Thermal degradation of poly(4-chloromethyl-α-acetoxystyrene) and poly(4-chloropropyl-α-acetoxystyrene)

The thermal degradation behaviour of two poly(4-ω-chloroalkyl-α-acetoxystyrene)s has been studied by means of dynamic and isothermal thermogravimetric analysis and gas chromatography-mass spectroscopy. The results show that two reactions occur during the first stage of the process. An elimination reaction gives acetic acid as major volatile species and a residue formed of para-substituted polyphenylacetylenes. A depolymerization reaction gives principally the para-substituted acetophenone corresponding to the starting monomer, and explains the low molecular weights of the residues. These two reactions are simultaneous in the case of poly(4-chloromethyl-α-acetoxystyrene), but are distinguishable in the case of poly(4-3-chloropropyl-α-acetoxystyrene). Kinetic parameters of the overall decomposition of these two polymers have been calculated and compared with those of poly(4-2-chloroethyl-α-acetoxystyrene).     

Living cationic polymerization of vinyl ethers with a urethane group

To study the possibility of living cationic polymerization of vinyl ethers with a urethane group, 4‐vinyloxybutyl n‐butylcarbamate ( 1 ) and 4‐vinyloxybutyl phenylcarbamate ( 2 ) were polymerized with the hydrogen chloride/zinc chloride initiating system in methylene chloride solvent at ?30 °C ([monomer]₀ = 0.30 M, [HCl]₀/[ZnCl₂]₀ = 5.0/2.0 mM). The polymerization of 1 was very slow and gave only low‐molecular‐weight polymers with a number‐average molecular weight (M_n) of about 2000 even at 100% monomer conversion. The structural analysis of the products showed occurrence of chain‐transfer reactions because of the urethane group of monomer 1 . In contrast, the polymerization of vinyl ether 2 proceeded much faster than 1 and led to high‐molecular‐weight polymers with narrow molecular weight distributions (MWDs ≤ ～1.2) in quantitative yield. The M_n's of the product polymers increased in direct proportion to monomer conversion and continued to increase linearly after sequential addition of a fresh monomer feed to the almost completely polymerized reaction mixture, whereas the MWDs of the polymers remained narrow. These results indicated the formation of living polymer from vinyl ether 2 . The difference of living nature between monomers 1 and 2 was attributable to the difference of the electron‐withdrawing power of the carbamate substituents, namely, n‐butyl for 1 versus phenyl for 2 , of the monomers. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 2960–2972, 2004     

Living cationic polymerization of 2-vinyloxyethyl phthalimide: Synthesis of poly(vinyl ether) with pendant primary amino functions

Cationic polymerization of 2-vinyloxyethyl phthalimide ( 1 ) in CH₂Cl₂ at ?15°C with hydrogen iodide/iodine (HI/I₂) as initiator led to living polymers of a narrow molecular weight distribution (M?_w/M?_n = 1.1–1.25). The number-average molecular weight of the polymers was in direct proportion to monomer conversion and could be controlled in the range of 1000–6000 by regulating the 1 /HI feed ratio. However, when a fresh monomer was supplied to the completely polymerized reaction mixture, the molecular weight of the polymers was not directly proportional to monomer conversion. The polymerization of 1 by boron trifluoride etherate (BF₃OEt₂) in CH₂Cl₂ at ?78°C gave polymers with relatively high molecular weight (M?_w > 20,000) and broad molecular weight distribution (M?_w/M?_n ～ 2). The HI/I₂-initiated polymerization of 1 was an order of magnitude slower than that of ethyl vinyl ether, probably because of the electron-withdrawing phthalimide pendant. Hydrazinolysis of the imide functions in poly( 1 ) gave a water-soluble poly(vinyl ether) ( 3 ) with aliphatic primary amino pendants.     

