Synthesis and Properties of New Fluorinated Polyimides Derived from an Unsymmetrical and Noncoplanar Diamine

A new unsymmetrical and noncoplanar diamine containing trifluoromethyl and trimethyl groups, 1,4‐bis(4‐amino‐2‐trifluoromethylphenoxy)‐2,3,5‐trimethylbenzene ( 2 ), was synthesized using 2,3,5‐trimethylhydroquinone and 2‐chloro‐5‐nitrobenzotrifluoride as starting materials. A series of fluorinated poly(ether imide)s (PEIs) ( 4a–4d ) were prepared from diamine 2 with four aromatic dianhydrides via a one‐step high‐temperature polycondensation procedure. The obtained PEIs were readily soluble in most organic solvents and could be solution‐cast into flexible and strong films. The resulting thin films exhibited light color and good optical transparency with a cutoff wavelength of 356–376 nm. They also displayed good thermal stability with glass transition temperatures (T_g) above 281°C, 10% weight loss temperatures in the range of 482–486°C, and the weight residue more than 55% at 800°C in nitrogen. Moreover, they revealed low dielectric constants (2.77–2.93 at 1 MHz) and low moisture absorptions (0.41%–0.57%).     

Poly(1,3,4-oxadiazole-amide)s containing pendent imide groups

A series of new poly(1,3,4-oxadiazole-amide)s containing pendent imide groups has been synthesized by solution polycondensation of aromatic diamines containing preformed 1,3,4-oxadiazole rings with two diacid chlorides containing imide rings. These polymers were also prepared by the reaction of the same diacid chlorides with p-aminobenzhydrazide which were subsequently cyclodehydrated in solid state. The polymers were soluble in polar amidic solvents and some of them gave transparent flexible films by casting from solutions. They showed high thermal stability with decomposition temperatures above 400°C and glass transition temperatures in the range of 245–327°C. They had low dielectric constants, in the range of 3.32–3.94, and good tensile properties.     

Fluorene‐rich high performance polyesters: Synthesis and characterization of 9,9‐fluorenylidene and 2,7‐fluorenylene‐based polyesters with excellent optical property

Polyesters PEs containing high content of fluorene units in their backbones were synthesized from 9,9‐diarene‐substituted fluorene diols ( 1 ) and fluorene‐based diacid chlorides ( 2 ) by high temperature polycondensation at 185 °C in diphenyl ether. The molecular weights of the polyesters PE1‐PE5 were in a range of M_w 25,000–165,000. The polyesters displayed their high thermostability: the glass transition temperatures (T_g) by differential scanning calorimetry analysis ranged from 109 to 217 °C, while the 10% weight loss temperatures (T_d10) measured by thermogravimetric analysis were over 400 °C in nitrogen and 395 °C in air. The polyesters had good solubility in most common organic solvents such as chloroform and toluene and gave tough, transparent and flexible cast films. The transmittance of the films was over 80% in the wavelength range from 450 to 700 nm in any PEs . The PEs exhibited high refractive index values around 1.65, while they had very low degree of birefringence. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 2549–2556, 2008     

Fluorinated polyimide/POSS hybrid polymers with high solubility and low dielectric constant

A series of fluorinated polyimide/POSS hybrid polymers(FPI-4-FPI-16) were prepared via a facile synthetic route using 2,2'-bis(trifluoromethyl)benzidine, 4,4'-oxydiphthalic dianhydride and monofunctional POSS as starting materials. The hybrid polymers showed excellent solubility and film formation ability. Flexible and robust hybrid films could be conveniently obtained via solution-casting. The hybrid films demonstrated low dielectric constants and high thermal stability. Their dielectric constants were in the range of 2.47–2.92 at 1 MHz measured for their capacitance, and were tunable and decreased with an increase of POSS content. Their 10% weight loss temperatures were in the range of 539-591 ℃ and the weight residual at 800 ℃ ranged from 48% to 53% in nitrogen atmosphere. These hybrid films also possessed good mechanical properties and hydrophobic characteristics. This work could provide a potential strategy for the preparation of fluorinated polyimide/POSS hybrid polymers.     

