Swelling measurement of some ethylene copolymers crosslinked by dicumyl peroxide

Swelling equilibrium of crosslinked ethylene copolymers prepared by the curing of ethylene–vinyl acetate (EVA), ethylene–ethyl acrylate (EEA), and ethylene–acrylic acid (EAA) with dicumyl peroxide (DCP), has been measured in toluene at 23°C. The stress–strain behavior of the swollen EVA and EEA networks was in accord with that predicted from the statistical rubber elasticity theory, while that of the swollen EAA network was divergent. The concentration dependence of the polymer–solvent interaction parameter for the EAA network–toluene system was observed to be highest, while that for the EVA network–toluene system remained nearly zero. The order of the reactivity of pendant groups in the copolymers by radicals from DCP was estimated to be carboxyl > acetyloxy > ethoxycarbonyl group.     

Crystallization of branched polymers. I. Ethylene–vinyl acetate and ethylene–acrylic acid copolymers

The following quantities were measured on a number of ethylene–vinyl acetate (EVA) and ethylene–acrylic acid (EAA) copolymers: (1) the small-angle x-ray scattering invariant, (2) the overall density, and (3) the crystallinity. Assuming a two-phase structure, the separate values of the densities of the crystalline and amorphous regions can be calculated from these data. Of these, the crystalline density is compared with the value obtained from the lattice constants. A systematic difference is observed which is ascribed to the presence of comonomeric side groups in the crystalline regions. For the EVA and EAA samples, their concentration is at least 0.3 and 0.5 times the overall concentration, respectively. The amorphous densities are found to be higher than the values calculated from completely amorphous copolymers by extrapolation procedures.     

小分子药物在半结晶乙烯-醋酸乙烯酯共聚物(EVA)中的扩散机理:自由体积理论

半结晶乙烯 醋酸乙烯酯共聚物 (ＥＶＡ)是扩散控制药物释放体系中使用最多的聚合物 ,它具有生物相容性好 ,加工成型方便 ,机械性能好及理化性质稳定等特点 ,是经ＦＤＡ批准的可用于人体的高分子材料之一 ,已广泛应用于宫内给药体系 ,眼用给药体系 ,透皮给药体系及植入给药体系等 ,并且已有商品化的以ＥＶＡ为基质的药物控制释放系统[1～ 3 ] ,然而对于小分子药物在半结晶ＥＶＡ共聚物中的扩散机理却少见报道 .本文将自由体积理论应用于ＥＶＡ基质型药物扩散控制释药体系 ,阐明了小分子药物在半结晶ＥＶＡ聚合物中的扩散系数随共聚物组成的…     

EAA增容LLDPE/PEO共混物及其增容机理

以乙烯-丙烯酸共聚物(EAA)为增容剂, 研究了它在线性低密度聚乙烯(LLDPE)/聚环氧乙烷(PEO)共混物中的增容作用及其增容机理。采用电子显微镜(SEM)、动态力学分析(DMA)、DSC和红外光谱(IR)对共混物形态及其微观结构进行了表征。结果表明, EAA对LLDPE/PEO共混物有一定的增容作用; 其增容机理为: EAA和LLDPE两者的非晶区部分相容, 而EAA分子中的羧基与PEO分子中的醚氧基相互作用形成了分子间氢键。     

Morphology and thermal properties of a PC/PE blend with reactive compatibilization

