Use of HPHT Autoclave to Determine Corrosion Inhibition Effect of Poly（methyl methacrylate-co-N-vinyl-2-pyrrolidone） on Carbon Steels in 3.5% NaCl Solution Saturated with CO2

The influence of poly(methylmethacrylate-co-N-vinyl-2-pyrrolidone), P(MMA-co-VP), on corrosion of carbon steels(J55, N80, P110 SS and C110 steels) in 3.5 wt% NaCl solution saturated with CO2 was evaluated using static high pressure and high temperature(HPHT) autoclave. The surface was further evaluated by X-ray diffraction(XRD), scanning electron microscopy(SEM) and contact angle measurements. Quantum chemical calculations have been used to evaluate the structural, electronic and reactivity parameters of the inhibitor on the steels surface. SEM, XRD and contact angle measurement studies reveal that the surface of metals are quite unaffected after use of inhibitor in 3.5% NaCl solution saturated with CO2.     

Thermal,morphological, mechanical and aging properties of polylactide blends with poly(ether urethane) based on chain-extension reaction of poly(ethylene glycol) using diisocyanate

Poly(ether urethane)s(PEU), including PEUI15 and PEUH15, were prepared through chain-extension reaction of poly(ethylene glycol)(PEG-1500) using diisocyanate as a chain extender, including isophorone diisocyanate(IPDI) and hexamethylene diisocyanate(HDI). These PEUs were used to toughen polylactide(PLA) by physical and reactive blending.Thermal, morphological, mechanical and aging properties of the blends were investigated in detail. These PEUs were partially compatible with PLA. The elongation at break of the reactive blends in the presence of triphenyl phosphate(TPP)for PLA with PEUH15 or PEUI15 was much higher than that of the physical blends. The aging test was carried out at-20 °C for 50 h in order to accelerate the crystallization of PEUs. The PEUs in the PLA/PEU blends produced crystallization and formed new phase separation with PLA, resulting in the declined toughness of blends. Fortunately, under the aging condition,although PEUH15 in blends could also form crystallization, the reactive blend of PLA/PEUH15/TPP(80/20/2) had higher toughness than the other blends. The elongation at break of PLA/PEUH15/TPP(80/20/2) dropped to 287% for the aging blend from 350% for the original blend. The tensile strength and modulus of PLA/PEUH15/TPP blend did not change obviously because of the crystallization of PEUH15.     

Mechanical,aging, optical and rheological properties of toughening polylactide by melt blending with poly(ethylene glycol) based copolymers

Two novel biodegradable copolymers, including poly(ethylene glycol)-succinate copolymer (PES) and poly(ethylene glycol)-succinate-l-lactide copolymer (PESL), have been successfully synthesized via melt polycondensation using SnCl₂ as a catalyst. The copolymers were used to toughen PLA by melt blending. The DSC and SEM results indicated that the two copolymers were compatible well with PLA, and the compatibility of PESL was superior to that of PES. The results of tensile testing showed that the extensibility of PLA was largely improved by blending with PES or PESL. At same blending ratios, the elongation at break of PLA/PESL blends was far higher than that of PLA/PES ones. The elongation maintained stable through aging for 3 months. The moisture absorption of the blends enhanced due to the strong moisture absorption of PEG segments in PES or PESL molecules, which did not directly lead to enhance the hydrolytic degradation rate of the PLA. The PLA blends containing 20–30 wt% PES or PESL were high transparent materials with high light scattering. The toughening PLA materials could potentially be used as a soft biodegradable packaging material or a special optical material.     

Shape memory poly(ester urethane) with improved hydrolytic stability

In two hydrolytic degradation studies the tensile (mechanical) and functional (thermo-mechanical) properties of a hydrolysis-stabilized shape memory poly(ester urethane) and its non-stabilized analog were investigated. Hydrolytic degradation was enforced by specimen immersion in de-ionized water at 80 °C. Significant differences in the fundamental shape memory parameters were monitored as function of aging time for the stabilized and non-stabilized polymer. This included the ability to recover strain (shape recoverability) and stress (stress recoverability) on heating after shape programming. Hydrolysis-related mechanical and functional changes were correlated with morphological ones, detected by differential scanning calorimetry (DSC). The shape memory poly(ester urethane), which was protected by a carbodiimide-based hydrolysis stabilizer, revealed significantly improved resistance towards hydrolysis with respect to various mechanical and shape memory parameters.     

