New chitin-based polymer hybrids, 1. Miscibility of poly(vinyl alcohol) with chitin derivatives

As a new class of biopolymer-based hybrid materials, the present paper describes the binary blends of a modified chitin and poly(vinyl alcohol) (PVA) which are miscible in the whole range of compositions. The blend films were prepared by the solvent cast method from a homogeneous aqueous solution of PVA and a chitin derivative having poly(2-methyl-2-oxazoline) side chains. Miscibility between PVA and poly(2-methyl-2-oxazoline) homopolymer was also revealed. Differential scanning calorimetry and FT-IR analyses were used to investigate the blends.     

Effect of poly(vinyl alcohol) fine particles as a novel biodegradable nucleating agent on the crystallization of poly(3‐hydroxybutyrate)

The effect of poly(vinyl alcohol)(PVA) fine particles as the nucleating agent on the crystallization behavior of bacterial poly(3‐hydroxybutyrate)(PHB) was studied using differential scanning calorimetry measurements and polarized light microscope observation. The results were compared with the effect of PVA conventionally blended with PHB. The PVA fine particles were found to be able to greatly enhance the crystallization of PHB, while the conventionally blended PVA extremely retarded the crystallization of PHB. The nucleating effect of PVA fine particles is almost comparable to that of the talc powder. Considering the biodegradability and biocompatibility of PVA, the usage of PVA particle as a nucleating agent provides marked benefits over the currently employed nonbiodegradable nucleating agents, such as talc and boron nitride. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44:1813–1820, 2006     

Miscibility and hydrogen-bonding interactions in biodegradable polymer blends of poly(3-hydroxybutyrate) and a partially hydrolyzed poly(vinyl alcohol)

Miscibility and hydrogen-bonding interactions, as well as the morphological properties, of biodegradable polymer blends of poly(3-hydroxybutyrate) (PHB) and a 80% hydrolyzed poly(vinyl alcohol) (PVA80) were studied using Fourier transform infrared spectroscopy (FTIR) and differential scanning calorimetry (DSC). It was found that PHB is miscible with PVA80 in the amorphous phase over the whole composition range. PVA80 or PHB assumes the amorphous state when its content in the blend is lower than 30 or 20 wt %, respectively. Due to the heavy overlapping of C=O stretching bands from both PVA80 and PHB and the nonmeasurable peak shift in the OH stretching band region, hydrogen-bonding interactions between the OH group of PVA80 and the C=O group of PHB were not detectable at room temperature, but were observed at a higher temperature of 180 degrees C. This is because hydrogen-bonding interactions are promoted above the melting points of these two crystalline polymers, by increasing the mixing entropy and reducing the Deltachi effect. Blending PHB with PVA80 does not have a significant effect on the OH groups of PVA80 that are hydrogen bonded with each other. Instead, the C=O groups of PHB dispossess some of the OH groups that are hydrogen bonded to the C=O groups of PVA80, which gives rise to the miscibility between PVA80 and PHB in the amorphous phase.     

Preparation and characterization of iodinated poly(vinyl alcohol) microfibril

Iodination of poly(vinyl alcohol) (PVA) microfibril, which was obtained from saponification of poly(vinyl pivalate), was conducted before and after zone drawing at various conditions. The resulting PVA microfibrils were characterized by differential scanning calorimeter and scanning electron microscopy. Surface morphologies of these PVA microfibrils showed some differences between PVA microfibril iodinated after and before drawing. Crude shapes of PVA microfibrils iodinated after drawing indicated that iodine decreased the structural regularity severely. On the other hand, PVA microfibrils iodinated before drawing showed relatively ordered surfaces. This was ascribed to the enhanced molecular ordering of PVA microfibrils due on zone drawing. Iodinated PVA microfibrils showed a decrease in crystal melting temperature of about 100°C compared to the untreated sample. PVA microfibrils drawn after iodination showed relatively higher crystal melting temperature than those of microfibrils iodinated after drawing. These results were considered as the proofs of the changes in crystalline lattice of the PVA microfibrils. Effects, of drawing temperature on sublimation of iodine were also evaluated.     