Reactive compatibilization of immiscible polymers is becoming increasingly important and hence a representative study of a polycarbonate/high density polyethylene (PC/HDPE) system is the focus of this paper. A grafted copolymer PC‐graft‐ethylene‐co‐acrylic acid (PC‐graft‐EAA) was generated as a compatibilizer in situ during processing operation by ester and acid reaction between PC and ethylene‐acrylic acid (EAA) in the presence of the catalyst dibutyl tin oxide (DBTO). As the polyethylene (PE) matrix does not play any part during the synthesis of the copolymer and since PC and EAA are also immiscible, to simplify the system, the influence of this copolymer formation at the interface between PC and EAA on rheological properties, phase morphology, and crystallization behavior for EAA/PC binary blends was first studied. The equilibrium torque increased with the DBTO content increasing in EAA/PC blends on Haake torque rheometer, indicating the in situ formation of the graft copolymer. Scanning electron microscopy (SEM) studies of cryogenically fractured surfaces showed a significant change at the distribution and dispersion of the dispersed phase in the presence of DBTO, compared with the EAA/PC blend without the catalyst. Differential scanning calorimetry (DSC) studies suggested that the heat of fusion of the EAA phase in PC/EAA blends with or without DBTO reduced with the formation of the copolymer compared with pure EAA. Then morphological studies and crystallization behavior of the uncompatibilized and compatibilized blends of PC/PE were studied as functions of EAA phase concentration and DBTO content. Morphological observations in PC/PE blends also revealed that on increasing the EAA content or adding the catalyst DBTO, the number of microvoids was reduced and the interface was intensive as compared to the uncompatibilized PC/PE blends. Crystallization studies indicated that PE crystallized at its bulk crystallization temperature. The degree of crystallinity of PE phase in PC/PE/EAA blends was also reduced with the addition of EAA and DBTO compared to the uncompatibilized blends of PC/PE, indicating the decrease in the degree of crystallinity was more in the presence of PC‐graft‐EAA. Copyright © 2007 John Wiley & Sons, Ltd.     

利用~1H-NMR研究HDPE/PET/EVA共混体系的酯交换反应

本文在选用EVA作为HDPE/PET共混体系增容剂的基础上 ,通过双螺杆反应挤出熔融加工过程 ,促使EVA侧基上的酯基官能团与PET组分主链上的酯基在适当催化剂———有机金属化合物存在的条件下发生酯交换反应 .1H NMR结果表明 ,酯交换反应的产生在共混体系界面原位形成接枝或交联的PET EVA共聚物 ,且主要是以生成接枝共聚物的反应为主 .     

Adhesive properties of ethylene and vinyl acetate copolymer. Deformation strength characteristics: Contribution of plastic deformation work

The deformation-stress curves of ethylene and vinyl acetate copolymer (EVA) are determined by traditional methods with respect to composition at various rates of deformation. The residual deformations after relief are estimated. The deformation work is calculated and the effect of copolymer composition on the value of plastic deformation is evaluated. According to the previously suggested model, the contribution of deformation characteristics of EVA adhesive to the adhesive joint fracture energy is estimated.     

Improved Adhesion of UV Treated EVA Copolymer by Adding Small Amounts of Fillers

The influence of adding small amounts of calcium carbonate or sepiolite fillers on the adhesion properties of UV surface-treated ethylene vinyl acetate copolymer (EVA) was studied. In this paper, it has been demonstrated that the addition of 3-7 wt% filler enhanced the extent of the surface modifications (wettability, surface chemistry, roughness) and increased the adhesion of EVA. These effects were more marked when 7 wt% sepiolite filler was added to EVA, likely due to its higher aspect ratio.     

Kinetic Study of the Accelerating Effect of Coal-burning Additives on the Combustion of Graphite

The relationship between copolymer composition and transition temperatures was studied by means of differential scanning calorimetric analysis and dynamic mechanical spectroscopy. Six samples of ethylene vinyl acetate (EVA) copolymers containing from 5 to 40 mass per cent of vinyl acetate (VA) were studied. The differential scanning calorimetric analysis revealed that each EVA copolymer displays two endothermic peaks (T_m1 and T_m2 ) in the melting zone. Dynamic mechanical spectroscopy was used to determine the primary relaxation temperature (T_α ) for EVA copolymers. This latter characteristic is relatively insensitive to the level of vinyl acetate contained in the copolymer and is influenced by the pulsation frequency ω, also named the angular frequency. This revised version was published online in July 2006 with corrections to the Cover Date.     

