聚酰亚胺／聚N－乙烯吡咯烷酮分子复合物的合成和表征

由原位缩聚制备了刚性高分子聚酰亚胺（ＰＩ）和柔性基体聚Ｎ－乙烯吡咯烷附（ＰＶＰ）的分子复合物，并由实验证明了中间体聚酰胺酸（ＰＡ）和聚乙烯吡咯烷酮大分子之间存在的酸一碱相互作用．这种相互作用促进了混容性，使聚酰亚胺能以分子水平或接近分子水平分散在聚毗咯烷酮的基体之中．聚酰亚胺／聚Ｎ－乙烯吡咯烷团分子复合物的薄膜呈透明性，在整个组成范围内只有一个Ｔｇ，显示单相行为。当ＰＩ含量＜２０％时，ＳＥＭ相片呈现均相形貌，看不到ＰＩ微晶．广角Ｘ－ｒａｙ衍射图表明ＰＩ特征结晶峰消失，和无定形的ＰＶＰ完全混容．当ＰＩ含量＞４０％，ＳＥＭ显示有均匀分布的、棒状ＰＩ微晶存在．通过分子复合，即使ＰＩ含量为１０％，聚Ｎ－乙烯吡咯烷酮不再溶于乙醇，耐热性也有提高．     

聚酰亚胺／聚N－乙烯吡咯烷酮分子复合物的合成和表征

由原位缩聚制备了刚性高分子聚酰亚胺（ＰＩ）和柔性基体聚Ｎ－乙烯吡咯烷附（ＰＶＰ）的分子复合物，并由实验证明了中间体聚酰胺酸（ＰＡ）和聚乙烯吡咯烷酮大分子之间存在的酸一碱相互作用．这种相互作用促进了混容性，使聚酰亚胺能以分子水平或接近分子水平分散在聚毗咯烷酮的基体之中．聚酰亚胺／聚Ｎ－乙烯吡咯烷团分子复合物的薄膜呈透明性，在整个组成范围内只有一个Ｔｇ，显示单相行为。当ＰＩ含量＜２０％时，ＳＥＭ相片呈现均相形貌，看不到ＰＩ微晶．广角Ｘ－ｒａｙ衍射图表明ＰＩ特征结晶峰消失，和无定形的ＰＶＰ完全混容．当ＰＩ含量＞４０％，ＳＥＭ显示有均匀分布的、棒状ＰＩ微晶存在．通过分子复合，即使ＰＩ含量为１０％，聚Ｎ－乙烯吡咯烷酮不再溶于乙醇，耐热性也有提高．     

聚酰亚胺的微球化

依据缩聚反应的特点, 提出了一条聚酰亚胺微球的有效制备路线, 通过在缩聚溶液和沉淀剂中加入聚乙烯基吡咯烷酮(PVP)改变体系特性. 探讨了PVP及沉淀剂对微球形貌、粒径及分布的影响. 结果表明, 在二胺与二酐缩聚溶液中加入PVP可以得到较好的球形聚合物颗粒; 增加PVP含量, 微球粒径减小且分布均匀, 而分子量有所降低; 以水为沉淀剂所得微球的形貌优于乙醇沉淀剂, 并且随着PVP用量的增加, 微球粒径减小, 均匀性亦随之提高. PVP在制备过程中分别呈现出成核、成球及分散稳定的作用, 从而实现了聚酰亚胺材料在微米尺度上的微球化.     

High-molecular-weight poly(amino acid)s by the direct polycondensation reaction promoted by triphenyl phosphite and LiCl in the presence of polyvinylpyrrolidone

Poly(α-amino acid)s of high molecular weight were obtained by the direct polycondensation reaction of α-amino acids in the presence of polyvinylpyrrolidone (PVP) as a matrix of triphenyl phosphite and LiCl in N-methylpyrrolidone (NMP). Molecular weights of the polymer produced were improved by use of an increasing amount of matrix of higher molecular weight. Most favorable results were obtained by the reaction at 80°C for 16 hr at a monomer concentration of 0.33 mole/liter in a NMP solution that contained about 3 wt % LiCl in the presence of an equivalent unit mole of PVP with the molecular weight of 3.6 x 10⁵. The polymer from β-alanine with high molecular weight, which is difficult to obtain by the NCA method, was easily prepared by this process.     