Hydrolytic degradation and functional stability of a segmented shape memory poly(ester urethane)

In order to understand the effects of water and hydrolytic ageing on semi-crystalline poly(ester urethane) and its shape memory functionality, water immersion experiments at elevated temperature have been performed on a model substance and various parameters were monitored: change of the melting/crystallisation temperatures, substantial increase in crystallinity, temperature dependence of the water diffusion coefficient and solubility, hydrogen-bonding index and phase mixing by peak deconvolution of the FT-IR carbonyl region and day-to-day tensile and thermo-mechanical cyclic tensile tests. A rising fraction of freezable water agglomerates in the polymer was found for specimens cooled from the immersion temperature. The degradation process could be divided into three phases: an induction phase, a phase of continuous degradation and a phase of accelerated degradation. Shape recovery remains fairly constant during phase one and decreases slowly during phase two. The increase in crystallinity in phase two is accompanied by an increase in shape fixing ability.     

Toughening of polylactide by melt blending with a biodegradable poly(ether)urethane elastomer

Melt blending of polylactide (PLA) and a biodegradable poly(ether)urethane (PU) elastomer has been performed in an effort to toughen the polylactide without compromising its biodegradability and biocompatibility. The miscibility, phase morphology, mechanical properties, and toughening mechanism of the blend were investigated. The blend was found by dynamic mechanical analysis to be a partially miscible system with shifted glass transition temperatures. The PU elastomer was dispersed in the PLA matrix with a domain size of sub-micrometer scale. The addition of PU elastomer not only accelerated the crystallization speed, but also decreased the crystallinity of the PLA. With an increase in PU content, the blend shows decreased tensile strength and modulus; however, the elongation at break and the impact strength were significantly increased, indicating the toughening effects of the PU elastomer on the PLA. The brittle fracture of neat PLA was gradually transformed into ductile fracture by the addition of PU elastomer. It was found that the PLA matrix demonstrates large area, plastic deformation (shear yielding) in the blend upon being subjected the tensile and impact tests, which is an important energy-dissipation process and leads to a toughened, biodegradable polymer blend.     

A Non-isocyanate Route to Poly(ester urethane) with High Molecular Weight: Synthesis and Effect of Chemical Structures of Polyester-diol

A series of non-isocyanate linear high molecular weight poly(ester urethane)s(PETUs)were prepared through an environmentallyfriendly route based on dimethyl carbonate,1,6-hexanediol and 1,6-hexanediamine.In this route,the polyurethane diol was first prepared by the reaction between bis-1,6-hexamethylencarbamate(BHC)and 1,6-hexanediol.A series of polyester soft segments of polyurethane have been synthesized from the polycondensation of adipic acid and different diols,including butanediol,hexanediol,octanediol and decanediol.The subsequent polycondensation of polyurethane diol and polyester diol led to linear PETUs.The resultant polymers were characterized by GPC,FTIR,¹H-NMR,¹³C-NMR,DSC,WAXD,TGA and tensile test.The results indicated that PETUs possess weight-average molecular weights higher than 1×10⁵ and the tensile strength as high as 10 MPa.The thermal properties,crystallization behavior,microphase separation behavior and morphology were studied by DSC and AFM,and the results indicated that the degree of phase separation was affected by two factors,the crystallization and hydrogen bonding interaction between soft segment and hard segment.     

Proton exchange membrane prepared by blending polybenzimidazole with poly (aminophosphonate ester)

In this article, we report a new amorphous-crystalline polymer blend system consisting of poly (4, 4′-diphenylether-5, 5′-bibenzimidazole) (OPBI) and poly (aminophosphonate ester) (PAPE) polymers, the membranes of which were fabricated using the solution blending route. A series of blend membranes at different ratios were prepared and systematically analysed for chemical interactions, morphological changes and their physico-chemical properties studied for use as proton exchange membrane. While FT-IR spectroscopy established the hydrogen bonding interactions between N–H of OPBI and phosphonate ester group of PAPE, X-ray diffraction studies revealed the development of crystallinity in the membrane matrix. Interestingly, the gradual induction of crystallinity in an amorphous OPBI matrix was found to influence the properties of the blend membranes favourably. For instance, the blend membrane containing 25 wt% PAPE in OPBI matrix displayed the maximum property enhancement in terms of storage modulus, glass transition temperature (T_g), phosphoric acid (PA) doping level (37 mol/OPBI repeat unit) and most importantly proton conductivity (0.135 S/cm at 180 °C) which is almost twice the value for pristine OPBI (0.05 S/cm at 180 °C) under identical conditions. Although improved properties were observed at other blend ratios as well, the studies ascertain that the membrane with 25 wt% PAPE was found to be the threshold ratio up to which properties increase and beyond which i.e. at >25 wt% PAPE, there is a decrement in properties like mechanical stability and proton conductivity. An important reason for this was attributed to the creation of a right balance of amorphous and crystalline domains and appropriate intra and inter-polymer hydrogen bonding interactions in the matrix of 75/25 (OPBI/PAPE) blend membrane.     

