Synergistic effect between hydrophobic oxide nanoparticles and ammonium polyphosphate on fire properties of poly(methyl methacrylate) and polystyrene

Synergism on fire properties has been investigated between nano-sized hydrophobic oxides (alumina and silica) and ammonium polyphosphate (AP) flame-retardant additive. Thermal degradation of mixed additives (50% w/w) showed the impact of oxides on AP degradation. The effect of modified nanoparticles was compared with corresponding hydrophilic oxide as regards thermal and fire behaviour. The nanocomposites prepared by melt-blending were evaluated by thermogravimetric analysis and cone calorimetry measurements. Residues were characterized by ATR-FTIR spectroscopy, X-ray diffraction and SEM-EDX experiments. A noteworthy decrease of peak of heat release rate and smoke opacity as well as an increase of LOI were noticed with hydrophobic silica combined with AP both in PMMA and PS. This flame-retardant behaviour was ascribed mainly to the formation of a specific silicon metaphosphate (SiP₂O₇) crystalline phase which contributes to promote charring and an efficient insulating layer.     

Hydrophilic–hydrophobic AB diblock copolymers containing poly(trimethylene carbonate) and poly(ethylene oxide) blocks

AB‐type block copolymers with poly(trimethylene carbonate) [poly(TMC); A] and poly(ethylene oxide) [PEO; B; number‐average molecular weight (M_n) = 5000] blocks [poly(TMC)‐b‐PEO] were synthesized via the ring‐opening polymerization of trimethylene carbonate (TMC) in the presence of monohydroxy PEO with stannous octoate as a catalyst. M_n of the resulting copolymers increased with increasing TMC content in the feed at a constant molar ratio of the monomer to the catalyst (monomer/catalyst = 125). The thermal properties of the AB diblock copolymers were investigated with differential scanning calorimetry. The melting temperature of the PEO blocks was lower than that of the homopolymer, and the crystallinity of the PEO block decreased as the length of the poly(TMC) blocks increased. The glass‐transition temperature of the poly(TMC) blocks was dependent on the diblock copolymer composition upon first heating. The static contact angle decreased sharply with increasing PEO content in the diblock copolymers. Compared with poly(TMC), poly(TMC)‐b‐PEO had a higher Young's modulus and lower elongation at break. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 4819–4827, 2005     

Surface characterization of functional poly(diacetylene) and poly(butadiene) mono- and multilayers

The surface properties of Langmuir-Blodgett mono- and multilayers of a variety of amphiphilic poly(diacetylene)s and poly(butadiene)s were investigated by contact angle, streaming potential, ellipsometry, and X-ray photoelectron spectroscopic (XPS) measurements. Captive air and octane angles varied between approximately 60° and 105° for hydrophobicx-layers and 31° to 46° for hydrophilic surfaces depending on the particular head group, whereas advancing angles determined via the vertical plate method are considerably higher. Negative streaming potentials were obtained for all surfaces. Positively charged monolayers yielded less negative- potential values (–28 mV) than negatively charged (–52 mV) or hydrophobic (–50 mV) layers. Ellipsometry measurements yielded an average layer thickness of 27±6 Å for 3 to 11 layers. X-ray photoelectron spectroscopy results qualitatively confirmed the expected composition. All of the samples, which were handled and stored in air after deposition and polymerization, were surface oxidized.Dedicated to Prof. Dr. F. H. Müller.     

Synthesis and characterization of polystyrene–poly(ethylene oxide)–heparin block copolymers

A procedure for the preparation of new block copolymers composed of a hydrophobic block of polystyrene, a hydrophilic spacer-block of poly(ethylene oxide) and a bioactive block of heparin was investigated. Polystyrene with one amino group per chain was synthesized by free radical oligomerization of styrene in dimethylformamide, using 2-aminoethanethiol as a chain transfer agent. This amino group was used in the coupling reaction with amino-telechelic poly(ethylene oxide) to produce an AB type diblock copolymer with one amino group per polystyrene (PSt)–poly(ethylene oxide) (PEO) chain. The amino-semitelechelic oligo-styrene was converted into the isocyanate-semitelechelic oligo-styrene using toluene 2,4-diisocyanate and subsequent coupling with H₂N–PEO–NH₂ afforded AB type block copolymers with terminal amino groups. The coupling of PSt–PEO–NH₂ with heparin was performed in a DMF–H₂O mixture, first by activating the heparin carboxylic groups with EDC at pH 5.1–5.2 and subsequently reacting the activated carboxylic groups with the amino groups of the PSt–PEO–NH₂ at pH 7.5. Depending on the molecular weights of the diblock copolymer used 25–29% w/w heparin was incorporated. These polymers will be further evaluated for their blood-compatibility.     

