Compensation for matrix effects in gas chromatography–tandem mass spectrometry using a single point standard addition

One of the major problems in quantitative analysis of pesticide residues in food samples by gas chromatography–tandem mass spectrometry (GC–MS/MS) is the enhancement or the suppression, of the target analyte signals in matrix extracts. Potentially positive samples, which had previously been identified by a rapid screening method, were quantified using standard addition to compensate matrix effects. As example we performed a systematic study on the application of the standard addition calibration (SAC) method for the determination of 12 pesticides (acephate, bromopropylate, chlorpyrifos, cypermethrin, diazinon, etrimfos, heptenophos, iprodione, methamidophos, procymidone, tetradifon, and triadimefon) in two matrices (cucumber and orange) in the range of initial concentrations of 10–200 μg kg⁻¹. The influence of some factors, such as the minimum number of standard additions used (single, two, three or four points calibration), as well as the known amount of analyte added to the sample, is evaluated in order to obtain reliable results. Accurate quantification is achieved when a single point SAC at 200 μg kg⁻¹ was used, obtaining for all the cases recoveries between 70 and 120%. The proposed analytical approach only needs two injections per sample (blank and spiked extracted sample) to determine the final concentration of pesticide in positive samples.     

Solvent-free MALDI-MS: Developmental improvements in the reliability and the potential of MALDI in the analysis of synthetic polymers and giant organic molecules

A dry sample preparation strategy was previously established as a new method for matrix assisted laser desorption/ionization mass spectrometry (MALDI-MS), so-called solvent-free MALDI-MS. In this contribution, we examine systems that have been shown problematic with conventional solvent-based MALDI approaches. Problems frequently encountered are solubility, miscibility, and segregation effects during crystallization as a result of unfavorable analyte and matrix polarities. In all cases studied, solvent-free MALDI-MS simplified the measurement and improved the analysis. Solvent-free MALDI-MS enables more reliable results in well-known problematic systems such as polydimethylsiloxane with its segregation effects. However, even in highly compatible analyte/matrix systems such as polystyrene and dithranol, there were undesirable suppression effects when employing THF as solvent. Generally, the solvent-free method allows for more homogeneous analyte/matrix mixtures as well as higher shot-to-shot and sample-to-sample reproducibility. As a result, less laser power has to be applied, which yields milder MALDI conditions, reduced background signals, and provides better resolution of the analyte signals. Solvent-free MALDI-MS proved valuable for the characterization of nanosized material, e.g., fullereno-based structures, which indicated having an increased fragmentation-susceptibility. New analyte/matrix combinations (e.g., polyvinylpyrrolidone/dithranol) are accessible independent of solubility and compatibility in common solvents. An improved quantitation potential is recognized (e.g., insoluble polycyclic aromatic hydrocarbon against soluble dendrite precursor). The rapid and easy measurement of industrial products demonstrates the solvent-free method capable for improved throughput analysis of a variety of compounds (e.g., poly(butylmethacrylate) diol) in routine industrial analysis. Hence, this new MALDI method leads to qualitative and quantitative improvements, making it a powerful tool for analytical purposes, which may also prove to be valuable in future automation attempts.     

A sample preparation method for recovering suppressed analyte ions in MALDI TOF MS

In matrix‐assisted laser desorption/ionization time‐of‐flight mass spectrometry (MALDI TOF MS), analyte signals can be substantially suppressed by other compounds in the sample. In this technical note, we describe a modified thin‐layer sample preparation method that significantly reduces the analyte suppression effect (ASE). In our method, analytes are deposited on top of the surface of matrix preloaded on the MALDI plate. To prevent embedding of analyte into the matrix crystals, the sample solution were prepared without matrix and efforts were taken not to re‐dissolve the preloaded matrix. The results with model mixtures of peptides, synthetic polymers and lipids show that detection of analyte ions, which were completely suppressed using the conventional dried‐droplet method, could be effectively recovered by using our method. Our findings suggest that the incorporation of analytes in the matrix crystals has an important contributory effect on ASE. By reducing ASE, our method should be useful for the direct MALDI MS analysis of multicomponent mixtures. Copyright © 2015 John Wiley & Sons, Ltd.     