Synthesis and characterization of novel aromatic polyamides containing 3-trifluoromethyl-substituted triphenylamine

A new 3-trifluoromethyl-substituted triphenylamine-containing aromatic diacid monomer, N,N-bis(4-carboxyphenyl)-3-trifluoromethylaniline, was prepared by the substitution reaction of 3-trifluoromethylaniline with 4-fluorobenzonitrile, followed by alkaline hydrolysis of the dinitrile intermediate. Novel aromatic polyamides with 3-trifluoromethyl-substituted triphenylamine moieties were prepared from the diacid and various aromatic diamines via the direct phosphorylation polycondensation. All the polyamides were amorphous and readily soluble in many polar organic solvents such as N,N-dimethylacetamide and N-methyl-2-pyrrolidone, and could be solution-cast into transparent, tough, and flexible films with good mechanical properties. They exhibited good thermal stability with relatively high glass-transition temperatures (258–327°C), 10% weight-loss temperatures above 500°C, and char yields higher than 60% at 800°C in nitrogen. These polymers had low dielectric constants of 3.22–3.70 (100 Hz), low moisture absorption in the range of 1.75–2.58%, and high transparency with an ultraviolet–visible absorption cut-off wavelength in the 375–395 nm range. Cyclic voltammograms of the polyamide films cast onto an indium tin oxide coated glass substrate exhibited a reversible oxidation redox couple with oxidation half-wave potentials (E_1/2) of 0.95–1.00 V vs. Ag/AgCl in an acetonitrile solution.     

Synthesis and characterization of new soluble aromatic polyamides based on 4‐(1‐adamantyl)‐1, 3‐bis(4‐aminophenoxy)benzene

A set of new aromatic polyamides were synthesized by the direct phosphorylation condensation of 4‐(1‐adamantyl)‐1,3‐bis‐(4‐aminophenoxy)benzene with various diacids. The polymers were produced with high yields and moderate to high inherent viscosities (0.43–1.03 dL/g), and the weight‐average molecular weights and number‐average molecular weights, determined by gel permeation chromatography, were in the range of 37,000–93,000 and 12,000–59,000, respectively. The polyamides were essentially amorphous and soluble in a variety of solvents such as N,N‐dimethylacetamide (DMAc), cyclohexanone, and tetrahydrofuran. They showed glass‐transition temperatures in the range of 240–300 °C (differential scanning calorimetry) and 10% weight‐loss temperatures over 450 °C, as revealed by thermogravimetric analysis in nitrogen. All the polymers gave strong films via casting from DMAc solutions, and these films exhibited good mechanical properties, with tensile strengths in the range of 77–92 MPa and tensile moduli between 1.5 and 2.5 GPa. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 1014–1023, 2000     

Synthesis and characterization of new cardo polyimides prepared from 5,5-Bis[4-(4-aminophenoxy)phenyl]-4,7-methanohexahydroindane

A new cardo diamine monomer, 5,5-bis[4-(4-aminophenoxy)phenyl]-4,7-methanohexahydroindane (II), was prepared in two steps with high yield. The monomer was reacted with six different aromatic tetracarboxylic dianhydrides in N,N-dimethylacetamide (DMAc) to obtain the corresponding cardo polyimides via the poly(amic acid) precursors and thermal or chemical imidization. All the poly(amic acid)s could be cast from their DMAc solutions and thermally converted into transparent, flexible, and tough polyimide films which were further characterized by x-ray and mechanical analysis. All of the polymers were amorphous and the polyimide films had a tensile strength range of 89–123 MPa, an elongation at break range of 6–10%, and a tensile modulus range of 1.9–2.5 GPa. Polymers V_c, V_e, and V_f exhibited good solubility in a variety of solvents such as N-methyl-2-pyrrolidinone (NMP), DMAc, N,N-dimethylformamide (DMF), dimethyl sulfoxide (DMSO), pyridine, γ-butyrolactone, and even in tetrahydrofuran and chloroform. These polyimides showed glass-transition temperatures between 274 and 299°C and decomposition temperatures at 10% mass loss temperatures ranging from 490 to 521°C and 499 to 532°C in nitrogen and air atmospheres, respectively. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 2815–2821, 1999     

