AB型聚乙二醇单甲醚-聚(L-丙氨酸)嵌段共聚物自组装过程的核磁共振研究

利用核磁共振方法研究了AB型双嵌段共聚物(MPEG45-b-PA32)在选择性溶剂中的自组装行为及胶束化过程.嵌段共聚物在三氟乙酸中聚氨基酸和聚乙二醇链段均处于自由运动状态,聚丙氨酸链段为无规线团结构.在向该溶液中逐渐加入氘代水的过程中,聚丙氨酸链段又重新聚集形成规整的二级结构.结合1H-NMR和COSY谱分析,结果显示这一自组装过程伴随着聚(L-丙氨酸)链段由无规线团向α-螺旋结构的构象转变,同时嵌段共聚物逐渐形成核-壳型胶束结构.利用透射电镜观察了所形成胶束的形态,嵌段共聚物主要形成粒径150 nm到220 nm的球形胶束.     

用1H NMR方法研究聚砜-聚脂类嵌段共聚物的组成和序列分布

本文测定了一系列聚矾-聚酯嵌段共聚物的高分辨核磁共振谱,研究了共聚物的组成和序列分布,山¹HNMR谱图的峰面积算出了共聚物的无规度(B)及数均序列长度(L),B值均在O相似文献   

运用1H-NMR和13C-NMR研究聚对苯二甲酸-2,5-呋喃二甲酸乙二醇共聚酯（PEFT）的序列结构

采用直接酯化法,通过改变对苯二甲酸(PTA)与2,5-呋喃二甲酸(FDCA)的摩尔比,制备了一系列聚对苯二甲酸-2,5-呋喃二甲酸乙二醇共聚酯(PEFT)。运用1H-NMR和13C-NMR测试手段研究PEFT共聚酯的链结构。通过观察PEFT共聚酯链上乙二醇单元中氢原子和碳原子的化学位移及相应的4种信号的强度变化,计算出共聚酯的数均序列长度(L),无规度值(B)和共聚物的组成。通过Yamadera和Murano公式计算所得共聚酯无规度值B均接近于1,说明PEFT共聚酯为无规共聚物;PEF-block-PET嵌段共聚物B为0.577,PEF-blend-PET共混物的B为0;差示扫描量热仪(DSC)测试结果表明,0PEFT共聚酯均有一个玻璃化温度,进一步说明了PEFT共聚酯为无规共聚物。其中PTA∶FDCA的摩尔比为1∶1时,即PEFT-50,B值最大,基于1H-NMR谱图计算得B=1.012,13C-NMR谱图计算得B=1.028。上述结果表明,2,5-呋喃二甲酸与对苯二甲酸在与乙二醇的亲核取代反应中活性相近。     

聚(苯乙烯-丁二烯-苯乙烯)三嵌段共聚物链结构的研究

<正> 以丁基锂引发二步加料法制备聚(苯乙烯-丁二烯-苯乙烯)三嵌段共聚物(简称SBS),往往在共聚物的中间链段聚丁二烯段中含有少量苯乙烯,即中间链段末端含有部份无规丁苯,得不到很纯的三嵌段共聚物,本文用超导核磁共振仪(H~1-NMR)、傅立叶红外光谱仪(FT-IR)、粘弹谱仪研究了上述SBS链结构,发现非嵌段苯乙烯芳环质子共振峰由二     

茂金属化合物/Zn/BDGE/MAO催化体系合成aPS-b-P(S-co-E)-b-PE嵌段共聚物的研究

采用单茂钛化合物CpTiCl3,有机环氧化合物1,4-丁二醇二缩水甘油基醚(BDGE),金属锌(Zn)及甲基铝氧烷(MAO)为催化体系,通过自由基聚合和配位聚合机理合成无规聚苯乙烯-b-聚(苯乙烯-co-乙烯)-b-聚乙烯(aPS-b-P(S-co-E)-b-PE).探讨了温度、时间、乙烯压力及Al/Ti摩尔比对共聚合的影响.所得嵌段共聚物采用DSC,WAXD,GPC和13C-NMR等手段进行了表征.结果表明该共聚物是苯乙烯/乙烯嵌段共聚物,聚苯乙烯链段是无规的,聚乙烯链段具有结晶性.     