Synthesis and characterization of crystallizable aliphatic thermoplastic poly(ester urethane) elastomers through a non-isocyanate route

A simple non-isocyanate route is developed for synthesizing crystallizable aliphatic thermoplastic poly(ester urethane) elastomers(TPEURs) with good thermal and mechanical properties. Three prepolymers of1,6-bis(hydroxyethyloxycarbonylamino) hexane(BHCH), i.e. Pre PBHCHs, were prepared through the self-transurethane polycondensation of BHCH. A poly(butylene adipate) prepolymer(Pre PBA) with terminal HO― groups was prepared and used as a polyester glycol. A series of TPEURs were prepared by the co-polycondensation of the Pre PBHCHs with Pre PBA at 170 ℃ under a reduced pressure of 399 Pa. The TPEURs were characterized by gel permeation chromatography, FTIR,1H-NMR, differential scanning calorimetry, thermogravimetric analysis, wide-angle X-ray diffraction, atomic force microscopy, and tensile test. The TPEURs exhibited M_n up to 23300 g/mol, M_w up to 51100 g/mol, Tg ranging from-33.8 ℃ to-3.1 ℃, T_m from 94.3 ℃ to 111.9 ℃, initial decomposition temperature over 274.7 ℃, tensile strength up to18.8 MPa with a strain at break of 450.0%, and resilience up to 77.5%. TPU elastomers with good crystallization and mechanical properties were obtained through a non-isocyanate route.     

Hydrolytic aging of crystallizable shape memory poly(ester urethane): Effects on the thermo-mechanical properties and visco-elastic modeling

The shape memory functionality of a segmented poly(ester urethane) and its hydrolytically aged specimens has been studied by cyclic thermo-mechanical measurements with an imposed strain of 100%. The shape memory effect was triggered by a melting transition in the soft segment phase. Aging was enforced by immersion in hot de-ionized water. In the course of the immersion the tensile properties (secant moduli, stress and strain at yield and break) were impaired by hydrolysis. Advanced specimen embrittlement finally led to rupture during the first thermo-mechanical cycle. This happened after 68 days of aging at 55 °C and correspondingly after 8 days at 80 °C. The residual strain after the first cycle, which was about 25%, increased significantly with aging time. Therefore, the total strain recoverability became ever smaller: aged specimens needed conditioning by at least two cycles for a full development of shape recoverability. Likewise the recovery force decreased continuously. Despite these degradation effects, it was observed that the shape fixity and the cycle-related shape recovery of appropriately conditioned specimens (number of cycles N > 2) remained on a constant high level (at round 100% and between 90% and 100%, respectively) throughout the whole aging period. These observations are discussed within the framework of a simplified model of the behavior of crystallizable shape memory polymers. The amorphous state of the polymer is described by the equation of the linear visco-elastic solid. As for the semi-crystalline state the material is assumed to react elastically with respect to deviations from the configuration, which was frozen up under constraint conditions. The curves of the dependence of the material behavior on aging time at 55 °C match perfectly those at 80 °C when the time axis is adjusted by a factor of 8.5, from which the apparent activation energy for hydrolytic aging in the amorphous state of 82 kJ mol⁻¹ could be deduced.     

Rubber toughening of poly(ether imide) by modification with poly(butylene terephthalate)

Rubber toughening of poly(ether imide) (PEI) has been elusive up to now due to the high processing temperature of PEI, which leads to degradation of the rubber. In this study, by profiting from the miscibility between PEI and poly(butylene terephthalate) (PBT), and the low T_g of PBT, we prepared a blend by melt extrusion with 20 wt% PBT in an attempt to render it toughenable by decreasing its T_g and processing temperature. The PEI-rich blend was subsequently mixed with maleic anhydride (0.9 wt%) grafted poly(ethylene-octene) copolymer (mPEO) up to 30 wt%. The decrease in T_g and processing temperature resulted in no observable degradation of the mPEO, and to the formation of a homogeneous morphology of rubber particles with a fine particle size, indicating that compatibilization was achieved. Upon rubber addition, stiffness decreased, while a very large toughness increase occurred with only 15% mPEO (impact strength more than 10-fold that of the PEI-PBT matrix). Upon observation of the fracture surface, the increase in impact strength was attributed partially to the cavitation and debonding of the rubber particles, and mostly to the deformation and yielding of the PEI-PBT matrix.