Fabrication of poly(vinyl alcohol)‐graphene quantum dots coated with poly(3,4‐ethylenedioxythiophene) for supercapacitor

Conducting nanofiber composed of poly(vinyl alcohol) (PVA), graphene quantum dots (GQDs) and poly(3,4‐ethylenedioxythiophene) (PEDOT) was prepared for symmetrical supercapacitor through electrospinning and electropolymerization techniques. The formation of PVA nanofibers with the addition of GQDs was excellently prepared with the average diameter of 55.66 ± 27 nm. Field emission scanning electron microscopy images revealed that cauliflower‐like structure of PEDOT was successfully coated on PVA‐GQD electrospun nanofibers. PVA‐GQD/PEDOT nanocomposite exhibited the highest specific capacitance of 291.86 F/g compared with PVA/PEDOT (220.73 F/g) and PEDOT (161.48 F/g). PVA‐GQD/PEDOT also demonstrated a high specific energy and specific power of 16.95 and 984.48 W/kg, respectively, at 2.0 A/g current density. PVA‐GQD/PEDOT exhibited the lowest resistance of charge transfer (R_ct) and equivalent series resistance compared with PEDOT and PVA/PEDOT, indicating that the fast ion diffusion between the electrode and electrolyte interface. PVA‐GQD/PEDOT nanocomposite also showed an excellent stability with retention of 98% after 1000 cycles. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 50–58     

Coupling reaction of poly(α-methylstyryl) anion with (MMA–α-methylstyrene) block copolymer

(MMA–α-methylstyrene)block copolymer was reacted with poly(α-methylstyryl)anion at ?78°C in a mixture of good tetrahydrofuran (THF) and poor methylcyclohexane solvents. The reaction conditions were chosen so as to produce graft copolymers made up of a backbone (AB-type block copolymer) and a single branched chain (1:2 graft copolymer). Gel permeation chromatograph (GPC), osmotic pressure measurement, and elemental analysis were used for the characterization of 1:2 graft copolymer. It appeared that poly(α-methylstyryl)anion reacted with the end pendant groups located farthest away from the branched point of AB-type block copolymer, when the dimensions of AB-type block copolymer molecule are small.     

Compatibility of poly(ethylene oxide)–poly(vinyl acetate) blends

The compatibility of poly(ethylene oxide)–poly(vinyl acetate) (PEO-PVA) blends was examined at five compositions covering the complete range. Samples were prepared by coprecipitation and solution casting. Dynamic mechanical properties were studied at 110 Hz between ?120 and 65°C for dry, quenched, and annealed samples. The study also included tensile testing at 25°C, examination of blend morphology, and DSC measurements at elevated temperatures. Optical microscopy revealed that crystallization of PEO proceeds essentially unhindered at up to 25% poly(vinyl acetate) content by weight. Higher levels of this component drastically reduce spherulite size, and at the highest PVA compositions there was no evidence of crystallization. Thermomechanical spectra of quenched and annealed samples indicate limited mixing of the two components except for the higher (>75%) PVA compositions. Tensile properties show a mutual reinforcement at 10-25% PVA content due to possible polymer segment association. The melting-point depression of PEO is significant above 25% PVA and has been attributed to morphological changes of the PEO crystalline phase.     

Fully-biodegradable poly(3-hydroxybutyrate)/poly(vinyl alcohol) blend films with compositional gradient

Fully-biodegradable bacterial poly(3-hydroxybutyrate) (PHB)/chemosynthetic poly(vinyl alcohol) (PVA) blend films with compositional gradient from one surface to the other surface of the films were prepared by a dissolution-diffusion technique. Three kinds of PVA samples, high- and low-molecular weight atactic PVA and highly syndiotactic PVA (s-PVA), were used in order to investigate the effects of molecular weight and tactic structure on the generation of compositional gradient. The solution of PHB in 1,1,1,3,3,3-hexafluoro-2-propanol (HFIP), which is also a good solvent for PVA, was cast on the PVA film and then the solvent HFIP was evaporated. By selecting the optimum volume of solvent and the evaporation rate, the PHB/PVA blend film with compositional gradient was obtained. The formation of compositional gradient was confirmed by FT-IR microscopy and ATR-FT-IR analysis. The 50%/50% PHB/s-PVA blend film with a nearly ideal compositional gradient, that is, the composition of PHB (or PVA) in the film changing gradually from 100% at one surface to 0% at the other surface of the film was obtained by casting PHB/HFIP solution on to the s-PVA film. Positional dependence of the absorbance of C==O and OH stretching bands along the film thickness direction for the PHB/S-PVA cast films.     

