Fabrication of a gas sensor using pentacene thin films as a detector

Highly sensitive gas sensors for both acidic and basic gases were fabricated based on conducting thin films of polyacene compounds. Gas sensors formed with pentacene thin films deposited on various kinds of substrates were found to exhibit high sensitivity in detecting subppm concentrations of NO₂ or Cl₂ by monitoring the conductivity of the thin film. Improvements in the conductance and duration period for detection were achieved by changing the shape of electrodes and substrate. The sensors with PEN thin films initially doped with iodine could detect ppm concentrations of ammonia gas, since iodine molecules were dedoped upon exposure to ammonia, causing the reduction of the conductivity.     

Methodology for the selection of suitable sensors for incorporation into a gas sensor array

An investigation into suitable mathematical techniques which can be used to select sensor components for a gas sensor array is reported. Data from a tin dioxide Taguchi semiconductor sensor array were obtained individually for various organic solvents and analysed using multivariate techniques, including principal component analysis, cluster analysis and star symbol plots. It was shown that the array data produced a series of characteristic response patterns for the analytes. It was also found that analytes of similar chemical nature had similar response patterns, indicating a correlation between sensor interaction and the chemical functional groups of the analyte. The multivariate techniques used proved to be very useful in enabling a suitable selection of the components of the array to be made by identifying which of the components or sensors were acting independently.     

A weak acid extraction method as a tool for the metal pollution assessment in surface sediments

A simple technique has been evaluated for the initial assessment of heavy metal pollution in coastal sediments, in order to overcome many difficulties involved in routine monitoring of such analytes.The leaching of sediment samples with a cold dilute HC1, which affects only the non-residual part of the metals, gives the anthropogenic fingerprints on the bottom deposits and provides more data on the extent of heavy metal pollution relatively to the total sediment analysis.The proposed technique has been applied in most Hellenic coastal regions, both polluted and unpolluted. Comparisons between the various regions with the use of an enrichment factor have been made, which establish the gross degree to which a sediment population has been subjected to heavy metal pollution from the overlying waters.     

Evaluation of doped and undoped poly (o‐anisidine) as sensing materials for a sensor array for volatile organic compounds

Poly (o‐anisidine) (PoANI) and PoANI doped with nickel oxide and zinc oxide were evaluated as sensing materials for four gas analytes (methanol, ethanol, acetone, and benzene). The sensing materials had high sensitivity (showing an affinity towards the target analytes even at low concentrations, in the range of 1‐5 ppm), but rather poor selectivity, especially when the gas analytes were in a mixture. To exploit the poor selectivity, the three sensing materials were combined into a sensor array using principal component analysis (PCA) as a sensing algorithm. It was found that using a sensor array, the four individual gases could be separated. However, when all four gases were present (in analyte mixtures), there was too much overlap in the responses to distinguish between individual gas analytes and their related mixtures.     

A fiber optic sensor with a metal organic framework as a sensing material for trace levels of water in industrial gases

Industrial gases such as nitrogen, oxygen, argon, and helium are easily contaminated with water during production, transfer and use, because there is a high volume fraction of water in the atmosphere (approximately 1.2% estimated with the average annual atmospheric temperature and relative humidity). Even trace water (<1 parts per million by volume (ppmv) of H₂O, dew point < −76 °C) in the industrial gases can cause quality problems in the process such as production of semiconductors. Therefore, it is important to monitor and to control trace water levels in industrial gases at each supplying step, and especially during their use. In the present study, a fiber optic gas sensor was investigated for monitoring trace water levels in industrial gases. The sensor consists of a film containing a metal organic framework (MOF). MOFs are made of metals coordinated to organic ligands, and have mesoscale pores that adsorb gas molecules. When the MOF, copper benzene-1,3,5-tricarboxylate (Cu-BTC), was used as a sensing material, we investigated the color of Cu-BTC with water adsorption changed both in depth and tone. Cu-BTC crystals appeared deep blue in dry gases, and then changed to light blue in wet gases. An optical gas sensor with the Cu-BTC film was developed using a light emitting diode as the light source and a photodiode as the light intensity detector. The sensor showed a reversible response to trace water, did not require heating to remove the adsorbed water molecules. The sample gas flow rate did not affect the sensitivity. The obtained limit of detection was 40 parts per billion by volume (ppbv). The response time for sample gas containing 2.5 ppmvH₂O was 23 s. The standard deviation obtained for daily analysis of 1.0 ppmvH₂O standard gas over 20 days was 9%. Furthermore, the type of industrial gas did not affect the sensitivity. These properties mean the sensor will be applicable to trace water detection in various industrial gases.     