Enhancement of thermal,mechanical and barrier properties of EVA solar cell encapsulating films by reinforcing with esterified cellulose nanofibres

Solar cell encapsulating film based on ethylene vinyl acetate copolymer (EVA) was modified by using bacterial cellulose (BC) nanofibres. Bacterial cellulose was chemically modified with propionic anhydride prior to compounding with EVA in a twin screw extruder. The effects of fibre content on the mechanical, thermal, optical and barrier properties of the EVA composite films were investigated. Better mechanical and barrier properties of the EVA films were obtained when the modified BC nanofibres were used. The results were ascribed to the different chemical functional groups on the fibre surface, as verified by FTIR spectra. Deacetylation of the EVA was delayed and visible light transparency of the EVA films above 75% was retained. Overall, our study showed that it was possible to improve the barrier properties of EVA film without sacrificing much transparency by using a suitable type and content of cellulose nanofibres.     

The rheological behavior of ethylene vinyl acetate copolymer/rectorite nanocomposites during the melt extrusion process

To optimize the preparation process for ethylene vinyl acetate (EVA)/rectorite nanocomposites during the melt extrusion, the effect of rectorite on the rheological property of molten polymer has been explored in this paper. The dispersion of rectorite in EVA was probed by X‐ray diffraction, and the rheological behaviors of EVA copolymer and EVA/rectorite nanocomposites during the extrusion process were investigated by means of HAAKE minilab. The positron results reveal that introducing the rectorite in EVA matrix increases the interfaces in composites. And the rheological results indicate that the viscosity of EVA and EVA/rectorite nanocomposites in the molten state was influenced by the processing temperature, processing time and shearing rate. For all the samples, the viscosity increases with increasing the shear rate, and decreases with increasing extrusion temperature. Moreover, compared with the pure EVA, the EVA/rectorite nanocomposite presents a lower viscosity at the same processing condition. Copyright © 2016 John Wiley & Sons, Ltd.     

The application of the synergistic effect between the crystal structure of poly(lactic acid) (PLA) and the presence of ethylene vinyl acetate copolymer (EVA) to produce highly ductile PLA/EVA blends

Journal of Thermal Analysis and Calorimetry - In this paper, we produced ethylene vinyl acetate copolymer (EVA)-filled poly(lactic acid) (PLA) blends by extrusion and injection moulding. We...     

Preparation of Exfoliated Low-density Polyethylene/Montmorillonite Nanocomposites Through Melt Extrusion

Introduction Polymer layeredsilicatenanocompositesexhibit somesuperiorcharacteristics,suchasthermal,me chanicalandbarrierproperties,incomparisonwiththe polymermatrixes[1—3].Intercalationpolymerization[4],polymersolutionintercalation[5]andpolymermeltinter…     

Irradiation effects on thermal,surface, and physicomechanical properties of ethylene and vinyl acetate copolymer

The structural and thermal transitions for ethylene and vinyl acetate copolymer (EVA) samples irradiated by fast electrons at doses in the range of 2.5–25 Mrad were investigated by DSC and X-ray diffraction analysis. The parameters of chemical bonds in the amorphous phase of copolymer were determined. The change in the degree of crystallinity, melting temperature, and crystallite sizes before and after radiochemical modification were estimated. The obtained results were analyzed and corresponded to the physicomechanical properties of copolymers. The surface energy of copolymers before and after irradiation was defined. The strength of adhesive joints based on EVA from PET substrates and the influence of radiochemical modification of adhesive before joint formation on its strength were analyzed.     

Evidence of electron acceptor - electron donor interactions in thermoplastic polymer blends by using FTIR - ATR spectroscopy

Specific interactions in binary blends of ethylene/vinyl acetate copolymer (EVA) with various low molecular weight terpene-phenol tackifying resins (TPR) were systematically investigated, as a function of the composition of the blend and of the electron-acceptor ability of the resin, by using attenuated total reflection-Fourier transform infrared (ATR-FTIR) spectroscopy. Molecular acid-base were evidenced between TPR hydroxyl groups and EVA carbonyl groups. Quantitative information on the fraction of acid-base bonded entities, the enthalpy and the equilibrium constant of pair formation were obtained. A crystalline transition of the EVA copolymer is observed and is discussed in terms of enthalpy and entropy considerations based on FTIR and calorimetric differential scanning calorimetry (DSC) investigations. Fundamental results are then summarized in order to predict the interfacial reactivity of such polymer blends towards acid or basic substrates.     

