Solubility of carbon dioxide in aqueous solution of 2-amino-2-methyl-1-propanol and piperazine

In this work, new experimental results of the vapour-liquid equilibrium (VLE) of CO₂ in aqueous 2-amino-2-methyl-1-propanol (AMP) and piperazine (PZ) have been presented in the temperature range of 298-328 K and PZ concentration range of 2-8 mass%, keeping the total amine concentration in the solution at 30 mass%. The partial pressures of CO₂ were in the range of 0.1-1450 kPa. A thermodynamic model was developed to correlate and predict the VLE of CO₂ in aqueous AMP + PZ. The electrolyte nonrandom two liquid (ENRTL) theory has been used to develop the VLE model for the quaternary system (CO₂ + AMP + PZ + H₂O) to describe the equilibrium behaviour of the solution. The experimental data from this work and data available in the literature were used to regress the ENRTL interaction parameters. The model predictions are in good agreement with the experimental data of CO₂ solubility in aqueous blends of this work as well as those reported in the literature. The current model can also predict speciation, heat of absorption, pH of the CO₂ loaded solution, and amine volatility.     

Solubility of carbon dioxide in the solvent system (2-amino-2-methyl-1-propanol + sulfolane + water)

New sets of data for the solubility of CO₂ in the amine solvent system of 2-amino-2-methyl-1-propanol (1) + sulfolane (2) + water (3) were presented in this work. The measurements were done at temperatures of 313.2, 333.2, 353.2, and 373.2 K and CO₂ partial pressures up to 193 kPa. The investigated compositions were as follows: (i) w₁=16.5%$w_1=16.5\%$, w₂=32.2%$w_2=32.2\%$; (ii) w₁=8.2%$w_1=8.2\%$, w₂=41.2%$w_2=41.2\%$; (iii) w₁=22.3%$w_1=22.3\%$, w₂=27.7%$w_2=27.7\%$; and (iv) w₁=30.6%$w_1=30.6\%$, w₂=19.4%$w_2=19.4\%$, where w$w$ is the mass percent of the component. The present solubility data was correlated by a modified Kent–Eisenberg model. The model reasonably represents the present solubility data, not only over the considered conditions, but also for a wider range of temperatures, partial pressures, and compositions.     

Experimental and theoretical investigation of solubility of carbon dioxide in concentrated aqueous solution of 2-amino-2-methyl-1-propanol and piperazine

In this work, new experimental results for the (vapour + liquid) equilibrium (VLE) of CO₂ in piperazine (PZ)-activated concentrated aqueous 2-amino-2-methyl-1-propanol (AMP) are presented for the temperature range of (303 to 328) K and PZ concentration range of (2 to 8) wt.%, keeping the total amine concentration in the solution at 40% and 50 wt.%. The partial pressures of CO₂ are in the range of (0.2 to 1500) kPa. The electrolyte non-random two-liquid (ENRTL) theory has been used to develop the VLE model for the quaternary system (CO₂ + AMP + PZ + H₂O) to describe the equilibrium behaviour of the solution. The CO₂ cyclic capacity of these solvents is determined between the rich and lean CO₂ loadings. It is found that the CO₂ cyclic capacity increases with the addition of PZ in aqueous AMP and also with the increase in AMP concentration in the aqueous solution. However, solid precipitation has been observed for 50 wt.% total amine concentration below T = 318 K for all relative compositions of AMP and PZ in the solvent at higher CO₂ loading. The model results of equilibrium composition, pH of the loaded solution and amine volatility of the mixed solvent system, are also presented.     

Excess enthalpies of binary solvent mixtures of 1-butanol and 2-methyl-2-propanol with aniline,N-methylaniline,and N,N-dimethylaniline

The excess molar enthalpies of binary solvent mixtures of 1-butanol and 2-methyl-2-propanol with aniline, N-methylaniline, and N,N-dimethylaniline were measured with a flow microcalorimeter at 40°C. The excess enthalpies are positive for all the systems, and smaller for the mixtures of 1-butanol than the corresponding mixtures of 2-methyl-2-propanol. With respect to the anilines, the values increase in the order aniline < N-methylaniline < N,N-dimethylaniline.     