Synthesis and characterization of aromatic polymers containing pendant silyl groups. I. Polyarylates

Polyarylates containing pendant silyl group were prepared by the phase-transfer catalyzed, two-phase polycondensations of 2,2-bis (4-hydroxyphenyl) propane with corresponding dicarbonyl chlorides such as 2-trimethylsilylterephthaloyl chloride, 5-trimethylsilylisophthaloyl chloride, 5-dimethylphenylsilylisophthaloyl chloride, and 5-triphenylsilylisophthaloyl chloride. The resulting amorphous polyarylates with glass transition temperatures of 163–214°C had inherent viscosities in the range of 0.41–0.95 dL/g. These polyarylates were readily soluble in common chlorinated hydrocarbons and it was possible to obtain transparent, flexible, and tough films from the polymer solutions. The prepared polyarylates showed fairly good thermal stabilities as well as tensile strengths, i.e., the tensile strengths of the cast films from chloroform solution were 6.0–6.7 kg/mm². And TGA data revealed 10% weight losses and residual weights at 800°C were 437–495°C and 27–40% under nitrogen atmosphere, respectively. © 1992 John Wiley & Sons, Inc.     

SYNTHESIS AND CHARACTERISTICS OF NOVEL POLYAMIDES HAVING PENDENT N-PHENYL IMIDE GROUPS

We have investigated a novel monomer having a pendent phenyl imide group for preparing new cycloaliphatic-aromatic polyamides. Novel polyamides were synthesized by a direct polycondensation reaction of N-phenyl-2,3-imide cyclopentane-1,4-dicarboxylic acid (PCPA) and various aromatic diamines. A direct polycondensation was carried out by a Yamazaki's direct polycondensation that is typical of using triphenyl phosphite, lithium chloride, and pyridine. Inherent viscosity of these resulting polyamides was in the range 0.47–1.05 dL/g. The glass transition temperatures of these polyamides were in the range of 190–200°C. The decomposition temperatures of them were in the range of 310–323°C in nitrogen atmosphere. The Solubility of these polyamides are good in aprotic solvents such as DMAc (N,N-Dimethylacetamide), NMP (N-Methyl-2-Pyrrolidinone) and DMF (N,N-Dimethylformamide). Transparent, flexible, and tough films were cast from DMAc solutions.     

Evolution of surface topography and optical band gap of ZnO film deposited on NiO/Si(100)

Evolution of surface features and optical band gap of ZnO thin films deposited on different NiO/Si(100) are reported. In order to create different initial microstructure, we first deposited NiO film on Si(100) at 3 different temperatures (400°C, 650°C, and 700°C) by pulsed laser deposition. These NiO/Si(100) films are used as substrate for the deposition of ZnO films. Combining the results obtained from grazing incidence X‐ray diffraction, atomic force microscope, and UV‐Visible characterization, our study indicated that the microstructure of the substrate takes the important role in dictating properties of the film. Our study also indicated that one needs to choose appropriate synthesis condition to achieve good quality ZnO films.     

Substrate temperature effects on the structural,compositional, and electrical properties of VO2 thin films deposited by pulsed laser deposition