Preparation and properties of poly(vinyl alcohol)–vermiculite nanocomposites

A vermiculite (VMT) dispersion in water was blended with aqueous poly(vinyl alcohol) (PVA). The properties of the PVA–VMT nanocomposites greatly depended on the preparation procedure because of the chemical reactions and physical interactions involved. The samples were prepared in two steps to investigate the properties of the PVA–VMT nanocomposites. The VMT was first pretreated and delaminated with hydrochloric acid. The delaminated VMT was then added to the PVA solution with various mixing times. The structure and properties of the films were investigated. From X‐ray diffraction and transmission electron microscopy, the VMT layers were found to be well dispersed individually in the PVA–VMT blends. The effect of the VMT content on the thermal behavior of the PVA–VMT blends was also studied with differential scanning calorimetry. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 749–755, 2003     

Reinforcement of poly(vinyl alcohol) with chiral poly(amide-imide)s nanoparticles containing S-valine under simple ultrasonic irradiation method

Nanostructured amino acid containing poly(amide-imide) (PAI) was synthesized from the direct polycondensation reaction of 2–(3,5–diaminophenyl)–benzimidazole and N,N′–(pyromellitoyl)–bis–phenylalanine diacid under green condition by using tetrabutylammonium bromide as molten ionic liquid. Field emission scanning electron microscopy images show that the average diameter of polymeric nanoparticles with spherical shape was around 20–35 nm. In the next step, these polymeric nanoparticles were used as nano-fillers for reinforcement of poly(vinyl alcohol) (PVA) for the first time. Bionanocomposite of PVA and various compositions of PAI nanoparticles were produced through ultrasound-assisted technique. Fourier transform infrared spectroscopy, x-ray diffraction, field emission scanning electron microscopy, and thermogravimetric analysis were utilized to characterize the obtained hybrid materials, morphology, and properties. Results of thermal properties indicated that the thermal stability is enhanced. The improvement of thermal properties was attributed to the homogeneous and good dispersion of PAI nanoparticles in the PVA matrix and the strong hydrogen bonding between O–H groups of PVA and the carbonyl of amide and imide groups of the used PAI nanoparticles.     

Modification of hydrophilic poly(vinyl alcohol) film via blending with hydrophobic poly(butyl acrylate-co-methyl methacrylate)

A series of poly(vinyl alcohol)/poly(butyl acrylate-co-methyl methacrylate) [PVA/P(BA-co-MMA)] blend films with different P(BA-co-MMA) content were prepared by the solution casting method. Surface morphologies of the PVA/P(BA-co-MMA) blend films were studied by scanning electron microscopy and atomic force microscopy. Thermal, mechanical, and chemical properties of PVA/P(BA-co-MMA) blend films were investigated by differential scanning calorimeter, thermogravimetric analysis, tensile tests, and surface contact angle tests. It was revealed that the introduction of P(BA-co-MMA) could affect the properties of the PVA films. The results also showed that, when P(BA-co-MMA) mole content is 3 %, the tensile strength and the surface contact angle of the polymer blend film are 20.4 MPa and 43.5°, respectively, suggesting that the polymer blend film holds both a better mechanical property and a better chemical property.     

Study of the miscibility of poly(vinyl pyridines) with poly(vinyl acetate), poly(vinyl alcohol) and their copolymers

Miscibility of poly(4-vinyl pyridine) (P4VP) and poly(2-vinyl pyridine) (P2VP) with poly(viny acetate) (PVAc), poly(vinyl alcohol) PVA and poly(vinyl acetate-co-alcohol) (ACA copolymers) has been investigated over a wide composition range. Differentiaal scanning calorimetry (DSC) results indicate that P2VP is immiscible with PVAC, PVA, and their copolymers over the whole composition range. In turn, P4VP appears to be immiscible with PVAC and PVA, but miscible with some ACA copolymers in certain range of composition. The P4VP-ACA phase diagram for different copolymer compositions has been determined. The variation of the glass transition temperature with composition for miscible mixtures was found to follow the Gordon-Taylor equation, with the parameter κ dependent upon copolymer composition. FTIR analysis of blends reveal the existence of specific interactions via hydrogen bonding between hydroxyl groups and the nitrogen of the pyridinic ring, which appear to be decisive for miscibility. © 1994 John Wiley & Sons, Inc.     