Density functional theory study on carbon dioxide absorption into aqueous solutions of 2-amino-2-methyl-1-propanol using a continuum solvation model

We used density functional theory (DFT) calculations with the latest continuum solvation model (SMD/IEF-PCM) to determine the mechanism of CO(2) absorption into aqueous solutions of 2-amino-2-methyl-1-propanol (AMP). Possible absorption process reactions were investigated by transition-state optimization and intrinsic reaction coordinate (IRC) calculations in the aqueous solution at the SMD/IEF-PCM/B3LYP/6-31G(d) and SMD/IEF-PCM/B3LYP/6-311++G(d,p) levels of theory to determine the absorption pathways. We show that the carbamate anion forms by a two-step reaction via a zwitterion intermediate, and this occurs faster than the formation of the bicarbonate anion. However, we also predict that the carbamate readily decomposes by a reverse reaction rather than by hydrolysis. As a result, the final product is dominated by the thermodynamically stable bicarbonate anion that forms from AMP, H(2)O, and CO(2) in a single-step termolecular reaction.     

CO_2在复合溶液MDEA-AMP中的溶解度

测定了CO2在复合溶液N-甲基二乙醇胺(MDEA)+2-氨基-2-甲基-1-丙醇(AMP)中的溶解度,研究了气相CO2浓度、温度和复合溶液的组分对溶解度的影响。实验获得了温度分别为25℃、30℃和40℃时,CO2在复合溶液MDEA-AMP中的溶解度。实验表明,溶解度随气相中CO2浓度升高或随AMP在复合溶液中的摩尔分数升高而升高,随温度升高而降低。     

Enthalpy of solution of CO2 in aqueous solutions of 2-amino-2-methyl-1-propanol

The enthalpies of solution of CO₂ in aqueous solution of 2-amino-2-methyl-1-propanol (AMP) 15 wt% and 30 wt% were measured at 322.5 K and pressures range from (0.2 to 5) MPa using a flow calorimetric technique. The gas solubilities were simultaneously determined from the calorimetric data. The solubilities were compared to available literature values obtained by direct measurements. The experimental enthalpies of solution were compared to the values derived from the literature vapor liquid equilibrium data. This work provides calorimetric data that will be used later for the development of a thermodynamic model to predict both solubilities and enthalpies of solution of acid gases in aqueous amine solutions.     

多亚甲基桥连双(2-氨基-5-甲基-1,3,4-噻二唑)化合物的合成与表征

通过２－氨基－５－甲基－１,３,４－噻二唑与对甲基苯磺酰氯反应后再与多亚甲基双澳反应得到新化合物（１ａ～１ｅ）,１ａ～１ｅ醇解得５个新标题化合物。并由元素分析、ＩＲ和１ＨＮＭＲ确定了所有新化合物的结构。     

Solubility of carbon dioxide in aqueous solutions of diisopropanolamine and methyldiethanolamine

The solubility of carbon dioxide in aqueous solutions of alkanolamines was measured by means of two experimental methods. The solubility of carbon dioxide was measured at 298 K with a static total pressure apparatus in solutions of water + diisopropanolamine (DIPA) having mass fraction of DIPA equal to 10.1%, 11.0% and 33.9%. The density of the water + DIPA solution was measured continuously during the experiments to investigate the changes in density introduced by the absorption of carbon dioxide. A correlation for the density of CO₂-loaded aqueous solutions of DIPA is presented.     

Gas solubility of CO2 in aqueous solutions of N-methyldiethanolamine and diethanolamine with 2-amino-2-methyl-1-propanol

Gas solubility of carbon dioxide in an aqueous solution of 32.5 wt.% N-methyldiethanolamine and 12.5 wt.% diethanolamine with 4, 6, and 10 wt.% 2-amino-2-methyl-1-propanol has been measured, at 313.15, 343.15, and 393.15 K, over a range of pressure from 3 to 2000 kPa, using a chromatographic method for analysis of the liquid phase. The results of the gas solubility are given as the partial pressure of CO₂ against its mole ratio α (mol CO₂/mol alkanolamine) and its mole fraction at each temperature studied. The solubility of CO₂ in all the systems studied decreases with an increase in temperature and increases with an increase in the partial pressure of CO₂ at a given temperature and it is a function of the concentration of the mixture of alkanolamines in solution. The enthalpy of solution of CO₂ has been calculated from the experimental solubility data.     