Lipid fingerprinting of gram-positive lactobacilli by intact--matrix-assisted laser desorption/ionization mass spectrometry using a proton sponge based matrix

A method of direct lipid analysis by matrix-assisted laser desorption/ionization (MALDI) mass spectrometry (MS) in intact membranes, without prior extraction/separation steps, is described. Here, we demonstrate the efficacy of a strong base, 1,8-bis(dimethylamino)naphthalene (DMAN; proton sponge), as a novel matrix for MALDI-time-of-flight (TOF) MS analysis of whole cell bacteria. Initially, individual acidic low-molecular-weight analytes such as standard free fatty acids and phospholipids were analyzed using DMAN as matrix. Clear negative-mode MALDI-TOF MS spectra of all analytes show only deprotonated analyte signals at a low picomole limit of detection with the complete absence of matrix-related signals. These results indicate that DMAN represents a suitable matrix for MALDI-TOF MS analysis of mixtures of complex lipids as the intact membranes of microorganisms. DMAN was successfully applied to the analysis of Lactobacillus sanfranciscensis and L. plantarum microorganisms. Different components were sensitively detected in a single spot, including 16:0, 18:2, 18:3, and 21:0 free acids, glycolipids, phosphatidylglycerols (PGs) and cardiolipins. This method might be of general application, offering the advantage of quickly gaining information about lipid components of other gram-positive bacterial membranes.     

Multiple headspace solid-phase microextraction for eliminating matrix effect in the simultaneous determination of haloanisoles and volatile phenols in wines

This paper proposes a multiple headspace solid-phase microextraction (MHS-SPME) method coupled to gas chromatography-tandem mass spectrometry detection (GC/MS/MS) for the simultaneous determination of 2,4,6-trichloroanisole, 2,3,4,6-tetrachloroanisole, pentachloroanisole, 2,4,6-tribromoanisole, 4-ethylphenol, 4-ethylguaiacol, 4-vinylphenol and 4-vinylguaiacol in wines. These compounds are involved in the presence of "cork taint" and Brett character in wines. The MHS-SPME method is a modification of SPME developed for quantitative analysis that avoids possible matrix effects based on an exhaustive analyte extraction from the sample. After demonstrating the existence of matrix effect in the analysis of the target compounds by HS-SPME with a divinylbenzene/Carboxen/polydimethylsiloxane (DVB/CAR/PDMS) fibre, the MHS-SPME method was developed and validated. The proposed method showed satisfactory linearity, precision and detection limits, all below the odour detection thresholds of the compounds in wine matrices. Good recoveries were observed for all compounds, always above 90%, and the repeatability obtained was considered acceptable, ranging between 2 and 11%. After checking the applicability of the method by comparing the results recorded with those obtained with the standard addition method, the method was applied successfully to the analysis of wine samples. To our knowledge, this is the first time that MHS-SPME combined with GC/MS/MS has been applied to simultaneously determine haloanisoles and volatile phenols in wine.     

Phospholipids in liquid chromatography/mass spectrometry bioanalysis: comparison of three tandem mass spectrometric techniques for monitoring plasma phospholipids,the effect of mobile phase composition on phospholipids elution and the association of phospholipids with matrix effects