一种光学活性三嵌段共聚物的ATRP合成及表征

以溴代聚砜为大分子引发剂,三(2-二甲氨基乙基)胺(Me6TREN)/CuBr为催化体系,通过原子转移自由基聚合(ATRP)制备了结构预定且分子量分布窄的光学活性三嵌段共聚物,聚(N-甲基丙烯酰-L-亮氨酸甲酯)-嵌-聚砜-嵌-聚(N-甲基丙烯酰-L-亮氨酸甲酯)(PMALM-b-PSF-b-PMALM).通过核磁共振氢谱(1H-NMR)、凝胶渗透色谱(GPC)、端羟基滴定等方法,研究了所合成的三嵌段共聚物的结构.利用差示扫描量热法(DSC)、热失重分析(TGA)以及圆二色谱(CD)研究了嵌段共聚物的热性能和旋光性能.根据TGA计算出的PMALM链段与PSF链段的重复单元数之比,与1H-NMR计算的结果能较好的吻合.共聚物在聚合过程中旋光度发生了反转,且比单体的旋光度的绝对值显著增加,这可能是由于聚合过程中分子主链感应出了手性的二级结构诱导出手性放大效应引起的.在CH3OH/CCl4混合溶剂中,共聚物比旋光度的绝对值随溶剂极性增大呈线性减小趋势,这一结果与CD一起证实了PMALM链段的无规卷曲结构.     

光学活性两亲性嵌段共聚物的合成与表征

以溴封端聚乙二醇单甲醚(MPEG-Br)为大分子引发剂,三(2-二甲氨基乙基)胺(Me6TREN)/溴化亚铜(CuBr)为催化体系,通过原子转移自由基聚合(ATRP)反应制备了不同嵌段比例且分子量分布较窄的光学活性聚乙二醇单甲醚嵌段聚(N-甲基丙烯酰-L-亮氨酸甲酯)(MPEG-b-PMALM)聚合物.以1H-NMR表征了其化学结构以及两嵌段的比例.通过热重分析(TGA)和示差扫描量热仪(DSC)研究了嵌段共聚物的热学性能.相对于单体的旋光度,共聚物在聚合过程中旋光度发生了反转,其旋光度的绝对值显著增加,且随着PMALM嵌段含量的增加而增加.圆二色谱法(CD)结果表明,嵌段共聚物分子主链形成了一种无规卷曲的二级构象结构,其光学活性亦随PMALM含量的增加而增强.     

苯并噁唑脲/MTBD催化L-丙交酯和δ-戊内酯开环共聚合

以苯并噁唑脲(NO)为催化剂,与杂二环[4.4.0]癸-5-烯(MTBD)协同,进行了L-丙交酯的开环聚合以及δ-戊内酯与L-丙交酯的开环共聚合,采用核磁共振波谱(NMR)分析了共聚物的序列结构,原料预混合下所得共聚物的随机度(R)为0.5左右,介于完全无规共聚物和嵌段共聚物之间.采用示差扫描量热分析(DSC)测试了均聚物和共聚物的热性能,共聚物中两单体含量接近时,没有观察到熔融峰的出现,且样品在常温下呈橡胶态,为无定形聚合物;随着戊内酯(VL)链段的减少,共聚物的玻璃化转变温度升高.嵌段共聚物的分子序列可控,随机度趋近于0.     

聚(L-丙氨酸-co-羟丙-L-谷氨酰胺)无规共聚物的两亲性及其胶束行为研究

采用丙氨酸作为疏水聚合单体,谷氨酸作为亲水聚合单体,一步开环聚合反应,合成了具有两亲性的聚氨基酸无规共聚物.利用IR,1H-NMR等方法对所合成的聚合物进行了详细的表征,结果表明两种单体都能够按照投料比参加聚合反应生成无规共聚物.对比聚丙氨酸-聚羟丙谷氨酰胺嵌段共聚物,探讨了无规共聚物与嵌段共聚物在两亲性及结构性质上的差异和特点.研究表明,聚(L-丙氨酸-co-羟丙-L-谷氨酰胺)无规共聚物与嵌段共聚物一样,具有两亲性,在水溶液中也能够形成胶束,但胶束尺寸较嵌段共聚物要小,胶束形态也不像嵌段共聚物是规整的球形.实验发现,亲疏水单体的比例对胶束的形成有很大影响,P(A10-co-HPG40)所制得的胶束分散最为均匀.所形成的胶束以疏水的聚丙氨酸为内核,亲水的聚羟丙谷氨酰胺为外壳.     