Living cationic polymerization of vinyl ether with a cyclic acetal group

The living cationic polymerization of 5‐ethyl‐2‐methyl‐5‐(vinyloxymethyl)‐1,3‐dioxane ( 1 ), a vinyl ether with a cyclic acetal unit, was investigated with various initiating systems in toluene or methylene chloride at 0 to ?30 °C. With initiating systems such as hydrogen chloride (HCl)/zinc chloride (ZnCl₂), isobutyl vinyl ether–acetic acid adduct [CH₃CH(OiBu)OCOCH₃]/tin tetrabromide (SnBr₄)/di‐tert‐butylpyridine (DTBP), and CH₃CH(OiBu)OCOCH₃/ethylaluminum sesquichloride (Et_1.5AlCl_1.5)/ethyl acetate (CH₃COOEt), the number‐average molecular weights (M_n's) of the obtained poly( 1 )s increased in direct proportion to the monomer conversion and produced polymers with relatively narrow molecular weight distributions [MWDs; weight‐average molecular weight/number‐average molecular weight (M_w/M_n) = 1.2–1.3]. To investigate the living nature of the polymerization with CH₃CH(OiBu)OCOCH₃/SnBr₄/DTBP, a second monomer feed was added to the almost polymerized reaction mixture. The added monomer was completely consumed, and the M_n values of the polymers showed a direct increase against the conversion of the added monomer, indicating the formation of a long‐lived propagating species. The glass transition temperature and thermal decomposition temperature of poly( 1 ) (e.g., M_n = 13,600, M_w/M_n = 1.30) were 29 and 308 °C, respectively. The cyclic acetal group in the pendants of the polymer of 1 could be converted to the corresponding two hydroxy groups in a 65% yield by an acid‐catalyzed hydrolysis reaction. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 4855–4866, 2007     

Soluble tin(II) macroinitiator adducts for the controlled ring‐opening polymerization of lactones and cyclic carbonates

Polyesters and poly(ester carbonates) were synthesized via ring‐opening polymerization with new tin(II) macroinitiator adducts containing oligomeric L ‐lactide (LLA), rac‐lactide (rac‐LA), and ?‐caprolactone (CL). The novel initiating species were synthesized by the reaction of LLA, rac‐LA, or CL with Sn(OEt)₂ (monomer concentration/initiator concentration ≤20) and then were dissolved in methylene chloride or toluene and stored in a stoppered flask for the subsequent ring‐opening polymerization of cyclic esters and carbonates. The soluble tin alkoxide macroinitiators yielded predictable and quantitative initiation of polymerization for up to 1 month of storage time at room temperature. The resulting polymers displayed low polydispersity (≤1.5), and a high monomer conversion (>95%) was obtained within relatively short polymerization times (≤2 h). Adjusting the monomer/macroinitiator ratio effectively controlled the molecular weights of the polymers. NMR was used to characterize the initiating species and polymer microstructure, and size exclusion chromatography was used to determine the molecular weight properties of the polymers. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 3434–3442, 2002     

Design and property of thermoresponsive core–shell fluorescent nanoparticles via RAFT polymerization and suzuki coupling reaction

The polymerization of a 2,7‐dibromocarbazole‐containing functional monomer, 6‐(2,7‐dibromo‐9H‐carbazol‐9‐yl)hexyl methacrylate (DBCzMA), was successfully carried out via the reversible addition‐fragmentation chain transfer (RAFT) technology. The polymerization behavior possessed the feature of “living”/controlled radical polymerization, for example, the first‐order kinetics, the linear increase of the molecular weight of the polymer with the monomer conversion and relatively narrow molecular weight distribution (M_w/M_n ≤ 1.27). The amphiphilic copolymers, poly(DBCzMA_m‐b‐NIPAM_n), with different chain length of poly(DBCzMA) and poly(N‐isopropylacrylamide) (PNIPAM), were successfully prepared via RAFT chain‐extension reaction, using poly(DBCzMA) as the macromolecular chain transfer agent (macro‐CTA) and NIPAM as the second monomer. Modification of 2,7‐dibromide groups in amphiphilic copolymer poly(DBCzMA‐b‐NIPAM) via Suzuki coupling reaction employed 2,7‐bis(4′,4′,5′,5′‐tetramethyl‐1′,3′,2′‐dioxaborolan‐2′‐yl)‐N?9″‐heptadecanylcarbazole as the other reaction material to afford a poly(2,7‐carbazole)‐containing crosslinked materials. The stable and uniform core–shell fluorescent nanoparticles were successfully prepared in water. The formed fluorescent nanoparticles showed good thermoresponsive properties, which is confirmed by dynamic light scattering observation. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013 , 51, 4021–4030     