Syntheses and characterizations of poly[2‐(dimethylamino)ethyl methacrylate]–poly(propylene oxide)–poly[2‐(dimethylamino)ethyl methacrylate] ABA triblock copolymers

A novel, near‐monodisperse, well‐defined ABA triblock copolymer, poly[2‐(dimethylamino)ethyl methacrylate]‐b‐poly(propylene oxide)‐b‐poly[2‐(dimethylamino)ethyl methacrylate], was synthesized via oxyanion‐initiated polymerization. The initiator was a telechelic‐type potassium alcoholate prepared from poly(propylene glycol) and KH in dry tetrahydrofuran. The copolymers produced were characterized by Fourier transform infrared, ¹H NMR, and gel permeation chromatography (GPC). GPC and ¹H NMR analyses showed that the products obtained were the desired copolymers, with narrow molecular weight distributions (ca. 1.09–1.11) very close to that of the original poly(propylene glycol). ¹H NMR, surface tension measurements, and dynamic light scattering all indicated that the triblock copolymer led to interesting aqueous solution behaviors, including temperature‐induced micellization and very high surface activity. © 2002 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 40: 624–631, 2002; DOI 10.1002/pola.10144     

Synthesis and block‐specific complexation of poly(ethylene oxide)–poly(tetrahydrofuran)–poly(ethylene oxide) triblock copolymers

Well‐defined ABA triblock copolymers in which A stands for poly(ethylene oxide) (PEO) and B for poly(tetrahydrofuran) (PTHF) were synthesized by end‐capping bifunctionally living PTHF with different polyethylene glycol–monomethylethers. Differential scanning calorimetry analysis of these copolymers showed two melting points: one around 55 °C due to the PEO blocks, and one around 30 °C due to the PTHF segments, demonstrating that these block copolymers show extensive phase separation. Upon addition of sodium thiocyanate, crystalline complexes with PEO were formed and as a consequence, the melting points of the PEO segments had shifted to approximately 170 °C, whereas the melting points of the PTHF segments decreased slightly. The obtained materials behave as thermoplastic elastomers up to 160–175 °C. The influence of the relative lengths of the PEO and the PTHF segments on the thermal and mechanical properties of the materials have been investigated. Copyright © 1999 John Wiley & Sons, Ltd.     

Photolysis of poly(ethyl acrylate) and poly(n–butyl acrylate) in vacuo

Thin films of poly(ethyl acrylate) and poly(n-butyl acrylate) were decomposed in vacuo by means of a high pressure Hg lamp, and the rate of development of volatile products was measured. The main gaseous products were CO, CO₂, and the alcohol, aldehyde, alkane, and formate derived from the respective ester groups. In addition poly(ethyl acrylate) evolved acetal as well as ethyl propionate, while n-butyl valerate was evolved from poly(n-butyl acrylate) only after prolonged exposure. All products and the principal features of the decomposition are discussed.     

Surface characterization of poly(2,2,3,3,3-pentafluoropropyl methacrylate) by inverse gas chromatography and contact angle measurements

A fluorinated methacrylic homopolymer, poly(2,2,3,3,3-pentafluoropropyl methacrylate) (PPFPMA) was synthesized by a free radical polymerization reaction. The dispersive component of the surface energy () of PPFPMA was determined by contact angle measurements and inverse gas chromatography (IGC). An extensive surface characterization was conducted by means of IGC. Surface characterization demonstrated that PPFPMA has low value, even at 35 °C and is a Lewis amphoteric polymer with predominantly basic character, as confirmed by the Lewis acidity and basicity constants K_A and K_B, respectively. The values of obtained by IGC are slightly higher than those obtained by the contact angle method. This trend can be attributed to the fact that IGC evaluates, primarily, high energy sites of a surface.     