The vanadium dioxide (VO₂) thin films were deposited on silicon (100) substrate using the pulsed laser deposition technique. The thin films were deposited at different substrate temperatures (500°C, 600°C, 700°C, and 800°C) while keeping all the other parameters constant. X‐ray diffraction confirmed the crystalline VO₂ (B) and VO₂ (M) phase formation at different substrate temperatures. X‐ray photoelectron spectroscopy analysis showed the presence of V⁴⁺ and V⁵⁺ charge states in all the deposited thin films which confirms that the deposited films mainly consist of VO₂ and V₂O₅. An increase in the VO₂/V₂O₅ ratio has been observed in the films deposited at higher substrate temperatures (700°C and 800°C). Scanning electron microscope micrographs revealed different surface morphologies of the thin films deposited at different substrate temperatures. The electrical properties showed the sharp semiconductor to metal transition behavior with approximately 2 orders of magnitude for the VO₂ thin film deposited at 800°C. The transition temperature for heating and cooling cycles as low as 46.2°C and 42°C, respectively, has been observed which is related to the smaller difference in the interplanar spacing between the as‐deposited thin film and the standard rutile VO₂ as well as to the lattice strain of approximately −1.2%.     

Synthesis and characterization of siloxane resins derived from silphenylene‐siloxane copolymers bearing benzocyclobutene pendant groups

Two bis(dimethylamimo)silanes with benzocyclobutene (BCB) groups, bis(dimethylamino)methyl(4′‐benzocyclobutenyl)silane ( 2 ) and bis(dimethylamino)methyl [2′‐(4′‐benzocyclobutenyl)vinyl]silane ( 4 ), were synthesized from different synthetic routes, which were then employed to prepare two novel silphenylene‐siloxane copolymers (SiBu and SiViBu) bearing latent reactive BCB groups by polycondensation procedure with 1,4‐bis(hydroxydimethylsilyl)benzene. At elevated temperatures these copolymers were readily converted to highly crosslinked films and molding disks with network structures by polymer chain crosslinking, which followed the first‐order kinetic reaction model. The final resins of SiBu and SiViBu demonstrated excellent thermal stability with high glass transition temperatures (218 and 256 °C) and high temperatures at 5% weight loss (553 and 526 °C in N₂, 530 and 508 °C in air). After aging at 300 °C in air for 100 h, the cured resins showed weight loss lower than 4%. The films of cured SiBu and SiViBu also exhibited relatively low dielectric constants of 2.66 and 2.64, low dissipation factors of 2.23 and 2.12 × 10^?3, low water absorptions (≤0.28%), and high transparence in the visible region with cutoff wavelengths of 321 and 314 nm. Moreover, the aged films exhibited good dielectric properties and low water absorptions. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 7868–7881, 2008     

Effect of thickness and monolayer location on thermostability of metal stearate LB films studied by FT-IR reflection—absorption spectroscopy

LB films of Cd and Ca stearates with 1, 3, 9, and 21 monolayers were fabricated on silver-coated glass slides. 9-Monolayer LB films of Cd and Ca salts of deuterated stearic acid, in which the 1st, 5th, or 9th layer was replaced by 1 monolayer of undeuterated analogues, were also prepared on the above substrates. Temperature dependences of Fourier transform infrared (FT-IR) reflection—absorption (RA) spectra were examined for these LB films in the range 31–140°C. At room temperature, the hydrocarbon chains in these LB films were in a well-ordered state with a high degree of perpendicular orientation to the substrate. However, they became disordered at elevated temperatures. These order-disorder phase transition temperatures were dependent on the film thickness, to a small degree in the Cd stearate LB film (102–108°C), but to a large degree in the Ca stearate LB film (103–129°C). In the latter LB film, the effect of dehydration was inferred. The degree of disorder at high temperatures was dependent on the film thickness and the location of monolayer in the 9-monolayer LB films. This result is discussed in terms of the internal pressure within the LB film.     