Branched polymers through redox emulsion polymerization using peroxide monomer as the branching agent

Redox emulsion polymerization to branched vinyl polymers in the presence of 2-(tert-butylperoxy)ethyl methacrylate (BPEMA), ferrous sulfate, and sodium formaldehyde sulfoxylate (SFS) is reported in this paper. The peroxide monomer BPEMA containing alkyl peroxide was designed for high stability during preparation and storage. Nuclear magnetic resonance spectroscopy (NMR), Raman, and triple-detection size-exclusion chromatography (TD-SEC) measurements were used to reveal the polymerization procedure and provide evidence of branching structure. In the case of polymerization at St₁₀₀-BPEMA_1.0-FeSO_{4 0.5}-SFS_0.2, the molecular weight increased and decreased with conversion below and above 75% monomer conversion, respectively. The decreasing of molecular weight with monomer conversion came from the increased viscosity of the micelle, which makes it difficult for the formed macromolecules containing vinyl group to participate into polymerization. Finally, the molecular weight reached a value of M_{n. SEC} = 439,200 g/mol at 92.2% conversion. In addition, the Zimm branching factor, g', also decreased and increased with conversion below and above 60% conversion, respectively, and then the g' finally attends a value of 0.41, showing high degree of branching. Branched poly(methyl methacrylate) was also prepared through this strategy, showing a versatile approach to branched vinyl polymers.     

Living cationic polymerization of α‐methyl vinyl ethers using SnCl4

Cationic polymerization of α‐methyl vinyl ethers was examined using an IBEA‐Et_1.5AlCl_1.5/SnCl₄ initiating system in toluene in the presence of ethyl acetate at 0 ～ ?78 °C. 2‐Ethylhexyl 2‐propenyl ether (EHPE) had a higher reactivity, compared to corresponding vinyl ethers. But the resulting polymers had low molecular weights at 0 or ?50 °C. In contrast, the polymerization of EHPE at ?78 °C almost quantitatively proceeded, and the number‐average molecular weight (M_n) of the obtained polymers increased in direct proportion to the EHPE conversion with quite narrow molecular weight distributions (weight‐average molecular weight/number‐average molecular weight ≤ 1.05). In monomer‐addition experiments, the M_n of the polymers shifted higher with low polydispersity as the polymerization proceeded, indicative of living polymerization. In the polymerization of methyl 2‐propenyl ether (MPE), the living‐like propagation also occurred under the reaction conditions similar to those for EHPE, but the elimination of the pendant methoxy groups was observed. The introduction of a more stable terminal group, quenched with sodium diethyl malonate, suppressed this decomposition, and the living polymerization proceeded. The glass transition temperature of the obtained poly(MPE) was 34 °C, which is much higher than that of the corresponding poly(vinyl ether). This poly(MPE) had solubility characteristics that differed from those of poly(vinyl ethers). © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 2202–2211, 2008     

Synthesis and properties of the polythiourethanes obtained by the cationic ring‐opening polymerization of cyclic thiourethanes

The cationic ring‐opening polymerization of a five‐membered thiourethane [3‐benzyl‐1,3‐oxazolidine‐2‐thione (BOT)] with boron trifluoride etherate afforded the corresponding polythiourethane with a narrow molecular weight distribution in an excellent yield. The molecular weight of the polymers could be controlled by the feed ratio of the monomer to the initiator. A kinetic study of the polymerization revealed that the polymerization rate of BOT (1.3 × 10^?2 L mol^?1 min^?1) was two times larger than that of the six‐membered thiourethane [3‐benzyltetrahydro‐1,3‐oxazolidine‐2‐thione (BTOT); 6.8 × 10^?3 L mol^?1 min^?1], and the monomer conversion obeyed the first‐order kinetic equation. These observations, along with the successful results in the two‐stage polymerization, supported the idea that this polymerization proceeded in a controlled manner. Block copolymerizations of BOT with BTOT were also carried out to afford the corresponding di‐ and triblock copolymers with narrow molecular weight distributions. The order of the 5% weight loss temperatures was as follows: poly(3‐benzyltetrahydro‐1,3‐oxazolidine‐2‐thione) [poly(BTOT)] > poly(BTOT₅₄‐b‐BOT₄₆) > poly(3‐benzyl‐1,3‐oxazolidine‐2‐thione) [poly(BOT)]. This indicated that an increase in the BTOT unit content raised the decomposition temperature. The order of the refractive indices was poly(BOT) > poly(BTOT₅₄‐b‐BOT₄₆) > poly(BTOT₅₄‐b‐BOT₄₆‐b‐BTOT₅₀) > poly(BTOT); this was in accord with the order of the sulfur content in the polymer chain. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 4795–4803, 2006     

