粘土孔结构及添加铈对于催化剂上苯吸附-脱附-催化氧化性能的影响

采用3种不同孔结构的粘土材料,即Na型-蒙脱土(Na-mmt)、Al柱撑粘土(Al-PILC)和AlCe复合柱撑粘土(AlCe-PILC),以上述材料为载体,负载Mn和MnCe作为易挥发有机物(VOC)苯的氧化催化剂。利用N2吸附、程序升温还原(TPR)和程序升温表面反应(TPSR)等手段对催化剂的织构-结构、氧化-还原和吸附-脱附等性能进行了表征和分析。结果表明对于具有高比表面积和大孔径的改性粘土材料,添加适量的Ce有利于催化剂对低浓度苯的吸附,吸附量显著增加、脱附温度提高,上述条件都有利于对低浓度苯的深度氧化。同时,这一研究结果对改善"吸附-催化"一体化的低温吸附、高温脱附及氧化性能有极其重要的意义。     

Characterization of new catalysts based on uranium oxides

Catalysts based on uranium oxides were systematically studied for the first time. Catalysts containing various amounts of uranium oxides (5 and 15%) supported on alumina and mixed Ni-U/Al₂O₃ catalysts were synthesized. The uranium oxide catalysts were characterized using the thermal desorption of argon, the low-temperature adsorption of nitrogen, X-ray diffraction analysis, and temperature-programmed reduction with hydrogen and CO. The effects of composition, preparation conditions, and thermal treatment on physicochemical properties and catalytic activity in the reactions of methane and butane oxidation, the steam and carbon dioxide reforming of methane, and the partial oxidation of methane were studied. It was found that a catalyst containing 5% U on alumina calcined at 1000°C was most active in the reaction of high-temperature methane oxidation. For the Ni-U/Al₂O₃ catalysts containing various uranium amounts (from 0 to 30%), the introduction of uranium as a catalyst constituent considerably increased the catalytic activity in methane steam reforming and partial oxidation.     

Determination of Aromatic Arsines in Environmental Solids by Direct Thermal Desorption Gas Chromatography

To quantify aromatic arsines in the environment, such as World War I era chemical warfare agents and degradation products of arsenicals used in agriculture, a sensitive, selective, and direct method is needed. We describe the development and optimization of a method for the measurement of trace levels of triphenylarsine used as a model aromatic arsenic compound. Triphenylarsine was determined at low µg/g levels in sand, soil, and lake sediment by thermal desorption before gas–liquid chromatography (GC) with mass spectrometric and pulsed flame photometric detection. The dithiol derivative of phenylarsonic acid was used as an internal standard, thereby significantly improving the precision of the method. The desorption conditions were studied and found to be optimal at 350°C for 15?min. Significant improvement in precision was realized by preparing the solid samples as slurries in acetone and by inserting a small (～100?mg) quartz wool plug into the sample vial. The method was applied to determine triphenylarsine in authentic soil and sediment samples that had been fortified with triphenylarsine and aged for at least 15 days. Recoveries for soil samples ranged from 84.3?±?2.3 to 87.7?±?1.3%, while lower recoveries were obtained for sediment samples (75.1?±?3.0%). The detection limit for triphenylarsine in soil was 3.14?ng with a precision of 7.10% (n?=?4). Using these optimized conditions, the performance of the direct thermal desorption GC method for sample introduction was greatly improved compared to methods that have been reported in the literature.     

Low-temperature CO oxidation over CuO-CeO_2/SiO_2 catalysts:Effect of CeO_2 content and carrier porosity

The effects of CeO2 contents and silica carrier porosity with their pore diameters ranging from 5.2 nm to 12.5 nm of CuO-CeO2/SiO2 cata-lysts in CO oxidation were investigated.The catalysts were characterized by N2 adsorption/desorption at low temperature,X-ray diffraction (XRD),temperature-programmed reduction by H2 (H2-TPR),oxygen temperature programmed desorption (O2-TPD) and X-ray photoelectron spectroscopy (XPS).The results suggested that,the ceria content and the porosity of SiO2 carrier possessed great impacts on the structures and catalytic performances of CuO-CeO2/SiO2 catalysts.When appropriate content of CeO2 (Ce content 8 wt%) was added,the catalytic activity was greatly enhanced.In the catalyst supported on silica carrier with larger pore diameter,higher dispersion of CuO was observed,better agglomeration-resistant capacity was displayed and more lattice oxygen could be found,thus the CuO-CeO2 supported on Si-1 showed higher catalytic activity for low-temperature CO oxidation.     

