水杨醛亚胺钒（III）化合物催化乙烯聚合反应机理

钒系烯烃聚合催化剂在工业上有着不可替代的位置,它可用于制备高活性窄分布的聚合物、乙烯与α-烯烃共聚物和间规聚丙烯等。但由于实验手段难以确定钒催化剂活性物种的结构,进一步对催化机理的确认及催化剂结构的改进十分困难。本文运用密度泛函方法对水杨醛亚胺钒配合物催化乙烯聚合的活性物种结构进行了理论研究。对多种活性物种模型的比较研究结果表明,对此催化反应最有利的活性物种为中性双金属物种a1, a1结构中包含两个连接铝原子与钒中心的氯桥结构。研究同时表明,助催化剂AlEt2Cl的存在不仅加速了钒配合物前体的烷基化反应,同时其对活性物种a1结构中氯桥的形成至关重要。最后还研究了该催化体系的链终止反应机理。     

Photoinitiation by radical-cationic mechanism in the polymerization of isobutylene with lewis acids

ESR spectra of Lewis acids (VCl₄, TiCl₄, TiBr₄, SnCl₄, and AlBr₃) and their mixtures with isobutylene were investigated in a n-heptane solution in the dark and under irradiation at 400–480 nm at ?80 to ?150°C. A signal was observed only upon irradiating mixtures of VCl₄, TiCl₄, or TiBr₄ and isobutylene. The signal was identified as an isobutylene radical-cation by comparison with a simulated spectrum. A signal indicating the presence of peroxy radicals were recorded in measurements carried out in the presence of oxygen; these radicals originated from reaction of the isobutylene radical-cation with oxygen. Radical-cation initiation by visible light is indicated by the polymerization of isobutylene by VCl₄, TiCl₄, and TiBr₄ and by ESR spectra. The inhibiting effect of oxygen in photochemically initiated polymerization of isobutylene was also elucidated.     

Emulsion polymerization of tetrafluoroethylene and isobutylene

Interpolymers of tetrafluoroethylene and isobutylene containing approximately equimolar amounts of each monomer have been prepared by emulsion polymerization. Also prepared were compositions containing small amounts of other monomers such as acrylic acid. The characterization of these products is discussed, as is the preparation of both “ionomer” and iminated derivatives of the carboxylated terpolymers.     

Radiation-induced polymerization of isobutylene oxide

In the absence of oxygen, liquid isobutylene oxide is polymerized by high energy radiation. The resultant polyethers may possess the same gross structures as those prepared by Lewis acid catalysis: The reaction is characterized by (1) a small, apparent activation energy (2.7 kcal/mole), (2) a polymerization rate proportional to the first power of the dose rate, (3) inhibition by Lewis bases, and (4) moderate inhibition by free-radical scavengers. The molecular weights of the polymers increase with decreasing temperatures of polymerizations. These results will be discussed in terms of a cationic propagation mechanism.     

Some aspects of the living isobutylene polymerization

The possibilities of increasing the livingness in cationic isobutylene polymerizations has been investigated. It has been assumed that the living chain-end is polarized but non-dissociated and relatively stable, therefore, i) shifting of the dissociation equilibrium by adding salts with common or non-common anion in excess, and ii) increasing of the stability of the chain-end by complexing it with electrondonors, may increase the livingness of the system. Indeed, the addition of n-Bu₄NCl or n-Bu₄NI to systems with BCl₃ or TiCl₄ coinitiators, as well as the addition of dimethyl sulphoxide as electrondonor in a broad concentration range, improved the living character. The possibility of complexation of the chain-end by the monomer has also been supported     

A visible light photocatalyst: effects of vanadium substitution on ETS-10

Hybrid density functional theory/molecular mechanics (DFT/MM) methods have been used to investigate the effects of vanadium substitution in ETS-10. Models have been developed to contain varying concentrations of V(IV) and V(V) within the O-M-O (M = Ti, V) chain. Most of the V-substituted models have a localized mid-gap state. The occupation of this localized state depends upon the dopant oxidation state, leading to the addition of multiple low energy transitions. A linear correlation has been identified between band gap energies estimated using ground state orbital energies and those calculated using the more accurate and computationally demanding time-dependent DFT (TDDFT) method for a variety of transition metal substituted models of ETS-10. Consistent with experimental data for V substitution, our models predict a decrease in the optical band gap with increasing [V], due to a lowering of the delocalized d-orbital states at the bottom of the conduction band with increasing V d-orbital character. This effect is more pronounced in the case of V(V) substitution than V(IV). Excitation energies for the V-doped models, calculated with TDDFT methods correlate well with experimental data, allowing for the assignment of specific optical transitions to experimental UV-Vis spectra. The electronic structure of V-substituted ETS-10 at high V concentration demonstrates band gap energies within the visible range of the spectrum. Additionally, at high [V] the band gap energy and presence of low energy electron traps can be controlled by the relative concentration of V(IV) and V(V) along the O-M-O chain, establishing V-substituted ETS-10 as a promising visible light photocatalyst.     