Effect of poly(ethylene oxide) on the structure and properties of poly(vinyl alcohol)

To improve the drawability of poly(vinyl alcohol) (PVA) thermal products, poly(ethylene oxide) (PEO), a special resin with good flexibility, excellent lubricity, and compatibility with many resins, was applied, and the Fourier transform infrared spectroscopy, dynamic mechanical analysis (DMA), differential scanning calorimetry (DSC), and wide‐angle X‐ray diffraction (WXRD) were adopted to study the hydrogen bonds, water states, thermal properties, crystal structure, and nonisothermal crystallization of modified PVA. It was found that PEO formed strong hydrogen bonds with water and PVA, thus weakened the intra‐ and inter‐hydrogen bonds of PVA, changed the aggregation states of PVA chains, and decreased its melting point and crystallinity. Moreover, the interactions among PVA, water, and PEO retarded the water evaporation and made more water remain in the system to plasticize PVA. The existence of PEO also slowed down the melt crystallization process of PVA, however, increased the nucleation points of system, thus made more and smaller spherulites formed. The weakened crystallization capability of PVA and the lubrication of PEO made PVA chains to have more mobility under the outside force and obtain high mechanical properties. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 1946–1954, 2010     

Miscibility,crystallization kinetics,and morphology of poly(β‐hydroxybutyrate) and poly(methyl acrylate) blends

The miscibility, spherulite growth kinetics, and morphology of binary blends of poly(β‐hydroxybutyrate) (PHB) and poly(methyl acrylate) (PMA) were studied with differential scanning calorimetry, optical microscopy, and small‐angle X‐ray scattering (SAXS). As the PMA content increases in the blends, the glass‐transition temperature and cold‐crystallization temperature increase, but the melting point decreases. The interaction parameter between PHB and PMA, obtained from an analysis of the equilibrium‐melting‐point depression, is −0.074. The presence of an amorphous PMA component results in a reduction in the rate of spherulite growth of PHB. The radial growth rates of spherulites were analyzed with the Lauritzen–Hoffman model. The spherulites of PHB were volume‐filled, indicating the inclusion of PMA within the spherulites. The long period obtained from SAXS increases with increased PMA content, implying that the amorphous PMA is entrapped in the interlamellar region of PHB during the crystallization process of PHB. All the results presented show that PHB and PMA are miscible in the melt. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 1860–1867, 2000     

Ordered structures of poly(1H,1H,2H,2H-perfluorodecyl α-substituted acrylate)S

Ordered structures of poly(1H,1H,2H,2H-perfluorodecyl α-fluoroacrylate) (P17FF), poly(α-chloroacrylate) (P17FC), poly(methacrylate) (P17FM) and poly(acrylate) (P17FA) were investigated by X-ray diffraction, DSC and polarizing microscopic observations. At room temperature, both P17FF and P17FC prefer the layered structure of single-layer packing of the fluoroalkyl side chains, while P17FM contains both single-layer and double-layer packing, and P17FA forms double-layer packing. As temperature increases, particularly in P17FF and P17FC, there was observed a structural rearrangement of the single-layer packing to double-layer one accompanied by melting of the side chain crystallites, which may come from an intermolecular interaction between the main chains caused by polar effect of the α-substituents.     

The role of hydrogen-bonding interaction in poly(vinyl alcohol)/poly(acrylic acid) blending solutions and their films

<正>The aim of this work is to investigate the hydrogen-bonding interaction in poly(vinyl alcohol)(PVA)/poly(acrylic acid)(PAA) blending system and its influence on rheological properties in solution and the physical properties in solid state. Introducing PAA into PVA solutions resulted in a thickening behavior of blend solutions.The viscosity of the solutions increased with PAA content increasing,and a maximum viscosity could be obtained when the ratio of PVA/PAA was 70/30. The intermolecular hydrogen-bonding and miscibility between PVA and PAA in solid state were investigated by differential scanning calorimetry(DSC),Fourier transform infrared spectroscopy(FTIR) and mechanical measurements.The results displayed the great influence of introducing PAA on the properties of blending films.The tensile strength increased from 89.31 MPa to 119.8 MPa and Young's modulus improved by over 300%with increasing PAA concentration compared with those of pure PVA films.By systematically studying the rheological behaviors of solutions and the physical properties of films,the influence of hydrogen-bonding in solutions and solid states were discussed.     

Nuclear magnetic relaxation of α-13C nuclei of helical poly(γ-hexyl-L-glutamate) and poly(γ-benzyl-L-glutamate)

Spin-lattice relaxation times (T₁), spin-spin relaxation times (T₂), and nuclear Overhauser enhancements (NOE), at 75.5 MHz are reported for α-¹³C nuclei of poly (γ-benzyl-L -glutamate) in deuterated dimethylformamide at 60°C and of poly(γ-hexyl-L -glutamate) in cyclohexanone at 48 and 79°C. It is shown that for molecular weights above 10⁵, the polypeptides cannot be considered as essentially rigid helices with internal librational motions; additional backbone flexing motions contribute to the relaxation behavior.     