Method for rapid tritiated water extraction from environmental samples

We have developed a thermal vacuum desorption process to rapidly extract water from environmental samples for tritium analysis. Thermal vacuum desorption allows for extraction of the moisture from the sample within a few hours in a form and quantity suitable for liquid scintillation counting and allows detection of tritium at the levels of <2 Bq/l of milk, <0.5 Bq/g of vegetation, and <0.5 Bq/g of soil. We developed a prototype unit that can process batches of twenty or more samples within 24 hours. Early data shows that a high percentage of water is extracted reproducibly without enrichment or depletion of the tritium content. The quench coefficient of the extracted water is low allowing for accurate, direct liquid scintillation counting. In most samples, good comparison has been observed with results using freeze-dry lyophilization as the water extraction method     

Removal of volatile organic compounds from activated carbon by thermal desorption and catalytic combustion

The thermal desorption of saturated activated carbon discharged from an industrial adsorber and catalytic oxidation of desorbed products over a Pt/Al₂O₃ catalyst were investigated. The activated carbon is almost completely regenerated by flushing with air at 200°C for 30 min. Desorbed products are fully oxidized over the Pt/Al₂O₃ catalyst above 275°C. The text was submitted by the authors in English.     

含钯类水滑石衍生复合氧化物Pd/M3AlO(M=Mg,Co, Ni,Cu, Zn)催化剂上氯苯的催化氧化

采用共沉淀法制备了系列含Pd类水滑石材料, 类水滑石基体为M3Al-HT (M=Mg, Co, Ni, Cu, Zn), 经焙烧制备出含Pd类水滑石衍生复合氧化物催化剂. 通过X射线衍射(XRD), 热重-差热分析(TG-DTG), H2程序升温还原(H2-TPR), O2程序升温脱附(O2-TPD)和N2吸脱附等表征技术手段研究了不同二价金属元素对含Pd类水滑石衍生复合氧化物催化剂物理化学性质及其对挥发性有机污染物氯苯催化氧化性能的影响. XRD和TG-DTG结果表明, 不同二价金属元素, 除Cu外, 都能形成类水滑石层状结构, Pd在不同类水滑石前驱物中均能良好分散. 不同的二价金属元素对催化剂性能的影响不同, 其中Pd/Co3AlO催化剂表现出最高的氯苯催化氧化活性, 其起燃温度和全转化温度分别为182和283 ℃. H2-TPR和O2-TPD测试表明, Pd和类水滑石衍生复合氧化物存在着协同作用, Pd的引入促进了复合氧化物的还原, 从而影响氧化物的氧化还原性能. Pd/M3AlO系列催化剂的活性主要受催化剂的氧化还原性能及其表面活性氧物种的影响.     

Low-temperature CO oxidation over CuO-CeO2/SiO2 catalysts：Effect of CeO2 content and carrier porosity

The effects of CeO2 contents and silica carder porosity with their pore diameters ranging from 5.2 nm to 12.5 nm of CuO-CeO2/SiO2 catalysts in CO oxidation were investigated. The catalysts were characterized by N2 adsorption/desorption at low temperature, X-ray diffraction (XRD), temperature-programmed reduction by H2 (H2-TPR), oxygen temperature programmed desorption (O2-TPD) and X-ray photoelectron spectroscopy (XPS). The results suggested that, the ceria content and the porosity of SiO2 carder possessed great impacts on the structures and catalytic performances of CuO-CeO2/SiO2 catalysts. When appropriate content of CeO2(Ce content ≤8 wt%) was added, the catalytic activity was greatly enhanced. In the catalyst supported on silica carrier with larger pore diameter, higher dispersion of CuO was observed, better agglomeration-resistant capacity was displayed and more lattice oxygen could be found, thus the CuO-CeO2 supported on Si-1 showed higher catalytic activity for low-temperature CO oxidation.     

A quantum chemical study of the decomposition of Keggin-structured heteropolyacids

Heterpolyacids (HPAs) demonstrate catalytic activity for oxidative and acid-catalyzed hydrocarbon conversion processes. Deactivation and thermal instability, however, have prevented their widespread use. Herein, ab initio density functional theory is used to study the thermal decomposition of the Keggin molecular HPA structure through the desorption of constitutional water molecules. The overall reaction energy and activation barrier are computed for the overall reaction HnXM12O40-->Hn-2XM12O39+H2O. and subsequently used to predict the effect of HPA composition on thermal stability. For example, the desorption of a constitutional water molecule is found to be increasingly endothermic in the order silicomolybdic acid (H4SiMo12O40)相似文献   

Kinetics of Copper Dissolution in the Solution of Polyacrylic Acid and Hydrogen Peroxide

Dependence of the rate of copper dissolution on the concentration of polyacrylic acid and hydrogen peroxide in aqueous solution was studied. The process rate was shown to grow with an increase in acid concentration in solution to 5.5 g/l; at concentrations above 10 g/l, the rate remains virtually constant. Within the concentration range from 6 to 30 mmol/l, hydrogen peroxide does not practically influence the rate of process. It was found that the rates of copper oxidation and copper(II) polyacrylate formation are significantly lower than those of the desorption of polyacrylic acid or its salts from the copper plate and are determined by the mass of polyacrylic acid adsorbed on the copper unit surface.     

