Si-W/Si/SiO2/Si(100)的横截面电子显微镜研究

本文用横截面电子显微镜法分析了Si-W/Si/SiO₂/Si(100)在440—1000℃退火后的晶化过程,以及各个界面的变化情况.发现Si-W合金膜中,WSi₂并未优先在表面、界面处形成晶核.当退火温度不高于700℃时,反应在合金膜内发生,表面、界面起伏和缓.退火温度高达800—1000℃时,界面、表面出现原子扩散,造成剧烈的界面起伏;表面则出现小的热沟槽,Si/SiO₂界面也出现高分辨电子显微镜才能观察到的起伏.表面、界面的原子迁移的动力来源于晶界与表面、界面张力.由于SiO₂中Si—O键很稳定,不易发生Si和O在界面处的互扩散,所以Si/SiO₂界面起伏很小. 关键词：     

2018年2期电子期刊

光诱导功能退化是胶体量子点在应用中面临的主要挑战之一,本文针对这一问题研究了使用磁控溅射沉积SiO₂薄膜形成钝化层来提高CdSe/ZnS量子点发光稳定性的方法。首先,通过三正辛基膦辅助连续离子层吸附反应方法合成了615 nm发光的红色CdSe/ZnS量子点。然后将量子点旋涂在SiO₂/Si基片上,再通过磁控溅射方法在量子点上沉积了厚度为20 nm的SiO₂薄膜作为钝化层。使用连续波激光光源分别在空气气氛和真空条件下照射样品,研究了经过不同照射时间后钝化和未钝化量子点的稳态光致发光光谱。结果表明,随着照射时间的延长,没有SiO₂钝化的量子点的PL强度显著降低、PL峰值发生蓝移、FWHM不断增大。对比研究发现,由于SiO₂薄膜能够阻挡空气中的水和氧,减缓了量子点表面的光诱导氧化现象,因此显著提高了CdSe/ZnS量子点的稳定性。     

高速率沉积磁控溅射技术制备Ge点的退火生长研究

采用磁控溅射技术在Si衬底上以350?C沉积14 nm的非晶Ge薄膜,通过退火改变系统生长热能,实现了低维Ge/Si点的生长.利用原子力显微镜(AFM)和拉曼(Raman)光谱所获得的形貌和声子振动信息,对Ge点的形成机理和演变规律进行了研究.实验结果表明:在675?C退火30 min后,非晶Ge薄膜转变为密度高达8.5×109cm-2的Ge点.通过Ostwald熟化理论、表面扩散模型和对激活能的计算,很好地解释了退火过程中,Ge原子在Si表面迁移、最终形成纳米点的行为.研究结果表明用高速沉积磁控溅射配合热退火制备Ge/Si纳米点的方法,可为自组织量子点生长实验提供一定的理论支撑.     

Si(111)-(7×7)表面上Ge量子点的自组织生长

用扫描隧道显微镜研究了Si(111)(7×7)表面上Ge量子点的自组织生长.室温下用固相外延法在硅基底上沉积亚单层的Ge,然后在适当的温度下退火可以聚集形成有序的Ge量子点.由于Ge在Si(111)(7×7)表面选择性的吸附而形成有序的Ge量子点. 关键词： 锗 硅 扫描隧道显微镜 自组织生长     

离子束溅射自组装Ge/Si量子点生长的演变

采用离子束溅射技术,通过改变Ge的沉积量,在n型Si(100)衬底上自组装生长了一系列Ge量子点样品. 利用AFM和Raman光谱对样品表面形貌和结构进行表征,系统地研究了Ge量子点形貌、密度、尺寸大小以及Ge的结晶性和量子点中组分等随Ge沉积量的演变规律. 结果表明:Ge层从二维薄层向三维岛过渡过程中,没有观察到传统的由金字塔形向圆顶形量子点过渡,而是直接呈圆顶形生长;且随着Ge沉积量的增加,量子点密度先增大后减小,Ge的结晶性增强同时Ge/Si互混加剧,量子点中Si的组分增加. 关键词： 离子束溅射 量子点 表面形貌 Raman光谱     

氧化硅层厚度对Si/SiO2界面电子态结构与光学性质的影响

在氧化硅上生长纳米硅晶,保持氧化硅的直接带隙结构,降低其能带带隙,以用于发光和光伏。采用基于密度泛函理论的第一性原理研究了块体α-方石英、薄膜α-方石英、Si/SiO₂界面的电子态结构和Si/SiO₂界面的光学性质。结果显示,其均为直接带隙半导体,当薄膜α-方石英厚度和Si/SiO₂界面氧化硅层厚度逐渐减小时,能带带隙均逐渐变大,表现出明显的量子限制效应。光学性质计算结果表明：Si/SiO₂界面虚部介电峰和吸收峰的峰值随氧化硅层厚度降低而显著升高,且峰位向高能量方向蓝移。使用脉冲激光沉积制备了氧化硅上硅晶薄膜,测量了Si/SiO₂界面样品的PL光谱,在670 nm处存在一个强的发光峰,在波长超过830 nm后,Si/SiO₂界面样品的发光强度不断升高。因此,可以通过控制Si/SiO₂界面氧化硅层厚度有效地调控Si/SiO₂界面的电子态结构和光学性质,引进边缘电子态,调控其带隙进入1～2 eV区间,获取硅基发光材料...     