In situ atom transfer radical polymerization of styrene with a tetraethylthiuram disulfide/copper bromide/2,2′‐bipyridine initiating system

The living radical polymerization of styrene in bulk was successfully performed with a tetraethylthiuram disulfide/copper bromide/2,2′‐bipyridine (bpy) initiating system. The initiator Et₂NCS₂Br and the catalyst cuprous bromide (CuBr) were produced from the reactants in the system through in situ atom transfer radical polymerization (ATRP). A plot of natural logarithm of the ratio of original monomer concentration to monomer concentration at present, ln([M]₀/[M]) versus time gave a straight line, indicating that the kinetics was first‐order. The number‐average molecular weight from gel permeation chromatography (GPC) of obtained polystyrenes did not agree well with the calculated number‐average molecular weight but did correspond to a 0.5 initiator efficiency. The polydispersity index (i.e., the weight‐average molecular weight divided by the number‐average molecular weight) of obtained polymers was as low as 1.30. The resulting polystyrene with α‐diethyldithiocarbamate and ω‐Br end groups could initiate methyl methacrylate polymerization in the presence of CuBr/bpy or cuprous chloride/bpy complex catalyst through a conventional ATRP process. The block polymer was characterized with GPC, ¹H NMR, and differential scanning calorimetry. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 4001–4008, 2001     

Cationic cyclopolymerization of new divinyl ethers: The effect of ether and ester neighboring functional groups on their cyclopolymerization tendency

The cationic polymerization of two new divinyl ethers, 1‐(2‐vinyloxyethoxy)‐2‐[(2‐vinyloxyethoxy)carbonyl]benzene ( 2 ) and 1,2‐bis[(2‐vinyloxyethoxy)carbonyl]benzene ( 3 ), as well as 1,2‐bis(2‐vinyloxyethoxy)benzene ( 1 ), with BF₃OEt₂ in CH₂Cl₂ at 0 °C at low initial monomer concentrations ([M]₀ = 0.15 and 0.075 M) gave soluble polymers with relatively high molecular weights and broad molecular weight distributions (MWDs), whereas reactions with the HCl/ZnCl₂ initiating system yielded soluble polymers with relatively narrow MWDs (weight‐average molecular weight/number‐average molecular weight ? 1.6) under similar reaction conditions. An NMR structural analysis of the HCl/ZnCl₂‐mediated polymers from the divinyl ethers showed that poly( 1 ) had virtually no unreacted vinyl ether groups throughout the polymerization (monomer conversion = 28–98%), whereas poly( 2 ) and poly( 3 ) possessed some amount of unreacted vinyl ether groups in the initial stage of the polymerization; the content of the vinyl groups of poly( 2 ) was 18 mol % at a 15% monomer conversion, and the content of the vinyl groups of poly( 3 ) was 31 mol % at an 18% monomer conversion. Therefore, divinyl ether 1 underwent cyclopolymerization exclusively to give almost completely cyclized polymers [degree of cyclization (DC) ～ 100%], whereas divinyl ethers 2 and 3 exhibited a lower cyclopolymerization tendency [DC for poly( 2 ) = 82%; DC for poly( 3 ) = 69%]. The differences in the cyclopolymerization tendencies among the divinyl ethers can be explained by the differences in the solvation powers of the neighboring functional groups adjacent to the vinyl ether moiety with the active center: the ether oxygen of the ether neighboring group solvates intramolecularly with the active center to accelerate the intramolecular propagation, but such an interaction is less effective with the more electron‐deficient oxygen attached to the carbonyl group of the ester neighboring group. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 281–292, 2003     