WO2.90在烯烃催化氧化反应中的应用

本文研究大表面积的WO_2.90^[1]对丙烯的热脱附作用,并以丙烯和环己烯作为直链和环状烯烃的典型化合物,初步探讨其催化氧化性质。     

La~2~-~xSr~xNiO~4~-~λ系列催化剂结构与氨氧化活性的关系

本文报道了La~2~-~xSr~xNiO~4~-~λ(0≤x≤1)系列复合氧化物的固体结构性质和用于氨的氧化制硝酸的催化性能。La~2~-~xSr~xNiO~4~-~λ的晶胞体积V随x的增大而逐渐减小;c轴在x≤0.5前逐渐增大,在x≥0.5后逐渐减小。α轴在x≤0.5前逐渐减小,在x≥0.5后基本保持恒定。在x≤0.5前,La~2~-~xSr~xNiO~4~-~λ中存在氧过剩,在x≥0.5后存在氧缺陷。TPD表明,α氧(吸附在氧缺陷上的氧)在x=0.6时出现极大,β氧(晶格氧)随x增大而逐渐增大。La~2~-~xSr~xNiO~4~-~λ的氧化还原能力,Ni^3^+的量,氨氧化的NO选择性都随x增大而增加。由此得出,Ni^3^+是催化剂的活性离子,β氧是氨的氧化的活性氧种,在La~2~-~xSr~xNiO~4~-~λ上的氨的氧化遵循氧化还原(Redox)机理。     

Rapid screening of precursor and degradation products of chemical warfare agents in soil by solid-phase microextraction ion mobility spectrometry (SPME-IMS)

The use of solid-phase microextraction (SPME) coupled to ion mobility spectrometry (IMS) to detect precursor and degradation products of chemical warfare agents (CWAs) as soil contaminants was investigated. The development and characterization of a system to interface a thermal desorption solid-phase microextraction inlet with a hand held ion mobility spectrometer was demonstrated. The analytes used in this study were diisopropyl methylphosphonate (DIMP), diethyl methylphosphonate (DEMP), and dimethyl methylphosphonate (DMMP). Two SPME fibers with different stationary phases, 100 μm polydimethylsiloxane (PDMS) and 65 μm polydimethylsiloxane divinylbenzene (PDMS/DVB), were evaluated in this study to determine the optimal fiber and extraction conditions. Better results were obtained with the PDMS fiber. SPME-IMS offered good repeatability and detection of the precursor and degradation products in spiked soil at concentrations as low as 10 μg/g. Sample analysis time was less than 30 min for all the precursor and degradation products.     