Structural changes of silver polymer electrolytes: Comparison between poly(2‐ethyl‐2‐oxazoline) and poly(N‐vinyl pyrrolidone) complexes with silver salt

The difference between the polymer matrices of poly(2‐ethyl‐2‐oxazoline) (POZ) and poly(N‐vinyl pyrrolidone) (PVP) does not have a significant effect on the facilitated propylene transport and propylene solubility in 1:1 polymer/silver salt complex membranes, according to our previous work. In this article, its origin is investigated in terms of both microstructures of silver polymer electrolytes and the coordinative interaction of silver ion with polymer and with the counteranion. Initially different microstructures of POZ and PVP become similar to each other upon dissolving a large amount of silver salt, as evidenced by propane transport properties, specific volume, and Bragg d‐spacing. The dissolution of the silver salt in the polymer solvent strongly depends on the coordinative interaction between silver ion and carbonyl oxygen of POZ and PVP. Thus, the structural similarity upon dissolving silver salts in POZ and PVP is primarily determined by the coordinative interaction between silver ion and carbonyl oxygen, which was confirmed by theoretical structure calculation based on density functional theory and by IR and Raman spectroscopy. Therefore, facilitated olefin transport for silver polymer electrolyte membranes does not strongly depend on the polymeric matrix at high silver concentrations. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 232–237, 2004     

Molecular simulation studies on the interaction between different polymers in aqueous solution

A molecular dynamics simulation was performed to investigate the aggregates of mixing and the interaction between different polymers in aqueous solution. These polymers include partially hydrolyzed polyacryamide (HPAM), hydroxyethylcellulose (HEC) and polyvinylpyrrolidone (PVP). The structures of mixed aggregates were analyzed from the dihedral angle distribution of: (1) pure HPAM; (2) HPAM in aqueous solution; (3) HPAM with small segments of PVP or HEC in aqueous solution. At the same time, the simulated IR spectra and the calculated interaction parameters were used to distinguish the different interactions between HPAM and PVP or HEC. In order to confirm the validity of the simulated predictions, experimental IR spectra of polymer systems were made, and the specific viscosity of the HPAM and PVP or HEC system was measured using capillary viscometry. It can be seen from the viscosity measurements that the viscosity of the HPAM/PVP system in aqueous solution decreases linearly with an increase in concentration of PVP, whereas a maximum viscosity value appears with the increase in concentration of HEC in the HPAM/HEC system. The conclusion was drawn that the interaction between HPAM and HEC is stronger than the one between HPAM and PVP, and that molecular simulation can be considered as an adjunct to experiments and can provide otherwise inaccessible (or, not easily accessible) microscopic information that experimentalists can use.     

聚合物PVP与表面活性剂AOT相互作用的介观模拟

用耗散颗粒动力学模拟(DPD)方法研究了聚乙烯吡咯烷酮(PVP)与2-乙基己基琥珀酸酯磺酸钠(AOT)之间的相互作用.在三维模拟格子中,聚合物链均方末端距〈r²〉随着表面活性剂浓度的增加呈现一种首先减小,接着增加,然后又减小的趋势.构型和结构分析表明,AOT的加入能够引起聚合物链的二面角分布发生改变,这意味着AOT与PVP产生了相互作用.同时表面活性剂/聚合物体系的聚集形态也可以在DPD三维模拟格子中直观显现出来.     