Living carbocationic polymerization. IV. Living polymerization of isobutylene

Truly living polymerization of isobutylene (IB) has been achieved for the first time by the use of new initiating systems comprising organic acetate-BCl₃ complexes under conventional laboratory conditions in various solvents from ?10 to ?50°C. The overall rates of polymerization are very high, which necessitated the development of the incremental monomer addition (IMA) technique to demonstrate living systems. The living nature of the polymerizations was demonstrated by linear M _n versus grams polyisobutylene (PIB) formed plots starting at the origin and horizontal number of polymer molecules formed versus amount of polymer formed plots. DP _n obeys [IB]/[CH₃COOR^t · BCl₃]. Molecular weight distributions (MWD) are very narrow in homogeneous systems (M _w/M _n = 1.2–1.3) whereas somewhat broader values are obtained when the polymer precipitates out of solution (M _w/M _n = 1.4–3.0). The MWDs tend to narrow with increasing molecular weights, i.e., with the accumulation of precipitated polymer in the reactor. Traces of moisture do not affect the outcome of living polymerizations. In the presence of monomer both first and second order chain transfer to monomer are avoided even at ?10°C. The diagnosis of first and second order chain transfer has been accomplished, and the first order process seems to dominate. Forced termination can be effected either by thermally decomposing the propagating complexes or by nucleophiles. In either case the end groups will be tertiary chlorides. The living polymerization of isobutylene initiated by ester. BCl₃ complexes most likely proceeds by a two-component group transfer polymerization.     

Living carbocationic polymerization. IV. Living polymerization of isobutylene

Truly living polymerization of isobutylene (IB) has been achieved for the first time by the use of new initiating systems comprising organic acetate-BCl³ complexes under conventional laboratory conditions in various solvents from −10 to −50°C. The overall rates of polymerization are very high, which necessitated the development of the incremental monomer addition (IMA) technique to demonstrate living systems. The living nature of the polymerizations was demonstrated by linear versus grams polyisobutylene (PIB) formed plots starting at the origin and horizontal number of polymer molecules formed versus amount of polymer formed plots. obeys [IB]/[CH₃COOR^t · BCl₃]. Molecular weight distributions (MWD) are very narrow in homogeneous systems whereas somewhat broader values are obtained when the polymer precipitates out of solution . The MWDs tend to narrow with increasing molecular weights, i.e., with the accumulation of precipitated polymer in the reactor. Traces of moisture do not affect the outcome of living polymerizations. In the presence of monomer both first and second order chain transfer to monomer are avoided even at −10°C. The diagnosis of first and second order chain transfer has been accomplished, and the first order process seems to dominate. Forced termination can be effected either by thermally decomposing the propagating complexes or by nucleophiles. In either case the end groups will be tertiary chlorides. The living polymerization of isobutylene initiated by ester · BCl₃ complexes most likely proceeds by a two-component group transfer polymerization.     

Cationic polymerization of isobutylene at room temperature

This review highlights recent approaches toward polyisobutylene (PIB) by an energy efficient room temperature cationic polymerization. Special focus is laid on our own work using modified Lewis acids and nitrile‐ligated metal complexes associated with weakly coordinating anions. In both cases, suitable conditions have been found for efficient production of PIB characterized by medium to low molar masses and a high content of exo double bonds as end groups—the typical features of highly reactive PIB, an important commercial intermediate toward oil and gasoline additives. These and other approaches demonstrate that the cationic polymerization of isobutylene is still not fully explored, and new innovative catalyst systems can lead to surprising results of high commercial interest. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

Spectrophotometric determination of vanadium with 1,10-phenanthroline

A simple and sensitive spectrophotometric method for the determination of vanadium based upon the reaction of vanadate with 1,10-phenanthroline in the presence of sodium dithionite in ammoniacal solution is described. The absorbance of the complex measured at 645 nm follows Beer's law for solutions containing 30-400 microg of vanadium in 100 ml of solution. A 10-fold excess of molybdenum, tungsten, phosphorus or chromium does not interfere. The molar absorptivity is 8.0 x 10(3) 1 mole(-1) cm(-1). The complex is shown to be tris-1,10-phenanthroline vanadium(II). The method has been applied successfully to the determination of vanadium in bauxite.     