选择性刻蚀制备铜锰复合氧化物及其CO催化氧化性能

由于在工业、环保和能源等诸多领域的潜在应用,低温CO催化氧化催化剂的研发引起了广泛关注.尽管贵金属表现出优越的CO氧化活性和稳定性,但是其有限储量和高昂价格一直限制着它们的实际应用.铜锰氧化物是著名的霍加拉特催化剂的主组分,价格低廉,催化氧化CO活性高,可高效替代贵金属催化剂.大量研究已证实, CO在铜锰氧化物上的氧化遵循氧化-还原机理,因此调变铜锰氧化物催化剂的氧化-还原性能对于改善其CO氧化活性至关重要.本文报道了一种简单的选择性刻蚀技术,即在铜、锰前驱物共沉淀过程中引入氨水作为刻蚀剂,利用氨水与铜离子的强络合作用选择性刻蚀铜组分,调变铜锰氧化物的铜锰比,有效改善了铜锰氧化物的氧化-还原特性,从而提高了其CO氧化性能. X射线粉末衍射(XRD)测试结果表明,初始制备的样品结晶弱,主要物相包含铜锰复合氧化物和氧化锰,此外还存在少量碳酸锰.不同浓度氨水刻蚀几乎未改变铜锰氧化物的物相组成.透射电子显微(TEM)照片中几乎没有发现晶格相,进一步证实这些铜锰氧化物的弱结晶本质.扫描电子显微(SEM)照片显示初始制备的铜锰复合氧化物主要由1.5?m左右的球形颗粒堆积而成,氨水刻蚀后颗粒形状变得不规则,表面更加粗糙,样品比表面积也从刻蚀前的85 m2/g增加到139 m2/g.理论上,氨水与铜的络合作用更强,样品主体和表面组成分析结果显示,随着氨刻蚀量增加,铜含量逐步降低,这清晰证实了氨有效地选择性刻蚀了铜组分. 进一步运用X射线光电子能谱(XPS)、氢程序升温还原(H2-TPR)、CO程序升温还原(CO-TPR)和氧程序升温脱附(O2-TPD)等测试手段表征了铜锰氧化物的氧化和还原特性,特别是氨刻蚀后催化剂氧化-还原性能. XPS分析显示铜锰氧化物中铜和锰物种的氧化态分别为+2和+3,氨刻蚀并没有改变两物种的氧化态. H2-TPR和CO-TPR证实氨刻蚀有效促进了铜锰氧化物中晶格氧从锰到铜物种的迁移,氨刻蚀同时还增强了与铜和锰键合的晶格氧物种的反应活性. O2-TPD结果进一步表明,氨刻蚀显著改善了铜锰氧化物中与铜键合晶格氧的释放.综合来看,氨刻蚀可有效促进铜锰氧化物的晶格氧迁移、释放和反应等氧化-还原特性. CO氧化反应研究显示,氨刻蚀大幅度促进了铜锰氧化物的催化活性.当反应温度在30?C时,相比于初始制备的铜锰氧化物催化剂,氨水刻蚀的样品上CO转化率提高了30%,达到90%转化率时的温度降低了20?C.关联催化剂结构表征和CO氧化性能数据发现,以表面Cu量归一化的CO氧化反应速率与催化剂的氧化-还原性能正相关.这一结果清晰证实氨刻蚀能显著改善铜锰氧化物的氧化-还原特性,进而有效促进其CO氧化活性.     

A+B2表面催化反应相变及自振荡的蒙特卡罗模拟

用MonteCarlo法研究了脱附和E－R机理对不可逆催化氧化反应A＋1／2B2→AB的相交和自振荡的影响、结果表明，（1）催化剂表面A的脱附使ZGB模型中的一级相变点消失，但对二级相交点的影响很小；当有E－R机理参与时，二级相交点消失，且E－R过程的几率对一级相交点的影响较大；当A的脱附和E－R过程同时起作用时，上述反应不存在相交（2）在ZGB模型中的二级相变点附近，反应速率随时间的变化具有明显的振荡现象，在其它位置主要表现为噪音。引入A的脱附后在二级相交点附近明显的自振荡现象依然存在；当E-R过程起作用时，随着二级相交点的消失，明显的振荡现象亦随之消失．（3）A的脱附和E－R过程对上述反应相变的影响与A的表面扩散对相变的影响有着本质的区别，因为后者只能改变相变点的位置而不能改变相变点的存在状况．     

氧化铈对氧化锰表面氧脱附与恢复性能的影响

采用TPD-MS技术研究了Mn-Ce-O体系催化剂的表面氧脱附(供出)和恢复性能,并以甲醇氧化反应为探针考察了催化剂在不同气氛下的氧化活性。结果表明,氧化铈的存在并不影响氧化锰O₂-TPD特征峰的位置,但氧化锰表面的吸附氧数量明显增加,氧化锰表面吸附氧的恢复能力随氧化铈含量的增加而增大。催化剂对甲醇的氧化活性与其表面吸附氧数量有很好的对应关系。催化剂表面氧恢复能力越大,对甲醇的氧化活性受气相氧影响越小。     

Catalytic elimination of carbon monoxide in gas streams by thermal and ozone oxidations

Summary The catalytic activities of Pt-Pd, 0.25 wt.% Mn and 0.56 wt.% Mn coated on Al₂O₃ pellets during catalytic thermal oxidation and catalytic ozone oxidation were investigated. The results reveal that the activity of catalysts in catalytic ozone oxidation differed substantially from that in catalytic thermal oxidation.      

La2-xSrxNiO4上氧的TPD及其氧化活性

La_2-xSr_xNiO₄上O₂的TPD研究表明,氧的脱附性能与催化剂结构中Ni²⁺和Ni³⁺的性质及含量有关,晶格氧直接参与了CO的氧化与甲烷的氧化偶联。     

SO_2对Co_3O_4/Al_2O_3选择性催化氧化NO的影响

采用流动态原位IR ,TPD及XPS技术研究了NO及SO2 在Co3 O4 /Al2 O3 金属氧化物催化剂表面上的吸附及脱附行为 ,并与该催化剂上模拟烟道气中NO的选择性催化氧化活性相关联 ,考察了SO2 对该反应过程的影响及作用机理 .