EFFECT OF VINYL ACETATE CONTENT ON THE MECHANICAL PROPERTIES AND MORPHOLOGICAL STRUCTURES OF POLYPROPYLENE

The effect of vinyl acetate （VA） content in ethylene vinyl acetate （EVA） copolyrner on the mechanical properties of polypropylene was investigated. Three different EVA copolymers with concentrations of 3 wt%, 6 wt%, 9 wt%, 12 wt% and 15 wt%, were blended to polypropylene. The mechanical properties such as yield and tensile strengths, elastic modulus, Izod impact strength, hardness and melt flow index of the blends were investigated. Relationship between type of vinyl acetate and concentrations, mechanical, MFI and morphological properties were explored.     

聚乳酸/乙烯-醋酸乙烯酯共聚物共混物的形态与黏弹行为

熔融共混制备了不同组分比的聚乳酸(PLA)/乙烯-醋酸乙烯酯共聚物(EVA)共混物,采用扫描电子显微镜(SEM)、溶剂选择性蚀刻和旋转流变仪研究了共混物不相容的相形态及其黏弹响应.研究结果表明,PLA/EVA共混物为典型的热力学不相容体系,两基体组分间的界面张力约为2.2 mN/m;因此随组分比的不同,共混物表现出"海-岛"分散和双连续的不相容相形态;体系中EVA的相反转浓度约为50 wt%～60 wt%,这与黏性模型对相反点预测的结果一致;与双连续相形态的体系相比,乳液模型能够更好的描述具有"海-岛"分散形态的体系的线性黏弹响应,共混体系相对较宽的相反转区域主要源于两组分间较大的弹性比以及EVA自身的屈服行为.     

Conducting composites from EPDM–EVA blends

The effect of ethylidene norbornene (ENB) content of ethylene propylene aiene rubber (EPDM) and vinyl acetate (VA) content of ethylene vinyl acetate copolymer (EVA), as well as the blending sequence, on the conductivity of composites based on EPDM–EVA–carbon black have been studied. Black master batches show a lower extent of cure than the preblended system followed by black addition. EPDM having a high ENB content shows higher conductivity under ambient conditions. Preblended systems give rise to higher conductivity in the case of low-ENB content EPDM. But for high-ENB content EPDM, the blending of black master batches imparts high conductivity. Two types of conduction are observed in this case and the transition temperature depends on the VA content of EVA. It appears that there exists a correlation between activation energy of curing and that of conduction.     

Miscibility behavior of ethylene/vinyl acetate and C5 petroleum resin by FTIR imaging.

FTIR microscopic imaging was used to investigate the miscibility behavior of ethylene/vinyl acetate copolymer (EVA) and C5 petroleum resin. Images with an area of 500 x 500 microm(2) were collected in the reflection mode. The miscibility was characterized by probing the spatial distribution of the carbonyl group (C=O) of EVA in the whole images. It was found that a 1:1 hot-melt mixture of EVA and C5 resin showed a good miscibility behavior. For two different EVA copolymers, one with 18% vinyl acetate (VAc) content showed a better miscibility behavior than that with 28% VAc content. Our results demonstrated that this method allowed a direct, convenient and nondestructive visualization. This developed technique promises to become a powerful tool for studying the miscibility behavior of composite materials.     

ASSOCIATION OF ETHYLENE—VINYL ACETATE COPOLYMER IN DILUTE SOLUTIONS Ⅲ. CRITICAL ASSOCIATION CONCENTRATION*

Association behavior of ethylene vinyl acetate (EVA) copolymer in foursolvents 1, 2-dichloroethane (DCE), cyclohexane (CYH), xylene (XYL) and chloroform(CF) has been investigated by dilute solution viscometry The critical association concen-tration (C_A) was determined at which the incipient decrease in slope of the η_(sp)/C～ Ccurve in solutions at the dilute regime. Our results showed that whether the CA couldexist depends on solvent property. The values of CA in DCE increase with increasing, oftemperature and vinyl acetate (VA) content in EVA and decreasing of molecular weight ofEVA.