Unique fluorescence behavior of perylenetetracarboxydiimides in polyimide systems

Perylenetetracarboxydiimide (PEDI) molecularly dispersed in polyamic acid (PAA) and polyimide (PI) films has unique fluorescence properties. An originally strong fluorescence of PEDI is efficiently quenched in the PAA films. The systematic variation of the chain structure of the PAA matrices revealed that the aromatic amide groups in the PAA chains function as a quencher. When a PAA derived from 3,4,3′4′-biphenyltetracarboxylic dianhydride (BPDA) and p-phenylenediamine (PDA), BPDA/PDA, was used as a matrix polymer, the fluorescence of the dye dispersed in the film increased abruptly as imidization of the matrix proceeds. But annealing at temperatures higher than 320°C in the step-heating process caused a gradual decrease in the fluorescence intensity. The decreased intensity results from the dye–PDA units interactions intensified by the denser molecular packing of the matrix polymer chains. PEDI shows significant dependence of the fluorescence intensity on the chain structure of the PI matrices. In the various PI films containing a fixed diamine component, the dye fluorescence intensity reduces linearly with an increase in the intramolecular charge transfer ability of the PI matrices. From the result, we propose a fluorescence quenching mechanism through multistep electron transfer processes. The BPDA/PDA polyimide matrix leads to a strong PEDI fluorescence whereas the pyromellitic dianhydride (PMDA)-based PI matrices do not. For the blends composed of these PIs, the fluorescence of PEDI bound into the main chains provides a valuable indicator of the miscibility on the molecular level. © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36: 827–840, 1998     

Electronic effect of polymeric environments on metalloporphyrins

Electronic modulations brought about on ionic metalloporphyrins by various polymeric environments were investigated in detail with spectral analysis. The porphyrins employed were metalloderivatives of anionic p‐sulfonated tetraphenylporphyrins [MTPPS; M = Cu(II), Zn(II), Ag(II), and Cd(II)]. The polymer system chosen involved poly(4‐vinylpyridine) (PVP), crosslinked and linear polystyrenes partially chloromethylated and quaternized (PS and PS′), and polyethylene glycol (PEG). These were expected to interact with MTPPS through a coordinate bond on its central metal atom (PVP), through Coulombic attraction (PS and PS′), or through ion–dipolar interaction (PEG). Significant changes in the electronic spectra (redshifts in both B and Q bands) were seen in polymer‐incorporated MTPPS in comparison with free MTPPS. For a given metalloporphyrin, the order of the spectral shifts was always MTPPS < PEG–MTPPS < PVP–MTPPS < PS–MTPPS < PS′–MTPPS. Furthermore, for a given polymer matrix, the extent of spectral variation was metal‐dependent: Cd > Zn > Ag > Cu. This is explained in terms of the molecular distortions and associated changes in the metalloporphyrin orbital overlap and the charge delocalization from the peripheral substituents or coordinating ligand functions to the porphyrin π framework. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 39: 326–334, 2001     

Reaction of a low‐molecular‐weight free radical with a flexible polymer chain: Kinetic studies on the OH + poly(N‐vinylpyrrolidone) model

This work addresses the issue of kinetics of diffusion‐controlled reactions of small radicals with macromolecules in solution. Attack of pulse‐generated hydroxyl radicals on poly(N‐vinylpyrrolidone)—PVP—chains of various molecular weight in water was used as the model reaction. Pulse radiolysis with spectrophotometric detection was applied to determine the rate constants by competition kinetics. The rate constant depends both on polymer concentration and on its molecular weight. In dilute solutions, a distinct dependence of the rate constant on the molecular weight is observed. In the studied range of molecular weight, the values of reaction radius, calculated using Smoluchowski equation on the basis of experimental kinetic data, are very close to the radius of gyration of polymer coils. We believe that radius of gyration, as an easily determined parameter, could possibly serve for predicting rate constants of diffusion‐controlled reactions of polymers with low‐molecular‐weight compounds in dilute solutions. With increasing polymer concentration and thus increasing spatial overlap of polymer coils the dependence of the rate constant on the molecular weight fades away, and the rate constant values increase with increasing concentration toward the value determined for low‐molecular‐weight model of PVP. Most steep increase approximately coincides with the hydrodynamic critical concentration of a given PVP sample, reflecting the change in reaction geometry from individual coils to a continuous matrix of interpenetrating chains. © 2011 Wiley Periodicals, Inc. Int J Chem Kinet 43: 474–481, 2011     

Recalcitrance of poly(vinylpyrrolidone): evidence through matrix-assisted laser desorption-ionization time-of-flight mass spectrometry.