Comprehensive study on reinforcement of poly(vinyl chloride) nanocomposite films with ZnO nanoparticles modified by citric acid and vitamin C

We reported a general facile approach for modifying NPs and incorporating them into PVC polymer via ultrasonic irradiation. ZnO nanoparticles (NP)s modified with ascorbic acid (AS) and citric acid (CA) were employed to investigate the agglomeration behavior under poly(vinyl chloride) PVC matrix. To compare and determine the suitable construction, the prepared PVC/ZnO-CA-AS NCs (4, 8, 12?wt%) were characterized. UV-visible measurements indicate, increasing absorption value results in an increase of ZnO content. According to the obtained information from the TGA of the NCs, further increases in modified ZnO results in an increase in flame-retardancy. The mechanical properties investigation revealed improvement of the elongation at maximum stress.     

Inverse gas chromatographic characterization of triblock copolymer of polystyrene–poly(ethylene oxide)–polystyrene

The thermodynamic properties of triblock copolymer of polystyrene–poly (ethylene oxide)–polystyrene (PS‐b‐PEO‐b‐PS) were investigated by means of inverse gas chromatography (IGC) using 15 different kinds of solvents as the probes. Some thermodynamic parameters, such as specific retention volume, molar heats of sorption, weight fraction activity coefficient, Flory‐Huggins interaction parameter, partial molar heats of mixing and solubility parameter were obtained to judge the interactions between PS‐b‐PEO‐b‐PS polymers and solvents and the solubility of the polymers in these solvents. It was found that increasing PEO content in PS‐b‐PEO‐b‐PS resulted in the increase in the solubility of PS‐b‐PEO‐b‐PS in alkanes and acetates solvents, but the solubility in alcohols had no change, and more PEO content in polymer caused a small decrease in the solubility parameter of PS‐b‐PEO‐b‐PS polymer, © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 2015–2022, 2007     

Synthesis and self‐assembly of highly incompatible polybutadiene–poly(hexafluoropropylene oxide) diblock copolymers

A versatile coupling reaction for the preparation of polybutadiene–poly‐(hexafluoropropylene oxide) (BF) diblock copolymers is described. Six diblock copolymers with different block lengths were characterized by nuclear magnetic resonance spectroscopy and size exclusion chromatography; all six had total molecular weights below 15,000. Microphase separation of the block copolymers in the bulk state was established by small‐angle X‐ray scattering (SAXS) and differential scanning calorimetry. SAXS data suggest that the diblocks are characterized by an unusually large Flory‐Huggins interaction parameter, χ, on the order of 10. However, extraction of χ from the order–disorder transition gave large (order 1) but significantly different values, thereby suggesting that these copolymers are too small and too strongly interacting to be described by block copolymer mean‐field theory. Dynamic light scattering was used to analyze dilute solutions of the title block copolymers in four selective organic solvents; the sizes of the micelles formed were solvent dependent. The micellar aggregates were large and nonspherical, and this is also attributed to the high degree of incompatibility between the two immiscible blocks. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 3685–3694, 2005     

Poly(vinyl chloride)–poly(ethylene oxide) block copolymers: Synthesis and characterization

Poly(vinyl chloride)-poly(ethylene oxide) block copolymers have been synthesized in solution and emulsion. The polymers were made by first synthesizing macroazonitriles through the reaction of 4,4′-azobis-4-cyanovleryl chloride with hydroxy-terminated poly(ethylene oxide) of varying molecular weights. These macroazonitriles had molecular weights in the range of 3000–88,000 and degrees of polymerization from 5 to 24. Thermal decomposition of the azolinkages in the presence of vinyl chloride monomer yielded block copolymers containing form 2 to 20 wt % poly(ethylene oxide). The structures of the block copolymers were characterized by spectrometric, elemental and molecular weight analyses. The possibility of some graft polymerization occurring via free-radical extraction of a methylene hydrogen from the poly(ethylene oxide) was considered. Polymerization of vinyl chloride with an azonitrile initiator in the presence of a poly(ethylene oxide) yielded predominately homopolymer with some grafted poly(vinyl chloride).     

Synthesis and characterization of PAni–SiO2 and PTh–SiO2 nanocomposites' thin films by plasma polymerization

In the present work, we explore the possibility to deposit polyaniline–silicon dioxide (PAni–SiO₂) and polythiophene–silicon dioxide (PTh–SiO₂) nanocomposites through a plasma polymerization route. The films were generated by spraying of mixtures of nano-sized silica particles dispersed in the liquid monomer into a plasma stream of the DC-plasma discharge reactor. The silica in the resulted polymer matrix changes the conduction mechanisms varying from ohmic to ballistic and traps inducing the space charged limited currents (SCLC). The silica modifies the morphology and composition of the deposited films.     