Rare earth ions-enhanced gold nanoclusters as fluorescent sensor array for the detection and discrimination of phosphate anions

The discrimination and detection of phosphate anions have attracted extensive attention due to their important roles in various biological processes. Compared with sensors to detect one individual phosphate at a time, sensor arrays are able to discriminate multiple phosphates simultaneously. In this study, we developed a rare earth ions enhanced AuNCs-based sensor array to achieve facile and rapid identification of phosphate anions (PPi, ADP and ATP). The rare earth ions (i. e., Ce³⁺, Gd³⁺, Tm³⁺ and Yb³⁺) can significantly enhance the fluorescence of AuNCs through aggregation-induced emission effect. And the subsequent addition of phosphate anions can recover the fluorescence of the AuNCs-rare earth ions assembly. Thanks to the different numbers of phosphate group and different steric hindrance effects of phosphate anions, the recovery fluorescence of AuNCs-rare earth ions assembly induced by PPi, ADP or ATP are respectively distinct. Thus the sensor array composed of AuNCs and different rare earth ions is able to distinguish those phosphate anions. Finally, the sensor array was successfully demonstrated to identify the phosphates in blind samples.     

SPR imaging as a tool for detecting mucin – anti-mucin interaction. Outline of the development of a sensor for near-patient testing for mucin

Sensors able to provide ‘yes’/‘no’ answers have become of interest in recent years, especially in the fields of environmental research and healthcare. We describe a procedure based on surface plasmon resonance imaging (SPRI) to investigate the interaction between mucin and anti-mucin antibody, and we outline the development of an alarm sensor for the protein mucin, whose high concentration in saliva, blood or tissue is related to illnesses such as gingivitis, peridontitis or even cancer. Anti-mucin gastric antibodies are immobilised onto a gold surface. The immobilisation is evaluated for neat gold chips and for polymer-modified gold surfaces. We found that two different pHs are required, one for the immobilisation of the antibodies on gold (pH 5.5) and a different one for optimal interaction between the sample and the antibody layer (pH 7.0). Finally, we briefly demonstrate the application of the sensor to real saliva samples, both mucin-less and mucin-containing, evaluating the potential of the sensor to discriminate between healthy and ill.     

Performance and characteristics of a trace gas analyzer for the determination of volatile organic compounds in air

An instrument has been developed and tested for the continuous measurement of volatile organic compounds (VOC) in air. The system consists of a gas chromatograph equipped with a dedicated sampling device that allows the sample to be transferred to a cooled microtrap via sampling loops (10, 100, 250 ml) or via a direct pump transfer to the trap. The microtrap is placed in the chromatographic oven just below a modified split-splitless injector, allowing direct liquid injection for calibration of the system; the injector is in communication with the sampling valve equipped with the loop and the sampling pump. The system allows 24-hour sampling and analysis of a large number of VOC (up to 25 individual hydrocarbons ranging from C2 C9) and also polar volatile organic compounds PVOC. Thanks to the particular trap geometry, a minimum consumption of liquid nitrogen (between 150 300 ml) is needed for each analytical run and no water managing system is normally required for humid air samples.     

Air pollution measurement as a tool for practical policy and control strategy

Summary The problems of air pollution are discussed and possibilities for control and monitoring by analytical measurement are presented.

---

Messung der Luftverschmutzung als Mittel für praktische Kontrollmanahmen

Zusammenfassung Die Problematik der Luftverschmutzung wird diskutiert und Möglichkeiten zur Kontrolle und Überwachung besprochen.

Lecture presented at Euroanalysis I Conference, 28. 8.–1. 9. 1972 in Heidelberg, Germany.     

Borazine as a sensor for fluoride ion: a computational and experimental study

The computational and experimental studies have revealed that even simple molecule like borazine can act as a sensor for fluoride ions. This study further reported the various binding modes of analytes using quantum chemical calculations and the nature of such interactions have been examined using electron density surface analysis. Total charge transfer analysis (q_CT) correlates well with the binding affinities of analytes with the borazine receptor.     