A novel group transfer polymerization of 1-trimethylsiloxy-benzocyclobutene via hetero Diels-Alder reaction

A novel group transfer polymerization via hetero-Diels-Alder reaction is described. When 1-trimethylsiloxybenzocyclobutene ( 1 ) was treated with a catalytic amount of p-anisaldehyde (4-methoxybenzaldehyde) and TASF (tris(dimethylamino)sulfonium difluorotrimethylsilanide) at room temperature for 0.5 h, poly[1,2-phenylene-1-(trimethylsiloxy)ethylene] was obtained quantitatively. The number-average molecular weight of the polymer was M̄_n = 2000 and the molecular weight distribution was narrow (ratio of weight-to number-average molecular weights M̄_w/M̄_n = 1.18). Structural characteristics suggested a polymerization mechanism involving isomerization of 1 to o-quinodimethane and successive hetero-Diels-Alder reaction leading to poly[1,2-phenylene-1-trimethylsiloxy ethylene]. The living-like nature of the polymerization was supported by a monomer addition experiment in which the molecular weight increased according to the increase of the added monomer.     

Vinyl polymerization. 403. Polymerization of vinyl monomer initiated with sodium poly-p-vinylphenolate

The polymerization of vinyl monomer initiated by poly-p-vinylphenol (PVPh) in NaOH aqueous solution was carried out at 85°C with shaking. Methyl methacrylate (MMA) was polymerized, whereas styrene and acrylonitrile were not. PVPh, which is dissociated into phenolate form (PVPh^?Na⁺) in NaOH aqueous solution, was effective for the polymerization. The effects of the amounts of MMA, PVPh, NaOH, and H₂O on the conversion of MMA were studied. The rate of polymerization of MMA increased with an increase in the molecular weight of PVPh-Na. The overall activation energy was estimated as 54 kJ mol^?1. The polymerization proceeded through a radical mechanism. The addition of tetra-n-butylammonium bromide increased the rate of polymerization.     

Controlled radical polymerization of 2‐hydroxyethyl methacrylate initiated by photofunctional 2‐(N,N‐diethyldithiocarbamyl)isobutyric acid

We demonstrated that density functional theory calculations provide a reliable and quantitative prediction of the trends in C? S bond dissociation energies using several model compounds as photoinitiator. On the basis of this information, we designed a possible photofunctional initiator for the polymerization of hydrophilic vinyl monomers. Photopolymerization of 2‐hydroxyethyl methacrylate (HEMA) hydrophilic monomer was carried out in ethanol initiated by 2‐(N,N‐diethyldithiocarbamyl)isobutyric acid (DTCA) under UV irradiation. We performed the first‐order time‐conversion plots in this polymerization system, and the straight line in the semilogarithmic coordinates indicated first order in monomer. The molecular weight of the poly(2‐hydroxyethyl methacrylate) (PHEMA) increased with increasing conversion. The molecular weight distribution (M_w/M_n) of the PHEMA was about 1.5. Methyl methacrylate (MMA) could also be polymerized in a living fashion with such a PHEMA precursor as a macroinitiator because PHEMA exhibited a dithiocarbamate (DC) group at its terminal end. This system could be applied to the architecture of amphiphilic block copolymers. It was concluded that these polymerization systems proceeded with controlled radical mechanism. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 76–82, 2004     

Synthesis of poly(β‐pinene)‐g‐poly(meth)acrylate by the combination of living cationic polymerization and atom transfer radical polymerization