Sr/Si(100)表面TiSi2纳米岛的扫描隧道显微镜研究

为了解半导体衬底与氧化物之间存在的相互作用,以及量子尺寸效应对不同再构体的影响,制备了1—2个原子层厚的TiSi₂/Si(100)纳米岛,并使用扫描隧道显微镜(STM)表征手段详细地研究了TiSi₂ /Si(100)纳米岛的电子和几何特性. 结果发现:这些纳米岛表面显示出明显的金属性;其空态STM图像具有典型的偏压依赖性:在高偏压下STM 图像由三聚物形成的单胞构成,并在低偏压下STM 图像显示为密堆积的图案,这些不同的图案反映出不同能量位的态密度有明显差异. 关键词： 2纳米岛')" href="#">TiSi₂纳米岛 Sr/Si(100)表面 扫描隧道显微镜     

Au/SiO2纳米复合薄膜的微结构及光吸收特性研究

用多靶磁控溅射技术制备了Au/SiO₂纳米多层薄膜.利用透射电子显微镜以及吸 收光谱对Au/SiO₂复合薄膜的微观结构、表面形貌及光学性能进行了表征和测试 .研究结果表明：单层Au/SiO₂薄膜中Au沉积时间小于10s时，分散在SiO_{2< /sub>中的Au颗粒随Au的沉积时间的延长而增大；当沉积时间超过10s后，Au颗粒的尺寸几乎 不随沉积时间变化，但Au颗粒的形状由网络状结构变为薄膜状结构.［Au(t1关键词： 尺寸效应 纳米复合薄膜 吸收光谱 有效媒质理论}     

离子注入Zn的Si(001)基片热氧化制备纳米ZnO团簇及其生长行为研究

采用离子注入技术将Zn离子注入Si（001）基片,并在大气环境下加热氧化制备了ZnO纳米团簇.利用电子探针、薄膜X射线衍射仪、原子力显微镜和透射电子显微镜,对注入和热氧化后的薄膜成分、表面形貌和微观结构进行表征,探讨了热氧化温度以及注入剂量对纳米ZnO团簇的成核过程及生长行为的影响.结果表明,Zn离子注入到Si基片表面后形成了Zn纳米团簇,热氧化过程中Zn离子向表面扩散,在表面SiO₂非晶层和Si基片多晶区的界面处形成纳米团簇.热氧化温度是影响ZnO纳米团簇结晶质量的一个重要参数.随着热氧化温度的升高,金属Zn的衍射峰强度逐渐变弱并消失,而ZnO的（101）衍射峰强度逐渐增强.当热氧化温度高于800 ℃以后,ZnO与SiO₂之间开始发生化学反应形成Zn₂SiO₄. 关键词： ZnO纳米团簇 离子注入 微观结构 形貌分析     

4H-SiC纳米薄膜的微结构及其光电性质研究

采用新设计的电极结构的等离子体增强化学气相沉积(PECVD)技术,在高功率密度、高氢稀释比、低温、偏压及低反应气压的条件下,在衬底表面形成双等离子流,增加了衬底表面SiC的成核概率,增强成核作用,形成纳米晶.采用高H2等离子体刻蚀弱的、扭曲的、非晶Si—C及Si—Si和Si—H等键时,由于H等离子体对纳米SiC晶粒与非晶态键的差异刻蚀作用,产生自组织生长,发生晶化.Raman光谱和透射电子衍射(TEM)的测试结果表明,纳米晶SiC是4HSiC多型结构.电子显微照片表明平均粒径为16nm,形状为微柱体.实验结果指出,SiC纳米晶的形成必须经过偏压预处理成核,并且其晶化存在一个功率密度阈值;当低于这一功率密度阈值时,晶化消失;当超过这一阈值时,纳米晶含量随功率密度的提高而增加.随着晶化作用的加强,电导率增加. 关键词： 4H-SiC PECVD 纳米结构 多型薄膜 纳米电子学     

Photoluminescence and optical absorption properties of silicon quantum dots embedded in Si-rich silicon nitride matrices