Because plasma phospholipids may cause matrix effects in bioanalytical liquid chromatography/tandem mass spectrometry (LC/MS/MS) methods, it is important to establish optimal mass spectrometric techniques to monitor the fate of phospholipids during method development and application. We evaluated three MS/MS techniques to monitor phospholipids using positive and negative electrospray ionization (ESI). The first technique is based on using positive precursor ion scan of m/z 184, positive neutral loss scan of 141 Da and negative precursor ion scan of m/z 153. The second technique is based on using class‐specific positive and negative selected reaction monitoring (SRM) transitions to monitor class‐representative phospholipids. The third technique, previously reported, utilizes in‐source collision‐induced dissociation (CID)‐based positive SRM of m/z 184 → 184. We recommend the all‐inclusive technique 1 for use in qualitative assessment of all classes of phospholipids and technique 2 for use in quantitative assessment of class‐representative phospholipids. Secondly, we evaluated the elution behaviors of the plasma phospholipids under different reversed‐phase mobile phase conditions. The phospholipid‐eluting strength of a mobile phase was mainly dependent on the type and amount (%) of the organic eluent and the strength increased in the order of methanol, acetonitrile and isopropyl alcohol. Under the commonly used gradient and isocratic elution schemes in LC/MS/MS bioanalysis, not all the phospholipids are eluted off the column. Thirdly, we investigated the association between phospholipids and matrix effects in positive and negative ESI using basic, acidic and neutral analytes. While the phospholipids caused matrix effects in both positive and negative ESI, the extent of ionization suppression was analyte‐dependent and was inversely related to the retention factor and broadness of the phospholipids peaks. The lysophospholipids which normally elute earlier in reversed‐phase chromatography are more likely to cause matrix effects compared to the later‐eluting phospholipids in spite of the larger concentrations of the latter in plasma. Copyright © 2009 John Wiley & Sons, Ltd.     

分析保护剂补偿基质效应-气相色谱-质谱法快速测定水果中40种农药残留

建立了水果中40种农药化合物的气相色谱-质谱(GC-MS)多残留检测方法,评价了添加分析保护剂对农药残留分析的补偿基质效应和对定量结果可靠性的影响。采用可以溶于丙酮有机溶剂的聚乙二醇Polyethylene Glycol 400(PEG 400)和橄榄油作为保护剂组合进行定量分析。水果样品采用乙腈提取,微型固相萃取小柱净化,大体积进样,GC-MS选择离子监测(SIM)模式检测。40种农药化合物在1～200 μg/L范围内线性关系良好,线性相关系数在0.99以上,检出限(以信噪比为3计)为0.1～3.0 μg/L。除乐果外,其他化合物的添加回收率为75%～119%,相对标准偏差均小于16.6%。通过对添加分析保护剂的校准曲线与基质匹配校准曲线的定量准确性的比较,发现加入分析保护剂方法可以代替基质匹配校正方法,同时采用大体积进样和微型固相萃取净化相结合的方法,大大减少了样品前处理量。将所建立的分析保护剂方法用于苹果、桃子、橙子、香蕉和葡萄等水果样品的分析,基质补偿效应良好,有效地克服了水溶性分析保护剂对气相色谱分析有影响的缺点。     

Combating matrix effects in LC/ESI/MS: The extrapolative dilution approach

Liquid chromatography electrospray mass spectrometry - LC/ESI/MS—a primary tool for analysis of low volatility compounds in difficult matrices - suffers from the matrix effects in the ESI ionization. It is well known that matrix effects can be reduced by sample dilution. However, the efficiency of simple sample dilution is often limited, in particular by the limit of detection of the method, and can strongly vary from sample to sample.In this study matrix effect is investigated as the function of dilution. It is demonstrated that in some cases dilution can eliminate matrix effect, but often it is just reduced. Based on these findings we propose a new quantitation method based on consecutive dilutions of the sample and extrapolation of the analyte content to the infinite dilution, i.e. to matrix-free solution.The method was validated for LC/ESI/MS analysis of five pesticides (methomyl, thiabendazole, aldicarb, imazalil, methiocarb) in five matrices (tomato, cucumber, apple, rye and garlic) at two concentration levels (0.5 and 5.0 mg kg⁻¹). Agreement between the analyzed and spiked concentrations was found for all samples. It was demonstrated that in terms of accuracy of the obtained results the proposed extrapolative dilution approach works distinctly better than simple sample dilution.The main use of this approach is envisaged for (a) method development/validation to determine the extent of matrix effects and the ways of overcoming them and (b) as a second step of analysis in the case of samples having analyte contents near the maximum residue limits (MRL).     