聚己内酯-聚丙交酯-聚醚三元共聚高分子微粒及其降解的研究

用乳化－ 溶剂蒸发法制备了聚己内酯－ 聚丙交酯－ 聚醚三元无规共聚物微粒,且与用相同方法制备的聚己内酯（ＰＣＬ） 和聚己内酯－ 聚醚嵌段共聚物微粒的形态进行了比较,讨论了材料的亲水性,以及三元无规共聚物中亲水性聚醚链段的长度及含量对所形成微粒形态的影响。研究结果表明,随着聚合物由疏水性向亲水性转变,所生成微粒的形态则从光滑、多孔、到不规则变化。证明了三元无规共聚物多孔微粒的形成是由于亲水的聚醚链段向水相取向所致。在３７ ℃、ｐＨ７ ．４ 的缓冲液中进行了三元无规共聚物微粒的降解,结果表明,随着降解时间的延长, 三元无规共聚物的分子量逐渐下降,且其中的聚醚链段含量有明显的降低。     

Sequence analysis of poly (ether sulfone) copolymers by 13C NMR

Random and block copolymers of poly (ether sulfone) (PES) and poly (ether ether sulfone) (PEES) were synthesized by the nucleophilic polycondensation of 4,4′‐dichlorodiphenyl sulfone (DCDPS) with 4,4′‐dihydroxydiphenyl sulfone (DHDPS) and hydroquinone (HQ). Chemical structures of these copolymers were characterized by ¹³C NMR. The monomer molar fraction, sequential distribution, and degree of randomness of the copolymers were determined through analyses of the resonances of quaternary carbons in the DCDPS unit. Experimental results show that the molar fractions of the comonomer determined by ¹³C NMR analyses are close to the charged values in the synthetic step. Moreover, these copolymers, which were prepared by different polymerization methods, revealed different number‐average sequential length and degree of randomness. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 1624–1630, 2005     

含亚环己基荷电聚醚醚酮的合成表征与性能

以 3,3′ 二磺酸钠基 4,4′ 二氟二苯酮和 4,4′ 二氟二苯酮与 4,4′ 亚环己基双酚进行亲核共缩聚 ,合成了磺化度从 0 4～ 2 0的一系列含亚环己基的荷电聚醚醚酮 .聚合物除保持了荷电聚醚醚酮良好的热稳定性和机械性能外 ,还具有良好的耐水性 .聚合物的DSC和广角X射线衍射数据表明 :上述磺化度聚合物均呈无定型聚集态结构 .比较了聚合物与双酚A系列荷电聚醚醚酮的性能差异 ,讨论了聚合物的溶解特点     

Investigations of aromatic polyesters with polynaphthalene systems in the main chain—VI: NMR studies of the structure of the aromatic copolyesters

Nuclear magnetic resonance spectra of several kinds of terephthalic copolyesters of 4,4′dihydroxydinaphthyl 1,1′ and 2,2 bis(4-hydroxyphenyl) propane were recorded. Proton signals of the terephthalic acid unit corresponding to heterolinkages and homolinkages could be observed in the range from 8.23 to 8.53 ppm. The average sequence lengths and the degrees of randomness in the copolyesters were calculated from the intensities of these signals.     

Controlled sulfonation of poly(arylene ether sulfone)s and poly(arylene ether ketone)s with different molecular structures for polymer electrolyte membranes

Poly(arylene ether sulfone) copolymers derived from 9,9-bis(4-hydroxyphenyl)fluorene, bisphenol S and 4,4′-difluorodiphenylsulfone and poly(arylene ether ketone) copolymers derived from 4-phenoxybiphenyl, diphenyl ether and isophthaloyl chloride were prepared as precursor polymers for sulfonation reaction in which sulfonic groups are introduced quantitatively into specified positions. Sulfonation reaction for these two series of copolymers by concentrated sulfuric acid was successfully carried out to give sulfonated polymers with controlled positions and degree of sulfonation. Thermal stability, moisture absorption and proton conductivity for these two series of copolymers were measured and the results were compared to those of perfluorosulfonic acid polymers.     