The aerobic biodegradability of an extensively used synthetic polymer was monitored the first time on a laboratory-scale fixed-bed bioreactor (FBBR) applying matrix-assisted laser desorption-ionization time-of-flight mass spectrometry (MALDI-TOF MS). Polymeric poly(vinylpyrrolidone) (PVP) was spiked at concentrations of 10 mg l(-1) onto the FBBR run with river water and the biodegradation monitored after lyophilization of aliquots of the test liquor applying MALDI-TOF-MS. The latter proved to be a powerful tool for qualitative screening purposes of PVP in a molecular mass range <20 kDa in particularly yielding a high sensitivity and shot-to-shot reproducibility. The sample-to-sample reproducibility was enhanced applying the anchor target device. Post-source decay-MALDI-TOF-MS fragmentation investigations determined the unknown end groups of PVP unambiguously. Poor biodegradability of PVP can be assumed, since even after 30 days, no oxidation of the terminal groups and no difference in the repeating units was observed. A decrease in the molecular mass distribution can be drawn back rather to adsorption of PVP in the FBBR other than to biodegradation. This was further investigated performing an adsorption experiment with sewage sludge as solid matrix and analyses of the aqueous phase and sludge samples. Extrapolating these results to the situation in wastewater treatment plants, it is highly likely that PVP is eliminated from the dissolved phase by adsorption onto sludge particles.     

Correlations between the free-volume properties and the miscibility of chitosan/polar polymers blend membranes

The miscibility of chitosan (CS)/polar polymer blend membranes has been studied by positron annihilation and other methods. The miscibility of these two blend systems (CS/polyvinyl pyrrolidone (PVP) and CS/polyethylene glycol (PEG)) is good in the solution state due to the hydrogen interaction between the functional groups of the studied polymers. However, the miscibility of these two blend systems in the solid state is better in the CS/PVP system than in the CS/PEG system. The differences in miscibility of such two blend systems in the solid state were powerfully demonstrated with positron annihilation lifetime spectroscopy (PALS) methods. The CS/PEG blend system had much larger free-volume size and lower free-volume concentration. For their poorer interaction and phase separation fact, the molecules in the interfacial zone of the CS/PEG blend are less compact than the CS matrix. Therefore, the free-volume size in the interfacial zone was much larger than it in the CS matrix.     

Interaction of collagen and poly(vinyl pyrrolidone) in blends

The interaction between collagen and poly(vinyl pyrrolidone) (PVP) in blends has been studied by viscometry, differential scanning calorimetry (DSC) and by Fourier transform infrared spectroscopy (FTIR). It was found that the amide A and amide I bands position in FTIR spectra of collagen were shifted after blending with PVP to higher wavenumbers. DSC measurements showed different melting temperature, glass transition temperature and enthalpy for the blends and for the single components. Viscosity measurements showed interaction between collagen and PVP also in a dilute water solution.The results have shown, that the interactions between collagen and PVP exist due to the strong interactions between the synthetic and biological component, mainly by hydrogen bonds. These interactions caused that collagen and PVP are miscible at molecular level. The blending of collagen with PVP may give the possibility of producing new materials for potential biomedical applications.     