Quantitative transfer of polar analytes on a solid surface to a liquid matrix in MALDI profiling

In profiling of a specimen by matrix‐assisted laser desorption ionization (MALDI) using a solid matrix, the solvent of the matrix solution extracts an analyte(s). A quantitative profiling cannot be achieved if the solvent evaporates before the complete extraction of the analyte. The extraction can become more quantitative when a liquid matrix dissolved in a solvent is used, which remains a liquid even after the evaporation of the solvent. To check this, radii of an analyte circle (r_A), a matrix solution drop (r_D) and a liquid matrix (r_M) remaining after the solvent evaporation were controlled. Three types of samples were prepared, case A (r_A, r_D < r_M), case B (r_D ≤ r_M < r_A) and case C (r_M < r_D < r_A). In case A, the analyte amount in the matrix layer determined by MALDI was the same as the prepared amount inside the analyte circle. In case B, the analyte amount was the same as the amount inside the matrix circle. Only the analytes in contact with the liquid matrix layer, not more and not less, are transferred to the matrix layer. In case C, the analyte amount was greater than the amount inside the matrix circle, presumably because some of the analyte outside the matrix circle was dissolved by the solvent of the matrix solution. Copyright © 2016 John Wiley & Sons, Ltd.     

Co-NC as adsorbent and matrix providing the ability of MALDI MS to analyze volatile compounds

Traditional matrix does not allow matrix-assisted laser desorption/ionization mass spectrometry(MALDI MS) to analyze volatile compounds,because volatile analytes may vaporize during the sample preparation process or in the high vacuum circumstance of ion source.Herein,we reported a Co and N doped porous carbon material(Co-NC) which were synthesized by pyrolysis of a Schiff base coordination compound.Co-NC could simultaneously act as adsorbent of volatile compounds and as matrix of MALDI MS,to provide the capability of MALDI MS to analyze volatile compounds.As adsorbent,Co-NC could stro ngly adsorb and enrich the volatile compounds in perfume and herbs,and hold them even in the high vacuum circumstance.On the other hand,Co-NC could absorb the energy of the laser,and then transfer the energy to the analyte for desorption and ionization of analyte in both negative and positive ionization modes.Additionally,the background interferences were avoided in the low-mass region(<500 Da) when using Co-NC as matrix,overcoming the challenges of MALDI MS analysis of small molecule compounds.In summary,Co-NC as matrix tremendously extended the application of MALDI MS.     

Direct quantitative analysis of peptides using matrix assisted laser desorption ionization

The protocol and various matrices were examined for quantification of biomolecules in both the low ca. 1200 amu and mid mass 6000-12000 amu ranges using an internal standard. Comparative studies of different matrices of MALDI quantitative analysis showed that the best accuracy and standard curve linearity were obtained for two matrices: (a) 2,5-dihydroxybenzoic acid (DHB) combined with a comatrix of fucose and 5-methoxysalicylic acid (MSA) and (b) ferulic acid/fucose. In the low mass range, the quantitative limit was in the 30 fmol range and in the mid mass range the quantitative limit was in the 250 fmol range. Linear response was observed over 2-3 decades of analyte concentration. The relative error of the standard curve slope was 1.3-1.8% with correlation coefficients of 0.996-0.998.The main problem for quantitative measurement was suppression of the signal of the less concentrated component (analyte or internal standard) by the more concentrated component. The effect was identified with saturation of the matrix by the analyte. The threshold of matrix saturation was found to be in the range of 1/(3000-5000) analyte/matrix molar ratio. To avoid matrix saturation the (analyte+internal standard) to matrix molar ratio should be below this threshold. Thus the internal standard concentration should be as low as possible.DHB/MSA/fucose and ferulic acid/fucose matrices demonstrated good accuracy and linearity for standard curves even when the internal standard had chemical properties different from the analyte. However, use of an internal standard with different chemical properties requires highly stable instrumental parameters as well as constant (analyte+internal standard)/matrix molar ratio for all samples.     