New graft copolymers of β‐pinene with methyl methacrylate (MMA) or butyl acrylate (BA) were synthesized by the combination of living cationic polymerization and atom transfer radical polymerization (ATRP). β‐Pinene polymers with predetermined molecular weights and narrow molecular weight distributions (MWDs) were prepared by living cationic polymerization with the 1‐phenylethyl chloride/TiCl₄/Ti(OiPr)₄/nBu₄NCl initiating system, and the resultant polymers were brominated quantitatively by N‐bromosuccinamide in the presence of azobisisobutyronitrile, yielding poly(β‐pinene) macroinitiators with different bromine contents (Br/β‐pinene unit molar ratio = 1.0 and 0.5 for macroinitiators a and b , respectively). The macroinitiators, in conjunction with CuBr and 2,2′‐bipyridine, were used to initiate ATRP of BA or MMA. With macroinitiator a or b , the bulk polymerization of BA induced a linear first‐order kinetic plot and gave graft copolymers with controlled molecular weights and MWDs; this indicated the living nature of these polymerizations. The bulk polymerization of MMA initiated with macroinitiator a was completed instantaneously and induced insoluble gel products. However, the controlled polymerization of MMA was achieved with macroinitiator b in toluene and resulted in the desired graft copolymers with controlled molecular weights and MWDs. The structures of the obtained graft copolymers of β‐pinene with (methyl)methacrylate were confirmed by ¹H NMR spectra. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 1237–1242, 2003     

“LIVING-LIKE” CATIONIC POLYMERIZATION OF ISOBUTYL VINYL ETHER INITIATED BY CARBOXYL GROUPS ON CARBON BLACK SURFACE/ETHYLALUMINUM DICHLORIDE SYSTEM IN THE PRESENCE OF 1,4-DIOXANE

The effect of 1,4-dioxane as an added base on the cationic polymerization of isobutyl vinyl ether (IBVE) initiated by carboxyl groups on carbon black surface/ethylaluminum dichloride (EtAlCl₂) system was investigated. Although the cationic polymerization of IBVE by carbon black/EtAlCl₂ system the absence of 1,4-dioxane instaneously proceeded and the monomer conversion achieved 100% within a minute. The molecular weight distribution (MWD) of polyIBVE obtained was very broad. On the contrary, the MWD of polyIBVE obtained was very narrow and narrower than that obtained from the carbon black/ZnCl₂ initiating system by the addition of 1,4-dioxane. The number-average molecular weight (Mn) of polyIBVE obtained was directly proportional to monomer conversion in the cationic polymerization. However, the Mn of polyIBVE obtained from the polymerization by the initiating system in the the presence of 1,4-dioxane was smaller than that of the calculated value, assuming that polyl(IBVE) chain forms per unit carboxyl group on carbon black surface. It was concluded that carbon black/EtAlCl₂ initiating systems in the presence of 1,4-dioxane has an ability to initiate “living-like” cationic polymerization of IBVE based on the above results. PolyIBVE was grafted onto a carbon black surface after quenching the above “living-like” cationic polymerization systems with methanol.     

Facile one‐pot/one‐step technique for preparation of side‐chain functionalized polymers: Combination of SET‐RAFT polymerization of azide vinyl monomer and click chemistry

An azido‐containing functional monomer, 11‐azido‐undecanoyl methacrylate, was successfully polymerized via ambient temperature single electron transfer initiation and propagation through the reversible addition–fragmentation chain transfer (SET‐RAFT) method. The polymerization behavior possessed the characteristics of “living”/controlled radical polymerization. The kinetic plot was first order, and the molecular weight of the polymer increased linearly with the monomer conversion while keeping the relatively narrow molecular weight distribution (M_w/M_n ≤ 1.22). The complete retention of azido group of the resulting polymer was confirmed by ¹H NMR and FTIR analysis. Retention of chain functionality was confirmed by chain extension with methyl methacrylate to yield a diblock copolymer. Furthermore, the side‐chain functionalized polymer could be prepared by one‐pot/one‐step technique, which is combination of SET‐RAFT and “click chemistry” methods. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

A novel azo‐containing dithiocarbamate used for living radical polymerization of methyl acrylate and styrene