Radical Polymerization of Maleic Acid by Potassium Persulfate in the Presence of Polyvinylpyrrolidone in Water

Maleic acid(MA) was found to polymerize easily by potassium persulfate (KPS) in water in the presence of polyvinylpyrrolidone (PVP), and to form a polymer complex in which the molar ratio of MA to VP monomer unit was approximately unity. The formation of the polymer complex was accelerated by increases in the reaction temperature, in the concentrations of KPS and MA, and in the molecular weight of PVP used. Thermal degradation behavior of the polymer complex was studied thermo-gravimetrically. The thermagram of the polymer complex was substantially different from those of PVP and the 1:1 mixture of MA and PVP. It was found that the poly-MA portion of the polymer complex decomposed at 100-300°C, while the PVP portion underwent degradation at 350-500°C. In order to separate poly-MA from the polymer complex, the polymer complex was methylated by diazomethane, and 50 ～ 60% of the poly-MA part in the polymer complex was separated as its methyl ester, which was found to be oligomer (M = 400 ～ 500) by GPC. Unseparated part of poly-MA seems to be grafted onto PVP. The polymerization of citraconic acid (CA) was also performed in the same manner. Similar results were obtained, though the polymerization of CA was slower as compared with that of MA.     

Preparation and characterization of polyvinylidene fluoride (PVDF) hollow fiber membranes

Polyvinylidene fluoride (PVDF) hollow fiber membranes were prepared by dry/wet and wet phase inversion methods. In spinning these PVDF hollow fibers, dimethylacetamide (DMAc) and polyvinyl pyrrolidone (PVP) were used as a solvent and an additive, respectively. Water was used as the external coagulant. Water or ethanol was used as the internal coagulants. The membranes were characterized in terms of water flux, molecular weight cut-off for the wet membranes. Gas permeation fluxes and effective surface porosity were determined by a gas permeation method for the dried membranes. The cross-sectional structures were examined by scanning electron microscopy. The effects of polymer concentration, air-gap, PVP molecular weight, PVP content in the polymer dope, and the internal coagulant on the permeation properties and membrane structures were examined. Highly permeable PVDF hollow fiber membranes could be prepared from a polymer dope containing low molecular weight PVP and using ethanol as the internal coagulant.     

Length scale of polyisopirene and dynamic light scattering and structure of sodium-2-diethylhexyl sulfosuccinate/water/decane

The mixture of polyisopirene (PI) and sodium-2-diethylhexyl sulfosuccinate /decane/water microemulsion (ME) at AOT to water molar ratio (X = 30) and droplet mass fraction (m_f,drop = 0.08) was studied with dynamic light scattering and small-angle X-ray scattering (SAXS). The light scattering was used to obtain the diffusion coefficient of Brownian motion of the nano-droplets at different polymer concentrations and molecular weights (1000 and 4700) in the ME. The dynamics of the nano-droplets decreased with the increase of molecular weight (from 1000 to 4700) and concentration (from 0.01 to 0.09) of PI. The study of the structure by SAXS showed that with increase of PI (MW = 1000) mass fraction from 0.01 to 0.09 at ME, the size of the droplets changes from 4.5 to 4.3 nm and with increase of PI (MW = 4700) concentration at ME, the size of droplets changes from 4.8 to 4.4 nm. The size ratio of droplets to polymer decreased with increase of concentration and molecular weight of polymer and also the interaction between the droplets increased with increase of polymer concentration.     

Thermodynamics of interaction between sodium bis(2‐ethylhexyl) sulfosuccinae and polymers in aqueous solutions by isothermal titration microcalorimetry