Direct quantitative analysis of peptides using matrix assisted laser desorption ionization

The protocol and various matrices were examined for quantification of biomolecules in both the low ca. 1200 amu and mid mass 6000–12000 amu ranges using an internal standard. Comparative studies of different matrices of MALDI quantitative analysis showed that the best accuracy and standard curve linearity were obtained for two matrices: (a) 2,5-dihydroxybenzoic acid (DHB) combined with a comatrix of fucose and 5-methoxysalicylic acid (MSA) and (b) ferulic acid/fucose. In the low mass range, the quantitative limit was in the 30 fmol range and in the mid mass range the quantitative limit was in the 250 fmol range. Linear response was observed over 2–3 decades of analyte concentration. The relative error of the standard curve slope was 1.3–1.8% with correlation coefficients of 0.996–0.998.The main problem for quantitative measurement was suppression of the signal of the less concentrated component (analyte or internal standard) by the more concentrated component. The effect was identified with saturation of the matrix by the analyte. The threshold of matrix saturation was found to be in the range of 1/(3000–5000) analyte/matrix molar ratio. To avoid matrix saturation the (analyte+internal standard) to matrix molar ratio should be below this threshold. Thus the internal standard concentration should be as low as possible.DHB/MSA/fucose and ferulic acid/fucose matrices demonstrated good accuracy and linearity for standard curves even when the internal standard had chemical properties different from the analyte. However, use of an internal standard with different chemical properties requires highly stable instrumental parameters as well as constant (analyte+internal standard)/matrix molar ratio for all samples.     

Using calibration approaches to compensate for remaining matrix effects in quantitative liquid chromatography/electrospray ionization multistage mass spectrometric analysis of phytoestrogens in aqueous environmental samples

Signal suppression is a common problem in quantitative liquid chromatography/electrospray ionization multistage mass spectrometric (LC/ESI-MS(n)) analysis in environment samples, especially in highly loaded wastewater samples with highly complex matrix. Optimization of sample preparation and improvement of chromatographic separation are prerequisite to improve reproducibility and selectivity. Matrix components are reduced if not eliminated by optimization of sample preparation steps. However, extensive sample preparation may be time-consuming and risk the significant loss of some trace analytes. The best way to further compensate matrix effects is the use of an internal standard for each analyte. However, in a multi-component analysis, finding appropriate internal standards for every analyte is often difficult. In this present study, a more practical alternative option was sought. Matrix effects were assessed using the post-extraction addition method. By comparison of three different calibration approaches, it was found that matrix-matched calibration combined with one internal standard provides a satisfactory method for compensating for any residual matrix effects on all the analytes. Validating experiments on different sewage treatment plant (STP) influent samples analyzing for a range of phytoestrogens showed that this calibration method provided satisfactory results with concentration ratio 96.1-105.7% compared to those by standard addition.     

Isoliquiritigenin (4,2′,4′-trihydroxychalcone): A new matrix-assisted laser desorption/ionization matrix with outstanding properties for the analysis of neutral oligosaccharides

A novel matrix of isoliquiritigenin (ISL), a flavonoid with a chalcone structure (4,2′,4′-trihydroxychalcone), was demonstrated to be advantageous in the analysis of neutral oligosaccharides by matrix-assisted laser desorption/ionization time-of-flight mass spectrometry (MALDI-TOF MS). With ISL as a matrix, adequate signal for an analyte can be obtained in much lower matrix concentrations and laser intensity compared to commonly used MALDI matrices. Four different sample preparation methods were tested, and the dried droplet method exhibited the best performance on MALDI-TOF-MS analysis of oligosaccharides with ISL as a matrix. For the analysis of carbohydrates, compared with popular matrices such as 2,5-dihydroxybenzoic acid (DHB) and 2,4,6-trihydroxyacetophenone (THAP), ISL exhibited outstanding matrix properties as follows: (1) higher homogeneity of crystallization thus allowing automatic data acquisition, (2) better spectral quality in terms of resolution and signal to noise ratio (S N⁻¹), (3) better salt tolerance, (4) higher sensitivity, and (5) enough fragmentation yield to use LIFT-TOF/TOF MS to get richer structural information. In addition, reliable quantitative analysis of oligosaccharides with a good linearity over two concentration orders (1–100 pmol μL⁻¹) and good reproducibility of the signal intensity (RSD less than 15%) were achieved using this matrix. These results give a new outlook on high-speed analysis of neutral carbohydrates by MALDI-TOF MS.     