Fabrication and characterization of magnesium—ion-conducting flexible polymer electrolyte membranes based on a nanocomposite of poly(ethylene oxide) and potato starch nanocrystals

Journal of Solid State Electrochemistry - Flexible and free-standing electrolyte membranes of nanocomposite ‘poly(ethylene oxide) (PEO)/starch-nanocrystals (SNCs)’ complexed with...     

Removal of iron (III) oxide particles from a quartz plate by liquid flow

The detachment of submicron particles of iron (III) oxide from a quartz plate in aqueous solutions was investigated by using a well-defined flow of electro-osmosis in comparison with the ordinary flow of water without electrokinetic effect. A rectangular quartz cell was used for removal experiments. Zeta potentials of the particles and the plate were determined by electrophoresis and electro-osmosis, respectively. When the iron (III) oxide particles adhering to the quartz plate were removed by the electro-osmotic flow or the ordinary (Poiseuille) flow, the removal efficiency increased with increasing hydrodynamic force. The removal efficiency by electro-osmotic flow was almost the same as that by ordinary flow under the condition of the same magnitude of applied hydrodynamic force. The values of volume flow rate for the removal efficiency of 0.5 for the electro-osmotic flow was extremely small compared with that for the ordinary flow, showing the effectiveness of particle removal by electrokinetic effect of electro-osmosis. The kinetic analysis of the particle removal process showed that it was characterized by two different rate constants, the rate constant of the rapid process and that of the slow process. The rate constant of slow process increased with increasing electro-osmotic velocity. This shows that the electro-osmotic flow acts as a mechanical force to overcome the energy barrier in the removal process. The rate constant increased with increasing surfactant concentration and this trend became more noticeable as electro-osmotic velocity increased. It is concluded from this result that the effect of surfactant on particle removal is enhanced by the mechanical force in removal processes.     

Surface characterization and liquid crystal alignment behavior of comb-like poly(oxyethylene)/poly(3-hexylthiophene) blend films

The blend surfaces of poly[oxy(n-decylsulfonylmethyl)ethylene] (CH(3)-10SE) and poly (3-hexylthiophene) (P3HT) with different weight ratios were prepared by spin coating the polymer solution mixtures. In this study, their surface properties such as surface morphology, chemical composition, molecular structure, and wettability were systematically studied and correlated with liquid crystal (LC) alignment behaviors on the blend films. Therefore, we found that CH(3)-10SE part with a well-ordered side chain structure predominantly affects the both of wettability and LC alignment behavior of the blend films while there was no clear association between the wettability and the LC alignment behavior.     

Chitosan–magnetite nanocomposites (CMNs) as magnetic carrier particles for removal of Fe(III) from aqueous solutions

This research focuses on removal of Fe(III) from aqueous solution using chitosan–magnetite nanocomposites as potential sorbent. The presence of nanosized magnetic particles within the nanocomposites was confirmed by TEM and SAED analysis. The particles with diameter 508 μm and 84 μm, follow Frendlich sorption isotherm at 30 °C, and the Frendlich constants (K_F, 1/n) have been found to be 5.974 mg g⁻¹, 2.66 and 35.98 mg g⁻¹, 1.385, respectively. Out of various kinetic models, the experimental data for dynamic uptake of Fe(III) is best fitted on ‘pseudo-second order’ kinetic model. The linear nature of plots between log (% sorption) and log (time) is indicative of intra-particle diffusion. For the particles with diameters 508 μm and 84 μm, the value of k_id was found to be 1.78 mg l⁻¹ min^−0.5 and 2.13 mg l⁻¹ min^−0.5. The sorption mean free energy from the Dubinin–Radushkevic isotherm was found to be 7.04 kJ mol⁻¹ indicating chemical nature of sorption. The increase in chitosan content in sorbent particles is found to enhance the Fe(III) uptake. The various thermodynamic parameters have also been evaluated. Finally, the presence of Cu²⁺ ions in the sorbate is found to decrease the uptake of Fe(III).