The interactions between sodium bis(2‐ethylhexyl) sulfosuccinae (AOT) and two nonionic water‐soluble polymers, including polyvinyl pyrrolidone (PVP) and polyethylene glycol (PEG) have been investigated by using isothermal titration microcalorimetry in aqueous solutions at 298.15 K. The results show that the critical aggregation concentration, which corresponding to the first turning point in the curve of experimental interaction heat versus concentration of the surfactant, is lower than the critical micellar concentration (cmc), confirming the existence of polymer‐surfactant interactions. The value of cac is not sensitive to the relative amount of polymer in low concentration range of the polymer. The mono‐layer saturated adsorption concentration, which corresponding to the second turning point, rises as the polymer concentration is increased. The interaction between PVP and AOT is stronger than that between PEG and AOT. The results also indicate that the aggregation of AOT in water and polymers solutions is entropically driven. The observed thermal effects have been interpreted in terms of the interactions of the polymer molecules with AOT monomers or the molecular clusters. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 275–283, 2006     

Effect of water-soluble polymers, polyethylene glycol and poly(vinylpyrrolidone), on the gelation of aqueous micellar solutions of Pluronic copolymer F127

The micellization of F127 (E(98)P(67)E(98)) in dilute aqueous solutions of polyethylene glycol (PEG6000 and PEG35000) and poly(vinylpyrrolidone) (PVP K30 and PVP K90) is studied. The average hydrodynamic radius (r(h,app)) obtained from the dynamic light scattering technique increased with increase in PEG concentration but decreased on addition of PVP, results which are consistent with interaction of the micelles with PEG and the formation of micelles clusters, but no such interaction occurs with PVP. Tube inversion was used to determine the onset of gelation. The critical concentration of F127 for gelation increased on addition of PEG and of PVP K30 but decreased on addition of PVP K90. Small-angle X-ray scattering (SAXS) was used to show that the 30 wt% F127 gel structure (fcc) was independent of polymer type and concentration, as was the d-spacing and so the micelle hard-sphere radius. The maximum elastic modulus (G(max)(')) of 30 wt% F127 decreased from its value for water alone as PEG was added, but was little changed by adding PVP. These results are consistent with the packed-micelles in the 30 wt% F127 gel being effectively isolated from the polymer solution on the microscale while, especially for the PEG, being mixed on the macroscale.     

Polycondensation reaction of dimethyl tartrate with hexamethylenediamine in the presence of various matrices

The polycondensation reaction of dimethyl tartrate (DMT) with hexamethylenediamine (HMD) was carried out in dimethyl sulfoxide (DMSO) at 60°C in the presence of various polymer matrices, which were expected to interact with DMT or the resulting polyamide which had pendant hydroxyl groups due to hydrogen bonding. It was found that the rate of polycondensation was enhanced by polymer matrices such as poly(vinyl pyrrolidone) (PVP), Pullulan (polysaccharide) (PF), and poly(vinyl alcohol) (PVA). The rate enhancement became more pronounced with increasing molecular weight of the polymer matrix. When polycondensation in the presence of PVA was carried out in DMSO, a polymer complex was produced. The formation of the polymer complex between the resulting polyamide and PVA during polycondensation was dependent on the concentration of monomers and also on PVA; a gelation of the solution was observed at a concentration of PVA.     

Spectroscopic and Discharge Studies on Graphene Oxide Doped PVA/PVP Blend Nanocomposite Polymer Films

Graphene oxide (GO) nanoparticles were synthesized by modified Hummers method. The synthesized GO nanoparticles were incorporated in polyvinyl alcohol/polyvinyl pyrrolidone (PVA/PVP) blend polymers for the preparation of nanocomposite polymer films by solution cast technique. Different characterizations such as XRD, UV–Vis and FTIR were carried-out on to the prepared nanocomposite polymer films. The thermal analysis of the films was studied by DSC. The morphology of PVA/PVP:GO polymer films confirms GO was exfoliated within the PVA/PVP matrix and also reveals the heterogeneous phase of nanocomposite polymer electrolyte systems. From the conductivity studies the highest conductivity of PVA/PVP: GO (0.45: 0.3) was found to be 8.05 × 10^–4 S/cm at room temperature. Solid state battery has been fabricated with the configuration of Mg⁺/(PVA/PVP:GO)/(I₂ + C + electrolyte) and its cell parameters were calculated for a constant load of 100 kΩ.