Isotope tag method for quantitative analysis of carbohydrates by liquid chromatography-mass spectrometry

We have previously demonstrated that liquid chromatography/mass spectrometry equipped with a graphitized carbon column (GCC-LC/MS) is useful for the structural analysis of carbohydrates in a glycoprotein. Here, we studied the monosaccharide composition analysis and quantitative oligosaccharide profiling by GCC-LC/MS. Monosaccharides were labeled with 2-aminopyridine and then separated and monitored by GCC-LC/MS in the selective ion mode. The use of tetradeuterium-labeled pyridylamino (d4-PA) monosaccharides as internal standards, which were prepared by the tagging of standard monosaccharides with hexadeuterium-labeled 2-aminopyridine (d6-AP), afforded a good linearity and reproducibility in ESIMS analysis. This method was successfully applied to the monosaccharide composition analysis of model glycoproteins, fetuin, and erythropoietin. For quantitative oligosaccharide profiling, oligosaccharides released from an analyte and a standard glycoprotein were tagged with d0- and d6-AP, respectively, and an equal amount of d0- and d4-PA oligosaccharides were coinjected into GCC-LC/MS. In this procedure, the oligosaccharides that existed in either analyte or a standard glycoprotein appeared as single ions, and the oligosaccharides that existed in both analyte and a standard glycoprotein were detected as paired ions. The relative amount of analyte oligosaccharides could be determined on the basis of the analyte/internal standard ion-pair intensity ratio. The quantitative oligosaccharide profiling enabled us to make a quantitative and qualitative comparison of glycosylation between the analyte and standard glycoproteins. The isotope tag method can be applicable for quality control and comparability assessment of glycoprotein products as well as the analysis of glycan alteration in some diseases.     

The development and assessment of high‐throughput mass spectrometry‐based methods for the quantification of a nanoparticle drug delivery agent in cellular lysate

The safe use of lipid‐based drug delivery agents requires fast and sensitive qualitative and quantitative assessment of their cellular interactions. Many mass spectrometry (MS) based analytical platforms can achieve such task with varying capabilities. Therefore, four novel high‐throughput MS‐based quantitative methods were evaluated for the analysis of a small organic gene delivery agent: N,N‐bis(dimethylhexadecyl)‐1,3‐propane‐diammonium dibromide (G16‐3). Analysis utilized MS instruments that detect analytes using low‐resolution tandem MS (MS/MS) analysis (i.e. QTRAP or linear ion trap in this work) or high‐resolution MS analysis (i.e. time of flight (ToF) or Orbitrap). Our results indicate that the validated fast chromatography (FC)‐QTRAP‐MS/MS, FC‐ LTQ‐Orbitrap‐MS, desorption electrospray ionization‐collision‐induced dissociation (CID)‐MS/MS and matrix assisted laser desorption ionization‐ToF/ToF‐MS MS methods were superior in the area of method development and sample analysis time to a previously developed liquid chromatography (LC)‐CID‐MS/MS. To our knowledge, this is the first evaluation of the abilities of five MS‐based quantitative methods that target a single pharmaceutical analyte. Our findings indicate that, in comparison to conventional LC‐CID‐MS/MS, the new MS‐based methods resulted in a (1) substantial reduction in the analysis time, (2) reduction in the time required for method development and (3) production of either superior or comparable quantitative data. The four new high‐throughput MS methods, therefore, were faster, more efficient and less expensive than a conventional LC‐CID‐MS/MS for the quantification of the G16‐3 analyte within tissue culture. When applied to cellular lysate, no significant change in the concentration of G16‐3 gemini surfactant within PAM212 cells was observed between 5 and 53 h, suggesting the absence of any metabolism/excretion from PAM212 cells. Copyright © 2014 John Wiley & Sons, Ltd.     

Supported liquid extraction in combination with LC‐MS/MS for high‐throughput quantitative analysis of hydrocortisone in mouse serum

A high‐throughput LC–MS/MS bioanalytical method was developed and validated for the determination of hydrocortisone in mouse serum via supported liquid extraction (SLE) in a 96‐well plate format. Although sample extracts from SLE result in similar matrix effects compared with conventional liquid–liquid extraction (LLE), greater analyte extraction recovery and much higher analysis throughput for the quantitative analysis of hydrocortisone in mouse serum were obtained. The current LC‐MS/MS method was validated for a concentration range of 2.00–2000 ng/mL for hydrocortisone using a 0.100 mL volume of mouse serum. The intra‐ and inter‐day precision and accuracy of the quality control samples at low, medium and high concentration levels showed ≤12.9% CV and ?3.4–6.2% bias for the analyte in mouse serum. Copyright © 2009 John Wiley & Sons, Ltd.     