Synthesis and properties of polyimides derived from 1,6-bis(4-aminophenoxy)naphthalene and aromatic tetracarboxylic dianhydrides

1,6-Bis(4-aminophenoxy)naphthalene ( I ) was used as a monomer with various aromatic tetracarboxylic dianhydrides to synthesize polyimides via a conventional two-stage procedure that included ring-opening polyaddition in a polar solvent such as N,N-dimethylacetamide (DMAc) to give poly(amic acid)s, followed by thermal cyclodehydration to polyimides. The diamine ( I ) was prepared through the nucleophilic displacement of 1,6-dihydroxynaphthal-ene with p-chloronitrobenzene in the presence of K₂CO₃, followed by catalytic reduction. Depending on the dianhydrides used, the poly(amic acid)s obtained had inherent viscosities of 0.73–2.31 dL/g. All the poly(amic acid)s could be solution cast and thermally converted into transparent, flexible, and tough polyimide films. The polyimide films had a tensile modulus range of 1.53–1.84 GPa, a tensile strength range of 95–126 MPa, and an elongation range at break of 9–16%. The polyimide derived from 4,4′-sulfonyldiphthalic anhydride (SDPA) had a better solubility than the other polyimides. These polyimides had glass transition temperatures between 248–286°C (DSC). Thermogravimetric analyses established that these polymers were fairly stable up to 500°C, and the 10% weight loss temperatures were recorded in the range of 549–595°C in nitrogen and 539–590°C in air atmosphere. © 1995 John Wiley & Sons, Inc.     

Synthesis of two-dimensional gallium nitride via spin coating method: influences of nitridation temperatures

This paper reports the synthesis and characterization of gallium nitride (GaN) thin films deposited on p-type silicon (100) substrates by using low cost spin coating method under various nitridation temperatures. This work demonstrated that spin coating with the new prepared precursor solution can be used as a versatile method for the successfully growth of GaN thin films. Furthermore, the influence of varying nitridation temperatures on the structural, morphological, and optical properties of synthesized GaN thin films were studied in this work. The GaN thin films were characterized by X-ray diffraction, field-emission scanning electron microscopy, atomic force microscopy, photoluminescence and Raman spectroscopy. All the characteristics of the GaN thin films were effectively improved with the increasing of the nitridation temperatures from 750 to 950 °C and degraded at temperature of 1,050 °C. The measured results show that nitridation temperature plays an important role in improving the crystalline quality of the GaN thin films and the most efficient nitridation temperature was at 950 °C.     

Synthesis and properties of polyamides derived from 1, 4-bis(4-aminophenoxy)-2-tert-butylbenzene

1, 4-Bis(4-aminophenoxy)-2-tert-butylbenzene was synthesized and used as a monomer to prepare a series of polyamides by the direct polycondensation with various aromatic dicarboxylic acids in N-methyl-2-pyrrolidone using triphenyl phosphite and pyridine as condensing agents. All the polymers were obtained in quantitative yields with inherent viscosities of 0.75–1.75 dL g⁻¹. All the polyamides showed amorphous nature and most of them were soluble in polar solvents. Polyamides derived from 4, 4'-sulfonyldibenzoic acid and 4, 4'-hexafluoroisopropylidenedibenzoic acid were even soluble in common organic solvent such as THF. All polyamide films could be obtained by casting from their DMAc or NMP solutions. The polyamide films had a tensile strength range of 35–84 MPa, an elongation range at break of 3–7%, and a tensile modulus range of 1.2–2.5 GPa. These polyamides had glass transition temperatures between 203–268°C and 10% mass loss temperatures were recorded in the range of 456–472°C in nitrogen and 453–470°C in air atmosphere.     

Organosoluble,low dielectric constant and highly transparent fluorinated pyridine-containing poly(ether imide)s derived from new diamine: 4-(4-trifluoromethyl)phenyl-2,6-bis[4-(4-amino-2-trifluoromethylphenoxy)phenyl]pyridine