(S)-2-氨基-1,1-二苯基-1-丙醇的合成

以L-丙氨酸为原料,经苄基保护、格氏反应和脱苄基反应合成了(S)-2-氨基-1,1-二苯基-1-丙醇,总收率48.1%,其结构经1H NMR,IR,EI-MS和元素分析表征。     

Impact of carbon dioxide on the surface tension of 1-hexanol aqueous solutions

Effects of carbon dioxide presence on the surface tension and adsorption kinetics of 1-hexanol solutions were investigated. Experiments were performed at a range of carbon dioxide vapor pressures and varying concentrations of 1-hexanol aqueous solution. Both dynamic and steady-state surface tensions of 1-hexanol aqueous solution were found to decrease with carbon dioxide pressure, and a linear relationship was observed between the steady-state surface tension and carbon dioxide pressure. To explain the experiments, adsorption and desorption of the two species (1-hexanol and carbon dioxide) from two sides of the vapor-liquid interface were considered. A modified Langmuir isotherm, the modified Langmuir equation of state and the modified kinetic transfer equation were developed. The resulting steady-state and dynamic surface tension data were modeled using the modified Langmuir equation of state and the modified kinetic transfer equation, respectively. Equilibrium constants and adsorption rate constants of 1-hexanol and carbon dioxide were evaluated through a minimization procedure for CO₂ pressures ranging from 0 to 690 kPa. From the steady-state modeling, the equilibrium parameters for 1-hexanol and carbon dioxide adsorption from vapor phase and liquid phase were found unchanged at different pressures of carbon dioxide. From the dynamic modeling, the adsorption rate constants for 1-hexanol and carbon dioxide from vapor phase and liquid phase were found to decrease with carbon dioxide pressure. Some fluctuations in the fitting parameters of the dynamic modeling (adsorption rate constants) were observed. These fluctuations may be due to experimental errors, or more likely the limitations of the model used. A major limitation of the model is related to large differences in adsorption/desorption between initial and final stages of the process, and a single set of property parameters cannot describe both initial and final states of the system. Variations may occur depending on which set of data, of initial or final states, is used in the model predictions over the entire time range.     

On the lead tetraacetate oxidation of 4-amino-1,2,4-triazoles, 1-amino- and 2-amino-1,2,3-triazoles

Lead tetraacetate oxidation of 4-amino-1,2,4-triazoles, 1-amino- and 2-amino-1,2,3-triazoles affords mainly fragmentation to nitriles or acetylenes, even in the presence of intramolecularly attached double bonds.

---

Über die Bleitetraacetatoxidation von 4-Amino-1,2,4-triazolen, 1-Amino- und 2-Amino-1,2,3-triazolen (Kurze Mitteilung)

Zusammenfassung Bei der Oxidation von 4-Amino-1,2,4-triazolen, 1-Amino- und 2-Amino-1,2,3-triazolen mit Bleitetraacetat entstanden hauptsächlich Nitrile bzw. Acetylene durch Fragmentierung — trotz der Gegenwart von intramolekularen Doppelbindungen.

     

Liquid-vapor equilibrium of dilute aqueous solutions of ethanol and 2-propanol

An automated vapor pressure apparatus has been used to obtain highly precise values of the total pressure and composition of aqueous solutions of ethanol and of 2-propanol in the water-rich region at 25 and 35°C. From these results, values of the partial pressures and fugacities of the components and osmotic coefficients have been inferred. Interaction virial coefficients derived from the present results are compared with interaction parameters previously reported for alcohol molecules in dilute aqueous solution. A discussion is given of the relative importance of hydrophobic effects and hydrogen-bonding in producing the unusual thermodynamic properties of aqueous alcohol solutions.     

Reactive kinetics of carbon dioxide loaded aqueous blend of 2-amino-2-ethyl-1,3-propanediol and piperazine using a pressure drop method

In this study, a new pressure drop method has been used to investigate the kinetics of carbon dioxide reaction with aqueous blend of 2-amino-2-ethyl-1,3-propanediol (AEPD) with piperazine (PZ). The blending of a small amount of PZ with AEPD has a significant effect on the observed rate constant, k_obs. It was observed that k_obs values of the blend increased more than twice than the summation of k_obs values of individual alkanolamines. The reaction kinetics in this study were modeled by assuming a termolecular mechanism. The addition of 0.1 mol/L of PZ to 1 mol/L AEPD exhibited an observed rate constant, k_obs of 8824.1 s⁻¹, which is comparable to other alkanolamine mixtures. Hence, PZ/AEPD mixtures can be potentially used for rapid carbon dioxide capture.     

Equilibrium conditions of clathrate hydrates formed from carbon dioxide and aqueous acetone solutions

Equilibrium conditions of clathrate hydrates formed from carbon dioxide and aqueous acetone solutions were experimentally measured at temperatures between 269.2 and 281.4 K and pressures up to 3.98 MPa. The acetone concentrations in solutions were investigated from 0.04 to 0.40 mass fractions. The experimental results suggested a transition in hydrate structure from structure I to another structure for acetone solutions between 0.04 and 0.12 mass fractions of acetone. The hydrate structure was suggested to be structure II which was the most stable with a 0.16 mass fraction acetone solution. For more than 0.16 mass fraction of acetone, the equilibrium conditions of the hydrate were shifted to lower temperatures as acetone concentrations increased.     