Trace LC/MS quantitative analysis of polypeptide biomarkers: impact of 1-D and 2-D chromatography on matrix effects and sensitivity

We investigated the impact of one dimension (single reverse phase (RP) column) and two dimension (two different RP columns) chromatographic methods on SIM (MS) and multiple reaction monitoring (MRM; MS/MS) performance from human plasma. We find that MRM analysis is clearly preferable for 1-D applications; however, implementation of SIM detection in conjunction with 2-D separation technique resulted in an over 60-fold increase in analyte peak area and improved S/N compared to MRM for our analyte, human C-peptide. Implementation of a 2-D RP-RP technique with SIM detection is capable of eliminating matrix effects and greatly increases signal response and data quality. For two large peptides in complex biological samples, we found that a 2-D approach performed better than high quality sample preparation together with 1-D chromatography and MRM, even on a high-end mass spectrometer.     

The potential for clinical applications using a new ionization method combined with ion mobility spectrometry-mass spectrometry

Recently discovered ionization methods for use in mass spectrometry (MS), are widely applicable to biological materials, robust, and easy to automate. Among these, matrix assisted ionization vacuum (MAIV) is astonishing in that ionization of low and high-mass compounds are converted to gas-phase ions with charge states similar to electrospray ionization simply by exposing a matrix:analyte mixture to the vacuum of a mass spectrometer. Using the matrix compound, 3-nitrobenzonitrile, abundant ions are produced at room temperature without the need of high voltage or a laser. Here we discuss chemical analyses advances using MAIV combined with ion mobility spectrometry (IMS) real time separation, high resolution MS, and mass selected and non-mass selected MS/MS providing rapid analyte characterization. Drugs, their metabolites, lipids, peptides, and proteins can be ionized simultaneously from a variety of different biological matrixes such as urine, plasma, whole blood, and tissue. These complex mixtures are best characterized using a separation step, which is obtained nearly instantaneously with IMS, and together with direct ionization and MS or MS/MS provides a fast analysis method that has considerable potential for non-targeted clinical analyses.     

Quantitative analyses of fullerene and polycyclic aromatic hydrocarbon mixtures via solvent‐free matrix‐assisted laser desorption/ionization mass spectrometry

We explore the feasibility of reliable quantitative matrix‐assisted laser desorption/ionization mass spectrometry (MALDI‐MS) analyses via solvent‐free sample preparation, as this procedure provides the unique convenience of being applicable also to insoluble samples. As quantitative MALDI measurements are even more complicated for species ionized by cation attachment, we investigated model systems, such as polycyclic aromatic hydrocarbons (PAHs) and fullerenes, which undergo photoionization and do not require additional cationizing salts. Our quantitative approach rests upon applying the standard‐addition method in MALDI for the quantitative characterization of binary mixtures. Two different systems are tested. Set 1 is composed of hexakis(dodecyl)hexabenzocoronene and hexakis(dodecyl)hexaphenylbenzene, which represent the product and precursor of a cyclodehydrogenation reaction, and Set 2 is a mixture of C60 and C70 fullerenes. In Set 1, severe anomalies could be detected due to a strong influence of the matrix/analyte ratio on the correlation between signal intensity and analyte amount. This can be related to the strong intermolecular interactions among the hexabenzocoronene (HBC) aromatic cores hampering the desorption step and to intermolecular charge transfers, which influence the ionization probability. Minor interferences to the quantitative MALDI characterization are encountered in the analysis of C60 and C70 fullerenes. The spherical shapes of C60 and C70 buckyballs prevent strong aggregation. Thus, no molecule‐dependent anomalies in their desorption‐photoionization behaviour are recognized. Copyright © 2008 John Wiley & Sons, Ltd.