A new aromatic diamine, 4-(4-trifluoromethyl)phenyl-2,6-bis[4-(4-amino-2-trifluoromethylphenoxy)phenyl]pyridine, was synthesized by a modified Chichibabin reaction of 4-(4-nitro-2-trifluoromethylphenoxy)acetophenone with 4-triflouromethylbenzaldehyde, followed by catalytic reduction. A series of fluorinated pyridine-containing aromatic poly(ether imide)s (PEIs) were prepared from the diamine monomer with various aromatic dianhydrides via conventional two-step thermal imidization method. The resulting PEIs had inherent viscosities values of 0.68–0.90 dL/g, and could be cast and thermally converted into transparent, flexible, and tough polymer films. These PEIs were predominantly amorphous, had good solubility in common solvents such as NMP, DMAc and m-cresol at room temperature, and displayed excellent thermal stability with the glass transition temperatures of 258–315?°C, the temperatures at 5% weight loss of 550–585?°C, and the residue of higher than 55% at 750?°C in nitrogen. Moreover, the PEIs films showed outstanding mechanical properties with tensile strengths of 74.8–103.5?MPa, tensile moduli of 1.08–1.45?GPa, and elongations at break of 10.6–24.4%. These PEIs also exhibited low dielectric constants of 2.81–2.98 (1?MHz) and water uptake 0.39–0.68%, as well as high optical transparency with the UV cutoff wavelength in the 350–378?nm range and the wavelength of 80% transparency in the range of 412–510?nm.     

Hafnia sol-gel films synthesized from HfCl4: Changes of structure and properties with the firing temperature

Thin sol-gel hafnia films have been synthesised from HfCl₄, the synthesis has revealed to be a simple route to fabrication of hafnia films with high transparency in the UV-visible range. The films have been fired at different temperatures in air up to 1000°C and have been characterized by X-ray diffraction and Fourier transform infrared spectroscopy. Infrared absorption spectra of hafnia films have allowed to follow the formation of monoclinic crystalline phases together with XRD. Formation of monoclinic hafnia crystallites has been observed upon calcination at temperatures higher than 600°C, as shown by infrared spectroscopy and XRD. The optical transmission and the refractive index as a function of the temperature of firing have been characterized by UV-Visible spectroscopy and spectroscopic ellipsometry. The hafnia films, after firing at 600°C, had a refractive index of 1.92 with a thickness of around 70 nm.     

Synthesis and characterization of highly refractive polyimides from 4,4′‐thiobis[(p‐phenylenesulfanyl)aniline] and various aromatic tetracarboxylic dianhydrides

An aromatic sulfur‐containing diamine 4,4′‐thiobis[(p‐phenylenesulfanyl) aniline] (3SDA) was synthesized and polymerized with a sulfur‐containing dianhydride 4,4′‐[p‐thiobis(phenylenesulfanyl)]diphthalic anhydride (3SDEA) and three nonsulfur aromatic tetracarboxylic dianhydrides, respectively to afford four poly(amic acid)s (PAAs) with the inherent viscosities of 0.54–1.04 dL/g. Flexible and tough polyimide (PI) films obtained from the PAA precursors showed good thermal, mechanical, and optical properties. The glass transition temperatures (T_gs) of the PIs ranged from 179.1–227.2 °C determined by differential scanning calorimetry (DSC), and 173.8–227.3 °C by dynamic mechanical analysis (DMA), depending on the dianhydride used. The 10% weight loss temperatures were in the range of 500–536 °C, showing high intrinsic thermal‐resistant characteristics of the PI films. The PI films also showed good optical transparency above 500 nm, which agreed well with the calculated absorption spectra using the time‐dependent density functional theory. The average refractive indices (n_av) measured at 632.8 nm were 1.7191–1.7482, and the in‐plane/out‐of‐plane birefringences (Δn) were 0.0068–0.0123. The high refractive indices originate from the high sulfur contents, good molecular packing, and the absence of bulky structures. The relatively small birefringence mainly results from the flexible thioether linkages structures of the diamine. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 5606–5617, 2007     

Aromatic Polyamides Containing Pendent Acetoxybenzamide Groups

Polycondensation reaction of 5-(4-acetoxy-benzamide) isophthaloylchloride with different aromatic diamines gave a series of polyisophthalamides with good solubility in organic solvents. These polymers showed good thermal stability with initial decomposition temperature above 300 °C and glass transition temperature in the range of 220–335 °C. Thin, flexible, transparent films were cast from solutions, having good electroinsulating properties.