Synthesis and Properties of Poly(Aryl Ether Ketone) Copolymers with Trifluoromethyl‐Substituted Benzene in the Side Chain

The new monomer (4‐(4′‐trifluoromethyl)phenoxyphenyl)hydroquinone (TFPOPH) was synthesized in a three‐step synthesis. A series of poly(aryl ether ketone) copolymers were prepared by the reaction of (4‐(4′‐Trifluoromethyl)phenoxyphenyl)hydroquinone and hydroquinone (HQ) with 4,4′‐difluorobenzophenone (DFB) in the presence of potassium carbonate in tretramethylene sulfone (TMS). Thermal analyses of the fluorinated copolymers showed that the glass transition temperature and 5.0% weight loss temperature are similar with that of PEEK, and the crystallinity decreased with increasing of TFPOPH. For the copolymer synthesized with the molar fraction of TFPOPH in the diphenol monomers (TFPOPH, HQ) being over 0.2, no cold crystallization temperature and melting temperature were detected, indicating that these copolymers are almost amorphous. The crystal structure of the copolymers with the molar fraction of TFPOPH being not higher than 0.2 is rhombic. The solubility in polar aprotic solvents of poly(aryl ether ketone)s copolymers increases and dielectric constant decreases step by step.     

一种杂环磺化聚芳醚腈酮质子交换膜材料的合成及表征

用含二氮杂萘酮结构类双酚DHPZ,3,3′-二磺酸钠基-4,4′-二氟二苯酮,2,6-二氯苯腈以及4,4′-二氟二苯酮,通过缩合共聚合反应合成了一系列不同磺化度、高分子量的磺化聚芳醚腈酮.聚合物特性粘数为0·58~2·0dL/g.用红外光谱(FT-IR),核磁共振谱(1H-NMR)表征了聚合物结构.用差示扫描量热仪(DSC)和热重分析仪(TGA)研究了聚合物的耐热性能,研究表明其玻璃化温度(Tg)可达352℃,5%热失重温度大于500℃.以N-甲基吡咯烷酮为溶剂,溶液浇铸法制备了聚合物膜,并测定了膜的溶胀率以及质子交换能力.结果表明,与Nafion膜相比,磺化聚芳醚腈酮膜在相同的质子交换能力条件下,溶胀率显著降低.     

Synthesis and characterization of poly(arylene ether sulfone) copolymers with sulfonimide side groups for a proton‐exchange membrane

A sulfonimide‐containing comonomer derived from 4,4′‐dichlorodiphenylsulfone was synthesized and copolymerized with 4,4′‐dichlorodiphenylsulfone and 4,4′‐biphenol to prepare sulfonimide‐containing poly(arylene ether sulfone) random copolymers (BPSIs). These copolymers showed slightly higher water uptake than disulfonated poly(arylene ether sulfone) copolymer (BPSH) controls, but their proton‐conductivity values were very comparable to those of the BPSH series with similar ion contents. The proton conductivity increased with the temperature for both systems. For samples with 30 mol % ionic groups, BPSI showed less temperature dependence in proton conductivity and slightly higher methanol permeability in comparison with BPSH. The thermal characterization of the sulfonimide copolymers showed that both the acid and salt forms were stable up to 250 °C under a nitrogen atmosphere. The results suggested that the presumed enhanced stability of the sulfonimide systems did not translate into higher protonic conductivity in liquid water. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 6007–6014, 2006     

Influence of the bisphenol structure on the direct synthesis of sulfonated poly(arylene ether) copolymers. I