Performance characteristics of a new prototype for a portable GC using ambient air as carrier gas for on-site analysis

The performance characteristics of a portable GC instrument requiring no compressed gas supplies and using relatively lightweight transportable components for the analysis of volatile organic components in large-volume air samples are described. To avoid the need for compressed gas tanks, ambient air is used as the carrier gas, and a vacuum pump is used to pull the carrier gas and injected samples through the wall-coated capillary column and a photoionization detector (PID). At-column heating is used eliminating the need for a conventional oven. The fused silica column is wrapped with heater wire and sensor wire so that heating is provided directly at the column. A PID is used since it requires no external gas supplies and has high sensitivity for many compounds of interest in environmental air monitoring. In order to achieve detection limits in the ppb range, an online multibed preconcentrator containing beds of graphitized carbons and carbon molecular sieves is used. After sample collection, the flow direction through the preconcentrator is reversed, and the sample is thermally desorbed directly into the column. Decomposition of sensitive compounds during desorption is greater with air as the carrier gas than with hydrogen.     

Optimization and modeling of Zn2SnO4 sensitivity as gas sensor for detection benzene in the air by using the response surface methodology

In this paper, the performance of the benzene gas detection sensor in the air is optimized by an experimental design method. So in this work, Nanostructured thin films of ZnO and Zn₂SnO₄ were prepared in wurtzite form via a facile atmospheric pressure chemical vapor deposition (CVD) method, using metallic zinc and tin precursors. Characterization of the gas sensor was performed by using Powder X-ray diffraction (PXRD), scanning electron microscopy (SEM) and surface area analysis (using BET method). The results show that Zn₂SnO₄ nanowire network exhibited good sensitivity at 299 °C temperature to low concentrations (100 ppb) of Benzene which can be potentially used as a resistive gas sensor. Ultimately modeling and optimization of Zn₂SnO₄ sensor performance to detect benzene by surface response method in design expert11 software has been done. Also, the effect of each parameter on the sensitivity of the sensor was analyzed by analysis of variance (ANOVA). Moreover, the performance efficiency of the Zn₂SnO₄ sensor is estimated with the reliable correlations obtained in the modeling. The two parameters selected to optimize the performance of the gas sensor include the operating temperature of the sensor and the concentration of the sensor. Comparison of the modeling results and the predicted values for the sensor sensitivity to benzene shows 97.60% excellent agreement.     

Thiourea-treated graphene aerogel as a highly selective gas sensor for sensing of trace level of ammonia

As a result of this study, a new and simple method was proposed for the fabrication of an ultra sensitive, robust and reversible ammonia gas sensor. The sensing mechanism was based upon the change in electrical resistance of a graphene aerogel as a result of sensor exposing to ammonia. Three-dimensional graphene hydrogel was first synthesized via hydrothermal method in the absence or presence of various amounts of thiourea. The obtained material was heated to obtain aerogel and then it was used as ammonia gas sensor. The materials obtained were characterized using different techniques such as Fourier transform infra red spectroscopy (FT-IR), thermal gravimetric analysis (TGA), X-ray diffraction (XRD) and scanning electron microscopy (SEM). The thiourea-treated graphene aerogel was more porous (389 m² g⁻¹) and thermally unstable and exhibited higher sensitivity, shorter response time and better selectivity toward ammonia gas, compared to the aerogel produced in the absence of thiourea. Thiourea amount, involved in the hydrogel synthesis step, was found to be highly effective factor in the sensing properties of finally obtained aerogel. The sensor response time to ammonia was short (100 s) and completely reversible (recovery time of about 500 s) in ambient temperature. The sensor response to ammonia was linear between 0.02 and 85 ppm and its detection limit was found to be 10 ppb (3S/N).     

HRGC of wine free amino acids as a tool for elementary wine characterization

In this paper we show that wine free amino acids derivatized as isopropyl N-heptafluorobutyryl esters can be used as a tool for wine characterization. Elementary wines of eight Vitis vinifera varieties were studied during a seven year period. The characteristic wine amino acids for each variety were assessed by means of pattern recognition techniques. A “star symbol plot” was used for graphic representation.     

Bovine serum albumin as a molecular sensor for the discrimination of complex metabolite samples

The potential for using serum albumin (SA) as a broadly applicable molecular sensor was explored in an effort to develop a method for rapid analysis of complex metabolite samples. SA is a protein present at high concentration in blood, which transports a diverse set of compounds including fatty acids, hormones, and drugs. The effectiveness of the bovine ortholog (BSA) as a molecular sensor was tested by analyzing the pool of small molecules bound to the protein after a brief incubation with complex fluids of biological origin. As an initial test, three varietals of red wine were readily distinguished. Further analysis using four varietals of white wine also showed clear separation. In a second analysis using urine, animals in hemorrhagic shock were separated from a group of comparably treated controls. A time course analysis showed that recovery from injury could also be followed using the assay. This finding is significant as there currently is no method or biomarker for predicting the onset of shock. Comparison of samples was based on liquid chromatography mass spectrometry (LCMS) analysis of compounds selectively bound by BSA. Analysis of the samples after protein selection revealed a significant reduction in complexity and clear separation of groups by Principle Component Analysis (PCA). These results show the potential for using cargo-carrying proteins as molecular sensors for screening complex samples without the need for prior knowledge of sample composition or concentration and may streamline elucidation of biomarkers.     