Silicon nitride (SiN_x) films were prepared with a gas mixture of SiH₄ and NH₃ on Si wafers using the plasma-enhanced chemical vapor deposition (PECVD) method. High-resolution transmission electron microscopy and infrared absorption have been used to reveal the existence of the Si quantum dots (Si QDs) and to determine the chemical composition of the silicon nitride layers. The optical properties of these structures were studied by photoluminescence (PL) spectroscopy and indicate that emission mechanisms are dominated by confined excitons within Si QDs. The peak position of PL could be controlled in the wavelength range from 1.5 to 2.2 eV by adjusting the flow rates of ammonia and silane gases. Absorbance spectra obtained in the transmission mode reveal optical absorption from Si QDs, which is in good correlation with PL properties. These results have implications for future nanomaterial deposition controlling and device applications.     

Correlation between optical properties and Si nanocrystal formation of Si-rich Si oxide films prepared by plasma-enhanced chemical vapor deposition

We have investigated the phase separation and silicon nanocrystal (Si NC) formation in correlation with the optical properties of Si suboxide (SiO_x, 0 < x < 2) films by thermal annealing in high vacuum. The SiO_x films were deposited by plasma-enhanced chemical vapor deposition at different nitrous oxide/silane (N₂O/SiH₄) flow ratios. The as-deposited films show increased Si concentration with decreasing N₂O/SiH₄ flow ratio, while the deposition rate and surface roughness have strong correlations with the flow ratio in the N₂O/SiH₄ reaction. After thermal annealing at temperatures above 1000 °C, Fourier transform infrared spectroscopy, Raman spectroscopy, and transmission electron microscopy manifest the progressive phase separation and continuous growth of crystalline-Si (c-Si) NCs in the SiO_x films with increasing annealing temperature. We observe a transition from multiple-peak to single peak of the strong red-range photoluminescence (PL) with increasing Si concentration and annealing temperature. The appearance of the single peak in the PL is closely related to the c-Si NC formation. The PL also redshifts from ∼1.9 to 1.4 eV with increasing Si concentration and annealing temperature (i.e., increasing NC size). The good agreements of the PL evolution with NC formation and the PL peak energy with NC size distribution support the quantum confinement model.     

Laser applications in thin-film photovoltaics

We review laser applications in thin-film photovoltaics (thin-film Si, CdTe, and Cu(In,Ga)Se₂ solar cells). Lasers are applied in this growing field to manufacture modules, to monitor Si deposition processes, and to characterize opto-electrical properties of thin films. Unlike traditional panels based on crystalline silicon wafers, the individual cells of a thin-film photovoltaic module can be serially interconnected by laser scribing during fabrication. Laser scribing applications are described in detail, while other laser-based fabrication processes, such as laser-induced crystallization and pulsed laser deposition, are briefly reviewed. Lasers are also integrated into various diagnostic tools to analyze the composition of chemical vapors during deposition of Si thin films. Silane (SiH₄), silane radicals (SiH₃, SiH₂, SiH, Si), and Si nanoparticles have all been monitored inside chemical vapor deposition systems. Finally, we review various thin-film characterization methods, in which lasers are implemented.     

SiH4 adsorption on SiGe(0 0 1)

The adsorption process of silane (SiH₄) on a SiGe(0 0 1) surface has been investigated by using infrared absorption spectroscopy in a multiple internal reflection geometry. We have observed that SiH₄ dissociatively adsorbs on a SiGe(0 0 1) surface at room temperature to generate Si and Ge hydrides. The dissociation of Si- and Ge-hydride species is found to strongly depend on the Ge concentration of the SiGe crystal. At a low Ge concentration of 9%, Si monohydride (SiH) and dihydride (SiH₂) are preferentially produced as compared to the higher Si hydride, SiH₃. At higher Ge concentrations of 19%, 36%, on the other hand, monohydrides of SiH and GeH and trihyderide SiH₃ are favorably generated at the initial stage of the adsorption. We interpret that when SiH₄ adsorbs on the SiGe surface, hydrogen atoms released from the SiH₄ molecule stick onto Ge or Si sites to produce Si or Ge monohydrides and the remaining fragments of -SiH₃ adsorb both on Si and Ge sites. The SiH₃ species is readily decomposed to lower hydrides of SiH and SiH₂ by releasing H atoms at low Ge concentrations of 0% and 9%, while the decomposition is suppressed by Ge in cases of 19% and 36%.     

Preparation of thin Si:H films in an inductively coupled plasma reactor and analysis of their surface roughness

An important concern in the deposition of Si:H films is to obtain smooth surfaces. Herein, we deposit the thin Si:H films using Ar-diluted SiH₄ as feedstock gas in an inductively coupled plasma reactor. And we carry a real-time monitor on the deposition process by using optical emission spectrum technology in the vicinity of substrate and diagnose the Ar plasma radial distribution by Langmuir probe. Surface detecting by AFM and surface profilometry in large scale shows that the thin Si:H films have small surface roughness. Distributions of both the ion density and the electron temperature are homogeneous at h = 0.5 cm. Based on these experimental results, it can be proposed inductively coupled plasma reactor is fit to deposit the thin film in large scale. Also, Ar can affect the reaction process and improve the thin Si:H films characteristics.     