New sulfonated poly(arylene ether sulfone) copolymers with high molecular weights were successfully synthesized with controlled degrees of disulfonation of up to 70 mol % via the direct copolymerization of sulfonated aromatic dihalides, aromatic dihalides, and one of four structurally distinct bisphenols. The disodium salts of the 3,3′‐disulfonated‐4,4′‐dichlorodiphenyl sulfone and 3,3′‐disulfonated‐4,4′‐difluorodiphenyl sulfone comonomers were synthesized via the sulfonation of 4,4′‐dichlorodiphenyl sulfone or 4,4′‐difluorodiphenyl sulfone with 30% fuming sulfuric acid at 110 °C. Four bisphenols (4,4′‐bisphenol A, 4,4′‐bisphenol AF, 4,4′‐biphenol, and hydroquinone) were investigated for the syntheses of novel copolymers with controlled degrees of sulfonation. The composition and incorporation of the sulfonated repeat unit into the copolymers were confirmed by ¹H NMR and Fourier transform infrared spectroscopy. Solubility tests on the sulfonated copolymers confirmed that no crosslinking and probably no branching occurred during the copolymerizations. Tough, ductile films were solvent‐cast that exhibited increased water absorption with increasing degrees of sulfonation. These copolymers are promising candidates for high temperature proton‐exchange membranes in fuel cells, which will be reported separately in part II of this series. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 2264–2276, 2003     

Thermotropic copolyamides from triethyleneglycol bis(4-carboxyphenyl)ether,aromatic diamines,and p-aminobenzoic acid modified by the monomer sequences in the copolyamides

Copolycondensations of triethyleneglycol bis(4-carboxyphenyl)ether (PEG₃), p-amino-benzoic acid (PABA), and p-phenylenediamine (PPD) were studied in order to examine the effect of monomer sequences in the copolyamides upon the transition temperatures of the resulting copolymers. Random copolymerization of these monomers resulted in the copolymers exhibiting a nematic mesophase in a wide range of PABA content. On the other hand, the sequential copolymers composed of PABA/PPD = 1/1 and 2/1, which were prepared from 4,4′-diaminobenzanilide (DABA) and N,N′-bis(4-aminobenzoyl)-p-phenylenediamine (BAB-PPD), respectively, did not show a mesophase. The copolymers of a diamine combination of DABA and PPD exhibited a nematic mesophase, despite the lack of a mesophase for each homopolymer. The combinations of DABA and other diamines were also examined. © 1994 John Wiley & Sons, Inc.     

Direct copolymerization of sulfonated poly(phthalazinone arylene ether)s for proton‐exchange‐membrane materials

Sulfonated poly(phthalazinone ether ketone) (SPPEK) copolymers and sulfonated poly(phthalazinone ether sulfone) (SPPES) copolymers containing pendant sodium sulfonate groups were prepared by direct copolymerization. The reaction of disodium 3,3′‐disulfonate‐4,4′‐difluorobenzophenone (SDFB‐Na), 4,4′‐difluorobenzophenone (DFB), and 4‐(4‐hydroxyphenyl)‐1(2H)‐phthalazinone (DHPZ) at 170 °C in N‐methyl‐2‐pyrrolidione containing anhydrous potassium carbonate gave SPPEKs. SPPESs were similarly obtained with 3,3′‐disulfonate‐4,4′‐difluorophenyl sulfone, 4‐fluorophenyl sulfone (DFS), and DHPZ as monomers. The sulfonic acid groups, being on deactivated positions of the polymer backbone, were expected to be hydrolytically more stable than postsulfonated polymers. Fourier transform infrared and ¹H NMR were used to characterize the structures and degrees of sulfonation of the sulfonated polymers. Membrane films of SPPEKs with SDFB‐Na/DFB molar feed ratios of up to 60/40 and SPPESs with sulfonated 4‐fluorophenyl sulfone/DFS molar feed ratios of up to 50/50 were cast from N,N‐dimethylacetamide polymer solutions. Membrane films in acid form were then obtained by the treatment of the sodium‐form membrane films in 2 N sulfuric acid at room temperature. An increase in the number of sulfonate groups in the copolymers resulted in an increased glass‐transition temperature and enhanced membrane hydrophilicity. The sodium‐form copolymers were thermally more stable than their acid forms. The proton conductivities of the acid‐form copolymers with sulfonated monomer/unsulfonated monomer molar feed ratios of 0.5 and 0.6 were higher than 10^?2 S/cm and increased with temperature; they were less temperature‐dependent than those of the postsulfonated products. SPPESH‐50 showed higher conductivity than the corresponding postsulfonated poly(phthalazinone ether sulfone). © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 2731–2742, 2003