Stereoregularity of poly(methyl α-chloroacrylate)

Triad and tetrad tacticities of poly(methyl α-chloroacrylate) and poly(methyl α-chloroacrylate-β-d₁) were determined by nuclear magnetic resonance (NMR) spectroscopy. Methyl α-chloroacrylate-β-d₁ and its polymer were first synthesized. Isotactic poly(methyl α-chloroacrylate) was prepared with ethylmagnesium chloride-benzal-acetophenone in combination as catalyst. The syndiotacticity of radically polymerized polymers increased with decreasing polymerization temperature. For radical polymerization, enthalpy and entropy differences between isotactic and syndiotactic additions were calculated to give ΔH ? ΔH = 850 cal/mole and ΔS ? ΔS = 0.93 eu. The stereoregularity of the polymer prepared with phenylmagnesium bromide catalyst was analyzed in fairly good agreement with first-order Markov statistics, while polymerization with fluorenyllithium seems predominantly to proceed by a mechanism similar to free-radical mechanism. Stereoregularity-controlling power for individual substituents is briefly discussed.     

Preparation of poly(vinylalcohol)/poly(acrylamide‐co‐vinyl imidazole)/γ‐Fe2O3 semi‐IPN nanocomposite and their application for removal of heavy metal ions from water

A series of magnetic semi‐interpenetrating polymer network (semi‐IPN) hydrogels was prepared in one‐stage strategy composed of linear poly(vinyl alcohol) (PVA) chains and magnetic γ‐Fe₂O₃ nanoparticles entrapped within the cross‐linked poly(acrylamide‐co‐vinylimidazole) (poly(AAm‐co‐VI)) network. The influence of PVA, weight ratio of AAm:VI, γ‐Fe₂O₃, and MBA on the swelling properties of the obtained nanocomposite hydrogels was evaluated. The prepared magnetic semi‐IPN hydrogels were fully characterized and used as absorbent for removal of Pb(II) and Cd(II) from water. Factors that influence the metal ion adsorption such as solution pH, contact time, initial metal ion concentration, and temperature were studied in details. The experimental results were reliably described by Langmuir adsorption isotherms. The adsorption capacity of semi‐IPN nanocomposite for Pb(II) and Cd(II) were175.80 and 149.76 mg g^?1, respectively. The kinetic experimental data indicated that the chemical sorption is the rate‐determining step. According to thermodynamic studies, Pb(II) and Cd(II) adsorption on the hydrogels was endothermic and also chemical in nature. The prepared magnetic PVA/poly(AAm‐co‐VI) semi‐IPN hydrogels could be employed as efficient and low‐cost adsorbents of heavy metal ions from water. Copyright © 2016 John Wiley & Sons, Ltd.     

Miscible blends of poly(ethylene oxide) with brush copolymers of poly(vinyl alcohol)‐graft‐poly(l‐lactide)

Even though poly(ethylene oxide) (PEO) is immiscible with both poly(l ‐lactide) (PLLA) and poly(vinyl alcohol) (PVA), this article shows a working route to obtain miscible blends based on these polymers. The miscibility of these polymers has been analyzed using the solubility parameter approach to choose the proper ratios of the constituents of the blend. Then, PVA has been grafted with l ‐lactide (LLA) through ring‐opening polymerization to obtain a poly(vinyl alcohol)‐graft‐poly(l ‐lactide) (PVA‐g‐PLLA) brush copolymer with 82 mol % LLA according to ¹H and ¹³C NMR spectroscopies. PEO has been blended with the PVA‐g‐PLLA brush copolymer and the miscibility of the system has been analyzed by DSC, FTIR, OM, and SEM. The particular architecture of the blends results in DSC traces lacking clearly distinguishable glass transitions that have been explained considering self‐concentration effects (Lodge and McLeish) and the associated concentration fluctuations. Fortunately, the FTIR analysis is conclusive regarding the miscibility and the specific interactions in these systems. Melting point depression analysis suggests that interactions of intermediate strength and PLOM and SEM reveal homogeneous morphologies for the PEO/PVA‐g‐PLLA blends. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016 , 54, 1217–1226