Formation of SiH bonds on the surface of microcrystalline silicon covered with SiOx by HF treatment

Infrared absorption due to the surface chemical bonds on microcrystalline silicon (μc-Si) was investigated with recycling procedures of thermal oxygenation accompanied with dehydrogenation and HF etching. SiH bonds were reformed on the surface of μc-Si by HF etching of oxygenated μc-Si. The mechanism of the SiH bond formation was proposed. It was suggested that formation of =SiH₂,

SiH₂

_x or -SiH₃ group depended on the kind of a crystalline plane.     

In-situ study on thermal decomposition of 1,3-disilabutane to silicon carbide on Si(1 0 0) surface

The intermediates of thermal decomposition of 1,3-disilabutane (SiH₃CH₂SiH₂CH₃, DSB) to form SiC on Si(1 0 0) surface were in situ investigated by reactive ion scattering (RIS), temperature programmed reactive ion scattering (TPRIS), temperature programmed desorption (TPD), and auger electron spectroscopy (AES). DSB as a single molecular precursor was exposed on Si(1 0 0) surface at a low temperature less than 100 K, and then the substrate was heated up to 1000 K. RIS, TPD, and AES investigations showed that DSB adsorbed molecularly and decomposed to SiC via some intermediates on Si(1 0 0) surface as substrate temperature increasing. Between 117 and 150 K molecularly adsorbed DSB desorbed partially and decomposed to CH₄Si₂, which is the first observation on Si(1 0 0) surface, and further decomposed to CH₄Si between 150 and 900 K. CH₄Si lost hydrogen and formed SiC over 900 K.     

Laser-induced chemistry in silane-hexafluoroacetone mixtures for production of novel Si/C/F/O and C/F/O materials

Chemical reactions induced by CO₂-laser radiation in mixtures of silane and hexafluoroacetone afford various gaseous silicon- and carbon-containing compounds and result in deposition of microstructures of carbon, C/F/O and Si/C/O/F materials. These products are suggested to be formed by a variety of exothermic reactions initiated through SiH₄-photosensitized decomposition of hexafluoroacetone. Silane is shown to be a very potent reagent for the reduction of C-F bonds.     

Evolution of infrared spectra and optical emission spectra in hydrogenated silicon thin films prepared by VHF-PECVD

A series of hydrogenated silicon thin films with varying silane concentrations have been deposited by using very high frequency plasma enhanced chemical vapor deposition (VHF-PECVD) method. The deposition process and the silicon thin films are studied by using optical emission spectroscopy (OES) and Fourier transfer infrared (FTIR) spectroscopy, respectively. The results show that when the silane concentration changes from 10% to 1%, the peak frequency of the Si—H stretching mode shifts from 2000 cm ^{- 1} to 2100 cm ^{- 1}, while the peak frequency of the Si—H wagging—rocking mode shifts from 650 cm ^{- 1} to 620 cm ^{- 1}. At the same time the SiH^*/H_α intensity ratio in the plasma decreases gradually. The evolution of the infrared spectra and the optical emission spectra demonstrates a morphological phase transition from amorphous silicon (a-Si:H) to microcrystalline silicon (μc-Si:H). The structural evolution and the μc-Si:H formation have been analyzed based on the variation of H_α and SiH^* intensities in the plasma. The role of oxygen impurity during the plasma process and in the silicon films is also discussed in this study.     

Modified growth of Ge quantum dots using C2H4 mediation by ultra-high vacuum chemical vapor deposition

C₂H₄ mediations were used to modify the Stranski-Krastanow growth mode of Ge dots on Si(0 0 1) at 550 °C by ultra-high vacuum chemical vapor deposition. With appropriate C₂H₄-mediation to modify the Si surface, the elongated Ge hut clusters can be transformed to highly uniform Ge domes with a high Ge composition at the core. These C₂H₄-mediated Ge dots, almost bounded by {1 1 3} facets, have an average diameter and height of 55 and 9 nm, respectively. We propose two major mechanisms to depict the formation of these C₂H₄-mediated Ge dots: (i) an almost hydrogen-passivated Si surface to limit the nucleation sites for dot formation, and (ii) the incorporation of Ge atoms, repelled by the C-rich areas, into the existing Ge dots. This work provides a useful scheme to tune the topography of Ge dots in an UHV/CVD condition for possible optoelectronic applications.