A novel azo‐containing dithiocarbamate, 1‐phenylethyl N,N‐(4‐phenylazo) phenylphenyldithiocarbamate (PPADC), was successfully synthesized and used to mediate the polymerization of methyl acrylate (MA) and styrene (St). In the presence of PPADC, the reversible addition‐fragmentation chain transfer (RAFT) polymerization was well controlled in the case of MA, however, the slightly ill‐controlled in the case of St. Interestingly, the polymerization of St could be well‐controlled when using PPADC as the initiator in the presence of CuBr/PMDETA via atom transfer radical polymerization (ATRP) technique. In the cases of RAFT polymerization of MA and ATRP of St, the kinetic plots were both of first‐order, and the molecular weight of the polymer increased linearly with the monomer conversion while keeping the relatively narrow molecular weight distribution (M_w/M_n). The molecular weight of the polymer measured by gel permeation chromatographer (GPC) was also close to the theoretical value (M_n(th)). The obtained polymer was characterized by ¹H‐NMR analysis, ultraviolet absorption, FTIR spectra analysis and chain‐extension experiments. Furthermore, the photoresponsive behaviors of azobenzene‐terminated poly(methyl acrylate) (PMA) and polystyrene (PS) were similar to PPADC. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 5626–5637, 2008     

Synthesis of poly(methyl methacrylate)-<Emphasis Type="Italic">block</Emphasis>-poly(tetrahydrofuran) by photo-living radical polymerization using a 2,2,6,6-tetramethylpiperidine-1-oxyl macromediator

The synthesis of a poly(methyl methacrylate)-block-poly(tetrahydrofuran) (PMMA-b-PTHF) diblock copolymer was attained by the photo-living radical polymerization of methyl methacrylate using 2,2,6,6-tetramethylpiperidine-1-oxyl (TEMPO) supported on the chain end of poly(tetrahydrofuran) (PTHF) as the macromediator. The polymerization was performed at room temperature by 2,2′-azobis(4-methoxy-2,4-dimethylvaleronitrile) as an initiator in the presence of bis(alkylphenyl)iodonium hexafluorophosphate as a photo-acid generator to produce the diblock copolymer consisting of poly(methyl methacrylate) (PMMA) and PTHF blocks connected through the TEMPO. The polymerization was confirmed to proceed in accordance with a living mechanism based on linear correlations for three different plots of the first order time-conversion, the molecular weight of the copolymer versus the monomer conversion, and the molecular weight versus the reciprocal of the initial concentration of the initiator. The molecular weight distribution of the block copolymer was dependent on the molecular weight of the macromediator based on the miscibility of PMMA and PTHF.     

Lipase‐Catalyzed Ring‐Opening Polymerization of 3(S)‐sec‐Butylmorpholine‐2,5‐dione

Lipase‐catalyzed ring‐opening bulk polymerizations of 3(S)‐sec‐butylmorpholine‐2,5‐dione (BMD) were investigated. Selected commercial lipases were screened as catalysts for BMD polymerization at 110°C. Polymerizations catalyzed with 10 wt.‐% of lipase PPL and PC result in BMD conversions of about 70% and in molecular weights of the products ranging from 5 500 to 10 700. Lipases MJ, CR and ES showed lower catalytic activities for the polymerization of BMD. Poly(3‐sec‐butylmorpholine‐2,5‐dione) has a carboxylic acid group at one end and a hydroxy group at the other end. During the polymerization racemization of the isoleucine residue takes place. Lipase PPL was selected for a more detailed study. The apparent rate of polymerization increases with increasing PPL concentration when the polymerization temperature is 110°C. When the PPL concentration is 5 and 10 wt.‐% with respect to the monomer, a conversion of about 70% is reached after 5 d and 3 d, respectively, while for a PPL concentration of 1 wt.‐% the conversion is less than 7% even after 6  d. High concentrations of PPL (10 wt.‐%) result in high M_n values (< 4  d). The highest molecular weight poly(BMD), M_n = 19 900, resulted from a polymerization conducted at 120°C with 5 wt.‐% PPL for 6 d. The general trend observed by varying the polymerization temperature is as follows: (i) monomer conversion and M_n increase with increasing reaction temperature from 110 to 125°C, (ii) monomer conversion and M_n decrease with an increase in reaction temperature from 125 to 130°C. Water content was found to be an important factor that controls both the conversion and the molecular weight. With increasing water content, enhanced polymerization rates are achieved while the molecular weight of poly(BMD) decreases.