescence and electroluminescence) of the supramolecular structures were enhanced when compared with uninsulated conjugated polymers. The doping process is also affected, because the access of a dopant to the conjugated chain is limited only to the uncovered domains of the conjugated chain.