Insight into the catalytic mechanism of vanadium haloperoxidases. DFT investigation of vanadium cofactor reactivity

Density functional theory (DFT) has been used to investigate the catalytic properties of the isolated vanadium cofactor found in vanadium haloperoxidases, with a particular emphasis on the steps going from the resting form of the cofactor to the peroxo complex. Computation of transition states, intermediate species, and UV-vis spectra, as well as comparison of reaction energies, demonstrated the important role of protonation in cofactor activation. This illustrates that the resting form of the vanadium cofactor reacts with hydrogen peroxide according to a mechanism that implies formation of an aqua complex, release of the apical water molecule according to a dissociative pathway, and binding of hydrogen peroxide to vanadium. This process leads to a side-on peroxo species corresponding to the peroxo form observed in the enzyme. In addition, it appears that an acid-base catalysts strongly accelerates the conversion to the side-on peroxo form. The comparison of computed and experimental UV-vis spectra corroborated the proposed reaction pathway and allowed us to explain the effects of the vanadium ligands on the electronic properties of the cofactor.     

Stereospecific polymerization of butadiene in the presence of isobutylene

The polymerization of isobutylene–butadiene monomer mixtures by a cobalt-containing catalytic system (cobaltous acetylacetonate–diethylaluminum chloride–water) yields a homopolymer mixture consisting of polyisobutylene and polybutadiene. It is assumed that the polymerization of both monomers proceeds according essentially identical reaction mechanisms, i.e., isobutylene polymerizes cationically and butadiene follows a coordination-cationic mechanism.     

New details concerning the reactions of nitric oxide with vanadium tetrachloride

The slow addition of NO to a CCl(4) solution of VCl(4) reproducibly forms the known polymer [V(NO)(3)Cl(2)](n)() as a dark brown powder. Treatment of a CH(2)Cl(2) suspension of [V(NO)(3)Cl(2)](n)() with excess THF generates mer-(THF)(3)V(NO)Cl(2) (1) which can be isolated as an orange crystalline material in 55% yield. The reaction of 1 with excess MeCN or 1 equiv of trimpsi (trimpsi = (t)BuSi(CH(2)PMe(2))(3)) provides yellow-orange (MeCN)(3)V(NO)Cl(2)xMeCN (2xMeCN) and yellow (trimpsi)V(NO)Cl(2) (3), respectively. A black, crystalline complex formulated as [NO][VCl(5)] (4) is formed by the slow addition of NO to neat VCl(4) or by the reaction of excess ClNO with neat VCl(4). Complex 4 is extremely air- and moisture-sensitive, and IR spectroscopy suggests that in solutions and in the gas phase it dissociates back into VCl(4) and ClNO. Reaction of 4 with excess [NEt(3)(CH(2)Ph)]Cl generates [NEt(3)(CH(2)Ph)](2)[VCl(6)]x2CH(2)Cl(2) (5x2CH(2)Cl(2)), which can be isolated as deep-red crystals in 51% yield. All new complexes have been characterized by conventional spectroscopic methods, and the solid-state molecular structures of 1, 2xMeCN, and 5x2CH(2)Cl(2) have been established by single-crystal X-ray diffraction analyses.     

A new visible light sensitive photoinitiator system for the cationic polymerization of epoxides

This communication reports the development of an efficient three‐component visible light sensitive photoinitiator system for the cationic ring‐opening photopolymerization of epoxide monomers and epoxide functional oligomers. The photoinitiator system consists of camphorquinone in combination with a benzyl alcohol to generate free radicals by the absorption of visible light. Subsequently, the radicals participate in the free radical chain induced decomposition of a diaryliodonium salt. The resulting strong Brønsted acid derived from this process catalyzes the cationic ring‐opening polymerization of a variety of epoxide substrates. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 866–875, 2009     

Spectrophotometric determination of vanadium with n-benzoyl-o-tolylhydroxylamine

N-Benzoyl-o-tolylhydroxylamine is shown to provide a virtually specific reagent for the spectrophotometric determination of vanadium. The reddish-violet complex formed with the reagent in 4–8 N hydrochloric acid after extraction with chloroform shows absorption maxima at 510 mm, and obeyes Beer's law from 0.5 to 10 μg with an optimum range of 2–10 μg; the percent relative error is 2.7. The sensitivity is 0.0108 μg V/cm². The complex contains the metal and the reagent in a ratio of 1:2 and the dissociation constant is of the order of 10^-9.