Phase equilibria of mixed carbon dioxide and tetrahydrofuran hydrates in sodium chloride aqueous solutions

In this work, the competing effects of sodium chloride (NaCl) and tetrahydrofuran (THF) on carbon dioxide hydrate formation are investigated through phase equilibrium measurements. The phase behaviour in the hydrate forming region for the binary system carbon dioxide–water, the ternary systems carbon dioxide–tetrahydrofuran–water and ternary carbon dioxide–sodium chloride–water and, in addition, the quaternary system carbon dioxide–tetrahydrofuran–water–sodium chloride are determined experimentally, using a Cailletet apparatus. All measurements are made in a temperature and pressure region of 275–290 K and 0.5–7.0 MPa, respectively. In these ranges, three different hydrate equilibrium curves are measured namely: H-L_W-V, H-L_W-L_V-V and H-L_W-L_V. The formation of an organic-rich liquid phase in the systems due to a liquid–liquid two-phase split between water and tetrahydrofuran when pressurized with carbon dioxide causes the occurrence of an upper quadruple point (Q₂) to evolve into a four-phase H-L_W-L_V-V equilibrium line. The presence of sodium chloride in the quaternary system enhances the split between the two liquids due to the salting-out effect. It was found that the hydrate promoting effect of tetrahydrofuran is able to suppress the inhibiting effect of sodium chloride especially at lower concentration of sodium chloride.     

Solubility of carbon dioxide in 1-ethyl-3-methylimidazolium 2-(2-methoxyethoxy) ethylsulfate

Experimental results for the solubility of carbon dioxide in the ionic liquid 1-ethyl-3-methylimidazolium 2-(2-methoxyethoxy) ethylsulfate are not reported in the literature. To this end, we present in this work new solubility data for carbon dioxide in 1-ethyl-3-methylimidazolium 2-(2-methoxyethoxy) ethylsulfate for temperatures ranging from (303.2 to 343.2) K and pressures up to 6.7 MPa using a thermogravimetric microbalance. The carbon dioxide solubility was determined from absorption saturation (equilibrium) data at each fixed temperature and pressure. The buoyancy effect was accounted in the evaluation of the carbon dioxide solubility. Highly accurate equations of states for carbon dioxide and for ionic liquids were employed to determine the effect of buoyancy on carbon dioxide solubility. The solubility measurements are presented as a function of temperature and pressure. The present experimental solubility results have been successfully correlated using an extended Henry’s law equation.     

Experimental study on equilibrium solubility (at low partial pressures), density, viscosity and corrosion rate of carbon dioxide in aqueous solutions of ascorbic acid

In this paper, ascorbic acid as a new carbon dioxide (CO₂) absorbent was investigated. The equilibrium solubility of CO₂ into 0.5, 1 and 1.5 mol dm⁻³ (M) aqueous ascorbic acid solutions were measured experimentally with a stirred batch reactor at total atmospheric pressure over the CO₂ partial pressure ranging from 0 to 45 kPa and temperatures between 298 and 313 K. The results of the gas solubility are presented as loading capacity (mol CO₂/mol ascorbic acid) as function of partial pressure of CO₂ for all experimental runs. Experimental results showed that solubility of CO₂ increases with increase in molar concentration of ascorbic acid solution at a given temperature and decreases with increase in temperature at a given concentration. The densities and viscosities of the ascorbic acid solutions were measured at the same conditions of the solubility measurement. Some corrosion rate tests were also performed on carbon steel at temperature of 308 K. It was observed that viscosity and corrosion rate increase when the molar concentration of ascorbic acid solution increases.     

Phase-transfer oxidation of 2-methyl-1-naphthol into 2-methyl-1,4-naphthoquinone in the presence of vanadomolybdophosphoric heteropolyacids

2-Methyl-1-naphthol is oxidized into 2-methyl-1,4-naphthoquinone (menadione) by air in the presence of vanadomolybdophosphoric heteropolyacids and their salts. The reaction proceeds in a biphasic system, and the yield of menadione is up to 85 %. The influence of the composition of the heteropolyacids on the rate and the selectivity of the reaction was studied, and the reaction mechanism was proposed.Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 7, pp. 1208–1211, July, 1994.