Evaluation of chemometric techniques for the identification and quantification of solvent mixtures using a thin-film metal oxide sensor array

An evaluation was made of suitable chemometric techniques that can be used in both the selection of suitable sensors for a sensor array and the subsequent identification and quantification of analytes using such a device. Data fro a thin-film tin oxide-based gas sensor were obtained for a range of analytes, both pure and in mixtures and analysed using several chemometric techniques, including principal component analysis, cluster analysis and partial least squares. It was shown that the array produced a characteristic response pattern for the analytes, and this was then used for the identification of ethyl acetate, acetone, ethanol and pentane, and the determination of ethanol in various mixtures. The chemometric techniques were not only used to identify and quantify components in the solvent mixture but also indicated which of the array elements were acting independently and the level of interaction which was occurring. The results obtained describe a chemometric and fabrication protocol for sensor array design.     

A lithium‐organic framework as a fluorescent sensor for detecting aluminum (III) ion

Due to the low coordination number and the relatively weak coordination ability, it is a great challenge to introduce Li⁺ into the construction of metal–organic frameworks (MOFs). Here, one Li‐based metal–organic framework (Li‐MOF), [Li₄L(DMF)₂]_n ( HNU‐31 ), is constructed by the assembly of LiNO₃ and 5‐(bis(4‐carboxybenzyl)amino)isophthalic acid (H₄L) ligand, which possesses a 3D framework, and can be serve as a luminescent sensor for detecting Al³⁺ ion with the detection limit of 4 × 10^?6 M.     

Thiourea functionalized CdSe/CdS quantum dots as a fluorescent sensor for mercury ion detection

CdSe/CdS quantum dots(QDs) functionalized by thiourea(TU) were synthesized and used as a fluorescent sensor for mercury ion detection.The TU-functionalized QDs were prepared by bonding TU via electrostatic interaction to the core/shell CdSe/CdS QDs after capping with thioglycolic acid(TGA).It was observed that the fluorescence of the functionalized QDs was quenched upon the addition of Hg~(2+).The quantitative detection of Hg~(2+) with this fluorescent sensor could be conducted based on the linear relationship between the extent of quenching and the concentration of Hg~(2+) added in the range of1-300 μg L~(-1).A detection limit of 0.56 μg L~(-1) was achieved.The sensor showed superior selectivity for Hg~(2+) and was successfully applied to the determination of mercury in environmental samples with satisfactory results.     

Mercury meniscus on solid silver amalgam electrode as a sensitive electrochemical sensor for tetrachlorvinphos

The in-house prepared mercury meniscus modified solid silver amalgam electrode (m-AgSAE) was successfully applied for the detection of organophosphate pesticide tetrachlorvinphos in pH 7 buffer solution. The electrochemical performance of m-AgSAE for the reduction of tetrachlorvinphos was evaluated using cyclic voltammetry (CV), differential pulse voltammetry (DPV), and square wave voltammetry (SWV), respectively. The surface morphology of solid silver electrode (AgE), as-amalgamated solid silver amalgam electrode (AgSAE), and polished solid silver amalgam electrode (p-AgSAE) was examined by field emission scanning electron microscopy (FESEM). Among the applied techniques, DPV and SWV analysis showed a remarkable increase in the reduction peak current and provided a simple, fast, and sensitive method for the determination of tetrachlorvinphos. The electrochemical impedance spectroscopy (EIS) was used to correlate the electrocatalytic activity of AgSAE, p-AgSAE and m-AgSAE with their interfacial charge transport capabilities. Under the optimized experimental conditions, the DPV and SWV responses were linear over the 1–9 μM and 10–50 μM concentration ranges with a detection limit of 0.06 μM for DPV and 0.04 for SWV. The estimation of tetrachlorvinphos in the ground and waste water samples with the proposed method was in good agreement with that of the added amount. The proposed electrochemical method not only extends the application of non-toxic m-AgSAE, but also offers new possibilities for fast and sensitive analysis of tetrachlorvinphos and its structural analogs in environmental samples.